Search Documents

By A. F. Colombo, D. W. Frommer

Bench- scale tests were made to determine the applicability of flotation as a means of upgrading finished and semifinished magnetic concentrates prepared from reductively roasted iron ores . Both anionic and cationic flotation methods were used to remove siliceous gangue from the magnetic concentrates and produce upgraded products . Seven magnetic concentrates , containing from 6.7 to 13.7 percent SiO2 , were improved by the flotation treatment , yielding final concentrates containing less than 6.0 percent Si02 . Cationic flotation methods were studied on four of the seven samples ; of this group only one sample yielded better results by cationic flotation than by the anionic method .

Jan 1, 1964

By Ehsan Alavi, Brian Hagan, Colin LaVassar, Glen Frank, Derek Dugan, Rick Capka, Lisa Mori

"Tunnel face instability is one of the most common issues in EPB tunneling. The evaluation of an ideal face support pressure is a critical element in the design and construction phases of EPB tunneling. In this study, measured tunnel face pressures in three EPB tunneling projects (University Link U230 and U220 projects and the Northgate Link Extension N125 Project) for Sound Transit in Seattle, WA are compared with the calculated analytical methods. This comparison shows that the analytical methods generally overestimate the required tunnel face support. The best practice for managing the face pressure in EPB tunneling operation is discussed based on the experience gained through these projects. Furthermore, the algorithm that is developed for identifying ground loss in these projects is addressed. INTRODUCTION Earth pressure balanced tunneling relies on using muck within the chamber to support the face. Muck is pressurized by controlling the advance rate of the tunnel boring machine and the speed of the screw conveyor. Target face pressure is typically calculated by using the geotechnical assumptions in the geotechnical baseline report. The concept behind EPB tunneling is that the application of sufficient face support pressure will prevent tunnel face instability and the resultant over excavation. Tunnel face instabilities caused by a lack of sufficient face support can lead to ground loss and surface settlement (Anagnostou & Kovári 1996, Kirsch 2010). A certain support pressure must be achieved to counteract water and earth pressure with an adequate factor of safety. While the water pressure can be predicted accurately, the determination of the resultant earth pressure on the face is less precise. This becomes manifested in the relatively high partial safety factors on the earth pressure."

Jan 1, 2016

By Karina Forster

Rock mass characterisation is a critical component of effective stope design. Unexpected excessive stope dilution or uneconomic stope sizes can be the result of rock mass characterisation that is not representative of actual stope conditions. Comprehensive characterisation of the rock forming the stope hanging wall, back, ends and footwall is best done by a rock mechanics or ground control expert, however, this is time consuming and is often limited by available access. There are two general approaches for characterising a stope hanging wall for dilution estimating. Detailed classification and mapping data can be collected in local areas where good exposure is available. Personnel, exposure and time are usually not available to do a thorough analysis for all stopes. The stope hanging walls are then broken into lenses or domains and similar conditions are assumed for each area. The second approach consists of using readily available data such as RQD. Other rock mass properties which influence hanging wall behaviour are estimated based on back analysing a few case histories. Stope design is then based on the variability of the one parameter, such as RQD, that is consistently measured for the rock mass surrounding the ore body. This paper presents a third approach which looks, in depth, at the interpretation of geological core logging data for rock mass characterisation. Several rock mass properties that influence stope design, such as joint alteration, rock mass strength, joint spacing and orientations, have been linked to data collected by the mine geologists. This drill hole logging data was calibrated against underground mapping and used to back analyse the dilution prediction for mined-out stopes.

May 1, 2006

By Thomas J. Albin

This U.S. Bureau of Mines report identifies potential causes of slip-and-fall accidents occurring during surface mine equipment maintenance and describes the relative roles of direct worker behavior and machine design. The relative roles of human behavior and machine design in the causation of slip-and-fall accidents were determined through analysis of accident records, observations of maintenance worker behavior, and evaluation of mine machinery. From these data, relative risk ratios were calculated. Behavior had a relative risk ratio of 1.5; machine design, specifically access systems design, had a relative risk ratio of 2.2. Of the access systems, ladders had the highest relative risk ratio, 7.0. This study suggests that accident intervention would be most profitably made in improving the design of systems used to access maintenance worker areas of mining equipment.

Jan 1, 1990

By M. G. Premo

The McKinley Mine is located in the northwest New Mexico, in McKinley County, approximately 25 miles from Gallup. The mine is operated by The Pittsburg & Midway Coal Mining Co. (P&M), a wholly owned subsidiary of the Chevron Corporation. P&M is headquartered in Englewood, Colorado. Since the McKinley Mine began operations in 1962 a total of 83,391,000 metric tons of coal have been sold through 1990. The 1991 production was approximately 5.000.000 metric tons. The mine operations are contained on a 109.000 square kilometers lease area of which 44.000 square kilometers are on the Navajo Nation. The present customer base consists of four utilities and one industrial account, all of which are located in Arizona. The utility customers are the Arizona Public Service Co. Cholla Station at Joseph City, The Salt River Project. Coronado Generating Station near Joseph City, and The Tucson Electric Company, Irvington Generating Station in Tucson. The industrial customer is the Stone Container Corporation, Snowflake Paper Mill.

Jan 1, 1992

The workshop on "Cyanide Effluents from Mineral Processing' was held on February 2-3, 1982, at the U.S. Bureau of Mines, Salt Lake City Research Center, Salt Lake City, Utah. The workshop was sponsored by the minerals industry, supporting industries, the National Science Foundation, and the U.S. Bureau of Mines through the Utah Mining and Mineral Resources Research Institute, College of Mines, University of Utah Prior to the workshop, a Working Paper was prepared and delivered to the participants. This paper was used as a guide during panel discussions and forms the basis for this proceedings document. The workshop focused on use of cyanide as it relates to the gold and silver mining industry and the froth flotation processes employed by mineral mining companies. Its intent was to discuss "state of the art" technology and provide information pertinent to cyanide use in the minerals industry. No attempt was made to advocate regulatory limits or set policy governing the use of cyanide. The principal topics of discussion included- (1) the chemistry and use of cyanides; (2) control and treatment of cyanide mining wastes; (3) toxicity of mining wastes; (4) fate of cyanide in the environment; and (5) the analytical chemistry of cyanide.

Jan 1, 1983

By Linfeng Zhou, Rong Sun, Guanghui Li, Zhiwei Peng, Tao Jiang

Dust, or airborne particulate matter, from metal smelting can be either mechanically or thermally generated and it negatively affects the indoor air quality as well as the fugitive emissions from the plant. The thermally generated dust is often referred to as fume and it is typically generated whenever liquid metal comes into contact with air. For practical reasons, such as vehicle access, etc. it is often difficult to collect 100% of the fume. It is therefore highly desirable to develop processes and optimize operational procedures so that fuming can be kept to a minimum. In this series of experiments, the mechanism of active oxidation and fume formation from liquid silicomanganese under an impinging air jet in the temperature range 1400-1600°C has been explored. Characteristic properties of the fume have been established; particle diameter, shape, size distribution, and elemental composition are reported. The oxidation process is described in terms of vaporization, oxidation and agglomeration. In the boundary layer, two competing mechanisms seem to be operative in parallel: a direct oxidation of Mn vapor, and a two-step oxidation of silicon. The thermodynamic and kinetic conditions governing the two mechanisms are discussed.

Jan 1, 2016

By C. M. Harrer

This paper describes the location, features, qualities, extent, and potential of iron occurrences and some associative resources -limestone and dolomite, coal, petroleum and natural gas, power, and water - in New Mexico. Reconnaissance investigations were made of 118 iron occurrences to deter-mine their extent, attitude, and potential; character samples were analyzed to determine their quality and impurities; and pioneer metallurgical investigations were made on character samples to present their metallurgical problems. Some factors influencing past and potential iron markets are discussed. The most abundant iron minerals are magnetite and hematite. The higher grade deposits are extensive contact-metamorphic and pyrometasomatic replacements in calcareous Paleozoic rocks associated with intrusives. Low-grade deposits of considerable potential are the extensive Cambrian oolitic hematites of sedimentary origin and the Precambrian magnetite-hematite taconite iron formation. Iron occurs also as extensive colluvial and alluvial concentrations. A wide variety of accessory elements are indicated and these pose metallurgical and economic problems.

Jan 1, 1963

By Marcie A. Greenberg

The Fence Lake Project is located in the Salt Lake coal field, an extension of the San Juan Basin. Geologic formations exposed in the Project area range in age from late Cretaceous to Quaternary. Coal is encountered in the Moreno Hill Formation (upper Cretaceous). Salt River Project (SRP) followed the basic textbook approach for the exploration, regional appraisal, detailed reconnaissance, detailed surface appraisal and three dimensional sampling (physical exploration). SRP is exploring this property as a potential fuel source for the Coronado Generating Station. Therefore, for the physical exploration stage, the quality sampling program was designed from a utility company viewpoint to determine possible impacts to the Station. Exploration drilling was completed in spring, 1982; September, 1982, and summer, 1984. Engineering, environmental, and land acquisition studies were added in the Summer, 1984 Program to more closely evaluate the potential Fence Lake Project coal supply option for the Coronado Generating Station. Studies, including drilling, are ongoing-at this time.

Jan 1, 1984

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By Jamal Jafari, Abbas Sam

"The concentration of the fourth production line at Golgohar includes 66% iron with Blaine number of 500 cm2/g. For pelletizing process, the feed iron grade should be greater than 68% with minimum Blaine number of 1800 cm2/g. In this study, the low intensity magnetic Separators, particularly the feed particle size distribution of LIMS were considered. The feed particle size distribution of the separators was optimized to prepare an appropriate concentrate (as mill pelletizing feed). The samples were performed from the LIMS feed and after grinding, four d80 (64, 103, 132, and 15 3µm) were prepared. Then, laboratory magnetic separation experiments were conducted on these samples. The best results obtained using d80 of 132µm. In this particle fraction, the iron grade and Blaine number were 70.3% and 1571 cm2/g, respectively. Therefore, it seems necessary to include a grinding and classification systems before LIMS stage. According to the presence of a high amount of -132 µm particles in the initial feed, an inverse closed circuit was selected. The hydrocyclone was designed in three units as the classification system with 62 cm (diameter), 22 cm (overflow outlet) and 11 cm (apex diameter). By simulation of hydrocyclone with USIMPAC software, the size distribution of underflow was determined. Based on these results, a ball mill with dimensions of 6.7 m (length) and 5 m (diameter) was designed as grinding system.INTRODUCTIONGole-Gohar iron ore concentration plant No.4 (Polycom Plant) in Gole-Gohar Industrial and Mining Complex was installed to increase production capacity as well as treating the circulating load from AG and SAG mills of the main concentration plant of the complex. The load from the mine is crushed using jaw and cone crushers. The crushed ore is then combined with the circulated load and the combination is then grounded using HPGR and ball mills respectively.After comminution, there is a magnetic separation plant which includes a medium intensity magnetic separator (MIMS) followed by three low intensity magnetic separators (LIMS). Final concentrate dewatering is done using three belt filters. After the primary magnetic separation, the ore is upgraded to 62% Fe content and final concentrate which is the product of LIMS has 66% Fe content."

Jan 1, 2016

By C. W. Armbrust

At FHC Gold Company's Paradise Peak Mine gold and silver are produced. Precious metals recovery rates are very satisfactory along with the recovery and production of a relative high volume of mercury. At Paradise Peak precious metals are recovered via the Merrill-Crowe process and delivered to the refinery area as a mercury-bearing precipitate cake. The recovery of mercury is then obtained through a vacuum retort system. The balance of the material is mixed with fluxes and then melted and cast into dore' bars for shipping. Issues of retort capacity and concerns over efficiency led to research into the retort process itself.

Jan 1, 1990

By Gary MacDonald

What is the primary function of an impact assessment? Many people at the International Association of Impact Assessment?s (IAIA) annual conference said that it is time to return to the fundamentals and consider the underlying drivers of impact assessments ? human health, safety and security. This fall, managers struggling with those fundamentals will receive extra support when a new course focusing on health and socially responsible security is launched online and in British Columbia, Canada, home to many of the world?s junior miners. Now in its 33rd year, the IAIA conference recently held in Calgary, Canada, typically brings together a range of professionals who work in the impact assessment field, including academics, as well as people conducting applied disciplines, such as social and environmental performance management. It is a chance for people grappling with how to assess impacts from projects (for example, dams, mining and other extractive projects), to compare notes and to talk about developments in how to measure, track and report on them. The comments about returning to fundamentals rose as participants talked about the ongoing and increasingly recognized divergence between three main impact assessment streams: environmental, social and health (EIA, SIA and HIA, respectively). Discussions in sessions and in the corridors included calls for streamlining, for integration, for improvement and sharing of practice ? particularly in the HIA stream, where those deeply engaged in the health discipline questioned how HIAs and their intended outcome of protecting human health can be better integrated into the EIAs or SIAs that dominate the impact assessment realm. EIAs and SIAs have become the main tool, particularly from a permitting perspective for large-scale mines, but seem to leave projects with little real information about what they need to do. Human health is not the only concern re-emerging. Although not reflected at the conference, there appears to be an emerging understanding of the need to link the determinants of health with socially responsible security practices. Companies conducting independent social performance assessments for international financial institutions based on the International Finance Corporation?s Environmental and Social Performance Standards increasingly wrestle with both community health and security issues as extractive companies encounter challenging social environments around the world. Once again, the intended outcome is to better protect human health, including avoiding health impacts from conflict, abuses and violence.

Aug 1, 2013

By J. F. Henderson

THIS paper relates to an area of more than 5,000 square miles in the Northwest Territories extending north from Great Slave lake and including-the Yellowknife, Beaulieu River and Gordon lake areas. Within the last three years much interest in the area has been created by the discovery of remarkably rich gold-bearing veins and the realization that thousands of square miles of unprospected ground are underlain by rocks like those in which the veins have been found. Probably there were more prospectors in this area in 1938 than in any other part of Canada. The area lies 650 miles north of Edmonton, and 425 miles north of the terminus of the Northern Alberta railway at Waterways, Alberta. The Athabaska and Slave rivers provide an excellent water route from Waterways to Great Slave lake for large oil and wood burning boats and barges which operate from the latter part of May to October. The only portage is around a 16-mile stretch of rapids on the Slave river between Fort Fitzgerald and Fort Smith. The town of Yellowknife, on the north side of Great Slave lake, has sprung into existence during the past year and is the centre for distribution of supplies for the Yellowknife-Beaulieu region. The Con-Rycon and Negus gold mines, which came into production in September, 1938, and February, 1939, respectively, lie about two miles south of the townsite. Excellent airplane service is available from Edmonton to Yellowknife and from Yellowknife to all parts of the area. The prospector and mining operator have come to rely almost entirely on the airplane for supplies and for the transportation of personnel, camp equipment, and canoes from Yellowknife to localities selected for intensive prospecting.

Jan 1, 1939

By R. S. Dean

The original flotation reagents were certain oils selected for a combination of properties that occurred fortuitously. It was recognized quite early in the study of flotation mechanism that, in order to function, an oil must have an active group-one that differs from the remainder of the molecule in its affinity for water or the mineral particle. Wark4 gives credit for recognition of this elementary chemical principle to the senior author of this report.5 However, it was soon found that simple hydrocarbons could not be used as flotation reagents and that two of the functions, which were combined in the early flotation oils such as pine and eucalyptus, could be obtained in separate compounds and their relative intensity controlled to advantage. These two functions were called collecting and frothing.

Jan 1, 1944

By K. D. Dill, S. D. Rosenthal

"This project analyzed the efficiency of incorporating the use of directional drilling technology into coal overburden blasting. Directional drilling is currently in use in the petroleum industry and it is believed that it will be a valuable asset in the mining industry. This project has shown that directional drilling can be a viable technology for use in the coal overburden removal process resulting in increased drill utilization and potential for cost savings. Future work regarding blasting and geotechnical evaluation should be performed to solidify the concept. INTRODUCTION Determine the Potential Drill Utilization Improvements and Rock Fragmentation Requirements Using Directional Drilling in a Coal Mining Overburden Highwall Application was a project funded by Atlas Copco Drilling Solutions (Atlas Copco) based in Garland, Texas. The project was developed and researched by Montana Tech of the University of Montana. This project was intended to show how the use of directional drilling can increase drill utilization, while decreasing costs, without sacrificing overburden blasting results. This paper discusses a review of the literature, the methods performed, conclusions and future work Background Atlas Copco theorized that an alternative approach to drilling a cast blast pattern would be beneficial to coal mining operations by increasing drill utilization and therefore, decreasing overall costs. Increasing drill utilization results in an increase in the amount of time the drill is being productive, more drill bit time in ground. Atlas Copco’s theory is that by incorporating directional drilling in the design of a cast blast pattern, a drill rig could drill multiple directional holes, which are the length of the cast blast, from a single drill set up. A drill goes through a series of steps to complete a blast pattern, these steps include: tramming to the hole location, leveling the drill, drilling the hole, cleaning the hole, and retracting the drill steel. This process is repeated hundreds of times until the whole pattern is completed. The most time intensive part of this process is drilling out the blast pattern. Integrating directional drilling into this process could decrease the overall time it takes to drill out a blast pattern by minimizing the amount of time spent tramming and setting up for each subsequent hole. Tramming and drill set up are two aspects of the drilling process where the drill tool is not engaged with the ground and, therefore, not being utilized. A cast blast pattern designed to utilize directional drilling will allow the drill tool to be “in the hole” longer and will improve drill utilization. This change in drill utilization was analyzed. Drilling and blasting is an integral part of the mining process, without it mining would be a slower process and less material could be mined. Drilling provides holes for explosives to be loaded and then blasted. Blasting has been found to be the most cost effective method of fracturing rock in mining for material removal. Blasting is also used as a low-cost method to move the rock in open cast mines, commonly referred to as cast blasting. A cast blast is a large blast designed to allow for the maximum amount of overburden to be removed using explosives in a single blast thereby uncovering more coal at a lower cost. Not all the material is blasted to cast-to-final, which requires that material to be moved with large mining machinery. Material that is considered cast-to-final is material that has been thrown far enough to never be moved again in the coal extraction process, therefore it is in its final resting place. A typical cast profile and cast-to-final area is shown in Figure 1."

Jan 1, 2017

By A. B. Holland-Batt

Deposition velocities play an important role in many fields of engineering and an impressive range of measured data has accumulated in the literature. Numerous workers have addressed the problems that are associated with the prediction of deposition velocity because of its particular relevance to the design of pipelines and pumping stations. However, despite this extensive effort, the calculation of friction heads still requires reference to experimentally based graphs to determine Durand factors and there is still scope for improvement in the prediction of the deposition velocity at different solids concentrations. Equations to characterise the relationship between the Durand factor and the volume concentrations of solids in the slurry are presented. A correlation for the prediction of the deposition velocity is also developed and tested against some of the classical experimental data. The application of predicted values of deposition velocity in assessing the potential for the sanding-up of spiral separators is then described and a case study is presented.

Jan 12, 1992

By Frank C. Morris

This report presents the results of a Bureau of Mines study to identify clays found in several petroleum-reservoir rocks in the Tejon-Grapevine area, Kern County, Calif., and to determine the effect of water sensitivity of the clays on the permeability of the reservoir rocks. The clays in the porous rocks were examined in detail, and the clay-mineral types were identified by differential thermal analysis, X-ray diffraction, and optical and dye-staining methods. Fresh-water damage to the permeability of the oil-reservoir rocks was indicated by a study of 125 core samples from productive formations. The study indicated that, although clays were generally less than 5 percent of the reservoir rocks, they swelled in water, particularly fresh water, and nearly blocked the flow channels through which oil flows to the well, effectively reducing the permeability of the formations. The average permeability of rock decreased from 1,600 millidarcys in air to 620 millidarcys in salt water and 120 millidarcys in fresh water. The dominant clays in the oil-bearing sandstones were members of the montmorillonite group. They were associated with smaller quantities of clays found to be in the mica or illite group. None of the cores appeared to contain clays of the kaolinite group. In the lower section of the J.V. sandstone indications of what appeared to be the mineral sepiolite were noted.

Jan 1, 1959

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972