Search Documents

By E. Taskin

Diasporic bauxite from the Mugla-Milas region was mechanically activated in a planetary mill for different activation times and the structural changes were examined by X-ray diffraction analysis (XRD), scanning electron microscopy (SEM) and specific surface area analysis (BET ? Burnauer, Emmett and Teller). Non-activated and activated bauxite samples were leached directly in alkaline (Na2O) solution at atmospheric conditions and the activation procedure led to the amorphization and structural disordering of the diasporic bauxite structure, which increased the dissolution efficiency. Effects of milling speed, liquid/bauxite ratio and leaching time on alumina extraction in direct alkaline leaching of diasporic bauxite were also studied. The alumina extraction was ~7% for non-activated bauxite and ~70% for activated (75 minute) bauxite. Key words: Diasporic bauxite, Mechanical activation, Alkaline leaching, Alumina extraction

Jan 1, 2009

By W. J. Miles

At the beginning of the 20th century, barite was a mineral of minor importance in the USA. Its primary use was to extend lead oxide in white paint. Barite also added the special qualities of hiding power and flatness to paint. Because white lead sometimes turns black or yellow and barite does not, ground barite became a pigment on its own merit. Barium chloride was added to bricks before firing to stop efflorescence when exposed to weather. Barium carbonate or nitrate added luster and brilliance to glass. Barium chemicals were added to refining sugar, enameling iron, making oilcloths and paper collars, and in the manufacture of paper, artificial ivory, rubber and lithopone. Lithopone became a major paint ingredient in the 1920s; its use lasted until the 1950s, peaking at 150,000 metric tons of barite in both 1937 and 1947 for the manufacture of lithopone. Later in the 20th century, titanium dioxide replaced lead oxide, barite and zinc oxide in the coatings industry. In the 21st century, barite is used as a filler, extender, or weighting agent in products such as paints, plastics, and rubber. Some specific uses include its use in brake and clutch pads for automobiles, automobile paint primer for metal protection and gloss, add weight to rubber mud flaps on trucks, and add weight to the cement jacket around petroleum pipelines under water. In the metals casting industry, barite is part of mold release compounds. Because barite significantly blocks X-ray and gamma ray emissions, it is used as aggregate in high density concrete for radiation shielding around x-ray units in hospitals, nuclear power plants, and university nuclear research facilities. Ultra-pure barite consumed as liquid is used as a contrast medium in medical X-ray examinations. Barite is the raw material for barium chemicals, such as barium carbonate, which is an ingredient in faceplate glass in the cathode-ray tubes of televisions and computer monitors. In the 21st century, barite industrial uses account for an estimated 78,000 tons per year in the United States. Another barite use was patented in 1926 by the oil industry. In this patent, barite is primarily used as a non-abrasive weighting agent for drilling for oil and gas exploration and production. As a weighting agent, it provides the downward force in a water based or oil based drilling fluid for cutting through rock with a tri-cone diamond drill bit. In order to minimize the wear on the drill bit and drill stem, minimum abrasion of the weighting agent is preferred. In recent years in the USA, 95% of the barite produced and about 80% on a world basis are used as a fluid weighting material during the search for oil and gas. During the latter part of the 20th century, barite was used in the drilling mud of oil and gas wells, particularly for wells deeper than 2000 meters, and petroleum well drilling demand for barite became the mineral?s major end use during economic expansions after World War II and subsequent increased use of oil and gas in the USA. The profitability of oil and gas production had a strong effect on the number of drill rigs and consumption of barite. The United States was the leading petroleum well drilling country starting in 1970, reaching 4,530 drill rigs in December 1981, and was the largest consumer of barite. In the USA, record highs of about 2.6 million tons of barite produced and 4.3 million tons consumed were reported in 1981. From 1997 to 2006, barite production declined from 662,000 to 589,000 metric tons. However, USA imports increased from 1,470,000 to 2,530,000 metric tons for lump barite. World production of barite increased from 6,780,000 to 7,960,000 metric tons during the same period. Table 1 (see Appendix) lists USA production, imports and exports and world production from 1997 to 2006. Major sources of imported barite include China, India and Morocco. Table 2 (see Appendix) lists the USA imports and price of barite by country. China, India and Morocco are the three largest exporters of barite to the USA and the world. Vietnam is a new producer, beginning in 2006. IMPACT OF CHINA ON DRILLING GRADE BARITE In the 1970s or before, China began supplying barite to the world drilling market in order to help develop their economy. When China first entered the barite export market, their high production volume, low pricing and low ocean transport expenses to the Gulf Coast forced barite producers in the USA to supply only regional markets, such as Battle Mountain Nevada barite for the western and Rocky Mountain states and Canada. Until recently, it was China?s government policy for domestic consumers to use barite below the API 4.20 specific gravity specification, leaving higher grades for export, but this is no longer the case. In recent years the internal demand for barite in China increased tremendously as their economy rapidly developed. China reduced their former 15% VAT tax rebates to 5% for Chinese barite producers, and then eliminated all VAT tax rebates on December 15, 2006. On the supply side, some high-grade barite deposits in China have been depleted. In particular, the low heavy metals sources are less plentiful. Additional mine capacity is being developed, but the new mines are underground and therefore costs will be higher. China?s appetite for other raw materials has tied up a large portion of the world?s bulk vessel fleet, including Panamax vessels (preferred for barite ore transport). Ocean transport freight rates have increased in recent years, and receiving ports in the USA are congested with imports of higher-added-value products. The Panamax Index, which tracks maritime shipping rates, more than doubled in 2006. China has also devalued its currency from RMB8.30 to RMB7.80 per dollar. These factors are driving up the import price of crude and ground barite for drilling. In addition, in the USA, rail congestion and high fuel prices led to higher trucking rates, increasing the delivered cost of ground barite to oil customers. India is the second largest supplier of crude barite to the USA and world drilling market. It produces all of its barite from a single deposit in the Cuddapah region of Andhra Pradesh State. More than 90% of production comes from the State-owned Andhra Pradesh Mineral Development Corp., and the government continues to closely control production, export volumes, and prices. India saw a dramatic increase in barite prices as a result of its last 3-year tender in 2004. However, in 2004 and 2005 their shipments of crude barite to the USA were not significant. In 2005, India began supplying barite pulverized to meet API specifications to the Gulf Coast. In 2006, Indian production was reduced owing to severe flooding in November 2005 that curtailed mining until mid-April 2006. Morocco has been the third largest supplier of crude barite to the USA and world drilling market. In 2003 and 2004 their shipments of crude barite to the USA were not significant. In 2005, Morocco resumed shipment of crude barite to the Gulf Coast and began supplying barite ground to meet API specifications to the Gulf Coast.

Jan 1, 2009

This paper is a collection of thoughts and frameworks. It addresses a simple question: æIf we are to believe the large number of people and institutions indicating that humans are destroying the Earth and that the end is nigh, why do we bother trying to be sustainable?Æ The paper lays out evidence for the existence of multiple hazards to global society. The existence of a hazard alone is insufficient to make an assessment of risk. Risk estimates are required to support decision-making. An approach to assessing risk is provided and some limited data are presented. A new ædefinitionÆ or statement of what sustainability (in a broad sense) might have become is then given. A decision framework for guiding decision- making about the risks is developed. This framework includes a definition of leadership with inherent implications for what determines whether a leadership position by title is actually leading. The paper concludes by offering a view of minerals industry sustainability and considerations around maturity in the current economic situation. It is hoped that by placing this collection of frameworks around sustainability, a supporting structure emerges that will facilitate action. It is proposed that action taken in this way will be more effective than reaction to regulation or even social license to operate imperatives because it is driven by a more holistic view of the challenges and the potential roles of individuals û all of whom are potential leaders at some scale of action.

Jan 1, 2009

By J. Rajala

The Kupol mill facility processed a high grade free milling gold/silver ore containing 28.2 g/t Au, 324.8 g/t Ag and approximately 0.5% pyrite during 2008 operation. Gold predominantly occurs a selectrum in the ore and silver is predominantly present in the forms of acanthite, stephanite, pyrargyrite and proustite. Mill start-up was in mid-May 2008 and the mill reached the design throughput of 3 000 tpd in October. The ore was ground to approximately 70%?53 microns. A Knelson Concentrator recovered 9.8% gold and 0.5% silver. The gravity tails reported to a cyanidation circuit that has 14 hours pretreatment and 116 hours leaching. The slurry from cyanidation was then processed by counter current decantation (CCD) thickening to wash and separate the leach residue from the pregnant leach solution. Precious metals are recovered fromthe pregnant solution using the Merrill-Crowe process. The washed CCD leach residue slurry is treated with calcium hypochlorite to destroy cyanide and then sent to the tailings impoundment. Leaching is performed with a new technology called ?CELP? (CANMET Enhanced Leach Process). The Kupol mill overall gold and silver recoveries for 2008 were 95.4% and 85.6% respectively, which were 2.8% and 7.5% higher than targets. Gold and silver extractions in the leach circuit were 94.2% and 84.5% respectively. Leach profiles indicated that gold extraction reached a plateau in the 4th tank while minor silver dissolution occurred in the 5th tank. With the CCD circuit included, total gold and silver extractions increased to 95.4% and 86.6%, respectively. Optimization of the leaching strategy made it possible to reduce sodium cyanide concentration to as low as 410 ppm without compromising precious metals extractions. Silver was effectively leached from the refractory silver minerals because CELP produced more oxidized mineral surface relative to the conventional cyanidation leached mineral surfaces. The average cyanide consumption for 2008 was 1.3 kg/t. The new leaching technology proved to be very robust and performed efficiently even with changes in feed grade and ore mineralogy. Laboratory experiments produced results that were indicative of plant performance. The robustness of the technology and the laboratory test work contributed to the success of the Kupol mill start-up.

Jan 1, 2009

By D R. Venkatesulu, N K. Nanda

Due to increased production of steel in India, the thrust is now on iron ore producers not only to enhance productivity from existing mines, but to look also into alternative resources, like lean grade iron ores such as banded haematite quartz (BHQ)/banded haematite jasper (BHJ), which are available in abundance but not yet utilised for want of suitable process technology. In this context, BHJ ore from the Bellary-Hospet sector was collected and subjected to detailed physical, chemical and mineralogical characterisation and beneficiation studies. The as-received sample was found to occur physically as alternating layers of haematite and jasper. The chemical analysis of the sample was 41.20 per cent Fe, 39.10 per cent SiO2 and 0.86 per cent Al2O3. Based on the mineralogical observation, haematite was found to be the lone ore mineral and jasper was the major gangue mineral. The microscopic observations revealed that the ore minerals liberate at a top size of 0.150 mm. Guided by the characterisation results, indicative tests were conducted using gravity and magnetic separation equipment, namely, Floatex«, gravity slime table and wet high intensity magnetic separator (WHIMS). The results indicate that it is possible to upgrade the sample by both gravity and magnetic separation techniques. However, the WHIMS results indicate that jasper grains report to the concentrate at higher gauss intensities. Therefore, based on the encouraging gravity separation results and the availability of new design spirals for treating fine particles, the applicability of gravity spirals for beneficiating BHJ in the liberation size range of -0.150 mm was studied. The sample was ground to a top size of 0.150 mm and was subjected to preconcentration using wash waterless spirals. Tests were conducted at different feed rates, pulp densities and splitter positions. The results indicate that it is possible to upgrade the sample from a feed grade of 41.20 per cent Fe to a preconcentrate ranging from 46 per cent to 62 per cent Fe with a yield ranging from 19 per cent to 55 per cent. The obtained preconcentrate was then subjected to a cleaning stage by using a combination of wash water and wash waterless spirals. The test results indicate that it is possible to obtain a final concentrate assaying 65.75 per cent Fe and 4.75 per cent SiO2 with a yield of 25.9 per cent and an iron recovery of 41.31 per cent. It was concluded that further test work is necessary to increase the recovery and improve the product specification.

Jan 1, 2009

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By R. B. Ngenda

The ?Kolwezi Zinc Plant?, in French ?Usines à Zinc de Kolwezi? (UZK), has produced about 910 000 dry metric tons of residues during the hydrometallurgical treatment of calcines from sulphide zinc concentrates. The zinc hydro plant residues contain on average 19.47% Zn, 2.7% Cu, 2.1% Pb, 26.6% Fe, 0.12% Cd, 0.39% As, 157ppm Ag, 447.8 ppm Ga, 475.4 ppm Ge, etc. This material was dumped in five ponds in the vicinity of the plant. The high Fe content in the ore concentrates induced important conversion of some of zinc and copper into ferrites during the roasting process. Those ferrites are very stable compounds, which are difficult to leach with dilute sulphuric acid solution. Therefore, they mainly report to the leaching residues. Hot leaching has been successfully applied to the treatment of zinc hydro plant residues. The method, however, presents the disadvantage of simultaneously dissolving iron(Fe). It is then necessary to remove an important iron quantity from solution prior to zinc and other metals recovery.

Jan 1, 2009

By Zhigang Liang

A carbon free precast block was prepared by using high-alumina fused corundum as aggregate and fused magnesia, and ultra-fine Al2O3 and ultra-fine SiO2 powders as matrix materials. A small linear expansion for the precast block was achieved through spinel formation from the reaction of MgO with Al2O3. The precast block showed a lower apparent porosity, higher hot modulus of rupture and better slag corrosion resistance compared to the traditional Al2O3-MgO-C brick. Moreover, the practical application of the precast block to the ladle lining proved it to possess a better thermal insulation which could effectively prevent the temperature drop of molten steel during the refining process. It can be predicted that the carbon free precast block could possibly be accepted as a new type of ladle lining material for the production of low-carbon and ultra-low-carbon steel.

Jan 1, 2009

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By C. Özgen Karacan

Methane emissions from the active face areas and from the fractured formations overlying the mined coalbed can affect safety and productivity in longwall mines. Since ventilation alone may not be sufficient to control the methane levels on a longwall operation, gob vent boreholes (GVB), horizontal and vertical drainage boreholes, and their combinations are drilled and used as supplementary methane control measures in many mines. However, in most cases, the types of degasification wellbores chosen are decided based on previous experiences without analyzing the different factors that may affect this decision. This study describes the development of an expert classification system used as a decision tool. It was built using a multilayer perceptron (MLP) type artificial neural network (ANN) structure. The ANN was trained using different geographical locations, longwall operation parameters, and coalbed characteristics as input and was tested to classify the output into four different selections, which are actual degasification designs that US longwall mines utilize. The ANN network selected no degasification, GVB, horizontal and GVB, and horizontal, vertical and GVB options with high accuracy. The results suggest that the model can be used as a decision tool for degasification system selection using site- and mine-specific conditions. Such a model can also be used as a screening tool to decide which degasification design should be investigated in detail with more complex numerical techniques.

Jan 1, 2009

By C. Guria

A modeling, simulation and optimization study of a complex industrial fluorspar beneficiation plant (Kadipani, Gujarat, India) with fourteen/ten flotation banks is carried out to find an optimum/near-optimum circuit for the given quality of feed ore. The phenomenological flotation model developed by Mehrotra and Kapur (1974) is used for circuit optimization. Two different optimization problems are formulated and solved. The first optimization problem involves a single objective function, which uses available plant data to estimate the feed-characterizing parameters, i.e., the flotation rate constants, by minimizing the weighted sum-of-square errors between the computed and plant values. The second optimization problem involves two objective functions to obtain several simplified circuits. The number of non-linking streams and the overall recovery of the concentrate, i.e., the acid-grade product, are maximized simultaneously in this problem. The single-objective variant (SGA-II-mJG) of the binary-coded elitist non-dominated sorting genetic algorithm with the jumping gene adaptation, NSGA-II-mJG, is used for the first problem, while NAGA-II-mJG (Guria et al., 2005 a) is used for the second problem. Simplified circuits with a few split streams are proposed on the basis of the present optimization study, which enhance the recovery of the acid-grade product without affecting its quality, for a given total volume of the flotation cell-bank. Even though the optimal solutions have certain drawbacks, they suggest a meaningful direction in using an iterative fitting of parameters to such optimal circuits, followed by re-optimization. Key words: Froth flotation, Mineral processing, Industrial fluorspar beneficiation, Feed identification, Circuit/network optimization, Global optimal, Jumping gene, Genetic algorithm, Multi-objective optimization

Jan 1, 2009

A sinter plant baghouse dust has been treated as a hazardous solid waste, and disposed at a very high price. A series of leaching tests were conducted to examine the possibility to produce high grade potassium chloride from the solid waste. It is found that around 40% of the solid wastes can dissolve into water, and a deposit with more than 90% KCl can be produced after simply drying the solution.

Jan 1, 2009

The largest investment in mining equipment in Caterpillar?s history ? The F series mechanical and electrical drive trucks ? is rapidly advancing. Caterpillar showcased the 793F and 797F mechanical drive trucks and the 795F ac electric drive truck at MinExpo in 2008 and have continued testing since then. The 793F and the 797F have accumulated more than 75,000 hours of field testing and have proven their performance capabilities and their durability. The new Cat C175 engine that powers them has racked up 130,000 hours of field testing in mining trucks and more than 120,000 hours in power systems. Because of the success of these field-follow programs, the 793F is targeted to go into full production within a few months and the 797F late this year. Caterpillar engineers have been testing two 795F ac prototypes at the Tucson Proving Grounds in Arizona. The development program has provided input for the construction of a new 795F ac in Decatur, IL. The new truck recently shipped to a copper mine in North America where it will serve as the first field-follow 795F ac as it works at the mine. The 313-t- (345-st-) capacity 795F ac will enter a new size class for Caterpillar, and, as a result, the primary focus of the Caterpillar ac electric program has been on the 795F ac. The commercial launch date will be defined as the field-follow program progresses. ?It?s fitting that soon after producing the 50,000th Cat off-highway truck, we are now shipping our first ultra-class ac electric drive truck to a mine,? said Chris Curfman, president of Caterpillar Global Mining. ?Our new trucks further solidify our position as the one manufacturer to provide unparalleled options and unmatched customer support.?

Jan 1, 2009

By Jared Ball, Benjamin Hogg

There are over 100 process parameters that can be monitored during a single Peirce-Smith (PS) converter batch operation. To support a consistent operation it is important to select the correct Key Performance Indicators (KPI’s) to monitor. They should be strategically chosen to drive the desired behaviour with enough flexibility to endure process variations. At the Xstrata Copper Smelter in Mount Isa most of the PS converter operators have very little experience and are often lacking in the appropriate education or training to properly understand the process. For this reason 10 simple KPI’s were chosen that could be easily comprehended and monitored by all smelter personnel. KPI compliance has been supported by relevant project work in the converter area. Charge sequence trials have been performed in an effort to reduce splash and optimise activity time. The online measurement of full and empty ladle weights has enabled an immediate indication of skull size, skim/slag carryover, and metal loss.

Jan 1, 2009

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, Nevada began large-scale production in 1977. During 2008 Round Mountain Gold Corporation (RMGC) relocated the primary crusher facility approximately 300 meters (1,000 feet) to make room for the next phase of open pit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17 meter (56 feet) high Mechanically Stabilized Embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, Colorado. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design, and construction of the MSE wall.

Jan 1, 2009

By S. V. Mkhatshwa

The purpose of the study was to investigate the factors which affect the performance of the loading and hauling fleet and also find possible solutions to eliminate these factors, so that the daily tonnages required could be produced .This is due to the high demand of manganese required by clients. The investigation strongly focuses on the performances of the three 777D Caterpillar trucks and the R984 C Liebherr Litronic Hydraulic Excavator. In the content of the study, these machines are used to remove and move the low grade manganese (also known as the top cut overburden) in order to expose the high grade manganese from north pit to dump 4. The objectives of the project were to determine the actual performance of the loading and hauling fleet per shift, compare the actual and the theoretical performance and identify areas that need to be improved. To achieve the goals set for the project, a number of activities were carried out. ?Perform a time study to compare the performance of the loading and hauling fleet with the manufacturer specifications ?Match the equipments analysis for Loading and hauling ?Road conditions analysis ?Rolling resistance and Road Gradients analysis ?Operating cost analysis.

Jan 1, 2009

The pyroclastic-filled Voorspoed kimberlite pipe has a low grade due to significant internal dilution which translates to a marginal business case. The site, with excavations, tailings dumps and buildings remnant of mining from 1906 to 1912 is to become De BeersÆ benchmark mine in South Africa. In a climate of skills shortages and lean structures, a geological service to optimise exploitation of this complex resource was established. As historical mining removed the higher-grade centre of the pipe, initial production was in the weathered upper benches along brecciated pipe margins. Trenching and blasthole logging before blasts helped to mitigate the effects of the drastic contact deviations that occur when working with an inferred geological model. However, identification of unfamiliar weathered kimberlite and delineation of unmodelled internal waste posed challenges. Efficient grade control by demarcation and allocation of individual truck loads will be vital to continue profitable mining at Voorspoed. Further challenges arose across disciplines. The first yearÆs planned production of mostly weathered kimberlite was processed through a plant designed for VoorspoedÆs unusually competent ore. The high clay content of the weathered material led to clogged chutes and overloaded fines disposal, hampering efforts to commission the plant. Resolving this problem involved mining æout of planÆ to provide a blend of fresh and weathered kimberlite. The calculation of an accurate mine call factor was hindered by a lack of haul truck monitoring, process stoppages and stockpiling in the plant during commissioning. Updating of the geological model to incorporate the contact changes observed in the pit was slowed by the need to first understand how 40 years of exploration data was integrated to create the model. A plan, involving focused mine geology practices, is in place to upgrade a portion of the resource from Inferred to Indicated level of confidence. These challenges are not limited to new mines but will be ongoing as new information is constantly gained at Voorspoed and many mining operations.

Jan 1, 2009

By B. Geelhoed

A generalization of Gy?s 1979 model for the variance of the fundamental sampling error has been proposed at WCSB2?2005 by Geelhoed. This generalized model can potentially lead to a better correspondence with actual sampling processes. However, a new parameter is required by the new model: ?the parameter for the dependent selection of particles?(Cij). It is important that this new parameter, which is at the basis of the new theory, is well understood in the sampling and blending community. In order to clarify the meaning of Cijand to prevent potential misinterpretation of Cij, we discuss the difference between Cij and an intuitively associated, but different, parameter: ?the parameter for the dependent selection of particle types?(Mij). In this contribution, the theoretical difference between both parameters is clarified. Simulations demonstrate that, numerically, the difference between Cij and Mij can be large. Some additional advantages of the approach which uses Cij are discussed: (i) the approach based on Cijis more general; (ii) in all cases where Mij is known, Cij can be determined as well, while the reverse is not true; (iii) an equation already exists that relates the sample variance to the value of Cij.

Jan 1, 2009

By G. Danko

MULTIFLUX, a new thermal, hydrologic, and airflow model and software is being developed to solve the flow of heat, moisture, and air in and around an underground opening. MULTIFLUX couples two distinct domains that are solved separately first and re-coupled as an iterative task: (1) the rockmass, and (2) the airway. The airway is solved with a lumped-parameter Computational Fluid Dynamic (CFD) module which is an embedded part of the MULTIFLUX code. The CFD model includes convection, conduction, and radiation for heat, as well as convection and diffusion for moisture transport in an air-filled opening. The CFD model also solves for the airflow field. The surrounding rockmass model may be from any analytical solution, or from a complex thermal-hydrologic numerical model such as NUFT or TOUGH2. The rockmass model is interfaced to MULTIFLUX using a novel technique called Numerical Transport Code Functionalization (NTCF). The method provides fast convergence on a personal computer platform. The paper reports the results of MULTIFLUX simulations for a mine drift, comparing calculations with a known mine climate software, CLIMSIM, and with measured data. Through this validation example, the performance of MULTIFLUX is demonstrated. The results show excellent agreement due to the use of realistic modeling assumptions and boundary conditions.

Jan 1, 2009

By K. L. Lownie

For research and test data to serve a useful purpose, it is essential that it be derived from some known standard test procedure that allows for comparative analysis as well as independent replication and verification. Fan performance data provided by manufacturers is not absolute, and is influenced by the geometry of the test installation. For these reasons, fan test standards have been prepared in order to establish a clearly defined test procedure that allows for comparison of different fan designs, and also allows for the independent verification of test data. Internationally recognized Standards such as BS848, ISO5801, and AMCA 210 etc. are highly prescriptive, and precisely specify test duct configurations, measurement procedures, measurement planes and instrumentation to be used. Provided the laboratory tests are conducted strictly in accordance with the relevant Standard, the performance data will accurately reflect fan performance within the appropriate tolerances for efficiency, pressure and flow when tested in the defined configuration. Major differences in performance exist between a fan tested in accordance with a Fan Test Standard, and an identical fan installed in a mine ventilation system. The aerodynamic performance of any fan will be influenced by the quality of the fan manufacture, the flow system within which it is operating, the location of measurement planes, and the system stability. The flow distributions present in a standardized Laboratory test are unlikely to be repeated in mine ventilation systems, and this will also disadvantage fan performance. Unless the fan supplier takes all of these influences into account, there will an inevitable reduction in fan aerodynamic performance, and the end user will experience a shortfall in expected flow through the mine. The effect on fan performance can range from minor inconvenience to catastrophic fan failure resulting in major rectification costs and significant loss of mine production.

Jan 1, 2009