Search Documents

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By H. D. Mtegha

Mining is important to the economies of both Tanzania and Namibia. Recently, both nations revised their national mineral policies to ensure future economic benefit. The main difference in the mineral policy-formulation processes followed by the two countries is identified as the degree and timing of stakeholder involvement during the articulation process. In the case of Namibia, the stakeholders were involved from the start in identifying issues and in suggesting policy solutions. In contrast, the Tanzanian process involved stakeholders after a framework had been developed by a task team. The Tanzanian emphasis was on attracting foreign investment into a traditionally state enterprise system of mineral investment and development. One can argue that the policies developed met the initial requirements, and both are, therefore successful, despite the different processes of policy formulation that were used. However, several fundamental questions arise as a result of the two approaches. This paper attempts to answer these questions by providing a comparison of the processes used for developing and formulating the mineral policies of Tanzania and Namibia. It concludes that the Namibian consultative process is perhaps more sustainable in the long-term because of its wider public support. Time will tell which of these policy-formulation processes provides a basis for sustainable economic growth for developing mineral economies.

Jan 1, 2010

By X. Wu, W. R. Chen, J-G. Legoux, B. R. Marple, E. Irissou

Cold gas dynamic spray (CGDS) has been considered a potential technique to produce the metallic bond coat for TBC applications, because of its fast deposition rate and low deposition temperature. This paper presents the influence of spray processes for bond coat, including air plasma spray, high velocity oxy-fuel, and in particular CGDS, on the oxidation performance of TBCs with a Co-32Ni-21Cr- 8Al-0.5Y (wt.%) bond coat. Oxidation behaviour of the TBCs was evaluated by examining the coating microstructural evolution, TGO growth behaviour, and crack propagation during thermal exposure at 1050°C. The relationship between the TGO growth and crack propagation will be discussed.

Jan 1, 2010

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010

By S. Boisvert

Risk-based Inspection (RBI) addresses the challenges associated with ageing plants by focusing the inspection effort on the process equipments with the highest risk, thereby improving plant safety and reducing inspection costs. The RBI methodology is commonly used in the oil industry through the API 581 standard. Since no such standard exists in the mining and metals industry, BPR-Bechtel has developed one using inspection data from process equipments in CEZinc. Models were developed for various damage mechanisms, such as uniform corrosion and stress corrosion cracking. The equations were organized into a user friendly software that facilitates the implementation process.

Jan 1, 2010

By James Cornwell, John A. Elton

"Thermionic induced reactions and radiation resonance catalysis of aluminum and aluminum oxide materials exposed to microwaves and triboemissions will be described and explained from both a fundamental and practical level. Magnetron operation at distinct operating conditions that generates both plasmon and triboemissive radiation will be explained and the resulting tribochemical and radiation resonance catalytic reactions between aluminum, aluminum oxide, water and graphite will be delineated. The generation of hydrogen from these materials using triboemissive radiation and microwaves will be described, and the application of this methodology for hydrogen based technologies will be discussed.IntroductionProtective Systems Directed Energy RadiationProtective Systems, Inc, has developed a new radiation device called the EMR (Electromagnetic Resonator) that has unique characteristics that separates it from traditional microwave and rf radiation devices. The radiation from the EMR device is generated using a modified electronresonance magnetron with proprietary filters and operating characteristics.Electronic Device Shutoff. When electronic devices such as cell phones, computers, and other IC based electronics are placed within the EMR radiation, these devices become non-functional as long as the EMR beam is active. Upon removal of the EMR radiation the devices either become operational again or become operational after a cold start. The devices are not damaged by the irradiation.Faraday Cage Interaction Effect. When any of the above electronic devices are placed in a Faraday cage and activated within the Faraday cage without EMR radiation, they operate normally. However, these devices will still be rendered inoperative when an EMR beam generated outside the Faraday cage is directed at the electronic."

Jan 1, 2010

THE FUTUREGEN CLEAN Coal project will be the recipient of $1 billion worth of federal stimulus money by way of the U.S. Department of Energy (DOE), which announced the commitment to the project. The money is expected to kick off years of further work that could finally see the project completed. One of the companies involved, Ameren Corp., said the $1.2 billion project ? which will include some private funding ? still has a number of hurdles to clear.

Jan 1, 2010

By F. H. Chen

the Rocky Mountain Region since 1950, drilled pier foundations have been widely used to combat structural movement problems in expansive soils. It is now an accepted practice for engineers to use drilled pier foundations in expansive soil areas. Piers are generally drilled into bedrock in a zone unaffected by moisture change. With some exceptions, such system has successfully prevented damage incurred in the structures as the result of soil expansion. In the last 15 years, no significant advancement has taken place in the design of the drilled pier system on expansive soils. Numerous failures continued to be reported. Causes for the failures were placed on poor drainage, inadequate void under the grade beams or mushrooms on top of the piers. Engineers realize that these are certainly not the major problems. The basic design criteria should be critically reviewed. It is the purpose of this paper to point out the actual problems confronted by designers, the failure module and remedial measures, The writer does not claim to have the solutions. In fact, it will be a long time before real solutions can be found, yet the writer believes the engineering communities, the construction industry and the general public should be aware of the true picture of the problem.

Jan 1, 2010

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By Matthew Graham, Tapan Goswami, Geoff Brent

In dragline coal mining operations, throw blasting is used for the controlled placement of overburden to maximise coal exposure rates or to minimise overburden removal costs. This may necessitate sacrificing thin coal seams, generally less than one metre in thickness, which are often present in proximity to the main coal seam. This represents not only a significant loss of potential revenue and profit but also a waste of a valuable energy resource.

Jan 1, 2010

By Kara A. Teacoach

Current regulations for fire suppression systems in underground coal mines to protect conveyor belt installations have been in place since the Coal Mine Health and Safety Act of 1969 was enacted. Over time, the coal conveyer equipment being used and ventilation conditions underground have changed significantly, particularly the width of the conveyor belts and the use of belt air at the face. The effect of these new conditions on the effectiveness of suppression systems during a fire is not known. The National Institute of Occupational Safety and Health (NIOSH) conducted a study to evaluate the effect of air velocity, water sprinkler activation temperature, and a limited water application time on the effectiveness of water sprinkler fire suppression systems to extinguish large-scale conveyor belt fires. The fire tests were conducted using both new and used 1.8-m-wide, fire-resistant rubber belt that met the Mine Safety and Health Administration (MSHA) flame resistant requirement specified in Title 30, Code of Federal Regulations, part 18, section 18.65 (also known as the 2G test). Tests were conducted using standard response sprinklers with activation temperatures of 68 °C and 141 °C at air velocities of 0.5 and 5.1 m/s. Two tests were conducted at both air velocities for each sprinkler activation temperature, one using a new belt and one with a used belt. The results showed that the suppression system was able to suppress the fires in ten minutes to the point that a miner could extinguish it with a fire hose. However, in several of the tests, the fire reestablished itself a few minutes after the sprinkler water supply was cut off and quickly grew out of control. This report discusses the large scale experimental configuration, the installation specifications of the fire suppression system, and the results and conclusions regarding the effect of air velocity, sprinkler activation temperature, and limited water application on the suppression system performance.

Jan 1, 2010

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By L. Z. Xie

The results of the experimental study on the static behavior of single piles subjected to repeated and reciprocating axial loadings are recommended in this paper. Tests of four full-scale single piles of two different lengths under repeated loading and those under reciprocating loading have been conducted using the slow maintained load test method. All the eight piles were instrumented with strain gages located along the shafts. The study showed that for repeated loads below a certain critical value the total displacement of the pile top approached gradually a constant value. However, any repeated load greater than the critical value resulted a residual displacement per cycle, and that the reciprocating load capacity of a pile was dependent on the ultimate bearing capacity of the pile in tension and both were in the direct ratio.

Jan 1, 2010

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By Z. Q. Wang

The author is trying to clarify the existing problems in designing and laying out dynamic consolidation for soft ground improvement. Field testings and observations including vibrational parameters, pore pressures, stereoscopic photogrammetry etc. were run in order to trace the real behaviour of ground movement during tamping. It is believed that all the data got from the field work are rather informative and illustrative than that from theoretical modelling in the laboratory, thus some highlights relating effective thickness of compaction, maximum spacing between compaction points, number of blows for optimum tamping and seismic attenuation for environmental consideration are given.

Jan 1, 2010

By C. P. Naudé

Mechel, a large, integrated steel, stainless steel, and ferroalloy producer in Russia is committed to upgrading its facilities to world class pyrometallurgical process and environmental practice. Yuzhural Nickel currently uses shaft furnaces to produce a matte containing iron, nickel and traces of cobalt. This rather old technology is thermally inefficient and is characterized by high operating costs. Mechel has investigated suitable equipment and processes to upgrade the plant, and awarded a contract for the construction of a 12 MW DC smelter, located near the town of Orsk, to Bateman Engineering Projects in June 2008. The selection of DC furnace technology for laterite smelting can be considered as a strategic highlight for the pyrometallurgical treatment of low-grade lateritic ores, and could be the first industrial-scale implementation of this technology. This project has been designed to achieve multiple goals including the demonstration of the process and associated equipment technology at commercial scale, to confirm the scale-up design parameters of the forthcoming 2 x90 MW, twin electrode DC furnaces, and to prove the environmental emission superiority of closed furnaces. It also provides a valuable operator training platform. This paper deals with the process design, key technology building blocks and design features which have been incorporated to produce a pyrometallurgical vessel capable of (i) resisting slag superheat and chemical aggressiveness, (ii) process fine material without pre-agglomeration, (iii) achieve high nickel recoveries and(iv) being tolerant to the variations in chemical composition of laterite ore. The approach to increasing campaign lives between partial and complete rebuilds, through the use of composite furnace module (CFM) technology originally developed and patented by the University of Melbourne, is also followed in more detail. Unfortunately, results from hot commissioning and lessons learned from initial operation are not available because the project completion has been delayed due to the worldwide downturn in demand for commodities. Keywords DC furnace, ferronickel laterite smelting, corrosive slag, coppercooler technology.

Jan 1, 2010

By R. T. Swinderman

This paper discusses how many of the common practices in conveyor specification and design are out of date compared to the current expectations of users for safe, serviceable, reliable, and fugitive material-free conveyance of bulk solids. Ten of the most common mistakes made in the specification and design stages related to user expectations are reviewed along with the cost vs. price implications of those decisions. A general specification and design hierarchy that designers can use to improve conveyor design is included.

Jan 1, 2010

By B. M. Kunar

It is well known that job-related hazards and individual factors influence occupational injuries. However, research involving coalminers has been limited. This case-control study assessed the relationships of job-related hazards and individual/life style factors with injuries among underground coal miners. It compared 245 cases with at least one injury during the previous two-year period with 245 matched controls with no injury. The data were gathered via personal interview and analysed using the conditional logistic model. The significant risk factors were materials handling (adjusted OR 5.15), poor environmental/working conditions (2.63), geological/strata control-related hazards (2.35), lack of formal education (3.00), sleep disorders (1.86), alcohol consumption (2.32), disease (2.23), having a large family (5.40), and risk-taking behaviour (9.40). Machine-related hazards, sleep disorders and alcohol consumption primarily affected workers aged less than 45 years; whereas, environment/working condition-related hazards, presence of disease, smoking, risk-taking behaviour and large family size were more likely among workers aged 45 or over. Keywords: Occupational injuries, sleep disorders, job hazards, alcohol, coal miners

Jan 1, 2010

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010