Search Documents

By Oliver Bowles

The wire saw, introduced by the Bureau of Mines about two years ago, has revolutionized slate quarrying in Pennsylvania. The success of the saw since its early accomplishments has become greater and greater as the equipment has been perfected and skill acquired .in its use. In the first test made, a cutting rate of 9.7 square feet per hour was attained; in the next four cuts, made early in 1927, the average rate of cutting was increased to 12.8 square feet per hour; in 1928 a maximum of 34 square feet per hour had been attained, with a general average of about 20 to 25 square feet, The wire saw is now regarded as essential equipment in practically all of the quarries in the Bangor, Pen Argyl, and Windgap districts. The wire saw consists of a three-strand steel cable of 3/16 or 1/4 inch diameter running as an endless belt. The driving pulley is a 40-inch double-groove cast-iron sheave. A tension pulley supported by a frame mounted on wheels may travel back and forth on a short track. A weight of 800 to 2,000 pounds gives the desired tension on the wire. The driving units consist of electric motors with direct-drive compactly enclosed gear reduction, or double-belt speed-reduction units; the former is preferred. Silent chain and. pinion gear reductions are used to a limited extent. The travelling speed of the wire is about 15 feet per second. The driving and tension equipment are shown in Figure 1, A.

Jan 1, 1929

By C. P. Bowie

For years many oil producers have believed that often low-pressure oil- and gas-bearing strata have been over coked in fields where the rotary system of drilling has been used. Collom3/ gave as a reason for this condition that because the mud fluid was thick, the oil or gas stratum was plastered and sealed as the tools passed through it and no oil showed at the surface. Although this observation was made 15 years ago, it may often still be true notwithstanding modern developments in coring and electrical logging. Operators have believed, also, that mud fluid does not solidify behind the casing. Lewis and McMurray4/ stated: "All the evidence obtainable from practical experience points to the fact that the mud fluid properly mixed and employed does not solidify behind the casing, even in deer wells and after long periods."

Jan 1, 1937

By H von Blottnitz, J L. Broadhurst

Eco-efficiency has been proposed by the World Business Council on Sustainable Development as an environmental performance indicator framework that contributes to sustainability by assisting corporate decision makers improve the environmental performance of their operations and processes, while also extracting additional economic value. Given that the recent engagement of the minerals industry with sustainability has highlighted the need for requisite tools and methodologies, it is therefore of interest to assess whether eco-efficiency indicators can drive sustainability performance improvement during process design within the minerals industry. Previous work indicates that the choice of sustainability performance indicators to be used for decision making needs to be governed by the decision context; ie the performance indicators need to be fit-for-purpose. Here, the strengths and weaknesses of eco-efficiency indicators are analysed using case studies. First, a more rigorous definition of eco-efficiency indicators for the minerals industry is proposed based on indicators currently offered in the literature. Two case studies are then selected to reflect typical decision situations encountered within minerals process design. For each case study, eco-efficiency indicators are computed and are compared to more traditional graphical representations of the economic and environmental performance of process design alternatives considered. The sensitivity of these indicators to various process design parameters is also investigated. Results confirm that the meaningful application of eco-efficiency indicators is strongly dependent on the decision context in which the process data is generated. Results also show that eco-efficiency indicators can be related to technical process design parameters to allow for richer communication of performance information for various decision trade-offs; however, in some cases, graphical approaches that provide more insights into the environmental-financial trade-offs should be preferred. The research thus contributes to guiding the selection of the appropriate tools for more environmentally sustainable design of minerals beneficiation processes.

Jan 1, 2009

By G. Mbuyi Kamba

Literature is rather abundant on the topic of steady-state network analysis programs. Many versions exist, some of them have real extended facilities such as full graphical manipulation, fire simulation in motion, etc. These programs are certainly of great help to any ventilation planning and often assist the ventilation engineer in his operational decision making. However, what ever the efficiency of the calculation algorithms might be, their weak point still is the overall validity of the model. This numerical model, apart from maybe the questionable application of some physical laws, depends directly on the quality of the data used to identify its most influencing parameters such as the passive (resistance) or active (fan) characteristic of each of the branches in the network. Considering the non-linear character of the problem and the great number of variables involved, finding the closest numerical model of a real mine ventilation network is without any doubt a very difficult problem. This problem, often referred to as the parameter adjustment problem, is in almost every practical case solved on an experimental and "feeling" basis. Only a few papers put forward a mathematical solution based on a least square approach as the best fit criterion. The aim of this paper is to examine the possibility to apply the well-known simplex method to this problem. The performance of this method and its capability to reach the global optimum which corresponds to the best fit is discussed and compared to that of other methods.

Jan 1, 1995

By D. D. Gertenbach

"The successful commercialization of a pressure oxidation (POX) process for recovering metal values, including gold, copper, zinc, nickel and molybdenum, is the result of a carefully planned development program. The initial task involves developing one or more conceptual flowsheets, including the POX autoclave and downstream purification and recovery steps. A laboratory program is completed to determine the technical viability of the flowsheets, define the operating parameters for each step and provide information for an initial economic assessment of the process. The process is then confirmed during a continuous pilot plant program, providing engineering design data and other information for the commercial design. A well-thought-out development program has been shown to be critical for reducing the risk of commercializing POX processes. Experiences developing POX processes for refractory gold ores and copper concentrates are briefly discussed. IntroductionPressure oxidation (POX) has become a common commercial operation for processing sulfide-bearing feedstocks. These feedstocks include gold ores and concentrates; copper concentrates; nickel concentrates and mattes; zinc concentrates; and molybdenum concentrates. Drivers for the development and commercialization of POX processes include:• The high cost for pyrometallurgical processing of sulfide ores, much of which is attributed to environmental controls.• The motivation to implement safe and more environmentally attractive alternatives for sulfide ores.• The need to process increasingly difficult ores with complex mineralogy.• Improvements made over the last 25 years in POX equipment design and experience operating commercial POX plants.Although the capital and operating costs for commercial POX processing can be high, this technology is capable of rapid oxidation of most sulfides and arsenic minerals in the feed, with little noxious gases and environmentally stable iron arsenate and other iron compounds in the POX residue (Marsden and House, 2006).In POX operations, sulfides are oxidized to either sulfates or elemental sulfur in an autoclave at elevated temperature and pressure with oxygen gas. An example is the overall oxidation reactions of chalcopyrite when sufficient oxygen is present, shown in the following reactions:"

Jan 1, 2016

By G Capes, L Morizzi, N Mitkas, E Jones, D Grant

This paper describes the mining setting for the sub-level open stoping (SLOS) mining method used at Olympic Dam (OD), and investigates the range of stope performance conditions encountered over 30 years of production, using a qualitative description of the factors influencing performance. Utilising a continuous improvement tool, the Plan-Do-Check-Act (PDCA) process, and a forward-looking rock mechanics program, the intent is to identify the key factors driving productivity and performance to create a stable and achievable long term mine plan.

Mar 15, 2021

By W. R. McClelland

GOLD-BEARING ores, representing many types, are found widely distributed through the Province of British Columbia. They range from those which by their nature may be considered as complex, to those whose mineral characteristics are simple. Those in which the gold is associated with metallic sulphides provide particular milling and metallurgical problems, the solution of which involves not only detailed laboratory investigation but also a careful consideration of economic factors. The location of an ore-body may have a deciding influence on the adoption of a method for the metallurgical treatment. Whether the ore should be treated with the object of recovering the gold as bullion or as a shipping concentrate is often dependent on such topographical considerations as the position of the mine at or near tidewater or within a reasonable overland distance of a smelter. British Columbia is fortunate in having the Trail smelter situated in the southern part of the Province, and the smelter at Tacoma, Washington, is accessible for coastwise traffic. Both of these provide a ready market for most types of gold-bearing concentrate. In order that the results obtained by laboratory tests may give a fair indication of what should follow in mill operation, it is essential that the test sample should represent as closely as possible in mineralogical character and in grade the ore that eventually will constitute the feed to the mill. In the early stages of mine development this consideration is sometimes overlooked and samples of a much higher grade than would be representative of run-of-mine ore are submitted. Flotation tests on such a sample of ore high in sulphides may show a low ratio of concentration, bu.t if the actual run-of-mine ore is lower in sulphides the mill operation will reveal a much higher ratio. The recommendations for treatment based on the results of laboratory tests may have been against concentration, when in actual operation this would be the most suitable method of treatment. Recommendations based on laboratory tests are necessarily from the results of work carried out on the sample submitted, modified only by such other economic or topographical information as may be known to the investigator. This paper deals with a few of the gold ores found in the six mining districts of British Columbia and is based on investigations made in the Ore Dressing and Metallurgical Laboratories of the Mines Branch, Department of Mines, Ottawa.

Jan 1, 1937

By Robert Kimutis, Heather Dougherty, Eric Watkins

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry as a predictive tool for planning and monitoring and can assist with a well breach scenario over a large mining area. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Oct 12, 2023

By Ernest W. Hilton

The purpose of this investigation was to assess the environmental impact of the surface mining methods currently used in the steep-sloped areas of Central Appalachia: southern West Virginia, eastern Kentucky, southwestern Virginia and northeastern Tennessee. Comparisons are made between mountaintop/cross ridge mining, contour strip, augering and an innovative method surface shortwall mining which was attempted at Julian, West Virginia. Included in this final report are a discussion and analysis of current Appalachian production, reserves, and the extent of land affected on a county- by-county basis. Additionally, the seams within the steep sloped region have been assessed according to minimal standards of thickness, surrounding lithology, and areal extent to determine their amenability to surface shortwall mining. These seams have been tabulated with their ash, sulfur, and BTU content on a county-by county basis. Only minimal statements are made concerning quantity because of the narrow set of conditions required by the shortwall method. Other sections deal with the possible technical failings of an operational surface shortwall system based on field studies at shortwall operations, discussions with people experienced with shortwalls and research into ground control problems at sites where short- and longwall operations have been monitored. A final section details proposed additional research directions which the Bureau might take in the future.

Jan 1, 1979

By Ana Chiquini, Clayton V. Deutsch

The most common approach used in the mining industry for mineral resources modeling is to estimate the grades using ordinary kriging and report the recoverable resources based on this deterministic estimated model. Mineral resources calculated with kriging are a smooth representation of the actual distribution of grades and do not provide an assessment of uncertainty. Unlike kriging, simulation reproduces the variability of the grades in the mineral deposit and provides an assessment of uncertainty. Reporting mineral resources directly on high-resolution simulation results would assume perfect knowledge of the grade at the time of mining and selectivity at the scale of the data. There will always be uncertainty left at the time of mining, so assuming perfect knowledge of the grade in the future is incorrect. There are two concerns when geostatistical simulation is used for resources modeling: the information and the mining selectivity effects. A new framework for resource estimation is proposed with two separate modules to address those concerns. The information effect is accounted for by anticipating the additional production data that will be available at the time mining to guide the destination for the mined material. The mining selectivity effect is addressed by mimicking the grade control procedure to get mineable dig limits at a chosen selectivity, represented by a minimum mineable unit size. In addition to a prediction of recoverable resources that will be closer to the material mined in the future, the framework proposed provides an assessment of local and global uncertainty for risk management.

May 26, 2020

By S Harrison

Work health and safety duties around Australia include duties to manage psychosocial health and safety (mental health) of workers engaged by businesses or undertakings and of other persons impacted by the operations of the business or undertaking. Persons conducting a businesses or undertakings must develop systems of work and policies and procedures for ensuring, so far as is reasonably practicable, the safety and health of workers and other persons. Officers have a duty to exercise due diligence and to ensure effective systems are developed, implemented and resourced. The developed systems will only be effective with worker’s co-operation and engagement. The duties placed on workers by work health and safety laws are an important part of the safety matrix of obligations. Supervisors and Leaders are workers and they play a critical role in delivering health and safety outcomes. To deliver these health and safety outcomes with respect to psychosocial safety Supervisors and Leaders need to understand their obligations and have a framework to use to assist them in understanding what workers require and what steps need to be taken to meet their duties. They also need to take steps to assist those workers that they supervise to meet their duties.

Apr 16, 2024

By Robert Hopler

True there is a certain proportion of nitro-glycerin in dynamite cartridges, but the dangerous explosive is scientifically compounded with wood pulp and some other ingredients in such a way that it can be absolutely depended upon not to explode accidentally if our simple and plain instructions for its use are complied with.

Jan 1, 2012

By D. Harrington

The primary objective of this paper is to discuss the hazards and furnish a list of recommendations for the safe operation of quarries and related works. They have been compiled from Bureau of Mines publications covering the safety experience of engineers before and during the year in the mineral industry,5 from a publication of the National Safety Council, Inc.,6 from explosives recommendations made by various explosives manufacturers,7 and from suggestions obtained from quarries visited. The second objective is to describe and illustrate safety devices, practices, and quarrying methods. The quarrying and related industries of the United States had a lower accident-frequency rate than either the metal- or coal-mining industry as reported for 1942.8 However, the quarry industry ranked eleventh in 15 major industries during 1942 in lost-time accident fre¬quency; metal mining ranked fourteenth and coal mining fifteenth.

Jan 1, 1950

By A Chandra, P Guj

Only a few complex real options can be valued using closed-form equations, such as the Black and Scholes formula, because these algorithms are restrictive and prevent the construction of practical project evaluation models. Although a binomial lattice method paired with the ærisk-neutral probabilityÆ provides an easier and flexible modelling of exploration and mining projects, it has limitations when projects are complex, long-lived and influenced by the interplay of various market and private uncertainties. In order to overcome these limitations, modern decision tree software using dynamic programming capability can be used for real option valuations. This is a powerful computational tool in which the impact of various sources of uncertainties can be differentiated, so that the optimal decision path can be explicitly displayed visually. There has been significant academic controversy surrounding whether different real option (RO) valuation methods would lead to different real option values (ROV). This paper, using a realistic copper mining example, demonstrates that as long as the same degree of subjectivity and consistency are used in different real option valuation methods, they yield the same result. This conclusion is valid irrespective of whether the cash flow volatility generated by various sources of uncertainties is handled in an aggregated or in an explicit and differentiated manner. This paper compares two choices for an investor either to æbuy now and developÆ a project or to enter into a ætwo-year option to purchaseÆ after the proponents have developed it. It also shows how significantly different net after-tax operating cash flows may be generated by these different choices on the same underlying asset represented by the project. This is due to the difference in the amount and timing of the relevant capital investments affecting the depreciation and amortisation charges and as a consequence, the income tax paid. CITATION:Guj, P and Chandra, A, 2012. Real option valuation of mineral exploration/mining projects using decision trees - Differentiating market risk from private risk, in Proceedings Project Evaluation 2012 , pp 177-188 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By AIME AIME

A COMMITTEE, representing a number of the larger oil companies in California, met in San Francisco on Nov. 12, 1919, for the purpose of discussing the depletion deductions to be allowed in computing the Federal income taxes under the Internal Revenue Act of 1918. It was the general sense of the committee that a system based on sound engineering principles should be formulated for estimating the value of oil properties, so that better and more uniform results might be obtained by the various companies in filing their returns with the' Bureau of Internal Revenue. A subcommittee, consisting of five petroleum engineers, was thereupon appointed to collect information and draft a report. The committee consisted of G. C. Gester, Carl H. Beal, J. H. G. Wolf, E. G. Gaylord, and E. D. Nolan; this report is the work of that subcommittee.

Jan 1, 1920

By J. E. Kemp

1. Situation.—From Monterey in the State of Nuevo Leon, the Sierra Madre mountains stretch away to the southeast and present a steep front to the northeast. The Monterey and Mexican Gulf railway. which connects Monterey with Tampico. follows their general line with its road-bed a few miles out from the foothills. At a distance of 100 miles from Monterey it passes through the town of Linares. and from Linares one can see far away to the southeast the peaks of another group of mountains rising from the general plateau and forming a more eastern

Jan 1, 1906

By Eleanor Abshire

This bibliography is the result of a cooperative project undertaken by the Bureau of Ships and the Bureau of Mines to accumulate literature published to date on zirconium and hafnium and to establish an information center on these metals for the use of any interested research organization or library. This bibliography, which will be supplemented as additional information is accumulated, consists of references, with abstracts, to pertinent literature on the subject published from 1907 to date.

Jan 1, 1957

By A. A. Paoli

The selection of a mining plant for carrying on development work presents many problems distinct in themselves, and affected by various local factors. In this paper, the writer proposes outlining and discussing in some detail the chief factors governing the economic selection of such plants. This will be followed by an enumeration of the underground and surface plant required for carrying on several hypothetical exploratory and mining operations. Where it is impossible or not convenient to obtain hydro-electric power, and where wood for fuel is scarce, we now find oil engines being used. A 100 h.p. oil engine, such as would be required to operate a three-drill air compressor, consumes approximately five Imperial gallons of fuel-oil per hour at full load. On the basis of a 60 per cent load factor, this gives, for eight hours' operation, a probable actual consumption of twenty-four Imperial gallons.

Jan 1, 1929

By L. A. Haas

The Bureau of Mines, in cooperation with three Minnesota agencies (Department of Natural Resources, Geological Survey, and the Iron Range Resources and Rehabilitation Board), investigated the potential of using glacial lake clay from Minnesota, as well as other areas, as a binder for iron ore pellets. The best clay-characterizing procedures for predicting binder effectiveness were the cation exchange capacity (CEC) using the methylene blue method and the plate water absorption test (PWAT). The best clay binder was found in the Red River Valley. However, compared to a typical western bentonite at the 0.5-pct-addition level, addition of about 2 pct Minnesota clay was required to obtain comparable unfired (green) pellet strengths. Soda ash addition only slightly improved the binding properties of Minnesota clay, but considerable improvement was obtained by the addition of a small quantity of water absorbing organic compounds. For example, with a mixture of 0.5 pct Minnesota clay or paint rock and 0.1 pct pregelatinized starch, the unfired and fired physical pellet properties were about the same as with 0.5 pct of typical western bentonite. The reduction rate at the 40-pct reduction level and the percentage of plus 6.3-mm particles from the reduction disintegration index test were also about the same.

Jan 1, 1987