Search Documents

By C. H. Bucknam

Metallurgical processing of gold ores in positive water balance environments has been facing decreasing discharge concentrations in permits and additional requirements to pass acute toxicity testing before discharges will be allowed to native fisheries. In response to the challenge to meet 0.005 mg/L free cyanide guidance for discharges to fresh water fisheries, the American Society of Testing and Materials (ASTM) International Cyanide Task Group has undertaken an interlaboratory study for the free cyanide method in the metallurgical processing cyanide detoxified reverse osmosis effluent to determine if the quantitation limit for the method could be lowered from the current 0.009 mg/L free cyanide (1) to less than the 0.005 mg/L guidance concentration. Results of the testing are presented below.

Jan 1, 2012

A typical sub-level block cave mining extraction method employs an undercut level to establish a cavity in hard rock, and as such requires special support methods and products to be installed during the development phase. The undercut level development in the block cave orebody is then sacrificial, and support elements will eventually report to the crusher and perhaps conveyor belt systems for transportation to surface. The choice of support products installed in the undercut level development should take cognizance of the detrimental effect these could have on the mining system such as cutting of conveyor belts, obstructing crushers, safety aspects, and productivity. This work explores the probability and practicality of making use of new-generation support products to make the operation safer as well as enhance productivity in the development phase and during the undercut operation. This paper will investigate the use of glass reinforced plastic(GRP) rockbolts and GRP mesh instead of conventional steel bolts and mesh along with resin capsule-filled holes with the GRP bolts. Complementing this with thin spray liner (TSL) application as another means of creating a safer operating environment, as well as a productive support medium, will also be addressed. These proposed items are envisaged to reduce production downtime and improve the safety of our people. These items are all easy and light to handle, cuttable and crusher friendly, as they will break up during the crushing process.

Jan 1, 2012

By Jing Zhang, Chenguang Bai, Fusheng Pan

"The microstructure and hot deformation behaviour of an Er-modified Mg-Zn-Ai alloy were evaluated. The results showed that the addition of rare-earth Er changed the morphology of the quasi-continuous grain boundary networked eutectic compound to globular particles. Moreover, a self-strengthening effect was identified for the alloy, which determined its deformation behavior. After hot extrusion, the yield strength and elongation to failure of the Mg-Zn-AI-Re alloy at 200°C were increased by 105% and 120%, respectively, due to an emerged dynamic precipitation strengthening mechanism.IntroductionMagnesium alloys are attracting increasing attention for applications in automobile, electronic devices and hand tools for weight reduction and higher fuel efficiency, because of their lightweight and a high specific strength. However, application of Mg is still very limited. The largest applications are still those non load-bearing castings used at room temperature, such as box case, housing, and covering. One of the main reasons is the inadequate absolute strength both at room temperature and elevated temperatures (> 100°C) of the commercially used AZ, AM series alloys, due to the incoherent interface between the secondary phase y-Mg17AI12 and Mg matrix, as well as the low thermal-stability of the y phase [1]. Besides, the heat-resistant magnesium alloys which contain rare earth (Re) as the main alloying element are very expensive. The other reason is their poor deformability. The key solution is therefore to develop low-cost heat -resistant wrought alloys."

Jan 1, 2012

By Michael Karmis, Syed Muhammad Tariq, Zeshan Hyder

Secondary or boulders blasting is a regular feature of quarrying operations in Pakistan, especially in cement and stone crushing industries. The main reason for secondary blasting is the production of a large number of boulders during the production blast. These boulders are larger than the feed hopper of crushers and require further breaking. The complex geometry of boulders, relative lack of restraining burdens, and the availability of number of free faces make this kind of blasting more hazardous than production blasting. Secondary blasts have generally unpredictable results and may cause flyrock, airblast, and over-crushing of rock material. Thus, it is essential to have an appropriate amount of explosive charge/powder factor, and for it to be properly distributed in the blast hole. The greater the amount of explosive over the required amount, the more violent is the blast, which will result in more flyrock, airblast, and excessive crushing of boulders.

Jan 1, 2012

By G. J. Joy

Although rates of pneumoconiosis in coal miners have declined substantially in the United States since the passage of the Federal Coal Mine Health and Safety Act of 1969, new cases continue to occur, including cases of rapidly progressive disease. In contrast, Australia's underground coal mining industry has reported few new cases of pneumoconiosis for more than 20 years. Mortality from coal workers' pneumoconiosis in official health statistics and the prevalence of pneumoconiosis among miners screened in X-ray surveillance programs are also lower in Australia. The U.S. National Institute for Occupational Safety and Health (NIOSH) was requested by both industry and labor stakeholders to examine this issue, with the ultimate aim of reducing the rate of pneumoconiosis among U.S. coal miners. A number of factors, including coal dust exposure, silica exposure and coal rank were examined as potential contributors to the above noted differences. Comparison of coal rank data from each country did not illuminate the issue. Air sample data from the coal mining industries in both countries show that coal dust levels in Australian mines are somewhat higher than those reported in similar U.S. mines; however, quartz exposure for Australian miners is lower than for many U.S. miners. If quartz is contributing to the greater number of cases of pneumoconiosis in the United States, more effective dust control measures, as well as an independent exposure standard for respirable quartz in coal mining, should be implemented to reduce this potentially disabling condition.

Jan 1, 2012

By Riyad N. Ahmad-Bita, Shadia J. Ikhmayies

"SnO2:F/CdS:In structures were prepared by the spray pyrolysis technique on glass substrates at a substrate temperature Ts = 450°C. NH4F and HF were both tried as the sources of fluorine in the precursor solution of SnO2:F. A comparison between the properties of structures obtained by using the two doping compounds was performed. X-ray diffraction (XRD), scanning electron microscopy (SEM) and transmittance measurements were used to characterize the films. The structures prepared by using HF as a fluorine source were found to have more ordered crystal growth, larger grain size and sharper absorption edge. From the inspection of the first derivative of the absorbance it is expected that more interdiffusion on the SnO2:F/CdS:In interface takes place in the structures made by using HF. These results confirm that these films are better as forecontacts for CdS/CdTe solar cells.IntroductionThin film CdS/CdTe solar cells built in the superstrate geometry rely on transparent conducting oxides (TCOs) to make the front contact The investigation of combined CdS-TCO films has recently been developed owing to the great interest of better understanding the effect of these bilayers on the absorbers [1]. Usually SnO2 is utilized as a front contact for these solar cells. Optimizing the properties of the SnO2/CdS structures is an important step on the way to get high performance CdS/CdTe solar cells.There are different methods to prepare SnOz thin films, such as reactive sputtering [2], evaporation [3], chemical vapour deposition [3, 4], dip coating [5] and spray pyrolysis [6-9]. At the same time CdS thin films can be prepared by different techniques such as chemical bath deposition [10], thermal evaporation [11], screen printing [12] and spray pyrolysis [7, 13]. However, the spray pyrolysis technique is a very low cost and simple technique that enables intentional doping and getting large area and uniform thin films [14]. For these reasons it is choused to prepare SnOz and CdS thin films in this work. To improve the properties of these compound semiconductors, SnOz was doped with fluorine and CdS was doped with indium where such doping is well known for these compounds."

Jan 1, 2012

By John Ellenberger

The nature of a stone deposit is rarely defined through exploration and engineering design, but more through the actual experience encountered as the mine develops; hence, issues with ground control are often at the forefront for a new mine. Ground control problems account for over 15 percent of lost-time injuries in underground stone mines. The objective of this work is to present actions taken during early development of a stone mine to mitigate the obvious effects of high horizontal stress on ground control. The mine was developed from a box cut with relatively little cover, and high horizontal stresses were not anticipated. Early recognition of possible high horizontal stress resulted in mapping of the mine using the NIOSH-developed Roof Fall Risk Index (RFRI) to provide a baseline to objectively analyze roof conditions. A program of borescoping the mine roof provided valuable roof beam thickness data and found that the roof beam was of minimal thickness, approximately 10 percent of drift width. As the mine developed, it became apparent that ground control problems related to high horizontal stress existed. A concentrated effort was made to improve ground conditions by implemeting a number of mitigation techniques. Actions taken by the mine included systematic roof support, reorientation of mining direction, a lower roof horizon, reduced span widths and reduced mining height in crosscuts to prevent running falls. These strategies resulted in signifcantly improved ground stability.

Jan 1, 2012

The propensity of coal spontaneous combustion can be evaluated using various laboratory testing methods such as R70 adiabatic tests, thermal gravimetric analyzer (TGA) and critical self-heating temperature (CSHT) methods. Each of the methods has its unique characteristics and index for classifying the propensity of self-ignition of coals. Accountable relationships among the propensity indices of different methods should be established. Using the newly established R and TGA testing setups in our ventilation laboratory, samples from US coal mines have been collected and tested. 70 The TGA is a relatively new quantitative method. A test can be conducted in a relatively short time. The temperature and weight of the sample can be measured with high precision and then used to determine the activation energy of the coal which is a good indicator for potential of self-heating. Under a specific experimental design, the TGA technique could perform the proximate analysis for determining coal quality parameters (e.g., moisture, volatile matter, fixed carbon and ash content). These parameters can be used in an empirical equation for assessing the potential of coal self-ignition. The trend of activation energies determined using TGA techniques and adiabatic tests are reasonably consistent with each other. As a case study, a comparative analysis of these two methods for determining activation energy was made on coal samples collected from Indiana. The kinetics of the spontaneous combustion mechanism has been explained. If the functional groups of a coal are easier to be activated with a small amount of activation energy at a relatively low temperature, the coal will has a higher potential of self-heating. With the kinetic and coal quality parameters determined by the TGA setup, it has been found that the coal with low potential of self-ignition has low self-heating rate, high activation energy and high minimum self-heating temperature.

Jan 1, 2012

By S. Koski

The Cerro Verde copper-molybdenum porphyry mine, majority owned and operated by Freeport- McMoRan Copper & Gold, is located 30 km southwest of Arequipa Peru. The concentrator, which produces copper and molybdenum concentrates, started operating in late 2006 with a 108,000 tpd design capacity, processing primary sulfide ore (mainly chalcopyrite and molybdenite). Plant capacity was recently increased to 120,000 tpd. The comminution circuit consists of one 60? x 113" primary crusher, four MP-1000 secondary crushers in closed circuit with dry screens, four 2.4m x 1.6m High Pressure Grinding Rolls (HPGRs) in closed circuit with wet screens, and four 7.3m x 11m gearless ball mills in closed circuit with cyclones. The HPGR circuit is fed by the Secondary Crushing circuit product at a T80 of 35 millimeters, and the HPGR circuit product feeds the Ball Mill circuit at a T80 of 3000 microns. This paper describes operating experiences with HPGRs during these first four years highlighting improvements in operating practices and presentation of data regarding operational efficiencies, also discussed are the primary benefits provided by HPGRs such as production of micro fractured particles, reduced ore Bond Work Index, and reduced power consumption. Cerro Verde represents the first installation of HPGRs in both the copper industry and large scale hard rock mining.

Jan 1, 2012

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By Fan Xiao-Hui, Jiang Li-Juan, Chen Xu-Ling

"In order to solve air leakage of sintering testing cumbersome, inaccurate results, and other issues, the sinter machine air leakage characteristics were studied, and combining the mathematical modeling and the field detection. The temperature before air leakage was calculated by mathematical model, energy balance equation was established according to sintering process, using Adams prediction correction method which has stronge stability and high precision, to solve hyperbolic partial differential equation with astringency problem. The temperature after air leakage is detected by instruments, according to energy conservation calculation the sintering air leakage rate. According to the sintering continuity and periodicity, sintering air leakage location diagnosis expert system was established to judge specific air leakage locations.IntroductionStrengthening of modern blast furnace production depends on the quality of the raw material preparation to a large extent [1]. Technical and economic index of modern blast furnace production is advanced; the most important reason is the use of concentrated feed. Sintering plant is the ""kitchen"" of blast furnace’s concentrate. As we all know, sintering plant is major energy consumption of steel plant, in sinter process energy consumption, the solid fuel consumption of total energy consumption is 75%~80%, power is 13%~20%, ignition and combustion is 5%~10%. To reduce the air leakage of sintering plant is an effective measurement to save energy consumption. At present, our air leakage of sintering compared to the other developed countries is still a long way to go. Japan’s air leakage rate is about 30%, and 35%~60% air leakage of sintering machine at home, a big gap exists between the plants. At present the determination of air leakage is all for manual operation, long measuring period, considerable manpower and resources, and the results are significantly affected by operation. For air leakage of sintering control lag issues, research and development of diagnosis expert system for on-line monitoring model for air leakage and, through this research can reduce the use of detection equipment, detect sintering air leakage, improve the yield and quality of sintering production, reduce energy consumption, and extend equipment life span."

Jan 1, 2012

By W. Burger

Mechanical excavation methods can significantly improve excavation performance and labor safety compared to drill and blast operations. Herrenknecht has developed a mechanized shaft sinking method for soft and medium strength rock. This system combines innovative technologies which allow simultaneous excavation, removal of cut material and the installation of rock support. This Shaft Boring Roadheader ?SBR? is flexible in diameter and can be used in shafts with changing diameters and different shaft support requirements for depth up to 2,000 m. During regular excavation personnel are not required to access or work on the shaft bench. The boom used to cut the shaft profile is based on roadheader technology.

Jan 1, 2012

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By G. A. Bezuidenhout

Lonmin Platinum installed a concentrated mode dual-alkali scrubber at the smelter in Marikana in 2002. The dual-alkali scrubber was the technology of choice at that time as a sulphur fixation plant, due to the perceived benefits of handling both the high SO2 concentrations of converter off-gas and the swings in SO2 concentration that are linked to Peirce-Smith operation. Owing to current and impending legislative requirements for air quality and waste, Lonmin is currently considering additions to the dual-alkali plant, but is also evaluating alternative technologies for sulphur fixation. This paper reviews the decision of Lonmin to install a concentrated mode dual-alkali scrubber and presents plant performance achieved. It also describes the important control variables and sensitivities of the plant, and the final product that is produced by the operation of the plant. The legislative requirement that drives the Lonmin technology evaluation is also discussed.

Jan 1, 2012

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

Despite the claims of energy efficiency and the considerable development that has gone into dramatically extending rolls? life and facilitating rolls? change-out, in the six years since the last SAG conference, only a few HPGR operations have entered the realm of mineral processing. Risk barriers to the take-up of new equipment or processes are: a massive increase in materials handling issues as well as in the number of pieces of equipment required, low total circuit potential energy savings, and similar or higher capital costs. An alternative route is to make use of the complementary strengths of the HPGR and SAG in hybrid circuits. Minimising materials handling issues, providing an ideal balanced feed to the AG or SAG mill, and improving controllability through shifting grinding load as the RoM feed changes, are all potential major advantages to this approach. Conceptual circuit layouts, based on real measured ore and equipment data, are presented here to illustrate the potential production upside, the reduction in operating costs and the reduction in the physical and energy footprints.

Jan 1, 2012

As mine haulage vehicles become larger, the danger to a driver during a fire emergency is increased by the greater height of the cab above ground. Also, property damage due to fires on bigger trucks can be substantial. To solve this problem, the Department of Interior's Bureau of Mines, through two research and development contracts with FMC Corporation, San Jose, California, has developed two reasonably priced, reliable automatic fire sensing and suppression prototype systems for large haulage vehicles. At the onset of the large mobile equipment fire protection contract effort, it was learned that fires were frequently experienced in open-pit mine haulage equipment, especially large trucks. As the size of equipment has grown, so has the hazard presented to an operator forced to leave his truck in a hurry when fire breaks out and his normal path to the ground is blocked by flames. His only recourse is to jump from the cab platform to the ground, and the one-story drop of 10 feet or more can severely injure him. It is with these factors in mind that a program was undertaken to provide a fire detection and extinguishing capability tor the large mobile equipment, especially trucks, used in open pit mines.

Jan 1, 2012

By Neil E. Izatt, Ronald L. Bruening, Steven R. Izatt

"IBC has developed environmentally friendly Molecular Recognition Technology (MRT) processes to selectively extract, recover, and purify a wide range of metals from a variety of process streams. The incorporation of MRT into process flow sheets can improve the economics of the processes. MRT separations are effective even at low (mg/L to \i%JV) metal levels. MRT processes are sustainable, being economically viable, energy efficient, and environmentally friendly as well as having a low carbon footprint. Examples of MRT processes will be presented and discussed involving platinum group metals, gold, rhenium, and other metals of interest to the mining community.IntroductionA significant portion of the earth's precious metal resources has been moved during the past century from underground to above ground [1]. This movement has important economic, health, environmental, ecological, and sustainability implications for the earth and its population. There is concern that recycling of certain precious and specialty metals from end-of-life (EOL) electronic wastes (e-wastes), catalyst wastes, mining waste streams, and other waste products such as rechargeable batteries is not adequate to maintain supplies of these metals sufficient for future needs [2-4]. Improved metal recycling rates and more efficient metal recovery from the enumerated wastes would significantly reduce the amount of virgin metals that must be mined to support our lifestyle [5]. More efficient separation procedures in ore processing flow sheets and more effective recovery of metals from low-grade waste streams would reduce metal loss in the mining industry."

Jan 1, 2012

By Xiang Sun, Zheng Zhang, Jiann-Yang Hwang, Zhiwei Peng

"Nickel oxide nanoparticles were synthesized using sodium dodecyl sulfate as the surfactant and urea as the hydrolyzing agent and different calcination temperatures and time were selected for preparation. Nitrogen adsorption (BET), X-ray diffraction (XRD) and scanning electron microscope (SEM) were subsequently used to characterize the prepared samples. The effect of an external electric field on hydrogen adsorption over a prepared nickel oxide was carried out. The electric filed was introduced by a piezoelectric element, which is capable of autogenously generating charges under hydrogen pressure. Increased hydrogen adsorption was obtained from this study, which indicated a stronger interaction between the adsorbent surface and hydrogen.IntroductionMetal oxide has attracted great attention for adsorption because of their wide application in catalysis [1-7], gas storage [8,9] and sensors [10,11]. However, with respect to the usage in hydrogen adsorption, few research outcomes have been reported [12,13], since there remains the difficult task of synthesizing highly porous metal oxides with unsaturated metal centers, which account for the strong interaction with hydrogen [14,15]. Nickel oxides are polar materials with an intrinsic dipole moment. The external applied electric field could further enhance the dipole moment so that the hydrogen could be more strongly adsorbed."

Jan 1, 2012

By P. Condori

Palabora Mining Copper (PMC) has two autogenous mills that have been in operation since 1976. The mills were originally designed to treat 30 000 t/d of open cast copper ore in a closed circuit with cyclones. As the ore body went deeper the open cast method of mining was changed to block caving, a consequence of this was the dolerite content (hardest barren material) increased significantly, increasing the production rate of pebbles and thus reducing the milling capacity. In order to cope with the increased ore hardness and to increase mill capacity, a second ball milling stage and pebble crushing were incorporated to the circuit. The above actions created new challenges to the circuit operation and bottlenecks in different areas of the milling circuit. This paper reports the holistic work performed on the Palabora autogenous milling circuit including the implementation of a mill constraint control scheme, the implementation of a pebble removal system from the circuit and a new circuit configuration. The achieved plant stability and increment of ore throughput are also reported in this paper.

Jan 1, 2012