Search Documents

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By Philip Nash, Jie Zhou, Joshua Blackketter

"Large ingots tend to have internal defects such as shrinkage cavities and porosities, which have to be closed during the cogging stage to ensure sound internal quality of forged parts. In this work, finite element methods were used to simulate open die forging passes, with varying parameters that affect the void closure behavior profoundly. Numerical models ware constructed in ABAQUS, DEFORM and FORGE using data taken from footage of the forging process and material mechanical data obtained from the Gleeble compression tests. Forging variables such as pass rotation, reduction per pass, and feed ratio were studied with intense attention paid on the special properties of H13 steel, so that this study can be applied to solve real world problem.IntroductionCenterline defect closure is a frequently studied but still challenging topic in open die forging industry. In practice, open die forging is employed as an effective hot forming process to make desired shape of metal products as well as to ensure center consolidation of internal defects which result from the casting process. Nowadays, remarkable large forgings have been more and more required to meet industries demand. However, the increase in ingot size has tended to result in considerable macrosegregations and shrinkage cavities or voids, which need to be worked thoroughly during the forging process; but the size of the products and limitations of manufacturing capacity, such as the press load, make it difficult to achieve adequate local deformation to close those defects. Therefore, choosing optimal forging parameters under given work condition to ensure good internal quality of forged products is critically important."

Jan 1, 2012

By H. Wilhelm, W. I. van Drunick

The Anglogold Ashanti (AGA) Navachab single stage SAG mill has provided an excellent setting for incremental optimization. Over the past decades, several interventions have resulted in marked improvements in specific performance; including steel ball scat removal, re-design of the mill lifters, replacement the pebble crusher and cyclone cluster, as well as the use of a vibrating screen in place of a discharge trommel. Recent initiatives now include an operating fine DMS circuit, studies on pre-crushing of the ROM feed and also fine-screening as an alternative to hydrocyclone classification. The current optimized state of the Navachab mill allows it to operate at approximately 20% higher efficiency when compared to mills of similar shell dimensions in gold mining, treating similar ore. This paper describes the systematic improvement of the SAG circuit to its current state.

Jan 1, 2012

"The QEMSCAN system is the third generation of automated mineral analysis systems that began with the QEM*SEM at CSIRO 30 years ago (Butcher et al. 2000). It is now a successful commercial instrument with 39 instruments in operation around the world. Back Scattered Electrons (BSE) and Energy Dispersive (EDS) X-Ray spectra are used to create digital mineral images with mineral identification occurring online. Low-count EDS spectra are used preferentially to BSE brightness, allowing minerals to be accurately identified by chemical composition. Individual minerals or groups of similar compositions are identified by comparison to a comprehensive mineral database incorporated into the QEMSCAN software. Optical mineralogy and Scanning Electron Microscopy is a metallurgists’ tool for determining the ore process mineralogy and delivering a better flowsheet. These techniques have limitations, provide limited information and sometimes fail to provide representative information. In contrast, QEMSCAN provides information on the nature and occurrence of all mineral species present plus the liberation characteristics, looking at thousands of particles in the sample presented. Some of the data presented includes:• Particle and grain sizes• Dominant mineral species• Particle shape• Calculated metal content• Density• Deportment of elements of interest between the mineral phases• Quantitative mineralogy• Mineral associations, locking and liberation• Textural relationships (particle images)It can also be used on concentrates, polished sections or drill core. This is a significant improvement in ore characterisation providing lithology, mineralogy, liberation, ore grade and porosity from a sample. Theoretical grade-recovery curves can be created to be mineralogically limited from QEMSCAN analysis which, when compared with metallurgical results, are valuable in evaluating whether liberation or chemical selectivity is driving flotation performance. A number of case study examples are given where the QEMSCAN had a significant bearing on future project development at an early stage of exploration and mine development."

Jan 1, 2012

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

By C. Zografidis, K. Karalis, E. Devlin, S. Tabouris

"The main parameters affecting energy and electrode consumption in smelting reduction of Greek nickeliferous laterites in submerged arc electric furnaces (E/F) were investigated. Within this framework, the operational data of E/Fs, such as energy consumption indicators, electrode consumption indicators and chemical characteristics of Fe-Ni and slag, were correlated with the physicochemical characteristics of the calcine, produced by roasting reduction of laterite in rotary kilns (R/Ks), such as reduction degree, temperature, chemical composition and granulometry. The results obtained provide a significant input for further research on the modelling of the roasting reduction – smelting reduction process, which is a critical tool for energy optimization.IntroductionThe two main steps of pyrometallurgical treatment of greek nickeliferous laterites for ferronickel production include: i) drying, pre-heating and controlled pre–reduction of laterite ores with solid fuel reducing agents and fuel oil in rotary kilns (R/Ks) for the production of a calcine, and ii) smelting reduction of the calcine in open-bath submerged-arc electric furnaces (E/Fs) for the production of Fe-Ni alloy with 12-16% Ni [1].The energy absorbed from the endothermic reductive reactions of iron, nickel and cobalt oxides (Fe2O3, FeO, NiO and CoO) of the calcine with the remaining carbon in the E/Fs, corresponds to about 16% of the total energy output in the smelting reduction step [1]. This is indicative of the significance of the calcine’s reduction degree for the electric energy requirements in the E/Fs. Moreover, the chemical characteristics and the granulometry of the calcine constitute critical parameters for the energy requirements as well as the smooth operation of the E/Fs."

Jan 1, 2012

By M. K. Patel, K. A. Pericleous, M. Molaei

"The future trading of carbon credits and increased financial cost necessitates substantial cuts in incidental C02 emissions in the production of metals (iron, steel, aluminum, zinc, lead). Although greener methods of production are being developed, in the short term the use of point-source C02 extraction using existing technology remains attractive. Accelerated natural carbonation, in a fluidized bed is a feasible technological route investigated in this research. CFD modelling has been used to study the efficiency of C02 capture in a fluidized bed reactor containing a CaO solid sorbent. A Lagrangian/Eulerian scheme describes describe CaO particle trajectories and exchange of mass, momentum and energy with the carrier gas, with a typical off-gas composition. Different reactor geometries are considered (with uniform, stepped and gradually expanding cross-section), to maximize conversion for a given particle loading and size distribution (100-200 microns). Removal efficiencies of up to 80% are demonstrated, making this a viable process.IntroductionBased on Intergovernmental Panel on Climate Change (IPCC) reports, the major cause of climate change and global warming is due to a high level of C02 concentration in the atmosphere resulting from fossil fuel combustion, particularly in coal-fired power plants [1]. Carbon capture and storage is therefore the most important action proposed to reduce C02 from combustion flue gases. In this process, carbon dioxide is captured and may then be regenerated as pure C02 and conducted to a permanent storage, or simply stored as a solid carbonate [2]. Capture and storage of C02 has an economic penalty and the main cost of this penalty is associated with the capture plant. Capturing C02 with a lime-based solid sorbent (CaO) is a very promising technique, due to the low cost and the wide availability of the reactant. In this process, the CaO reacts with C02 based on the following reaction in a reactor called a Carbonator:"

Jan 1, 2012

By Navid Hosseini

Several empirical equations to estimate coal pillar strength have been presented in academic studies. The development processes of these equations are similar and are usually obtained by fitting the mathematical function (curve) to field data. One of the best criteria to evaluate the quality of fitting for such equations is the correlation coefficient R2, which has limited applicability. It is necessary to calculate the correlation coefficient access to the initial data for which the equation is presented; this is impossible for many coal pillar strength formulas. This paper presents a new approach based on the analysis of uncertainty amplitude to compare the coal pillar strength. This approach utilizes a combination of parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), function type and degrees of freedom. The confidence level of constants is subsequently formed and the correlation coefficient becomes more comprehensive. Therefore, for an effective comparison, the efficiency and accuracy of coal pillar strength formula can be used. Keywords: Coal Pillar Strength, Correlation Coefficient, MATLAB, Uncertainty Criterion

Jan 1, 2012

By K. Short

Over the past several years, the mining and minerals market was overloaded with discussions around reviving mature terminologies like distributed control systems (DCS), programmable logic controllers (PLC), and the ?new comers?: hybrid control systems (HCS) and programmable automation controllers (PAC) and, in parallel, which technologies would be more appropriate for mining and mineral processing applications. Ten years ago, a careful comparative analysis would make more sense. Control approaches had very distinctive differences where users needed to choose the right approach.

Jan 1, 2012

By F. Mielli

Ranging between 20% and 40% of the typical mining operational costs, energy in mining operations is a growing concern for the industry. However, this concern is a complex, multi-faceted variable that involves government regulations, societal pressures, cost and competitiveness. A mining company successful in energy efficiency is becoming the standard of a successful company. The suggested energy strategy in mining and mineral processing operations has to follow a well structured approach that entails the following: ? Understanding where energy is being used and why, ? Recommending and implement energy conservation measures, ? Driving visibility to targets and results, ? Leveraging the energy spend across the enterprise, ? Developing a robust energy and sustainability strategy.

Jan 1, 2012

By Donald Leroux, Asim Tuzun, Simon Gariépy, Luc Lachance, Hayley Halsall-Whitney

"The importance of coherent material balance results has long been recognized by mining and metallurgical companies. Although this is still true nowadays, various stakeholders are increasingly concerned about the origin and the accuracy of the reported numbers. The last decade has shown that most metallurgical accounting concerns can be addressed by making two important changes to plant performance monitoring practices. First, introducing data redundancy into the metal balance procedure allows the estimation of measurement errors. Second, the migration from spreadsheet-based to relational database based systems brings transparency, data integrity, traceability and auditability into metallurgical accounting. Relational databases also facilitate the production of reports that metallurgical accountants must issue routinely. Recognizing the caveats of the spreadsheet-based metal accounting method they had been applying for years, Strathcona decided to switch to a commercial relational database system in 2008. For the most part, the migration was seamless. Some challenges were raised but they could all be overcome and outweighed by benefits gained from day-to-day utilization of the system.INTRODUCTION Metal accounting (Morrison, 2008) has always been essential to high-quality corporate governance of mining and metallurgical companies. Although the importance of coherent material balance results has long been recognized, various stakeholders are increasingly inquisitive about how the reported numbers were obtained and how much accuracy can be attributed to them. This accrued scrutiny is obviously no stranger to the corporate governance tightening that happened through the years in response to outrageous accounting scandals. It is also in continuity with securities laws (such as NI-43-101 in Canada) that were passed to protect the public from other market fraud. Recognizing the importance of spotless metal accounting in their reports to the public, a group of global mining companies gave AMIRA International the mandate of developing a set of rigorous yet practical metal accounting guidelines for the mining and metallurgical industry. The AMIRA P754 project was launched in 2004 and the first version of the resulting Code of Practice was released the following year. Since then, the Code was reviewed twice and revised releases were issued (AMIRA, 2007). While some parts of these guidelines are in continuity with current commonplace practices, other parts recommend changes to inherited practices that may be significant. For example, they highlight the importance of data redundancy (Lachance & Flament, 2011) which in many operations is either already available but unexploited or achievable with reasonable efforts. These guidelines also stress the importance of state-of-the-art metal accounting systems, such as those based on relational databases, which are secure and entirely auditable by a Qualified Person. Because most spreadsheet software packages allow data and formulae to be modified at any time, without a trace and anonymously, they do not meet these requirements."

Jan 1, 2012

By Dakota D. Faulkner

Cable bolts have been very effective in mine ground control. Non-tensioned and tensioned cable bolts are now used for both primary and supplemental bolting (Suder, 2001; Mirabile, 2010). In the United States, cable bolts are typically installed in either 1 or 1-3/8 in. (25 or 35 mm) diameter drill holes and, if point anchored only, are utilized with 4 - 5 equivalent feet (1.2 - 1.5 m) of resin. Cable bolts can be tensioned by various methods such as using an expansion shell mounted on the cable or post-tensioned with a hydraulic cable tensioning unit. In recent years there has been a desire to completely encapsulate the cable bolt for corrosion protection. Fully encapsulating a cable bolt with traditional resins can be very difficult. Keystone Mining Services, LLC (KMS) and Jennmar Corporation have developed a new cable bolt that can be fully encapsulated during installation or post-installation with polyurethane (PUR). The Fully-Grouted Cable Bolt (FGCB)* is equipped with a special head that allows the injection of PUR up through the cable bolt head and cable strands, completely encapsulating the cable and filling the drill hole. Although the FGCB was initially developed to fully encapsulate the cable for corrosion protection, it was also found that by modifying the cable bolt head and injection pressure, PUR could be injected into cracks and fissures of the strata to stabilize the roof. This paper details the development of this system and three underground applications under different ground conditions.

Jan 1, 2012

By van der Meer. F. P.

High Pressure Grinding Roll (?HPGR?) technology is applied in a broadening range of minerals processing applications for relatively wet or moist materials. HPGR grinding of dry material or involving drying and air classification is more common, for example in cement manufacturing. A number of minerals processing plants are also operating with dry material, either due to process reasons, such as considerations of preceding or subsequent process stages, or as dictated by local conditions of arid areas and scarcity of water. The present world-wide expectation of decreasing availability of water supply urges us to look for alternatives that minimize water consumption. Recently established and envisaged future HPGR applications with dry ores have indicated that the technology of dry crushing and classification as practiced in cement and limestone grinding can be applied in minerals processing. Moreover, dry technology could very well be applied for generating a final fine product at sizes near or below 100 microns, as may be required for beneficiation by, for instance, flotation, magnetic separation or tank leaching. Dry HPGR grinding requires special attention in maintaining suitable process economics, when considering power input in grinding, drying and classification. In some cases, HPGR capacity and roll surface wear life may be negatively affected by a lack of moisture in the feed. This publication summarizes some of the features of, and experiences in dry HPGR applications. This includes design aspects of the classification system and discussion of the wear protection of the roll surfaces. The paper also includes examples of operational experiences of dry practices in minerals processing and cement plants.

Jan 1, 2012

"Acid resistant brick lined autoclaves and related vessels are utilized in pressure oxidation for the recovery of gold, copper, and other metals. The combination of the corrosion resistant membrane, acid resistant brick, mortar and steel shell is a composite system that requires a sophisticated stress analysis. In order to obtain meaningful results both the model and physical properties of the materials must be carefully selected. Evaluation of the calculated results requires an understanding of both the failure mechanisms of ceramics and experience with the performance of existing lining systems.INTRODUCTIONAcid brick lining systems are used in pressure oxidation autoclaves and related vessels to provide thermal and mechanical protection for corrosion resistant membranes that are applied directly to the interior of the vessel shell. The acid brick and mortar must be resistant to the process conditions and must provide a mechanically reliable structure.The construction of lined vessels incorporates a wide range of materials that can include the carbon steel vessel, austenitic weld overlay, lead lining, organic membrane, ceramic brick, mortars and other alloy components. The physical properties of the materials can vary by orders of magnitude and when combined in the construction of the lined vessel create a complex composite structure. The materials may be bonded together or act independently of each other. Stresses are induced into the lined vessel include pressure, thermal expansion, chemical expansion and mechanical loads.The complexity of these systems makes it is very difficult to account for all of the variables in the structural analysis of lined vessels. Historically calculations were simplified and designers primarily relied on experience with previous applications.The greatly improved tools for Finite Element Analysis (FEA) available today allow for detailed calculation of the stresses imposed on the vessel shell and lining. Koning & Lauzon (2004) presented a paper on design fundamentals including a discussion on the application of FEA methods at Pressure Hydrometallurgy 2004 in Banff. When a designer carefully constructs a model and selects the correct materials properties for the calculations, meaningful and useful results can be achieved."

Jan 1, 2012

Commercialisation of outcomes from research projects is a process often poorly understood and managed, but has the potential to achieve significant benefits for the industry and community as a whole. JKTech Pty Ltd was established in 1986 to transfer viable research outcomes from the Julius Kruttschnitt Mineral Research Centre (JKMRC) at The University of Queensland, Australia. This paper describes successful and unsuccessful examples of commercialisation by JKTech over the years, and draws some conclusions as to the factors that contribute to success and failure in technology transfer.

Jan 1, 2012

By J. Güntner

Most copper/cobalt ores from the Central African Copperbelt contain sulphidic compounds, which are not extractable in direct leaching. Roasting provides the possibility to transfer the valuable components into leachable compounds. In an operation window defined by temperature and off-gas composition it is possible to selectively oxidize iron sulphides to haematite and copper/cobalt sulphides to sulphates. Selective sulphating of the valuable minerals is an important condition for the subsequent leaching stage. The dissolved copper and cobalt are recovered by solvent extraction and electrowinning. This technology has been part of an established process for many decades. The concentrates from recent projects on the Copperbelt have lower sulphur contents, and frequently higher copper contents, than those from older projects. The paper shows the consequences of this trend for plant operation and explains useful counter actions by means of case studies. Autothermal combustion is ensured even at very low sulphur contents. Off-gas treatment has so far been based on SO2 removal through sulphuric acid production. The generated acid is used to make up acid losses in the hydrometallurgical plant section. This well-proven process combination is still the preferred route if the feed sulphur content is high enough; however, some cases may require different off-gas cleaning concepts without compromising on clean air quality. Roasting in a fluid-bed furnace remains the core of the technology. Fluid-bed roasters are easy to operate and provide an excellent control of the calcine quality. Different feeding and heat-recovery systems are used to provide a tailor-made solution for each project. Outotec built it first sulphatizing roaster in Zambia about 30 years ago. At that time, the roasting of metal sulphides was already one of the main technologies in the company. Outotec has developed roasting solutions for copper, gold, zinc, lead, molybdenum, and pyrite ores. The continuously expanded and upgraded research facilities provide an excellent basis for developing sustainable, energy-efficient, and economic solutions for copper and cobalt production in Africa.

Jan 1, 2012

By William W. Edgerton

Establishing geotechnical baselines on soft ground projects that require the use of closed-face tunnel boring machines (TBMs) is difficult. It is hard to see the face when mining and the excavated material is combined and mixed, all of which makes baseline quantifications challenging. In an attempt to meet underlying objectives of minimizing bidder contingencies, allocating or sharing risks and paying for conditions only if they occur, nongeotechnical baselines (i.e., functional baselines) have been developed. These have been used on the District of Columbia Water and Sewer Authority?s Clean Rivers (DCCR) Blue Plains Tunnel (BPT) project. This article examines the development of such functional baselines and how they were implemented on the BPT project.

Jan 1, 2012

By M. Wu, A. Kharicha, J. Bohacek, A. Ludwig

"During the horizontal spin casting of rolls, vibrations and mould deformations seems to have a significant effect on the final quality of the product. Sources for vibrations can be found in the poor roundness and a static imbalance of the chill itself. The bending of the mould axis is also considered. Both, vibrations and axis bending, are used as an input for CFD simulations of the flow dynamics of the liquid metal inside the rotating cylinder. The aim is to study the feedback of the free surface behavior in terms of wave propagation and various wave shapes. Introduction The horizontal spin casting process (HSC) is a casting process that has several advantages over the traditional gravity casting processes. Centrifugally cast products have a high degree of metallurgical purity and homogeneous microstructure. A significant gain is observed for the rupture strength, the rupture strain, and the Young modulus. These properties naturally depend on the centrifugal force and thus, the best mechanical properties can be found at the largest distance from axis of rotation. However proper selection of the angular frequency has to be done in order to prevent the so-called ""metal rain"" i.e. metal droplets can fall down from the upper part of the cylinder due to a too weak centrifugal acceleration. In the same time excessive speeds can lead to the appearance of longitudinal cracks caused by the hoop stress in the initially solidified layer. From empirical knowledge other parameters have important influence on the casting products, it includes the pouring temperature, the pouring rate, the mould coating etc. Recently the presence of natural or forced vibrations have been identified as possible additional factors to be taken into account [1-2]."

Jan 1, 2012

By Douglas Bartley

As the economy continues to slowly recover, our industry continues to finds ways to increase productivity while being forced to cut costs. The drilling and blasting process is the starting point of any aggregate or mining process. Many people refer to it as the “Primary Crusher” as it will always be more efficient to crush rock with explosives energy than it will be mechanical energy. It is the more efficient use of this energy that is addressed in this paper.

Jan 1, 2012

By Jiayan Li, Yi Tan, Yao Liu, Yaqiong Li, Shenrui Wu

"A metallurgical grade silicon (MG-Si) refining concept process was presented. Under vacuum conditions, silicon was selectively oxidized by high purity silicon dioxide to form gaseous silicon monoxide while impurities with low vapor pressure in MG-Si were rejected in residue; Then high purity silicon was obtained from the disproportionation of condensed silicon monoxide; and by-produced silicon dioxide was recycled for the oxidation step. Thermodynamics on boron rejection during the oxidation were studied in this work. In the temperature range of 1200-1800K, the saturated vapor pressure of boron, and the Gibbs free energy changes, the equilibrium partial pressures of silicon monoxide and boron oxides of potential reactions were calculated. And the effect of boron activity in MG-Si was also discussed. The results indicated that boron in MG-Si can be rejected during the oxidation and it showed the potential for the further development of the new refining process.IntroductionAs global energy consumption growing dramatically, higher prices of energy and global warming problem have attracted more and more attention [1]. As a clean and renewable energy industry, the photovoltaic (PV) industry converts solar energy to electricity using solar cell device and has a growth rate of about 30% in recent years. It has caused a shortage of silicon feedstock due to that about 90% of solar cells are made of crystalline silicon. And high energy consumption during the production of silicon material, i.e. solar grade silicon (SoG-Si), is main obstacle for its mass production."

Jan 1, 2012