Search Documents

By Amaneh E. Kenarsari

Among the different sources of uncertainty in pile bearing capacity prediction including inherent heterogeneity, measurement and model uncertainties, the inherent heterogeneity of soil properties is of particular interest and is considered in this study. Cone tip resistance data are utilized to calculate pile bearing capacity by considering vertical soil variability. In this regard, cone tip resistance component of CPT data is assumed as a random parameter. Realizations of this parameter are achieved with the aid of local average subdivisions and random field theories. Monte Carlo simulation is used to generate different realizations of CPT or CPT-u data. Pile bearing capacity was then calculated by the use of direct method. Pile bearing capacity are predicted for a project in south of Iran using this method and probability density function for the total bearing capacity of pile is plotted. Coefficient of variation of 33% for ultimate bearing capacity shows the variability of bearing capacity due to variation of soil strength in depth. Cumulative probability chart for the ultimate bearing capacity are plotted as an efficient tool for estimating ultimate bearing capacity of piles with different desired confidence levels for vertically variable soil strength properties. Significant difference between mean value of pile bearing capacity (18 MN) and limit with 95% confidence level (8 MN) emphasizes the importance of considering soil variability.

Jan 1, 2011

By Gökhan Demirci, Ishak Karakaya

"Energy consumption in electrolytic magnesium cells is well above the theoretical values. However, the mechanism of the back reaction, the main cause of the current losses, has not been fully understood yet. Magnesium dissolution into the melt is generally regarded as the limiting step for the back reaction. Accordingly, present cell designs are made with priority given to fast magnesium removal from the cell. However, experimental data and modeling results in this study indicate that the limiting step for the back reaction between magnesium and chlorine is the chlorine dissolution into the electrolyte when physical contact between electrolysis products was eliminated. Effects of chlorine bubbles on the current efficiency and the cell potential were investigated. Results show that the extent of back reaction is proportional to the chlorine surface area in contact with the electrolyte per unit time, and the cell potential increases with the amount of chlorine bubbles inside the electrolyte.1. IntroductionMagnesium is less dense than the electrolyte in electrolytic magnesium production. Therefore, both electrode products, magnesium and the chlorine gas, move upwards inside the molten salt electrolyte during electrolysis. The upward motion of electrode products promotes the most important current loss mechanism, the ""back reaction"". Separation of the highly reactive species; liquid magnesium and the chlorine gas in the cell, to prevent their recombination is one of the main concerns in cell designs. The employment of large inter-electrode distance or a separation wall in early cell designs; decreased the extent of recombination, but increased the cell voltage and energy consumption. Recent cell designs, on the other hand, make use of lifting action of chlorine gas [1,2] by utilizing smaller inter electrode distances to separate the magnesium and chlorine gas faster. Although energy consumption was reduced, but more physical interactions between electrode products make electrolytic magnesium cells still highly inefficient when energy consumptions are compared with the theoretical values. Today, the most efficient industrial cells utilizing high purity feed operate at 10.5-11.5 kWh kg-1 Mg [3-5] and it is considerably higher than the theoretically attainable value of about 6.0 kWh kg-1 [6]. This large gap demonstrates the necessity of more research on physics and chemistry of magnesium cell electrolysis."

Jan 1, 2011

The mining and minerals extraction industries have often been demonized by the public as industries that put profits and production before people. It is true that the inherent danger of the work has led to more fatal accidents than anyone associated with the industry would care to remember. But, in stark contrast to what has often been said, the truth of the matter is safety is now the top priority of every miner, from the face of the longwall to the executive boardroom. Without safety, nothing else matters. This message was told and retold by representatives from some of the world?s top mining and petroleum companies from Oct. 11-13 during the inaugural Safety and Reliability in the Mining and Resources Industries Conference in Calgary, Canada. The meeting was hosted jointly by the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) and the Society for Mining, Metallurgy, and Exploration (SME). It was the first of a series of conferences to focus on these important topics. Next year, the conference will be held in Minneapolis, MN from Nov. 13-15.

Jan 1, 2011

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By John Brennan

Necessity, they say, is the mother of invention. Certainly that sentiment held true during the early stages of explosive engineering. While seaside forts were concerned over static ignition of their black powder caches in the 14th century1, the mining industry in the 1800s were plagued by accidents surrounding the ignition methods for their black powder blasts.

Jan 1, 2011

By Ragnhild E. Aune, Mark William Kennedy, Shahid Akhtar, Jon Arne Bakken

"In the present study classical induction design tools are applied to the problem of heating nonmagnetic metal billets, using 50 Hz AC. As an example of great practical industrial interest, the induction heating of aluminum billets is addressed specifically. The predicted work piece power is compared with the measured work piece power for a long and a short coil, using well established methods, such as those of Burch and Davis, introduced in 1926/28, Dwight and Bagai in 1935, Baker in 1944/57, Vaughan and Williamson in 1945, and by Tudbury in 1960. A calculation methodology based on a combination of the available tools is also introduced and discussed. The method has proven to give an error of <10% of the actual work piece power. An equation for Tudbury's work piece shortness correction factor is disclosed for the first time.IntroductionInduction heating of metal billets is a practical problem, with a geometry suitable for solution using analytical methods. This paper will examine solutions related specifically to round work pieces in round coils, although the methods presented can be extended to other regular shapes of work pieces and coils[l]. The methods can also be extended to ferromagnetic materials with slight changes[2-3]. It is assumed that the coil and work piece have a consistent diameter over their entire length and that the work piece is at least as long as the coil. Correction factors can be derived for the cases where the work piece is shorter than the coil.The study of induction heating by coils began in the late 19th century with theoreticians like Heaviside[ 4]. The work of Burch and Davis[ 5-7] in the 1920' s greatly improved the theoretical understanding of induction applied to metallurgy. Many investigators in the 1930's-1950's: Dwight and Bagai[8], Baker[l-2, 9], Vaughan and Williamson[3, 10] and others[l 1-12] added to our understanding with clearer mathematics, solutions for specific applications, semi-empirical modifications and practical design tools. Much of the accumulated knowledge is available in books, such as Tudbury's practical text or Simpson's engineering guide from 1960[13-14]. Perhaps the best description and derivation of the theoretical and semi-empirical solutions can be found in Davies[15]."

Jan 1, 2011

By Ben Blaschuk

The Bagdad solvent extraction plant was commissioned in 1969 and was the second solvent extraction-electrowinning (SX-EW) operation to be built following the Ranchers Bluebird SX-EW plant near Miami, AZ. The current operation still resembles its original form, with four independent sections that run in parallel with each consisting of many long and narrow settlers. Through its 40-year history, the Bagdad SX circuit has experienced a range of pregnant leach solution flows and grades. The unique design of the Bagdad circuit has allowed for numerous configuration changes to accommodate the changing operational conditions, while maintaining an extraction recognized in the industry as excellent.

Jan 1, 2011

By D. S. van Vuuren

Industrial production of titanium occurs via the batch-wise reduction of titanium tetrachloride (TiCl4) with a reducing metal, being magnesium in the Kroll process, or sodium in the Hunter process. In the search for low cost titanium, the CSIR is developing a continuous process to produce titanium powder directly via metallothermic reduction of TiCl4 in molten salt, dubbed the CSIR-Ti process. The move to a continuous process has been attempted by a number of organizations, but was until now always met with failure, due in no small part to challenges inherent in the process chemistry. The reaction between TiCl4 and the reducing metal can occur directly, when TiCl4 or any titanium sub-chlorides present, comes into contact with suspended or dissolved reducing metal. The reaction can also occur indirectly, without any physical contact between the reacting species, via an electronically mediated mechanism. The reaction mechanism via electronic mediation can cause TiCl4 to react at the outlet of the feed port, rapidly causing blockages of the TiCl4 feed line. The electrical conductivity of the metal reactor can also cause the electronically mediated reaction to favour the formation of titanium sponge on the reactor walls and internals, rather than titanium powder. Various methods were investigated to overcome the problem of blockages in the TiCl4 feed line, e.g. mechanical removal, sonic velocities, dilution of the TiCl4 and the use of ceramic feed lines. This article discusses problems experienced with the continuous feeding of reagents, and various methods attempted are shown and discussed. Information is also given on the morphology, chemical composition and suitability of the final titanium powder for powder metallurgical application as presently produced by the CSIR-Ti process. Keywords Titanium dioxide, titanium nitride, carbo-thermic reduction, ilmenite, slag, tunnel kiln, residence time.

Jan 1, 2011

By Zhenjun Tan, Lei Zhang, Jigang Li, Yifang Zheng, Jilai Xue

"Water electrolysis in 0.4 mol/L NaOH solution for hydrogen generation was carried out with ultrasound introduced through the anode. It was found that the cell voltage reduced by 150-300 mV in the current range of 20 mA to 40 mA with ultrasound frequency at 25.3 kHz. The cell operation became unstable when the cell current was larger than 75 mA with ultrasound. This reduction in cell voltage was due to removal of the gas bubbles on the electrode surface, which can be directly observed in the see-through cell of water electrolysis. Ultrasound with frequency of 33.3 Hz was also tried, but no better effect was obtained. The results suggest that ultrasound assisted water electrolysis can have potential in energy savings for hydrogen production.IntroductionIn electrolytic process, the electrode that the bubbles generated on its surface usually covered a thin gas film, which can be caused an additional voltage about 0.15-0.25V[l,2], especially in aluminum electrolysis. To solve the problem, loading the ultrasound removes the gas bubbles from the electrodes, this subject had been researched in recent years. From 1995 Jilai Xue et al[3,4,5]. applied the ultrasound in aluminum electrolysis in lab. The results from Sheng-De Li et al.[6] reveals that can decrease the cell voltage and have influences about the hydrogen and oxygen's output ratio. Although there are many paper about the applying of ultrasound such as in electrolysis[5,6], deposition[7,8], plating[9,10], oxidation of salts substance on the surface of electrodes[l 1] and so on, the effect of different frequencies ultrasound hadn't been investigated deeply.We focus on the anode voltage by different frequencies ultrasound and the bubble behaviors in this paper. The environment of this experiment is in alkaline solution. Through this exploration it can offer a basis for the applying of ultrasound in electrolysis."

Jan 1, 2011

By Tony Lipiec, Chris Fleming, Larry Urbanoski

In 2009, the Canadian Mineral Processors (CMP) became aware that Canadian securities regulators were amending the contents of National Instrument 43-101. NI 43-101 is a set of regulations which establish how ore resources and reserves are presented to the investing public. The documents produced under NI 43-101 are central to the ability of many companies to raise financing for their projects. With the increase of metallurgical complexity, and decrease of head grades encountered in new deposits, the role of the Qualified Person (QP) in determining process performance has become increasingly critical in determining the classification category of resources and reserves. Given the challenges confronted by those involved in defining the concentration and extraction of minerals and metals, there is a need to provide support to these QPs. To address these concerns, the CMP established a sub-committee in 2010 to create a set of guideline documents to assist the QP involved in process matters as to what should be included at the various levels of study supporting the establishment of resources and reserves in NI 43- 101. The results of the sub-committee work are presented and the considerations in the writing of the documents are discussed.

Jan 1, 2011

Currently there exist several explosive quantity-distance (Q-D) rules variously exercised by most countries to protect personnel and property against the effects of accidental explosions. These regulations apply to manufacture, transport and storage of explosive products. This paper reviews the technical basis behind these regulations, as they apply to commercial and military explosives. The characteristics of a blast wave and missiles issuing out of an explosion site and their role in determining the level of damage to a target are discussed. The need for further research on the effect of detonation of charges of non-standard geometry, and under confined conditions such as tunnels is discussed. The challenge in estimating the net quantity of explosives involved and calculation of its TNT-equivalency is also highlighted.

Jan 1, 2011

By K. Hanson

When done properly, benchmarking is an extremely effective tool for assessing ones performance, finding areas for improvement, and identifying strengths. However, when done improperly it can be an exercise in futility and result in incorrect observations and conclusions. A primary pitfall of benchmarking is collecting too much unreliable information. Surprisingly, the evolution of data storage and the ease of data collection are not helping with better data collection. Instead, it is just allowing one to collect more information, while at the same time inundating one with too much data. Additionally, the process of data collection can be tedious and is often times delegated to the least experienced individual resulting in unreliable and incorrect data collection and entry. Another primary pitfall of benchmarking is metrics that are cost based or poorly designed. Cost based metrics typically involve comparing unit mining costs ($/tonne). Between mines, unit mining costs are not very well correlated and have become further complicated by significant regional cost variations and mining inflation in the last years. Likewise, poorly designed metrics lead to poor benchmarking results. Examples of poorly defined metrics include: metrics that rely on information that is difficult to collect, metrics that are poorly defined, metrics which are too site focused, and metrics that measure low consequence practices.

Jan 1, 2011

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011

With commodity prices rising again and market conditions stabilizing, the Metals Economics Group (MEG) found that most mining companies increased their exploration budgets in 2010. In the groups 21st edition of the Corporate Exploration Strategies (CES), MEG found a 44-percent rise in the estimated worldwide exploration total for 2010. MEG found that the estimated total 2010 budget for nonferrous metals exploration reached $12.1 billion, reinstating almost two-thirds of the industry?s $6 billion in cuts to exploration in 2009. Nonferrous exploration refers to expenditures related to precious and base metals, diamonds, uranium and some industrial minerals; it excludes iron ore, aluminum, coal, and oil and gas. In 2008, exploration budgets were at an all-time high of $14.4 billion. This capped a six-year run in which budgets rose. In 2009, nonferrous exploration budgets dropped 42 percent in 2009 as the global economic crisis and declining prices for almost all commodities took their toll on the industry. Metals prices - the primary driver of exploration spending - have improved markedly since bottoming in early 2009, and have traded well above their long-term trends throughout 2010. In response, major, intermediate and junior companies have all increased their aggregate exploration allocations in 2010. In particular, the significant improvement in the availability of equity financings for the juniors over the past 12 to 18 months has allowed this group to account for the largest share of the overall increase in exploration spending this year.

Jan 1, 2011

Joy Mining Machinery has developed a new generation of ultra-heavy shields for Anglo Coal Australia?s Moranbah North Mine in the Bowen Basin region of Queensland. These are the largest two-leg longwall shields yet produced by Joy. The longwall at Moranbah North posed a number of challenges, among them a thick, inclined, sometimes undulating seam with increasing depths. The result of this was the need for larger, heavier, more powerful roof supports. Knowing that future longwalls would be going deeper, mine management determined that shield yield ratings of at least 1,750 t (1,930 st) was what would be required.

Jan 1, 2011

By John Stankus

Accurate evaluation of stress and geological conditions is critical to ground control design in underground openings. For a mine slope entry, the problem becomes more complicated because a slope transverses through many different types of strata. Mine slope ground control has traditionally been practiced based on trial and error and prior experience. There is currently no well-accepted slope and support design methodology available for an economical and technically sound ground control plan. Over the last few years, Keystone Mining Services, LLC (KMS), the engineering affiliate company of Jennmar Cooperation, has developed a ground support design methodology called the ?Stress, Geologic, and Support design system? (SGSSM). This patent pending method enables accurate analysis of actual geo-technical conditions and stress; identifies strong, fair, and weak sections along the slope; formulates primary and supplemental roof bolting systems, designs optimal long-term steel structure support; and verifies the adequacy of the developed support. The method has been successfully utilized on various new slope projects and has been well received by state and federal regulatory agencies during the approval process. This paper details the concepts of the methodology using an actual case study of a slope project in the Midwest.

Jan 1, 2011

By Willem Le Roux

The common law requires an employer to take reasonable steps for the safety of employees. In general, the duty of care means that the employer, acting personally or through its employees or agents, must take reasonable care for the safety of its employees (Van Deventer v Workmen?s Compensation Commissioner; 1962 (4) SA 28 T; Oosthuizen v Homegas (Pty) Ltd 1992 (3) SA 463 T).The duty of care includes the provision of safe premises, safe machinery and tools and a safe system of work. The obligation is not an absolute one, but is restricted by the concept of reasonableness. The common law duty may, in certain cases, include the assessment of hazards and risks. 2 International law Great emphasis has been placed in the Western world on the prevention of occupational diseases and injuries. Detailed statutes and regulations govern specific industries in many countries. See, e.g. the Control of Substances Hazardous to Health Regulations of the United Kingdom and various regulations applicable to the use of asbestos and lead, fire protection, mines and quarries, petroleum, etc. Risk management is an important part of managing health and safety. In the United Kingdom, the Management of Health and Safety at Work Regulations, 1999, require every employer to make a ?suitable and sufficient assessment of the risks to health and safety of his employees to which they are exposed whilst they are at work?. The particularity of the assessment is determined by the risk in question.

Jan 1, 2011

By Frank Field, Randolph Kirchain, Elisa Alonso, Richard Roth, Nathan Fleming

"High material prices and price uncertainty can be harmful to manufacturing firms. Increased use of recycled materials, industry-wide, can lower both material prices and price variability; moreover, increased recycling decreases the use of primary material, which mitigates price increases due to scarcity effects. These stabilizing and price lowering effects are explored using an Aluminum industry model. We show that (a) increased recycling leads to smaller price fluctuations in the presence of a primary metal supply perturbation, and (b) that the more substitutable the secondary metal is for the primary metal, the lower the overall material price is.IntroductionThe price of an industrial metal is expected to be a function of both the marginal cost of extraction and its scarcity[l-2]: where scarcity can be defined as the degree to which anticipated demand exceeds the known supply. Recycling end-of-life metal increases the apparent supply of the metal, or-in a functionally equivalent, but alternative conception-lowers the demand for primary metal; this lowers primary metal scarcity and should, theoretically, reduce its price. To the extent that this theoretical prediction holds true, recycling can provide benefits to consumers of industrial metals in the form of lower prices.Using a platinum industry model, prior work by Alonso[3] has shown that increased industrywide recycling can reduce metal price volatility because the secondary metal production (a) offsets virgin metal depletion, and (b) responds to supply-demand balance fluctuations more rapidly than the primary market. However, Platinum is not a typical industrial metal in the sense that secondary metal is perfectly substitutable for primary metal: Both primary and secondary platinum metal are functionally equivalent and have a common price. Other metals, such as secondary aluminum which is used as an example case in this study, contain varying degrees of other elements that were either intentionally added, or were inadvertently mixed in with the metal during the scrap recovery process. Consequently, different grades of scrap exist that have different profiles of elements in their composition. Depending on their particular profile of elements, more or less of a given grade can be used as a mass fraction of the final alloy-the secondary metal is not perfectly substitutable for the primary metal. For the purposes of this paper, the aluminum mass fraction of the final alloy that can be made up of secondary aluminum is termed the secondary substitutability of that grade in that alloy."

Jan 1, 2011

By O. M. S. Rodrigues

The kaolinite presence in bauxite ores increases caustic soda consumption during the digestion step in the Bayer process. Depending on the kaolinite content, the utilization of the ore in the Bayer process may be unfeasible. This investigation addressed the variables involved in kaolinite flotation through microflotation experiments in a Hallimond tube and zeta potential determinations. The tests were performed with a pure sample of kaolinite (96%). Five collectors were tested: Duomeen T (DT), cetyl pyridinium chloride (CPC), cetyltrimethylammonium bromide (CTAB), dodecylamine (DDA) and Flotigam EDA (EDA). Four of them performed well as collectors, at a concentration of 1x10-4 mol/L: CPC, CTAB, DDA and EDA. The kaolinite isoelectric point (IEP) was determined at pH = 4.6. The IEP was shifted towards higher pH values in the collectors? presence, indicating specific adsorption onto the mineral surface.

Jan 1, 2011

By W. E. Falck, A. Usubiaga, J. Spangenberg, P. Schepelmann, S. Šolar, D. Wittmer, F. Blanchard

The extraction and processing of mineral resources may be accompanied by environmental impacts. In spite of technological advancements, the enormous increase in production volumes within the last decades has induced sizeable environmental impacts along the life-cycle of products. Beside environmental impacts, social issues associated with mining need to be considered to ensure the social acceptability of mining activities. The project EO-MINERS aims at deploying Earth Observation (EO) tools to inform best practices in mining and to thus assist the global mineral resources industries in their transition to sustainable development. In order to facilitate the handling of complex sets of information requirements from a wide variety of stakeholders, a set of indicators was developed that will inform the process of EO tool and services development. The project strives to enable stakeholders outside the industry to meaningfully participate in decision-finding processes on mining-related issues by developing and providing EO products and services that fit the information requirements. The project has identified a wide range of such information requirements by stakeholders that could be potentially provided by EO tools. The applicability of the EO tools on the local level is tested on three mining sites.

Jan 1, 2011