Search Documents

By H. J. White

Haynes International, a world leader in the manufacture and production of nickel, and cobalt base alloys has invented and developed a low cost high temperature material, with a unique combination of superior oxidation resistance and weldability/ fabricability. HAYNES® HR-224TM (Ni ? 27.5Fe ? 20Cr ?3.8A1 ? 0.3Si ? 0.3Ti) forms a planar/ continuous/ adherent aluminum oxide film at high temperatures which has been shown to effectively limit chromium poisoning in solid oxide fuel, cell, systems. A 20,000 pound vacuum induction melted (VIM) + electroslag remelted (ESR) heat has been melted and converted into various product forms: sheet, plate, bar, welded tubing, wire, etc. The alloy was designed for service in severely oxidizing environments recuperators, automotive catalytic converters, wire strand annealing furnace tubes, etc. and has been of great interest to solid oxide fuel, cell, manufacturers as a materials of construction in balance of plant (BOP) design. This manuscript presents the physical, properties, mechanica, properties, and oxidation resistance of the alloy compared to other materials being considered for solid oxide fuel, cell, design

Jan 1, 2010

By Joao Felipe Costa, Jair C. Koppe, Andre Zingano, Cleber Gomes

"Run-of-mine Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. A large amount of waste results from the coal preparation, and it must be disposed of in waste piles or waste dams, depending on the material size. These waste disposals are the cause of serious environmental problems, not only in the short and medium terms, but mainly in the long term, due to the risk of provoking acid drainage or spontaneous combustion. Waste disposal requirements also demand large areas. Other problems include the pillar and roof stability in abandoned and mined out areas, building of edifices on the old and active mines, and mining under urban areas. To solve these problems simultaneously, backfilling the entries in mined out areas began with two objectives: to understand the mechanical behavior of the filling material and to model the backfilling of room-and-pillar coal mine entries through numerical simulation. Laboratory tests were performed for different filling material (with and without cement) to determine its mechanical properties and failure criteria. Based on this study, it was possible to conclude that the backfill method is a good strategy to improve the ground stability in room-and-pillar coal mines for the long term, especially for weak coal seams, and to reduce the quantity of material on waste piles on the surface.INTRODUCTIONRun-of-mine (ROM) Brazilian coal has high ash content and low calorific power. Therefore, the coal must be washed to achieve the power plant specifications for burning coal. Two types of waste are associated with power plants that bum coal for energy generation: 1) the waste from the coal preparation plant and 2) the ash from the power plant after coal burning.The Brazilian coal ash content in the ROM coal is between 45 and 55%. The clean coal is 20 to 30% ash for 4,500 kcal/kg (18,000 BTU). The coal preparation plant recovery is only about 35%. Santa Catarina State (SC) produces about 7 million tons/year of ROM coal, which results in a total of 4.5 million tons of waste. This is a large amount of waste that must be disposed of in waste piles or waste dams, depending on the material size. The waste and ash content is represented by silicate materials, such as clay and sand, and by sulfide materials, like pyrite and organic sulfur (between 1and5%)."

Jan 1, 2010

By Hitch M.

Many mining wastes, especially those from the metal mining industry, have traditionally been treated as a matter of little or no value and in practice a cost burden. Some wastes, due to their reactivity characteristics, have emergent values that go beyond purely economic and into the environmentally beneficial realm. This paper discusses the changing paradigm of mine waste management. Such fundamental parameters such as cut off grade, and strip ratio, are positively impacted by the revaluation of waste rock material. Mine rock waste can now be seen as a commodity of value, similar to the underlying ore being mined and influences the economic performance of suitable projects. This valuable material can be used for industrial purposes including acid neutralization as well as the capture and long-term disposal of anthropogenic carbon dioxide. The Turnagain Nickel project, located in northern British Columbia serves as an example of how waste rock material can become an important matrix for carbon capture and sequestration and can benefit economically from it. By producing material that has emergent economic value as well as carbon capture and sequestration capabilities, the sequestration matrix producer is a beneficiary of new carbon credits that have a market value and is looked upon favourably by regulatory authorities and affected stakeholders.

Jan 1, 2010

By Paul J. Axtell

Self-hardening cement-bentontie (c-b) slurry walls were constructed as shear walls to stabilize the downstream slope of Tuttle Creek Dam near Manhattan, Kansas. The slope stabilization was required to protect the existing pressure relief well system located at the downstream toe of the dam. The wells require protection from slope deformation induced by liquefaction of the foundation sands during or immediately after the design seismic event. The shear walls are transverse to the axis of the dam, unreinforced, and relatively brittle members that may be exposed to relatively large shear strains, and possible cracking, during or immediately after shaking. An extensive laboratory investigation was conducted on recovered core samples to optimize the mix design and stabilization scheme. Furthermore, as is the topic of this paper, a portion of the laboratory investigation was to determine the large-strain, or post-peak, shear strength of the c-b material for use in limit-equilibrium slope stability analyses and numerical deformation modeling to assess the magnitude of permanent deformation caused by the design earthquake. These data may be beneficial to other projects that are considering the use of unreinforced c-b slurry walls for seismic retrofit purposes.

Jan 1, 2010

By Matthew E. Meyer

The intent of this manual is to provide guidelines for observing and documenting the installation of ACIP piles. The manual may also serve as a guide for the training of inspection personnel. It is expected that the general guidelines and procedures described in this manual for the inspection and installation of ACIP piles will be supplemented by engineering judgment, local practice, and experience. ACIP pile construction procedures will vary depending on soil, rock, and groundwater conditions. This manual represents a wide range of possible applications in a variety of projects. It is not intended to be applicable in all situations nor replace engineering judgment for any given project. Therefore, an all-inclusive inspection manual is not considered practical or desirable. This manual should not be used to interpret or replace project specifications. It has, however, been prepared to complement the Augered Castin- Place (ACIP) Piles Manual model specification (DFI, 2003).

Jan 1, 2010

By Michael Young, Josh Rubenstein, Michael Cooper, Tom Shouldice, Dan Curry

"Xstrata Nickel Australasia’s Cosmos plant in Western Australia is currently implementing a debottlenecking project to increase nickel output while maintaining metallurgical performance and a low unit cost for production. Mineralogical analyses indicated that the processing bottlenecks could be removed by simply reconfiguring portions of the circuit as well as adding capacity with technical advancements – notably an IsaMill™, Jameson Cell, Wemco® SmartCell™ and Larox Filter.The Wemco® SmartCell™, which is particularly suited for coarse mineral flotation, and Jameson Cell, which is particularly well suited for fast floating and fine minerals, combine as rougher scalpers to complete the main stream portion of the flotation circuit. Addition of the two new cells meet the required flotation capacity to handle the forecast increase in nickel feed grade and tonnage.The addition of an IsaMill™ for regrinding allows the SAG mill to produce a coarser primary product, thus enabling increased throughput. The advantages offered by the IsaMill™ include operation in open circuit (internal classification), an inert grinding environment (ceramic media) for better downstream flotation (“clean” new surfaces), compact footprint (easy to retrofit into existing plant) and energy efficiency. With the new rougher capacity addition, the remaining original plant cells were reconfigured to suit the new regrind mill and cleaning requirements. The existing 24 m2 Larox pressure filter was replaced with a larger 32 m2 unit to dewater the increased concentrate output.The paper describes the upgrade at the Cosmos concentrator with particular emphasis on the mineralogical data and metallurgical benefits associated with the changes.INTRODUCTIONThe Cosmos concentrator is located 680 km northeast of Perth in Western Australia. The deposit’s development and operations were started in 1999 by Jubilee Mines NL, Cosmos’ previous owner, with the first production of nickel concentrate in April 2000. The Cosmos concentrator treats a komatiite hosted high grade nickel sulphide ore, with sulphides being predominantly pentlandite and pyrrhotite with lesser amounts of pyrite and chalcopyrite."

Jan 1, 2010

By P. Comba

The U.S. Bureau of Mines investigated a hydrochloric (HC1)-calcium fluoride (CaF2) leaching procedure to treat domestic manganese (Mn)-bearing silicate resources. The proposed process is an alternative to high-temperature and energy-intensive extractive techniques. Single-stage leaching with a stoichiometric amount of HCl and a F-Mn mole ratio of 0.2 extracted 96 pct of the Mn when the leach conditions were 50° C, 3 h, and 35 pct solids. Ninety-eight percent of the Mn was extracted during countercurrent leaching at similar conditions. A process flowsheet was developed that incorporated HC1-Cab leaching, excess leach acid utilization, fluoride (F) recycle, and Mn recovery. When the domestic manganese silicate ore was processed, 98 pct of the Mn was extracted, 99 pct of the Cab was reclaimed, and a leach residue was produced that passed the Environmental Protection Agency (EPA) Extraction Procedure (EP) Test for nonhazardous waste.

Jan 1, 2010

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By B. Broms

The "Bawang Pile" (in english "onion" pile) described in the article consists of a cased concrete shaft and an expanded base. The steel casing is first driven by an internal drop hammer and then the base is formed in-situ by the raming the concrete at the bottom of the slitted casing. This new type of pile can be used for underpining (small head room) of buildings and as foundation for transmission towers or lamp posts. Full-scale load tests in compression and in tension on the Bawang pile and on steel pipe piles demonstrate the dramatic increase of the ultimate capacity due to the expanded base. Guidelines for the design of such piles are proposed.

Jan 1, 2010

By J. M. Pei

In this paper, the nonlinear finite element analysis is used to study the support system of a tunnel which is designed to pass through deep-embeded stratum. The rock mass is rather intact, though a section of tunnel will pass through the weak belt. Under the influence of the high ground stress, the condition of stability and the form of support become complicate. This paper, talcing into account the nonlinear properties of rock mass and the Interaction between rock, and support, makes a comparison between the two kinds of soft and rigid support systems, and analysed the changes of their bearing forces.

Jan 1, 2010

Australia is a hub for mining technology development. The paper describes many of the key players involved in mining research in this country along with some of the interesting research outputs to emerge over the past decade.

Jan 1, 2010

By A. R. Kiani-Rashid

In this paper, the effect of aluminum content on the formation mechanism, volume fraction, morphology and particle size distribution of graphite has been investigated. Addition of aluminum on ductile iron causes some fundamental changes in iron-carbon phase-diagram and as a result, improves the graphite formation during eutectic transformation. The results reveals that aluminum compounds have been formed in the core of graphite nodules, thus aluminum plays an important role in the formation of graphite nodules. Furthermore, it is indicated that an increase in the aluminum content also leads to an increase in the number of graphite nodules and a decrease in the nodules size. By using EPMA, the segregation of aluminum and silicon between graphite nodules has been studied

Jan 1, 2010

By J. Bélanger, B. Semlali, M. Grenon

RÉSUMÉ La conception des fosses ainsi que l'évaluation des ressources géologiques et des réserves minières sont désormais réalisées entièrement à l'aide d'outils informatiques spécialisés. Cependant, plusieurs analyses, pourtant essentielles à l'évaluation de la viabilité du projet, sont réalisées en parallèle sans véritable optimisation ni synergie avec l'ensemble des données disponibles. Cet article présente deux approches permettant d'intégrer certains types d'analyses aux modèles de blocs miniers. Ces approches permettent de quantifier la broyabilité du massif rocheux ainsi que d'étudier la stabilité des pentes minières à même les outils d'optimisation et de planification minières. Cette méthode permet dès l'étude de faisabilité d'un projet minier de maximiser les données disponibles, menant ainsi à une approche plus intégrée en conception minière. De plus, ces approches sont flexibles et permettent d'évaluer rapidement plusieurs scénarios, tout en laissant la possibilité de bonifier le modèle et de revoir la conception tout au long du projet minier.

Jan 1, 2010

By Wm. Reisz

There is no universal standard for Standard Operating Procedures (SOP’s). Every blasting operation has its own unique circumstances, its own methodologies and its own unique demands. It would be nearly impossible to create a one-size-fits-all document that would be totally appropriate for every blasting scenario. But there are universal objectives that should be adopted in any set of blasting SOP’s.

Jan 1, 2010

By Jonathan Duncan, Tim Burgess, William Kendall, Jens Lange

"Steel wire mesh is the accepted standard for roof and rib skin control at most coal mines in the United States. Wire mesh is delivered to the mine in bundles that are heavy and awkward to handle. The large size, stiffness, and weight of the wire mesh can present a safety hazard in transporting underground and storing on the roof bolter. Installing wire mesh on the roof and ribs with the roof bolter can be a challenge as well.Synthetic mesh is lighter than wire mesh and can be folded and rolled into a safe, manageable size. A single synthetic mesh roll large enough to cover the roof and ribs in a deep cut can be safely handled by two men. The roof bolter is designed to carry and dispense the roll as it advances and installs primary roof support, resulting in a single pass roof and rib ground control solution. This paper focuses on the design and implementation of the roof bolter synthetic mesh handling system developed by J. H. Fletcher & Co., Huesker, Inc., and Oxbow Mining.INTRODUCTIONRoof and rib skin control in some coal mines has been an issue since mining first began. Roof and rib skin problems vary from mine to mine. The type of roof rock material exposed after mining; the mine atmosphere; and stresses from depth of cover, over mining, and/or undermining are some of the variables that can contribute to roof skin problems from mine to mine.Potential roof and rib skin problems can be time dependent as well. Some mines have roof skin rock, sometimes called draw rock, that falls when drilling the hole for the roof bolt as the initial roof support is installed. Some roof skins are more stable but can fail over time. The failure of roof skin can even be between properly installed roof bolts with roof plates (Figure 1).Mines have most commonly used a wire mesh that comes in individual panels anywhere from 5 ft x 5 ft (1.5 m x 1.5 m) all the way up to 5 ft x 16 ft (1.5 m x 4.9 m) in size. They are typically constructed of 8- or 9-gauge wire welded on a 4 in (102 mm) square pattern. A 5 ft x 16 ft (1.5 m x 4.9 m) panel weighs approximately 35 lbs (16 kg). These steel wire mesh panels can make it a difficult and sometimes dangerous task to deliver them from the surface to the roof bolter and then store on the machine. Manipulating the mesh panels from the storage area on the machine to the final installation position on the roof or rib can also be a daunting task (Figure 2)."

Jan 1, 2010

By Sergio N. Monteiro

Jute fiber reinforced polymer composites are among the most investigated and applied natural composites. In this past decade the mechanical properties of these composites has been assessed for various types of test conditions. However, the reported results correspond mainly to short-cut jute fiber composites, which do not present the highest mechanical strength as compared to continuous fibers of the same kind. In order to complement these results, the present work evaluated the mechanical behavior, by means of flexural tests, of polyester matrix composites reinforced with continuous jute fibers. Bend tests were conducted in standard specimens with up to 40% of jute. Fracture analysis by SEM displayed the rupture mechanisms. The results showed an improvement in some flexural properties with incorporation of jute fiber. However, a low fiber/matrix interfacial stress was responsible for limitation in the values attained by some properties.

Jan 1, 2010

By Jilai Xue

Fe-Ni alloys can be used as raw material in making stainless steel. Laterite nickel ore is one of mineral resources for producing nickel alloys. In this work, the laterite ore after dehydration at 800 °C and the anthracite as reducing agent were mixed for pre-reduction at 900 °C, and then reduced to form Fe-Ni alloys at 1550-1620 °C through carbon-thermal reduction process. A high Ni-content alloy component in the metallurgical mixture can be formed through pre-reduction. Better separation of the resulting metals from the slag is found with lower Ni-content alloys produced or higher temperatures during reduction. An effective processing of Fe-Ni alloys needs further understanding of the process fundamentals and optimizing of the process parameters.

Jan 1, 2010

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By Z. M. Zhang

Fracture grouting is a particular technique which can be used in soils and rocks with low permeability to increase groutability and penetration rates and to solve some special foundation problems by inducing limited and controlled zones of hydrofracture surrounding the injection source. The present paper describes the basic principles of hydrofracture and its application to grouting in deep foundations, and indicates some recognitions about the mechanisms and effects of fracture grouting.

Jan 1, 2010

By J A. H Campbell

AK6 is a Cretaceous aged kimberlite located in the north-east of Botswana, close to Debswana's Drapa and Letlhakane Mines. It was discovered by Debswana in 1969, but was considered unattractive from an economic perspective. In 2003, Debot Prospecting Pty Ltd ('Debot') re-assessed the area and with the advent of new prospecting technology, particularly large diameter drilling ('LDD') and more detailed ground geophysical surveys found AK6 to be of interest. In 2005, the Boteti joint venture was formed between Debot and African Diamonds plc ('AFD'), which covered a number of Prospecting Licenses, including that which contained AK6.

Jan 1, 2010