Search Documents

By C. Sunderman, G. Feagan, C. Stazick

Galvanic corrosion between dissimilar materials, such as steel and graphite, leads to safety concerns for many industries, including mining. In this study, researchers from the National Institute for Occupational Safety and Health (NIOSH) analyzed rock samples from two mines in the United States that exhibit electrochemical properties similar to graphite through laboratory measurements to investigate their observed in-situ influence on underground metal support. Uniform corrosion rates of mild steel coupons, inflatable bolt coupons, and friction bolt coupons galvanically coupled to rock samples were obtained using both potentiodynamic polarization and zero resistance ammetry. Increased uniform corrosion rates were witnessed between the coupled rock and steel system, over those of just the steel alone. Surface analysis of the metal samples showed the presence of pitting corrosion, reflective of bolt samples removed from partner mines. Corrosion pitting of ground support structures in contact with graphitic rock in underground mines poses safety concerns for mine workers by increasing the rate of corrosion and decreasing bolt strength over time and will be further investigated for intervention strategies.

Feb 1, 2023

By K. T. Stafford, N. A. Iverson, V. T. McLemore

Laramide porphyry copper deposits are large, low grade (<0.8% Cu) deposits that contain disseminated copper minerals, breccias, and stockwork veinlets of copper and molybdenum sulfides associated with porphyritic intrusions in Southwestern New Mexico. Critical minerals, such as PGEs, tellurium, indium, germanium, and gallium are recovered from the anode slimes remaining after copper is refined. Detailed age dating, mineralogy, geochemistry, along with geologic mapping could refine the location of critical minerals within specific systems and could identify porphyry systems with elevated critical minerals that could become economic, in addition to the already produced copper, gold and molybdenum.

Feb 1, 2023

By R. Gorakhki, R. Stafford, A. Jung

Geosynthetic clay liners (GCLs) have been used widely as an alternative for compacted clay liners and covers in mine waste applications. The high swelling of bentonite particles in the GCL creates a uniform barrier layer that results in low permeability of water and mine waste leachate. GCLs must provide sufficient internal and interface shear strength stability, especially if GCLs are used in steep slopes under high normal loads. Peel strength is a common parameter that is typically correlated to internal shear strength properties of GCLs. The relationship between internal shear strength and peel strength of GCL at normal stresses of 287, 575, 862, and 1724 kPa is evaluated in this study. The data in this study was compared with the peel strength-internal shear strength relationships found in literature. The study concludes that the relationship between peel strength and internal shear strength is unique based on manufacturing, needle-punching density and the method with and without heat treatment of the geotextile end fiber bundles.

Feb 1, 2023

By M. S. Moats, W. C. Hartzell

The stable domestic supply of gallium, indium, and germanium has been identified as a critical need for the United States. Electric arc furnace dusts, processed to recover zinc, produce a residue that could be a potential source of these critical materials. An industrial zinc leach residue was characterized to determine its particle size, chemical composition, and predominant mineral phases. Heated, atmospheric, agitated leaching using sulfuric acid and hydrochloric acid was examined to determine the extractions of gallium, indium, and germanium as a function of concentration and temperature. Extractions of gallium were found to be similar to iron in all experiments. The maximum percentage of Ga, Ge, and In leached into solution were 71%, 63%, and 48%, respectively.

Feb 1, 2023

By S. J. Cohen

Changes in our energy, national security, and commerce needs have necessitated identification of new sources of minerals, such as rare earths, lithium, copper, silver, aluminum, titanium, and the minerals on the U.S. Geological Survey’s (USGS) list of critical minerals (USGS, 2022). With the need to domestically produce these minerals, more mining will be required within the U.S. Some of these critical minerals deposit with naturally occurring radioactive materials (NORM), therefore, mining these minerals may concentrate NORM to the point that some states may require licensing and radiation protection programs. NORM is not regulated by the Federal government; it is regulated by the individual states. Consequently, overall national state of NORM regulation is chaotic with each individual state either choosing to regulate or not regulate NORM, and, if a state chooses to regulate NORM, then that state develops its own unique regulations. Further complicating the regulatory environment, states utilize a wide variety of strategies for regulating NORM, which sometimes results in inappropriate regulations, inconsistencies with specific radionuclides that are regulated, and inconsistencies with specific NORM types that are regulated. This paper will review the nature of NORM regulations, identify regulatory traps, and provide general guidance for identifying NORM and potentially avoiding regulatory jeopardy. Because of the chaotic nature of NORM regulations nationally, seeking guidance from qualified professionals with relevant expertise is recommended. Also, contacting the appropriate regulatory agency to gain a complete understanding of the NORM regulatory environment is useful for maintaining compliance.

Feb 1, 2023

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By A. Almeida, D. Castro, K. Ingmarsson, D. Ferreira, R. Tamir

Mine-to-mill improvements can be initiated at any stage, but it is our assertion that drilling accuracy is a practical anchor in any operating mine or quarry for a structured continuous improvement process. This paper will: 1. Define deviations from plan and provide some best practices for maintaining drilling accuracy. 2. Introduce tools and methods to monitor and calculate consequences of accurate versus inaccurate drilling. 3. Demonstrate the use of these tools and methods and their impact on one cost item, the mitigation of oversized material by a hydraulic hammer. 4. Provide recommendations for implementing improvements.

Feb 1, 2023

By H. Fayed

Froth flotation technology is the backbone of the minerals pro-cessing industry where minerals are concentrated by selective separa-tion; either direct or in-direct flotation. In direct flotation useful minerals are conditioned to become hydrophobic (water-repellant) and attach to air bubbles while impurities (non-useful particles) remain in water. The hydrophobic particles are transported by air-bubbles to the top froth (foam) layer in flotation tank which can be removed as a concentrate. There are many factors that controls this selective separation process such as: particle’s degree of hydrophobicity, size, mass loading, air holdup and bubble size distribution. Turbulent fluctuation of the slurry in the tank is another important factor that controls the collisions rate between particles and bubbles and hence attachment rates. The turbu-lent fluctuations are measured by the local distribution of turbulent dissipation rates. Conventional flotation machines are restrained by residence time of the slurry that is about 3-5 minutes that results in a large footprint and limits the capacity of flotation plants. The designers of conventional flotation machines try to reduce the footprint of flota-tion tank by scaling up the flotation machines to increase plant throughput. The scale-up process reduces the specif power consump-tion and the local distribution of shear rates and turbulence dissipation rates. This scale-up results in a larger mean bubble size and lower particle-bubble attachment rates.

Feb 1, 2023

By E. Watkins, S. J. SCHATZEL, K M. AJAYI, V. Gangrade, Z. Khademian

A stochastic discrete fracture network (DFN) model is developed based on mine site core log data to predict the horizontal and vertical permeabilities from the surface to the top of the caved zone at a longwall mining site in southwestern Pennsylvania. One hundred DFN realizations were generated to determine permeabilities for the isolated zone over an abutment pillar after mining the second panel. The results from this study show that the vertical and horizontal permeabilities from the DFN model agree closely with field measurements, which indicates that the resultant permeability obtained from the field measurements is representative of the predicted permeabilities. With this agreement, the aperture data for other zones of the mine could be obtained from the geomechanical model — specifically, for the fractured zone over the gob. Based on the successful validation of this model, this model could be further developed to predict the permeability of the fractured zone over the gob with fracture aperture obtained from the geomechanical analysis. This will complete the fracture characterization of the overburden, which could be used to predict potential shale gas flow to the mine in the event of a breach. This prediction could provide information on the associated risk of a casing breach and determination of methods to proactively prevent such an occurrence.

Feb 1, 2023

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

By N. Theron, R. F. Meeser

The global emphasis on conserving energy resources has led to the adoption of hybrid power systems in vehicles. Optimally applied, hybrid systems can save up to 40% on fuel costs. To optimally manage a hybrid vehicle's energy flow it is necessary to know, in real time, all the energy requirements to complete a given route. The energy consumption depends mainly on the vehicle mass, speed profile, and route topography. Of these, the topographic profile is the one factor that is only route-dependent and not influenced by the vehicle or driving styles. The heading vs. distance profile is also an example of a route characteristic not influenced by the vehicle or driving style. In this study the topographic and heading profiles are used to identify routes, and are easily measured by means of digital barometric pressure and compass sensors. Correlations between the current route and previously travelled/stored routes are performed based on their topographic and heading profiles in a point-by-point manner. Above-ground tests were first performed using a road vehicle and six routes to evaluate the system. The system consistently and correctly identified a 20 km route within the first 4 km. It also proved to function correctly in underground tests through the implementation of an instrumented hand-held surveyor's wheel. This system finds direct practical application in optimizing the energy management of an underground hybrid locomotive used by the mining industry in South Africa, but can also be of benefit in applications where route identification is required and using GPS is not feasible.

Jan 26, 2023

By N. P. Mabasa, N. Naudé, A. M. Garbers-Craig

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling MgO-C and Al2O3-MgO-C refractory bricks, which are widely used in the steelmaking industry. Since approximately 28 Mt of refractory bricks are discarded each year, it is logical to recycle them. When furnaces and ladles are relined, the spent refractory bricks become mixed up, and need to be sorted before recycling. This study examined the use of a hand-held X-ray fluorescence analyser (HH-XRF) to distinguish between spent oxide-based and oxide-carbon-based refractory materials, with special emphasis on spent MgO-C (MC) and Al2O3-MgO-C (AMC) bricks. HH-XRF analysis was conducted on 18 oxide-carbon refractory bricks as well as on MgO-chromite and bauxite-based refractories. X-ray diffraction, reflected light optical microscopy, and scanning electron microscopy with energy dispersive spectroscopy were used to characterize the MgO-C and Al2O3-MgO-C bricks to confirm the accuracy of the HH-XRF analyses. This study also underlined the importance of calibrating the HH-XRF analyser for the refractory bricks to be sorted. The HH-XRF was successful in distinguishing between the different oxide-carbon-based refractory bricks both before and after cleaning. This result is important as it proves that HH-XRF provides a method whereby spent MC and AMC bricks can be sorted quickly and reliably.

Jan 26, 2023

By Y. Yang, L. Li, X. Liu

Coal mining in China is facing the transition from output to quality. Based on the total mining capacity and average production, the current situation of coal mining at mine, city, and province levels is analysed, and data in support for the layout of sustainable mining development and the optimization of output provided. The results show that 87% of China's coal is mined by underground methods, with an average production capacity of 0.93 Mt/a per mine. Open pit mining accounts for 13%, with an average mine production capacity of 5.73 Mt/a. The average mining capacity of coal mines in China is 1.05 Mt/a, with 1181 coal mines with an average capacity less than 0.3 Mt/a, accounting for 35% of the total coal mines but contributing only 4.51% to output. They are distributed in about 48 cities in six provinces, seriously restricting the transition to green coal mining. The coal industry should speed up the closure of small coal mines in key provinces and cities, eliminate outdated production capacity in the central region, increase the speed and proportion of coal resources moving westward, and promote high-quality development of coal mining.

Jan 26, 2023

By A. Mabentsela

A furnace freeze lining is necessary for safety and economic reasons in several smelting operations. The integrity of the freeze lining is put at risk by furnace power imbalances. Although numerous models have been derived to model the growth and depletion of the freeze lining due to power imbalances, no model exists for thermomechanical damage to the freeze lining. This study provides an initial pathway for modelling thermomechanical damage to the freeze lining in an ilmenite smelting furnace using information from the literature and experimental work. A methodology under the framework of continuum damage mechanics is proposed to model mechanical damage to the freeze lining due to phase changes, thermophysical changes, and constrained thermal expansion. Drill cores of solidified slag ingots were used to represent the freeze lining. The modified power law proved to be the best predictor of the softening response of the drill cores. Damage driving parameters were extracted from the raw data, and governing equations of the parameters with respect to temperature were derived for use in a finite element method (FEM) code.

Jan 26, 2023

By Ping Zhang, Xu Ma

Perturbations arising from mining operations significantly affect the stability of rock masses, and the influences aggerates with the rapid increase of mining-operation depths during recent years. The subsurface structures with major discontinuities subject to seismic hazards resulted from the shear-slip behaviors of rock masses. In order to identify the shear-slip regime of discontinuities and calculate seismic moment and seismic energy involved with shear-slip behaviors, we use discrete element modeling to study the shear slip failure along discontinuities in an underground mine. The recorded characteristic and properties of sub-contacts in DEM provide a basis for computing and visualizing the temporal and spatial distribution of seismic moment and seismic energy with mining operations. We computed the seismic energy and seismic moment using the numerical modeling method and the analytic method. We compared the result of summing seismic energy and seismic moment from the subcontacts of numerical models and the result of the analytic method. We confirmed that this tool can be used in comparative analyses. We also found that seismic moment and seismic energy, associated with shear stress drop and shear displacement increase, accumulate in the vicinity of major discontinuities. Mining operations at a greater depth cause greater changes of seismic moment and seismic energy, leading to a higher risk of inducing seismic hazards. Quantifying seismic potential using discrete element modeling can greatly facilitate the investigation of instability of geological discontinuities and thereby can help estimate the potential of seismic hazards.

Jan 21, 2023

By Nawal Kishore, Nilesh Pratap Singh, Amit Kumar Verma, Vikram Seervi

In India, demand for coal exceeds its countrywide supply, despite its natural abundance, due to failure to achieve high production targets, especially in opencast mines, which are responsible for 94.98% of total raw coal production within the country. Employment of technological solutions, such as surface miners, is key to achieving higher coal production and productivity in an eco-friendly manner, especially in the populated areas adjacent to the mining zone and, hence, require restricted blasting operations. It eliminates blast hole drilling, blasting, and primary crushing units, thus reducing related environmental hazards like ground vibration and fly rocks. This paper encompasses the applicability, advantages, constructional features, and performance assessment models for each working mode of a surface miner. The current paper discusses the correlation between coal production and key productivity indicators, namely, machine shift-time, pick, and diesel consumption of surface miner in three different geo-mining conditions. Furthermore, relationships between machine shift-time, pick, and diesel consumption of surface miner and coal production were evaluated through bivariate regression analyses along with their coefficient of determination. These key productivity indicators of surface miner follow polynomial relationships with coal production on a daily and monthly basis, having Pearson correlation values from 0.774 to 0.907 and coefficient of determination, from 0.664 to 0.909 in opencast coal mines.

Jan 20, 2023

By I. WILKOMIRSKY, J. BECKER, F. Parada

CORRECTION

Jan 18, 2023

By Jian Wang, Kun Li, Hao Wu, Juan Nan

In this paper, in order to solve the problems of low accuracy and slow speed of fire flame recognition, an extreme learning machine (ELM) method based on improved Harris hawks optimization (IHHO) is proposed for fire flame recognition. A novel Harris hawks optimization (HHO) is used to solve the problem of parameter selection of ELM. In order to solve the problem that the original HHO is prone to fall into local optimum, firstly circle mapping is used to initialize the population to solve the problem of uneven distribution and small range of the initial population. Then the formula of escaping energy of HHO is modified to make the population have a large range in the middle and late iterations while gradually decreasing in the whole iteration process. Thus, the exploitation stage in HHO is improved to make the search range smaller near the optimal solution to accelerate the convergence process. Finally, at the end of each iteration, a certain number of individuals are selected to perform Gaussian and Cauchy hybrid mutation to prevent the IHHO from falling into local optimization. Through three groups of experiments, the effectiveness of the proposed IHHO and IHHO-ELM is verified. In experiment 1, the convergence performance of IHHO is significantly better than that of the other remaining algorithms in the test results of six benchmark functions. In experiments 2 and 3 of real fire flame recognition case, IHHO-ELM outperforms other remaining algorithms on the whole and has significant advantages in some indexes.

Jan 17, 2023

By Suprakash Gupta, Pawan Kumar Yadav, Deepak Kumar, Debasis Jana

Draglines are extensively used in Indian mines. A dragline has more than hundreds of components, and it is complex in design. This study involves the evaluation of the reliability of a draglines system using a Bayesian network (BN) model mapped from a fault tree. Based on the BN inference, the reliability estimation, the diagnosis, and the sensitivity analysis are performed. In this paper, the overall reliability of the dragline is estimated as well as the contribution of the subsystems or components in the overall reliability evaluation is presented. The results showed that the three subsystems of the dragline, namely, the dragging mechanism, electrical auxiliary subsystem, and swing mechanism, have the lowest reliability (82.17%, 87.98%, and 91.30%, respectively) after an hour of operation. The overall reliability at the first hour of machine operation is estimated to be 62.03%. The study may provide a reference for future work related to the dragline machine’s reliability design and maintenance.

Jan 14, 2023