Search Documents

By D P. Blair

Rio Tinto’s Hope Downs Operations are currently mining iron ore in their South Central Pit. Prior to the commencement of mine operations, Hope Downs carried out an extensive archaeological investigation and identified an ancient rock shelter lying within the proposed mine boundaries. The site is significant to the traditional owners/custodians of the land in this part of the Pilbara, and thus the final pit design was changed to preserve the rock shelter, which now lies 30 m outside the mine boundary. In order to further preserve this ancient dwelling from blast-induced damage, blast design procedures were improved over time to minimise the vibration impact when blasting close to the shelter. Blasting and vibration monitoring commenced in May 2008 using pyrotechnic delay sequences and normal-direction firing. In October 2009 electronic delays were used to reverse-fire blasts close to the shelter in order to create a damage zone between the initiating holes and the rock shelter. A detailed statistical analysis of the vibration data shows a reduction in the higher levels of vibration for blasts fired after October 2009, which is most likely caused by the created damage zone. In May 2010, a site-specific vibration model was developed and implemented, and based on Monte Carlo waveform superposition. This model was used to give a further insight and improvement to the blast delay sequences when blasting close to the shelter. However, such models are expensive to implement and have limitations, which reduces their potential for estimating the probability of getting an excessive vibration due to a given blast design. In this regard, it is more realistic and significantly less expensive to use a recently developed probabilistic analysis based on simple charge weight scaling. This analysis shows that there was a higher probability of exceeding prescribed vibration limits at the rock shelter for blasts fired before October 2009 than there was for blasts fired after October 2009.

Nov 8, 2011

By N Elith

The explosives demolition of a post-stressed, steel reinforced, concrete road bridge in Australia’s capital city, Canberra. The bridge was 50 m from the new replacement bridge, 320 m from community structures and within five kilometres of the national parliament buildings. The job required multiple overlays of risk assessment, public relations, safe work procedures, specialised blast design, environmental predictions and flyrock controls. Project stakeholders included Worksafe, Roads ACT, bridge owners, consulting structural engineers, community groups and road users. The bridge precincts, including a major road underneath, had to remain operational to peak traffic in the days leading up to the demolition. The break-up and removal of debris had to be executed in just two days from Friday to have the road beneath re-opened for Monday morning city-bound traffic.In Canberra, all explosives demolitions are now viewed with particular caution after a demolition in 1997, during which a young girl was killed. Any approval requires that Explosives Regulations, AS2187 2006 and Worksafe processes are satisfied, and a convincing case presented for blasting as a safe and viable option.Our design used specialised shaped cutting and blasting charges to sever in situ concrete beams and tendons and to shatter components of the stressed concrete bridge assembly. We include comments on structural engineering reports dealing with pre-weakening mechanisms. The benefit of pre-weakening is that it reduces the amount of explosives needed to safely complete the job and facilitates quick removal of debris after the shot. The complementary skills of the team, each one an expert in his field, resulted in a highly successful demolition, praised by authorities as an outstanding example of controlled use of explosives.

Nov 8, 2011

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By T N. Little

This review paper presents an integrated and practical insight to blasting geology and its importance. This approach involves developing blasting objective up front and implementing geology specific blast designs. The author refers to this approach as ‘starting at both ends’. There are many human-imposed controls on blasting operations, such as: safety, security, legislative, company standards, heritage, and environmental constraints. Thus it is possible for some operators to lose sight of the controls imposed by nature. This paper demonstrates how site geology controls or influences many aspects of the rock breaking processes and how a focus on this aspect has potential to add considerable value to mining operations. It is obvious that mining companies concentrate their efforts on economic/ore geology (good rock geology). However it is the author’s experience that they also concentrate on engineering geology (bad rock geology) only when forced to do so by the ground conditions, but seem to run out of puff before they apply blasting geology (big rock geology). This paper contains five main sections. In the first section, the impact of geological controls on blasthole drilling is briefly discussed in terms of drill selection, penetration rates, bit wear, blasthole stability, blasthole deviation, and health precautions. In the second section the geological controls on aspects of geometric design are reviewed. These include: hazardous minerals, valuable minerals, selection of the blasting techniques, geological structures, blasting direction, and blasting geometry. Section three overlaps with the geometric design section and deals with aspects related to explosives. Topics addressed include selecting the explosive type based on geology, distribution of explosive charge in space and time, explosive performance, and the rock response to explosive loading. In the fourth section, examples are given of the operational complexity needed to implement a blast to cater for difficult bench geologies, environment constraints, past mining (voids) and need for a high degree of quality control. Section five demonstrates geological controls on blast results. Blasting results include the muck pile characteristics, downstream handling and processing, damage to the remaining rock, and blasting emissions.

Nov 8, 2011

By D L. Kennedy

Many aspects of the physical layout of manufacturing plants and storage facilities for explosives are governed by so-called quantity-distances tables. Both the British and the American tables were originally derived from an analysis of the injuries and the building damage documented by an early 20th century compilation of significant accidental explosions. However, progressive changes in explosive process technology and in building techniques have reduced the relevance of much of this historic data set. Extensive scientific research has been conducted over recent decades to characterise the potential injuries and damage from accidental explosions under more modern conditions. This presentation will showcase some of this research.**This is an abstract only. No paper was provided for this abstract**

Nov 8, 2011

By K Guilfoyle

AngloGold Ashanti Australia Ltd operates an underground mine below a large open pit at the Sunrise Dam Gold Mine near Laverton in Western Australia. Operations are based on an extensive mineralised zone which has very complex geometry, has a high ‘nugget effect’, and is difficult to interpret and model. Initial underground ore was produced from relatively narrow orebodies dipping from 15º - 70º. Open stopes aimed to selectively extract high-grade ore, using methods including jumbo stripping and longhole drilling and blasting. The complex geology makes it difficult to accurately locate development and stopes in the positions required for profitable production. In narrow stopes, rock mass damage and overbreak dilute ore grades and increase the cost per ounce of gold poured. In flat orebodies, several different techniques have been used to recover blasted ore but overall productivity is low. Thus selective mining can also be slow, costly and recovers only a portion of the available mineral resources. Large longhole open stopes with cemented paste backfill are used to extract multiple zones of mineralisation from the Cosmo and GQ orebodies. Bulk emulsion explosives and electronic detonators are used in all large stope blasts to reduce the risk of misfires and to accurately control blasthole initiation sequences and delay timing. Larger stopes improve productivity and significantly reduce direct mining costs, enabling the use of lower economic cut-off grades which increase the overall recovery of mineral resources. This paper reviews the evolution of open stoping at Sunrise Dam, the various mining methods and drilling and blasting practices used, the results achieved, and the lessons learned.

Nov 8, 2011

By D P. Blair

The theme of this conference is blasting productivity. This article only considers the technology aspect of this theme, and in particular, the collection and analysis of experimental data. In many cases, field trials are set up to collect data on variables such as fragmentation and vibration with the aim of comparing different explosive products and/or blast designs. An important aspect of such trials is the collection of sufficient data to draw sound conclusions. In this regard, there is no doubt that the scatter in real data is the root cause of all problems of obtaining misleading results due to an insufficient number of trials. This article shows that the typical one-off trial has a high probability of producing misleading information, which could be considered to be worse than having no information at all. Assuming that sufficient data has been collected, this article also highlights the methods that can be used to make the most of that data. These methods include the application of appropriate statistics that are dependent on the nature of the scatter in the data, and the use of some of the more recent filtering and spectral approaches that can be used to reduce the noise in measured blast signals and increase the resolution of their spectral characteristics.

Nov 8, 2011

By M Breen

In 2009, George Fisher mine began to seriously consider the transition from pyrotechnic detonators to electronic detonators. Initially, the electronic detonators were used for complex crown shots or areas where ground conditions had the potential for excessive overbreak. After critically evaluating the potential safety benefits, production increases and ability to redesign stopes to better manage a thinly bedded hanging wall, the mine decided to embrace the technology.

Nov 8, 2011

By R van Wyk

In today’s mining environment the use of heavy mechanical devices and other high-tech electronic devices like two-way radios, cellular phones and even automated mining systems, form a vital part of the daily operations of a mining site. These human-made devices and some of the naturally occurring events, like lightning and gamma radiation, can have negative effects on electronic detonators and the associated control equipment.On larger mining operations the necessity to move the point of safety for blasting further away from the blast area, introduced remote firing via radio frequencies for electronic detonator systems. Other influences on electronic detonators can be abuse or ignorance. To ensure the safety of the end-user, an electronic detonator must be resistant to some common mistakes that users can make. One of main concerns here is resistance to static discharge or incorrect wiring. Despite the daily use of electronic detonator solutions, scepticism and concern still exists amongst those who believe the system raises the risk of a premature initiation of the blast through some form of interference trigger.This paper will help users understand how electronic detonators and the associated control equipment protects itself from external influences. Focus will be on protection schemes to counter static and over-voltage discharge and methods to ensure protection of secure wireless radio links and detonator communications. With well engineered communication systems and solid static and over-voltage protection, an electronic detonator system can be more reliable and safer than other detonator systems. The following main points will be discussed:what makes a detonator an electronic detonator,static electricity and over-voltage protection,the general influence of electromagnetic energy on the detonator,the influence of lightning on detonators,the protection of radio communication’s links as used by remote firing equipment, andthe safety protection features built into remote firing equipment.

Nov 8, 2011

By I Onederra

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with explosives used in the mining industry because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost-effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low-density explosives. Low-density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. There have been significant advances in the availability, reliability and flexibility of these explosives, which now offer a range of densities and degrees of water resistance. Their detonation performance is not well understood and cannot be accurately predicted with current ideal and non-ideal detonation codes. It was therefore viewed as important to be able to directly measure pressure and temperature during the detonation process of these complex mixtures in production blastholes. Identifying the pressure release patterns of both conventional and low-density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in full-scale conditions.

Nov 8, 2011

By C K. McKenzie

As more and more mining operations around the world either switch to, or trial, electronic initiation systems, the breadth of knowledge and experience regarding their effective application has widened considerably.In South America, for example, there is a strong perception that in order to achieve the finest possible fragmentation, very short electronic delays must be used between successive holes within a row. Limited field studies involving measurement of fragmentation have been conducted to support that paradigm and there are few long term studies which have been strongly supported by measurements of productivity either in the pit, in the plant, or in the leaching pads.On the other hand, some well documented studies have been conducted in North America, showing not only the impact of delay timing on fragmentation but also the effect on semi-autogenous grinding (SAG) mill productivity over extended periods of in excess of 12 months. To date, those studies suggest that optimum timing is considerably longer than the times commonly used in South America.This paper explores the current knowledge of the effects of delay timing on issues ranging from size distribution to vibration impacts in pit walls, to vibration and overpressure impacts in surrounding communities. It also explores how fragmentation modelling can be adapted to reflect fragmentation trends that have been reported in various technical conferences around the world.

Nov 8, 2011

By K G. Fleetwood

This paper proposes an approach to determine the influence of non-ideal detonation characteristics related to the charge diameter, explosive type and confinement conditions on the available shock energy of ANFO and a representative chemically-sensitised (gassed) emulsion. The proposed degrees of non-ideality of the two different blasting agents are indicated by the Gurney ratios, determined from existing cylinder expansion testing data. The influence of the non-ideal detonation properties on blast design and performance are also compared using a series of theoretical, equal powder factor open pit blasting patterns with hole diameters ranging from 102 mm to 270 mm. The non-ideal shock energy factor (NSEF), which is the available shock energy per tonne of blasted material (MJ/t), is used to compare the different blasting patterns as charged with either ANFO or the gassed emulsion of equal charge density (0.85 g/cm3). The intended purpose of this investigation is to provide explosive users with an approach to compare different explosive types or charge diameters in the absence of dedicated non-ideal detonation modelling, which is generally not available to explosives users.The results of the comparisons suggest that at low charge densities, the example gassed emulsion displays a higher velocity of detonation (VOD) than ANFO in smaller charge diameters but similar degrees of non-ideality (based on proposed Gurney ratios). The results also suggest that the confined, non-ideal gassed emulsion VOD at hole diameters greater than 270 mm can be less than ANFO due to the low density effects on the emulsion matrix. The differences in non-ideal detonation properties and Gurney ratios between the ANFO and gassed emulsion resulted in gassed emulsion NSEF values ranging from 15 per cent lower to 65 per cent higher than ANFO for equal powder-factor patterns in blasthole diameters from 102 mm to 270 mm.

Nov 8, 2011

By P K. Singh

Recent advancements in understanding the detonation process are noteworthy, but they are still based on somewhat hypothetical situations. The actual variables that are essential parts of normal blasting practice have not yet been taken into account in such treatments. These include the various initiation practices employed to detonate a column of explosive, from single point initiation to multi-point initiation in blast holes, and the effect on detonation characteristics of both detonators and explosives under multi-deck and multi-hole blasting conditions. The in-the-hole velocity of detonation (VOD) of an industrial explosive is dependent on explosive’s charge diameter and blasthole diameter. The relationship between blasthole diameter and VOD provides a fundamental guideline to the rate of energy conversion and energy release within the detonation front on the interaction of explosives with the confining medium.The in-the-hole VOD of explosives was measured at four experimental sites in India for different blasthole diameters, ie 150 mm to 311 mm, but for identical explosive composition being same particle size, density, viscosity and loaded into blastholes with the same degree of confinement. The results of the studies demonstrated that there is definite relationship in in-the-hole VOD of the explosive and the diameter of the blast hole. The study also confirmed that the explosives initiated with concentrated boosters yielded higher VOD in comparison to those explosives that were initiated with multi-point priming. The measured increase in VOD of explosives for increasing diameter of holes was up to 24 per cent. The rate of change in in-the-hole VOD of explosives increases with increasing blasthole diameter. It can be further stated that the in-the-hole VOD of the explosive reaches a fairly constant value after reaching a limiting/threshold diameter of 311 mm.

Nov 8, 2011

By J Hutchings

An essential component to the management of any process is the measurement of key parameters, used to monitor, control, and provide the feedback necessary for improvement. This paper discusses how data collection and analysis can provide a better understanding of the blasting process, as well as additional control and improved outcomes.The drill and blast process involves the generation and use of information at a number of levels. Comparison of historical parameters and results provides a starting point for the development of ongoing blast designs and a baseline against which future results can be compared. The collection of data during implementation provides a quality assurance/quality control (QA/QC) function where potential defects (such as under-drilled or over-charged holes) can be rectified prior to firing. Actual quantities and production rates allow the development of realistic plans and schedules, rather than using inaccurate estimates and targets that lead to unscheduled changes to equipment paths. Over?the past several years there have been a number of technological advances in data collection technology. Drill monitoring instrumentation on blasthole drills provides location information and feedback on rock properties as drilling occurs. Hand held ‘data logger’ technology has also overcome the challenges of working on the bench, such that blasthole measurements can be collected and forwarded directly to the explosive truck. Mine sites are becoming wireless network-enabled allowing the seamless data transfer from the field back to the office, in near real time, as that information is collected. Great strides have also been made in the development of drill and blast software systems which are more user friendly, and yet provide far greater capability to manage the quantity of data generated. The blasting process is critical to the overall mining process and the delivery of a successful blast outcome requires that the blasting process be ‘in control’. The measurement of key parameters can provide the data with which to measure and maintain control of blasting, and allows the validation of performance improvement measures and identification of improvement opportunities.

Nov 8, 2011

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By Charlie Harper

Open Pit Mining of Golden Band Resources? EP Gold Deposit Golden Band Resources Inc. (GBN:TSX-V) is Saskatchewan's newest Gold Producer. Located in the La Ronge Gold Belt of northern Saskatchewan, GBN has over 875 km2 of claims with 12 known gold deposits and 4 former producing mines. Production has begun at the Roy Lloyd Mine (Bingo Deposit), to be followed initially by our EP and Komis properties. Development of the underground infrastructure at the Roy Lloyd Mineis continuing and on schedule. Production from these deposits will feed our centrally located and 100% owned Jolu mill. We have our provincial environmental permits in place, and we have an established infrastructure including a 400 tonne-per-day mill, year-round road access, and access to grid power. Construction of the grid power line and the above ground tailings facility are now complete.

Nov 1, 2011

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By H De Beer

The 14MW SAG mill at Tarkwa, Ghana, experienced a frozen drop charge incident on 10 February 2010. This caused downtime of 112 hours, a repair cost of $200k and production loss of 162,000 tons, corresponding to a loss of $8.9M. A new locked charge protection system was installed on the two Tarkwa mills on 30 July 2010, mitigating this risk. This system calculates the ore angle in real time while the mill is starting up and trips the mill if the ore angle exceeds a trip angle setting. The calculation of the ore angle is derived from the mill motor rotor currents only - no mechanical transducers are required. The head of Gold Fields West Africa, Peter Turner, says of the new system: "This is excellent work and the type of technology that has had and will continue to have, major opportunity cost impacts on our business."

Nov 1, 2011

By Scott A. Stebbins

Cost evaluation models constructed specifically to evaluate the economic potential of an individually motorized railcar system of ore and waste transport demonstrate that the approach may be considerably more cost effective than traditional rubber-tired haulage methods. The system design places a motorized drive unit on each railcar, as opposed to the more common configuration in which a series of un-motorized cars trail behind a single locomotive. These motorized railcars are directed to various load and dump points by a computerized dispatch system, and as such have the advantage of operating unmanned. In addition, the tractive effort of the rail-type drive system is noticeably more efficient than that of the rubber-tired mode of transport. The savings are realized primarily through comparative reductions in the requirements for labor and, to a lesser degree, energy.

Nov 1, 2011

By R. C. Snider

The Roy Lloyd Mine in northern Saskatchewan is a high-grade underground gold mine which is currently supplying ore to Golden Band Resources Inc. (Golden Band)?s Jolu mill. Prior to the operation of the mine, an underground exploration program was conducted intermittently at the site. During both the underground exploration phase and mining, Golden Band has implemented water recycling to reduce freshwater usage within the mine in order to address concerns over the potential for impacts associated with freshwater usage and to reduce the volume of effluent discharged from the site. Golden Band initiated an underground exploration program at the Roy Lloyd Mine site (formerly called the Bingo Project) in October 2007 to better delineate the mineralization of the Bingo gold deposit. The exploration program provided geological information required in order to improve the confidence level of the geological resource model and also provided information to aid in the mining of the deposit, such as the determination of groundwater inflow rates. Underground production mining started in March 2011. This paper provides an overview of the mine water recycling methods implemented at the site during both the exploration and initial mining phases of the project, and the success/drawbacks of these measures to date, including the potential cost savings in the form of reduced treatment and monitoring costs inherent in a reduction of the volume of effluent discharged from the site. The paper will also discuss options that are currently being evaluated in order to further assist Golden Band?s ability to recycle water and reduce the volume of effluent discharged to the environment, while ensuring effluent discharged from the site to the environment meets criteria.

Nov 1, 2011