Search Documents

By P. Beukes, D. Bessinger, R. Glenewinkel

High titania slag is produced by the smelting of ilmenite and a suitable carbonaceous reductant in electric furnaces. Currently liquid slag is cast into large blocks, which take about 10 days to cool down before they can be crushed, milled and classified into two final products. The two products, chloride and sulphate grade slag, are differentiated according to their size. Granulation of titania slag has been identified as a possible alternative to the conventional block route. This paper discusses some of the work carried out at Exxaro Research and Development to investigate both wet and dry granulation of titania slag.

Jan 1, 2007

By U. Martin

Advanced copper materials for conducting applications require an optimal combination of high mechanical strength at ambient and moderately elevated temperatures together with superior electrical and thermal conductivity. Mechanical alloying under repeated cooling of the milling vials in liquid nitrogen has been applied to produce ultra-fine grained (UFG) oxide dispersion strengthened (ODS) copper with a high yield strength at ambient temperature. In the present study ODS copper was manufactured by mechanical alloying of copper powder and 3% by volume of incoherent oxide dispersoids. During the high-energy milling a homogeneous distribution of fine dispersoid particles (diameter nearly 100 nm) can be achieved in the powder. Samples with a density of more then 97% of theoretical value were produced by uniaxial hot pressing under 650 MPa at 600°C for 20 minutes. The high yield strength at ambient temperature can be described by a linear superposition of the Orowan stress for particle hardening and of ultra-fine grain strengthening according to the Hall-Petch mechanism. Simultaneously, a best value of 75% IACS could be obtained for the electrical conductivity. The creep behaviour of ODS copper in the temperature range from 500°C to 700°C is described within the frame of diffusional creep deformation.

Jan 1, 2007

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

By R. G. Gillies

The pipeline transport of paste, backfill or thickened tailings slurries is an important component of the tailings disposal process in many mines around the world. These mixtures contain significant fractions of fine (clay) and coarse (sand) particles, causing them to exhibit non-Newtonian flow behaviour and high frictional pressure gradients. There is often economic incentive to operate these pipelines in the laminar flow regime. Irrefutable evidence has shown that coarse particle settling can occur during the laminar flow of these slurries even when static settling tests show no indication of such behaviour. Previously, a ?rule-of-thumb? minimum frictional pressure gradient of ~1.5 to 2 kPa/m was suggested to ensure effective sand transport, based on the results of tests conducted using viscous Newtonian oils. In this paper, we examine the results of laminar flow tests of non-Newtonian, coarse-particle laden slurries conducted with pipeline loops of 50, 100, 150 and 250 mm in diameter. The results indicate that the ratio of the mean wall shear stress to the mean surficial particle stress is a better indicator of laminar flow settling tendency than frictional pressure gradient.

Jan 1, 2007

By D. G. Sediako

Chemical composition and the casting/rolling production routes determine the cost and properties of the wrought material. For example, the coarse-grained structure frequently associated with DC casting requires complex rolling schedules to refine the grain size. Hot forming (rolling/forging/extrusion) results in a strong crystallographic texture, which is responsible for the tension-compression strength asymmetry frequently exhibited by magnesium alloys. Understanding the influence of alloy composition on texture evolution during forming provides useful practical information to optimize industrial hot-forming technologies for magnesium alloys. In this study, a series of Mg-based alloys containing varying combinations of Al, Rare Earths, Zn, Ca, and Sr were subjected to identical casting and extrusion processes in order to isolate the effects of alloy composition on texture evolution. Textures were measured by neutron diffraction at the NRC Canadian Neutron Beam Centre. The ability of neutrons to penetrate deeply into materials allowed information to be retrieved from all regions of the bulk specimens without destructive and time-consuming sectioning operations, thereby providing true bulk texture data. {1010} , (0002), {1011}, and {1012} pole figures were generated for all of the as-processed alloys, from which Orientation Density Functions were obtained. The were then used to reconstruct the pole figures and to extract semi-quantitative texture data showing how the (0002) and {1010} planes align themselves with respect to the extrusion axis. It was found that varying the concentration of aluminum (3-4 wt%) and Rare Earths (2-3 wt%) in AE alloys had a weak effect on texture development. All of the alloys showed similar magnesium extrusion textures, in which the (0002) poles align themselves preferentially with the extrusion axis. The substitution of Sr for Rare Earths also did not have a significant impact on texture development. On the other hand, while the presence of small amounts of Zn and Rare Earths did not have a strong effect on texture development, alloys with higher concentrations of these alloying additions (in combination) showed an enhanced tendency for the {1010} poles to align themselves with the extrusion axis. The addition of Ca also enhanced the alignment of the {1010} poles with the extrusion axis. These textures can complicate further processing and introduce a significant anisotropy that could influence creep properties.

Jan 1, 2007

By S. Asokan, CVGK Murty, R. Upadhyay

The principal mineral sources of titanium are rutile, anatase (both TiO2), ilmenite (FeTiO3) and leucoxene (a weathered ilmenite of variable concentration of TiO2 but similar to pseudorutile Fe2Ti3O9). These titaniferous minerals along with their value added products like Synthetic Rutile and TiO2 slag constitute ?Titanium Feed-stocks? for TiO2 pigment, Ti metal and welding electrodes industries. Unlike in other industries, the demand driver for titanium minerals is not the metal, but the TiO2 pigment ?a specialty chemical. Of the total titanium feedstocks usage in the world, about 93 % is consumed in TiO2pigment, with only about 3 % is utilized in metal production. India?s heavy mineral sands resources are among the largest and also one of the richest grades in the world. The country?s Ilmenite resource base stands at 348 million tonnes of Ilmenite (18% of the total world reserves)along with 18 million tonnes of Rutile, 21 million tonnes of Zircon, 8 million tonnes of Monazite, 107 million tonnes of Garnet and 107 million tonnes of Sillimanite. Though the grades (Total Heavy Minerals (THM) present in the sand) of Indian deposits are relatively rich, the contained ilmenite are termed as sulphate grade with 50-53% TiO2 (Chavra deposit of Kerala and Ratangiri deposit of Maharastra are an exception with 60% of TiO2). While superior grades with adequate reserves lead to a cost advantage in ilmenite production, the lower TiO2 percentage allows the direct use of Indian ilmenite only in the production of TiO2 pigment through sulphate route and for the chloride pigment production; such ilmenite is required to be upgraded either to Synthetic Rutile (SR) or TiO2 slag. However, in order to produce TiO2 slag in India at a globally competitive cost, the issues like high power tariff, inadequate infrastructure, expensive logistics, less enthusiastic market preferences, supply-demand gaps are to be adequately addressed. This paper deals with some of the above issues and possible solutions thereto in production of TiO2 slag from Indian ilmenite.

Jan 1, 2007

How did you get into mining; were you from a mining town or mining family? Not at all. I grew up in northwest Kansas. I liked to hunt and fish, so I thought it would be fun to work for a company that made knives or guns. It seemed like metallurgical engineers would be something those companies could use, so I started in physical metallurgy. I got a summer job at the great Climax molybdenum mine near Leadville, CO shoveling muck onto conveyors. I was hooked. I loved everything about mining, so in the fall, I changed majors from physical metallurgy to mineral processing. For many years you actually discouraged young people from studying the mining disciplines. Could that be right? That’s true.

Jan 1, 2007

By R. ZapataN.

"In the following report, Altonorte Smelter owned by Xstrata will explain its experience with its denominated furnace called ""Continuous Altonorte Reactor"" since started up in March 2002. The Reactor is the main and only smelting furnace since the operation of Reverb Furnace was stopped (15 days after the start up of the Reactor) and it can be operate with dry concentrate for injection by tuyere and wet concentrated via Garr Gun when the injection system fails. From the started up of the Reactor, three operational campaigns have been carried out where in each one they have been increased their smelting throughput and availability. The flexibility reached by the technology bath smelting has allowed a high level of smelting of concentrate and revert materials. The high availability of the Reactor and overcoming problems that were considered of high complexity like the extraction of white metal and slag, refractory campaign, etc. has allowed the Altonorte smelter to project to smelting 1,200,000 tonnes per year with its only Reactor in next year."

Jan 1, 2007

By M. Perolo, A. Contini, E. Ramelli, G. Borgonovo, L. Locatelli

This paper presents the ground settlement monitoring system used during the construction of two tunnels bored by two EPB TBMs, beneath the existing and active railway embankment in Bologna (Italy). The tunnels run close to large buildings and beneath bridges and other infrastructure. Data are collected from remote total stations and from electro levels installed directly on the railway tracks. The automated monitoring system acquires and analyses data then sounds an alarm in the event that there is a problem. Alarms are sent out in case of excessive tilt or settlement. Data is provided through a dedicated web application for multiple-party access, to gather, manage and store monitoring data.

Jan 1, 2007

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007

By D. F. Malan

This paper presents an overview of work conducted over several years to investigate the continuous stope closure profiles recorded in tabular excavations and the use of this data as a hazard indicator. In spite of the brittle nature of the rock, measurements in gold mines and intermediate depth platinum mines revealed a significant time-dependent closure component. Various approaches to simulate the time-dependent closure have been investigated. Viscoelastic theory is able to simulate the time-dependent closure behaviour, but there are subtle problems with the use of this theory as it cannot simulate the failure processes in the rock. To overcome these problems, continuum and discontinuum elasto-viscoplastic models were developed by the authors. Discontinuum models have the advantage of being able to simulate the creep behaviour of prominent discontinuities. Development of these models has led to useful insights into rock mass deformation and has made the numerical simulation of parameters, such as rate of mining, possible for the first time. A number of practical applications for the mining industry have been developed from this study. Among these are the delineation of geotechnical areas using closure data, use of the data as a hazard indicator and to give warning of large collapses in the platinum mines, identification of areas to be preconditioned in the gold mines, measurement of the effectiveness of preconditioning and improved da

Jan 1, 2007

By John J. Sammarco

Miners depend most heavily on visual cues to recognize underground mining hazards; consequently, illumination plays a critical role in miners? safety. Some hazards are located in the miners? peripheral field-of-view (10 degrees to about 60 degrees off-axis) or on-axis (0 degrees). The objective of this research was to determine if there were visual performance improvements when using solid-state cap lamps with light-emitting diodes (LEDs) as compared to incandescent light bulbs commonly used in miner cap lamps. Recent research has indicated that an increased short-wavelength content of the spectral power distribution of LEDs relative to incandescent lamps improves peripheral visual performance for low-light (mesopic) conditions. The visual performances of nine subjects were quantified by measuring the subjects? speed and accuracy in detecting floor objects located on axis and at ±20 degrees off axis. The objects were located near field (1.83 meters) and far field (3.66 meters). Upon presentation of the objects, subjects would count and point to each object using a red-laser pointer. The object detection response time and number of missed objects were recorded. The results of the visual performance comparison for an LED, a prototype LED, and an incandescent cap lamp are presented. There we no missed objects when subjects used the LED-based cap lamps but, there were three missed object occurrences when subjects used the incandescent cap lamp. The mean detection time when using the incandescent cap lamp was 55.3% greater than the prototype LED cap lamp and 43.5% greater than the LED cap lamp. It can be inferred from this data that the spectral distribution of LED-based cap lamps could enable significant visual performance improvements as compared to incandescent cap lamps1.

Jan 1, 2007

By W. J. Vlasblom, A. M. Talmon, A. J. Nobel

In initial laboratory tests with a travelling submerged jet on artificially prepared clay it was found that the cavity depth is dependent on the stagnation pressure of the jet and the undrained shear strength of the clay. In addition, it has been observed that the increase in cavity depth with jet pressure is stronger at higher jet pressures. It is assumed that this can be explained by cavitation of the jet at higher jet pressures. At cavitation a cone of bubbles is formed around the jet, which reduces the exchange of momentum between the jet and the surrounding water. This results in a higher jet velocity and a higher stagnation pressure at a specified distance from the nozzle exit. In literature, no relation between the jet pressure of a free submerged cavitating jet and stagnation pressures was found. Additional tests were carried out to determine this relationship. Because practical dredging occurs at relatively large water depths, these tests were performed in a pressure vessel at different pressure levels. It is concluded that the efficiency of a jet (defined as the stagnation pressure at a certain distance divided by the jet pressure), for stand-off-distances smaller than 45 times the nozzle diameter, increases significantly by cavitation in comparison to the non-cavitating situation. However, the jet pressure required for a fully developed cavitation cone increases strongly with water depth. At dredging depths of 20 m and more, the necessary jet pressures are higher than normally applied in dredging practice. Thus in spite of the importance of cavitation in laboratory tests at atmospheric pressure, in normal dredging practice cavitation is of less importance.

Jan 1, 2007

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007

Project evaluation is completed through individual studies covering technical and financial aspects of the mine to market. These studies are completed at various levels of detail depending on where the project evaluation is in the project's life cycle. The competency of the studies varies in relation to the quality of data, level of the skills employed, control, management and reporting structure. The focus of this paper is managing elements of the study, looking at the cost of opportunity to influence the project, against the value added. Selection of the study manager and study teams is central to getting an integrated project evaluation addressing the correct issues completed on time. Retention of key personnel can reduce rework which, in turn, can reduce time and cost impacts. It is important to have a work breakdown structure at the outset so that the study teams have a common numbering and naming system that will integrate areas, equipment, budgets estimates and accounts. Having set up the evaluation groups and provided training in the study procedures, understanding the scope and schedule are vital elements in producing a project evaluation that addresses the opportunities and the risks of the final project. Arriving at an accurate capital budget requires integration of the research controlled through common systems. Project evaluation process must also address how the project is to be delivered.

Jan 1, 2007

This paper summarises some observations regarding the way SAG and AG mills work based on the last ten years of pilot plant operation, grinding circuit design and operational reviews for various projects in Australia and overseas. The main purpose is to promote discussion on key factors influencing breakage in a SAG mill. The focus of the paper is on two questions: How do mill lifters and liners really work and have an effect on grinding? How does the mill charge composition impact on grinding performance? The focus of the paper is on observations of mill behaviour in both pilot plant trials and plant operation, particularly on Cadia ore. DEM, by others, and JKSimMet modelling of SAG mill performance have greatly assisted in forming the ideas expressed in the paper and both are valuable tools in developing our understanding of the comminution process. Put in the æextremeÆ form the major observations and conclusions expressed in this paper are that: the main purpose of mill lifters is to reduce mill liner wear and not to promote rock breakage; the often promoted theory that balls impacting the ætoe of the chargeÆ is a dominant form of breakage is incorrect; and fines production in a SAG mill is primarily a function of the rock load mass, with a secondary dependence on ball load for any given circuit configuration.

Jan 1, 2007

By J. Hollow, D. Walsh

The Fort Knox Mine is located in Alaska’s interior, where the average ambient air temperatures range from -24oC in January to 16oC in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and a conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leach, carbon adsorption and cyanide destruction kinetics. Additionally, an energy balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post project plant performance that validates the model and shows the mine produced an additional 596 kg (19,155 ounces) of gold, while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007

By M. Schwarze

SMS Meer GmbH with its COPPER PLANTS DIVISION produces a full line of systems and machines for the processing of copper. The product range includes: shaft melting furnaces, anode casting lines, horizontal and vertical casting lines, casting and rolling lines for copper wire rod and strip, cold pilger mills, planetary rolling mills as well as tube drawing equipment. The new designed shaft furnaces are the most economic way of copper melting. The CONTILANOD® system with hydraulic shear represents a breakthrough into higher production capacities and improved geometrical accuracy of anodes. The new generation of CONTIROD® lines with individual drives of rolling stands guarantee cost effective production of highest rod quality. A new horizontal continuous casting technology for the production of tube shells as feed stock for the copper tube manufacturing process ? directube® was developed and introduced into production. A first line for continuous vertical strip casting - called VERTICAST® - for higher production rates and improval quality of cold-rollable strips is in the final stage of commissioning. These innovative technologies increase product quality, reduce process costs and help for a wide use of copper in all sectors of life.

Jan 1, 2007

By Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory are developing a borehole profilometer to dynamically measure the roughness pro-file of boreholes used to install roof bolts fully encapsulated with resin. Numerical measures of roughness were calculated from profiles of borehole surface roughness to determine potential roof bolt anchorage capacity. The concept of dynamically profiling was proven through the following series of laboratory tests: a sensitiv-ity test using various grits of sandpaper, a known-profile test along a section of a concrete hole, and a simulated borehole test in a pipe with machined grooves. Two profilometer prototypes were devel-oped that measure slight changes in the radius of a borehole using either strain-gauged, spring-steel arms or rigid, steel arms attached to a spring-loaded cone and a linear potentiometer. Both instruments performed reasonably well in the laboratory and were subsequently tested in boreholes drilled in two concrete blocks using different drilling techniques to obtain three different borehole surface roughnesses. A Z2 roughness parameter was calculated with data from the first profilometer, and an average radial increment was calculated from the test results of the second profilometer. Although both instruments were able to readily distinguish the difference between smooth and rough boreholes, the correlation coefficient (r2) for a linear relationship between Z2 and average radial increment was 0.577. Pull tests were conducted with resin bolts installed in the concrete blocks, but maximum pull-out strength could not be correlated to borehole roughness because in each of these tests, failure occurred at the resin-bolt interface. A more sophisticated prototype has been designed to measure surface roughness and also accurately determine the location and tilt of the instrument in the borehole. However, this instrument has not yet been fabricated or tested.

Jan 1, 2007

By M. Sagedahl

The off gas from a smelter is cooled and dust removed in an electrostatic precipitator before approximately 95% of the sulphur dioxide (S02) is converted to sulfuric acid. However, the tail gas may need to be polished to remove the rest S02 to meet demands. A flue gas desulphurization (FGD) system, as usually applied to S02 removal on coal and oil fired Power Station, is suitable for polishing tail gases from copper smelters. The ALSTOM Seawater FGD process makes use of the alkalinity in the seawater to absorb and neutralize S02. Before being returned to the sea, the seawater is treated to comply with environmental regulations. As the ALSTOM Seawater FGD process uses no reagent and produces no byproduct, it is extremely cost-effective for coastal installations. The first SWFGD plant started operation in 1968. Over 60 of these units have been installed worldwide. The ALSTOM Seawater FGD process removes S02 from flue gas flows corresponding to a total of 70,000,000 Nm3 /h. Suitable for thermal power stations, smelters and oil refineries, ALSTOM Seawater FGD plants efficiently treats flue gases in the range of 300,000 Nm3/h to 2, 700,000 Nm3 /h per FGD plant, containing 20 - 6,500 ppm of S02.

Jan 1, 2007