Search Documents

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

By M. K. Sichone

Anglo Platinum?s Waterval smelting complex based in South Africa operates the Anglo Converting Process (ACP) that produces SO2 offgas. This SO2 offgas is treated in a double-contact, double-absorption acid plant allowing for conversion efficiencies higher than 99.90 %. The catalytic converter used in the acid plant to convert the SO2 to SO3 is a 4-bed reactor loaded with a combination of cesium-promoted and conventional vanadium pentoxide catalysts. In June 2008 there was a shutdown, in which one of the main activities was to screen the catalyst. Before this shutdown, the operator would control the converter pass temperatures manually, via the SCADA, especially during plant start-ups after which some of the automatic temperature controllers were used. After the shutdown, the control philosophy was revisited and all temperature controllers were put on auto mode during plant start up. Furthermore the set points of the pass inlet temperatures were reduced to maximize conversion in the first two passes. The result has been a reduction of SO2 emissions, from a daily average of 50 ? 70 ppm to as low as 20 ppm for similar sulphur dioxide and oxygen concentrations. Further work has been done to maintain high bed temperatures in the third and fourth passes at low SO2 strengths by splitting the gas stream between pass 1 and 2 thus increasing the SO2 content in the gas to pass 2. This increases the temperature of the gas exiting the second pass, which results in higher temperatures in passes 3 and 4. Comparison of the converter performance prior to and after the changes is made. The benefits of partially bypassing the first pass to increase the SO2 content in the gas to the second pass are shown. Conclusions and scope for further work have been drawn from the comparisons.

Jan 1, 2009

By Jessica Smith

Jan 1, 2009

By T. Könighofer

Processing of copper-cobalt orebodies in Africa?s Copper Belt has received much recent attention with various flowsheet options being developed specifically for the refining of cobalt. The upfront leach and copper refining routes are well understood whereas the refining of cobalt is more complex, requiring numerous impurity removal steps to produce high purity metal. This paper describes an investigation into one of the possible processing steps in the refining of cobalt, namely, cobalt solvent extraction. The paper emphasizes the importance of upstream impurity removal to achieve the required cobalt solvent extraction feed composition. 18% (v/v) Cyanex 272 in an aliphatic diluents is used as the organic phase. The pH profiles in the various stages are evaluated in order to obtain a raffinate containing <10mg/l cobalt and with a low magnesium content reporting to the stripping section. The pH profile is also used to minimize the impurity deportment to the cobalt electrolyte. The effect of adding a pre-neutralization stage before feeding the organic phase to the extraction circuit is investigated. Zinc build-up in the stripping stages is also looked at. It is recommended for the purpose of this study that four extraction stages at an O:A ratio of 1 with a pH profile from 4.9 to 5.7 be employed. The pH is controlled with 40g/l NaOH. A pre-neutralization stage is required, where the organic phase is contacted with 10 M NaOH. Two scrubbing stages are recommended at an O:A ratio of 40, using the cobalt electrowinning advance electrolyte as the scrub liquor. Three strip stages are to be employed at an O:A ratio of 0.67.

Jan 1, 2009

By David Tisdale, Phillip Mackey, Nagendra Tripathi, Matthew Kreuh, Pascal Coursol

Xstrata Nickel’s Sudbury smelter operation is based on fluid bed roasting of Ni-Cu sulphide concentrate, followed by electric furnace reductive smelting and Peirce-Smith converting to produce a Bessemer matte for electro refining, along with sulphuric acid produced from smelter gas. While the site dates back to the 1930s, the present smelter configuration has been operational since 1978, and currently has a nominal capacity of about 67,000 tpy of contained nickel and is investigating options to expand in future up to 85,000 tpy. As part of a review of plant capacity options, a new metallurgical model of the plant was developed in order to examine a number of processing alternatives. Based on the METSIM™ platform, the present model includes the ability to examine the impact of a number of plant parameters on potential plant performance including; for example, the following: percent of sulphur elimination in roasting, matte grade, degree of matte metallization, temperature, coke requirements, sulphuric acid production, CO2 emissions and overall energy requirements. The process model also includes a number of special features adopted; for example, approaches to effectively model the complex Ni-Cu-Co-Fe-S-O matte system. This paper provides a description of the model and gives an overview of the results. As well as presenting the results of the present study, the applicability of this modeling approach to pyrometallurgical systems in general is also briefly discussed in the paper.

Jan 1, 2009

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Bob Burnham

Agenda 1 Overview of forecasting process 2 Review of Pre and Post Recession Forecasts 3 US Demand/Supply Summary 4 Coal Demand by Region 5 Coal Distribution by Census Region 6 Coal Price Outlook 7 Carbon Cases 8 Takeaways

Jan 1, 2009

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, whereas in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600?1000°C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed. For over 60 years, Outotec has progressively been developing the principle of fluidized bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidized bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

Amid some of the worst economic conditions that the mining industry has been faced with in more than a decade, the mood among the large crowd at the 114th Annual Northwest Mining Association?s annual meeting was surprisingly upbeat. More than 2,200 attendees showed up at John Asuaga?s Golden Nugget Casino in Reno, NV for the conference held Dec. 1-5. And more than 200 companies exhibited in 240 spaces, including SME and the Minerals Information Institute. The number of attendees and exhibitors were the most for the conference in more than 10 years. The conference was held in Reno/Sparks for just the second time in its illustrious history but began under the cloud of global financial turmoil. Prior to, and during the conference, the industry news headlines were grim, to say the least. An alarming number of mine plans and expansions had been put on hold; hundreds of miners across the United States had been or were in the process of being laid off; commodity prices were falling and some of the biggest mergers in the industry fell through while miners around the world put the brakes on to take a wait-and-see approach. It was a painful time for many, but the downsizing actions taken by many mining companies was exactly what needed to happen, according to Industry Outlook Luncheon featured speaker Frederick Sturm. He is the executive vice president and chief investment strategist and member of Mackenzie?s Investment team. He has earned a reputation as one of Canada?s leading investors in natural-based companies and he also manages the Ivy Global Natural Resource Fund in the United States Sturm said that the mining industry has fallen hard and that he expects it to bounce back quickly, before falling hard again. In these tough times, he said, the companies that have pulled back on production early are doing the right thing in the long run.

Jan 1, 2009

By Braam Blom

PK2 Ventilation shaft is part of Paardekraal No 2 twin shaft system that is being developed to replace depleting Merensky reef production at Paardekraal shaft complex. The sinking team at this shaft faced considerable challenge of improving the total sinking cycle in order to be able to deliver the fully equipped shaft on time and on schedule. The cladding support cycle was identified as the tedious and time consuming activity in the overall shaft sinking operation. Reduction in the time required for handling and setting up the support installation equipment, and the time required for subsequent installation of the necessary support has a direct impact on the overall cycle time, and consequently the overall productivity and efficiency of the sinking operation. This reduction in support cycle was achieved by making use of machine carousel. The objective of this paper is to describe the support methodology that was used during the ventilation shaft sinking and the use of the machine carousel to reduce the cladding support cycle. The machine carousel replaces the traditional use of machine kibble in conventional vertical shaft sinking and has been designed specifically for installation of sidewall support at the shaft bottom during the sinking process.

Jan 1, 2009

By M. Helm

Over the last 40 years, numerous investigations have focussed on the preg-robbing capacity of carbonaceous material during gold ore processing. Various techniques have been applied to characterize the physical and chemical properties of the carbonaceous material in efforts to predict its preg-robbing capacity. The present study, which forms part of an ongoing investigation, is specifically designed to increase the understanding of preg-robbing in ores containing carbonaceous material. In excess of 100 samples from 13 gold mines located in major gold provinces of the world have been incorporated into the present study. These samples were characterized using industry standard metallurgical techniques and were shown to have gold adsorption capacities ranging from a few grams to many hundreds of grams of gold per ton of ore. Further analysis showed that the crystalline nature of the carbonaceous material, which is related to its geological history, is important in determining the preg-robbing capacity of an ore. This finding builds on the common understanding that the preg-robbing behaviour of an ore is related to the amount (or abundance) of carbonaceous material present in that ore. In this study, Raman spectroscopy was used to evaluate the physical nature of carbonaceous material. This is a tool which has been successfully applied by researchers for the characterisation of carbon materials, with respect to crystallite size and lattice defects. Raman analysis of the samples included in this study showed varying degrees of disorder in the carbonaceous materials from the different deposits. Comparison of the Raman spectra with the gold loading capacities of the samples indicated a direct relationship between the structure of the carbonaceous material and its capacity to preg-rob gold. From this, a simple and robust method has been developed based on the Raman spectra of the sample and carbonaceous material content to predict the preg-robbing capacity of an ore. The potential exists to develop a predictive tool using Raman spectroscopy for characterising the preg-robbing capacity of an ore. Such a tool would have potential application in projects ranging from the early stage of exploration through to more detailed feasibility studies and mining operations. The result of applying the predictive method outlined in this paper would be the effective and proactive management of the deleterious influence of carbonaceous material on gold recovery in mining operations.

Jan 1, 2009

By S D. Golding, K Baublys, V Nanjappa, C J. Moran

Water reuse is becoming an integral component of the water management strategy on mine sites. This practise is being driven by corporate sustainability goals, community and societal pressures to demonstrate improved water stewardship, as well as climate and regulatory pressures. However, water reuse often results in water quality compromise which can then result in decreased recovery through problems in processing circuits, product quality, and an increased likelihood of discharge of water that cannot meet environmental regulatory requirements. On most mine sites, there is usually a disjuncture between water quantity management and water quality management with the latter being managed solely as an environmental problem. It is becoming increasingly clear that water quality and quantity must be managed as an integrated system. In order to integrate water quality and quantity management to achieve multiple objectives the dynamics of water and constituents must be understood. Using examples from a study being conducted at a coal mine in the Bowen Basin, this paper will outline the dynamics of water and salts on the site.

Jan 1, 2009

By D. M. Walters

To achieve safe and healthy working conditions in shaft sinking operations, ventilation, and where necessary cooling, must be provided. These requirements are considered for sinking vertical, sub-vertical and decline shafts. Regulatory requirements, determining air volumes and amount of cooling required, the various ventilation methods used such as force, exhaust, twin columns, air reversal using four gate systems and the equipment required to achieve this, are discussed. Consideration is also given to the sinking of single and twin declines using diesel equipment, calculating the air volumes required to dilute pollutants and the various methods for achieving this. Also discussed is the importance of having early ventilation design input to the overall design of the mine. In many cases ventilation can be the prime determinant for the size and configuration of the shafts or declines that have to be sunk.

Jan 1, 2009

By Z Tong, M Gao, X Wang

In response to the need for improved magnetic separators for beneficiation of fine grained iron ores that have been finely ground to liberate the iron minerals from the gangue, a series of high efficiency wet drum permanent magnetic separators (T-GCT) has been developed by Maanshan Tiangong Technology Co Ltd. These magnetic separators have high efficiency for separating superfine strongly magnetic minerals and the ability to produce high-grade concentrates with high recovery. They are ideal replacements for conventional drum magnetic separators, especially for treating superfine particles.

Jan 1, 2009

By Will Jansen

When Enron rocked the United States with its Titanic-sized financial accounting scandal, miners and metallurgists were probably too busy on the mine sites in remote locations to wonder about its ripple effect. But then Enron sank, Arthur Andersen tanked and the list of scandals, costing billions of dollars, continued to ripple. Followed by the Public Company Accounting Reform and Investor Protection Act of 2002 (Sarbanes-Oxley), the recent credit crunch and weak economy, the currents from Enron?s collapse eventually washed right into the mine and the mill. These events placed intense scrutiny on metals production accounting processes as traditional semi-qualitative metal accounting practices provided insufficient credibility and transparency. ?There is growing intolerance of organizations that are unsure about the location of thousands of tonnes of ore, which will typically lose 10 to 15% of their notional value on the way to the concentrator,? Rob Morrison wrote in the opening chapter to An Introduction to Metal Accounting and Balancing. ?If the measurement and forecasts also contain qualitative (fudge) factors, a very real suspicion might emerge about just how much metal might disappear (by theft or misplacement) before detection becomes likely.? Metallurgical accounting, put simply, is the tracking and reporting of the quantity and quality (tonnage and grade, usually) of materials entering or leaving each stage from source to product for a specified accounting period. Lacking an accounting standard, metals accounting in precious metal operations has been performed in an ad-hoc, informal manner, leading to numerous errors and unidentified potentially significant inefficiencies and financial losses. As a result, mining companies are beginning to examine the quality of their metals accounting systems since they form the basis of mining company?s financial accounts and reports. As part of an effort to create that accounting standard in the mineral industry, University of Queensland?s Julius Kruttschnitt Mineral Research Centre published the textbook An Introduction to Metal Accounting and Balancing in 2009. While development of a textbook and standard are significant steps forward, the challenge in the precious metals industry is in the application of some of these suggested practices. Though improving process transparency and precious metals accounting reporting accuracy is a key driver for change from the financial side, perhaps even more important is the potential benefit to operational performance that comes with better measurement, accounting and reconciliation systems. Loss of precious metals, processing of waste and inefficient mining and processing systems are all problems that are faced in an operation on a daily basis that can help be resolved through improvements in metal accounting and reconciliation. The financial consequences of such operational inefficiencies and bad decisions based on poor information are arguably greater than consequences of fraudulent accounting. Large discrepancies between mine and mill measurement systems that measure the quantity and quality of valuable material currently exist. Some of these are expected because of statistical variation, but inherent random measurement variation is sometimes an insufficient explanation. Though the mill can usually make much better production estimates through their measurement systems (that is, less variation), this knowledge rarely benefits the mine. 3 Moreover, even if the mine does a reasonably good job of estimating expected production at the grade control level (in situ), issues such as blast movement, poor mining practice and inefficient ore/waste classification make for a disconnect between the in situ estimates of the mine and the estimates from the concentrator. This inhibits effective evaluation of the reserve and grade control models using concentrator estimates. Linking the two ends, mining and concentration, is a neglected area sorely in need of an overhaul. Hence the need for improved mine to mill reconciliation ? the area of comparing, balancing and adjusting production estimates between mine and mill for consistency in reporting.

Jan 1, 2009

By P Mesquita, A Nolan

Using a scientific-principled definition of global socio-ecological sustainability can be a useful basis for planning precious and base metal mining projects. The mining industry faces key challenges of; viability of the minerals industry; the control, use and management of land; national and local socio-economic development; environmental management; materials stewardship; and access to information. Using a framework for strategic sustainable development to assess the current reality of mine project development has resulted in identifying areas of strength and opportunities for improvement between current best practices and a desired vision of sustainability constrained by science based principles. These gaps indicate opportunities to strengthen current strategies, tools, and actions with a deeper understanding of socio-ecologic systems and a first-order, principled definition of sustainability, enabling success in moving towards achieving a sustainable society, ie sustainability. Evaluation of mine project development and their impacts on ecological and social systems using a systems perspective which recognises the underlying principles of operation, delays, feedback loops and response to change highlight specific opportunities to create value for social, economic and ecologic systems. Envisioning this future for mining projects within a sustainable society can be done by evaluating their development and operations guided by the sustainability principles. Performance indicators play a key role in measuring progress towards achieving sustainability goals yet it is necessary to consider whether indicators capture the whole systems perspective. Connected to this broader view, indicators can contribute much value to the mining industryÆs sustainability journey. This paper examines how current processes for mining projects can be developed using a whole systems perspective and measured using holistically designed performance indicators.

Jan 1, 2009

By Khaled Morsy

Cementitious seals are made of foamed cements with strength ranging from 100 to 600 psi. These cementitious seals are usually used at locations where the seal will be subjected to some convergence, assuming that this material can absorb entry closure without compromising the structural integrity of the seal. Prior to 2006, Lake Lynn Experimental Mine (LLEM) conducted full-scale tests on various cementitious seals designed to meet or exceed the 20-psi horizontal static load requirements of the old 30 CFR1 75.335. Both hydrostatic and dynamic loading tests were conducted. The structural response (pressure and displacement readings) obtained from these tests were recorded. The stability of the cementitious seal is based on balancing the load applied to the face of the seal from the explosion against the shearing resistance at the seal/rock interface. Therefore, the properties of the seal/rock interface, such as stiffness, cohesion, friction, etc. are critical to determine the stability of a cementitious seal. These properties are usually assumed by the researchers in their models. This paper emphasizes the importance of having the correct properties of seal/rock interface in the numerical modeling. FLAC 3D models were developed to simulate Celuseal2 cementitious seals subjected to both hydrostatic and dynamic loadings. Using the hydrostatic and dynamic loading test data conducted at LLEM, the static and dynamic properties of the seal/rock interface were back calculated. The FLAC 3D models showed good agreement with the test results.

Jan 1, 2009

By C. R. Hairfield

With ever rising energy costs, it is increasingly important for mines to operate with energy efficiency. As a large portion of a mine?s energy consumption is often attributed to the operation of mine ventilation fans, maintaining an efficient ventilation system is a critical pro-active way for mining companies to reduce power costs. A common way to measure a mine?s ventilation system efficiency is to calculate the volumetric efficiency, which is simply a calculation of the percentage of total mine air that is usefully employed for production. The purpose of this study is to document a nationwide comparison of the volumetric efficiency of U.S. underground coal mining operations. The results will aim to show just how efficient today?s coal mine ventilation systems are and what factors may be causing their various efficiencies and inefficiencies.

Jan 1, 2009

By M Kozikowski

The primary purpose of these investigations is to determine dewatering requirements and likely impacts associated with mining operations. Standard aquifer testing techniques were carried out at multiple locations within the Ord Range near Pardoo, Western Australia. Aquifer properties of an oxidised haematite orebody were calculated from test pumping data conducted in five fully penetrating test bores. Hydraulic properties of the Ridley magnetite orebody were calculated based on short term constant rate pumping tests, and packer tests. Packer tests were conducted in undeveloped and uncased exploration holes and diamond core holes. The new data sheds light on the hydrogeological properties of this previously unexplored region of Western Australia.Aquifer testing procedures for each bore included a preliminary step test followed by a constant rate test. Recovery data were collected in each bore over a period of four to six hours. Prior to testing, background water levels and water samples were collected in a network of monitoring and exploration bores to establish baseline water levels, gradients and water quality. Water quality within the bedrock of the Ord Range varies from 2000 to 5500 mg/L TDS whereas water quality within the alluvial sequence of the De Grey River is highly variable (400 to 2500 mg/L TDS), but is predominantly brackish with some water of potable quality which is used to supply Port Hedland. Test pumping supports the conceptual hydrogeological model that consists of a pod like orebody (aquifer) surrounded by low permeability waste rock (BIF), with very weak hydraulic connection to the adjacent alluvial systems. Calculated hydraulic conductivity from test pumping data across Pardoo ranged from 0.01 to 59 m/d, depending on deposit tested.A groundwater model was used to simulate dewatering required in proposed pits and to estimate the impact of dewatering on the surrounding shallow alluvial aquifers. Test pumping and numerical groundwater flow modelling indicate the proposed below water table pits can be successfully dewatered utilising in pit dewatering production bores. Yields from individual dewatering bores will reduce with time due to the reduction in saturated aquifer thickness.Based on the numerical groundwater modelling and field investigations the likely impacts to the adjacent De Grey River alluvial aquifer system (within the Priority 1 De Grey River Water Reserve) resulting from mining and dewatering activities is considered minimal. Recalibration of the groundwater model will be undertaken once several months of dewatering data are available.The aim of this paper is to present a range of aquifer parameters derived through standard aquifer testing techniques for an area previously unexplored in terms of hydrogeological characteristics. It is the goal of the authors to provide this comparison data set for future work in similar geologic media.

Jan 1, 2009

By S. A. Shipilov

In this paper, the annual direct cost of corrosion in Canada is estimated to be approximately $41 billion. The figure does not include the indirect (user) costs of corrosion, sometimes referred to as social costs, which would essentially double the amount. Also, corrosion is shown to be a major contributor to environmental pollution, including when it results in the leakage of hazardous materials from pipelines, vessels and nuclear reactors. Industrial accidents caused by corrosion kill and injure hundreds of people annually. At present, corrosion is at the core of safety and risk analysis in several major industries such as energy generation, oil/gas production and transportation, chemical processing and petroleum refining. With the recent steam pipeline explosion during rush hour in New York killing one man, the collapse of the bridge in Minneapolis killing 13 people and another two years ago in Montreal when 5 people were killed, infrastructure corrosion is increasingly being acknowledged as a public safety concern.

Jan 1, 2009