Search Documents

By D. F. Sinclair

It is often said in business that if you don't have a customer you don't have a business. The same rule applies to project evaluation; if you don't have customers you really don't have a viable project. It is therefore essential that in the early stages of project evaluation the following fundamental questions are addressed: ? What products will this project produce? ? Who are the potential customers? ? What are the customers' requirements with respect to grade and impurities? ? Do they have adequate capacity to take the production from the proposed project? ? Will the products introduce adverse effects in the customer's process circuits? ? Will additional waste streams requiring disposal be produced? In the past the attitude has been along the lines of the customer will take whatever we produce at the mine site. Times have now changed with customers now operating under much tighter environmental regulation with waste disposal becoming increasingly difficult. It would therefore be prudent that the principles of product stewardship be used as a tool in project evaluation. This paper will provide a general discussion on customer requirements and provide detail on case studies of the impact of mine products on smelter process circuits. It will provide examples where there were synergies between the mine product and the smelter circuit and where the mine product had adverse impacts on smelter performance.

Jan 1, 2007

By N. M. Can

The effects of microwave treatment on the floatabilities and magnetic susceptibilities of some sulfide minerals, namely, pyrite, chalcopyrite, galena and sphalerite, were studied. Pure mineral samples were prepared in -425+212-µm, -212+106-µm and -106+38-µm size fractions. Microflotation and magnetic separation tests were carried out on the samples after microwave treatment at 600, 950 and 1,300 Watts for 5, 20, 60, 90, 120 and 240 seconds. The maximum temperature values of the samples were measured during the microwave treatment, and possible altera-tions on the mineral surfaces were determined by X-ray diffraction (XRD) analysis. The effects of microwave treatment are discussed based on the result of microflotation and magnetic separation tests. The results revealed that pyrite, chalcopyrite and galena were heated very quickly and that their surface temperatures reached ~700° to 900°C, while the temperature of sphalerite reached only ~130°C. The floatability of pyrite, chalcopyrite and galena were decreased when microwave energy and the duration of treatment were increased, owing to oxidation of the mineral surfaces caused by relatively high temperature. As expected, there was no change in the floatability of sphalerite. The magnetic properties of pyrite and chalcopyrite were improved by the increase in microwave energy and the duration of treatment to such an extent that 90% of the feed separated as magnetic product. But no change was observed in the magnetic properties of galena and sphalerite.

Jan 1, 2007

By V P. Beskrovnaya

Tests for the development of a metals recovery technology from samples of a Russian gold-bismuth deposit were carried out. Gold, silver and bismuth assay reported 5.6 g/t, 3.0 g/t and 0.08 per cent, respectively. Two flow sheet options were pilot plant tested: gravity/cyanidation of gravity tailings with subsequent flotation of cyanidation/carbon-in-pulp (CIP) tailings, and gravity/flotation concentration with cyanidation/CIP of concentrates. Option 1 results showed lower gold, silver and bismuth recoveries (81.3 per cent Au, 55 per cent Ag and 74.0 per cent Bi) due to low flotation efficiency for cyanidation tailings. Therefore, a flow sheet involving gravity/flotation concentration to produce bismuth-gold concentrates (0.8 per cent Bi) with subsequent cyanidation/CIP was recommended. Gold, silver and bismuth recoveries obtained by this method to the combined gravity/flotation concentrate were 90.2 per cent Au, 83.3 per cent Ag and 80.2 per cent Bi of the ore, respectively. Overall gold, silver and bismuth recoveries were 83.0 per cent Au, 40.5 per cent Ag and 80.2 per cent Bi, respectively. Gold and silver recoveries to the cathode precipitate were 92 per cent Au and 48.6 per cent Ag (per operation). Reagents consumed for flotation were 0.1 kg lead acetate/t ore, 0.4 kg butyl xanthate/t ore, 0.2 kg T-80 frother/t ore, 0.02 kg sodium hexametaphosphate/t ore, 0.15 kg copper sulfate/t ore. Reagents consumption for cyanidation was 0.42 - 0.48 kg NaCN/t ore and 0.2 kg CaO/t ore. It was recommended to deliver bismuth concentrates after hydrometallurgical treatment to a smelter. Overall bismuth recovery including bismuth recovery achieved by pyrometallurgy was 60.0 per cent. However, it was obvious that delivery of bismuth concentrates to a smelter and their commercial treatment would be very expensive due to relatively high mass pull of bismuth concentrates (7.6 per cent of the ore weight). For this reason, thiourea leaching and hydrochloric acid leaching with subsequent cyanidation/CIP were investigated as alternatives to cyanide leaching. These two alternatives were proposed to enable optimal recovery of valuable metals from concentrates on-site. Recoveries obtained by thiourea leaching were 91.2 per cent Au, 90.5 - 91.9 per cent Bi and 77.0 - 78.1 per cent Ag. However, that method required considerable capital and operating costs. As an alternative, hydrochloric acid leaching with subsequent cyanidation was investigated. Test results showed improved gold, bismuth and silver recoveries, which were 94 - 95.9 Au per cent, 94 - 96 Bi per cent and 76 - 78 Ag per cent, respectively. Hydrochloric acid consumption was 100 kg/t concentrate or 7.6 kg/t ore. Current efficiency during electrowinning was about eight to 12 per cent. A recommended flow sheet involving hydrochloric acid leaching of concentrates, electrowinning of bismuth from solutions, recycling solutions after electrowinning and cyanidation of hydrochloric acid leaching cakes is described. Overall recoveries achieved by the proposed flow sheet were as follows: 84.8 - 86.5 Au per cent, 75.8 - 76.9 Bi per cent and 63.2 - 64.9 Ag per cent. Based on results from these tests, initial data for a bankable feasibility study and plant designing were developed.

Jan 1, 2007

By T. Nishi, D. Teguri, K. Saitoh

In recent years the requirement for high carbon ferro-manganese (HCFeMn), which is the key product of our company, has increased due to bullish demand for steel products. In our Tokushima works, we have 2 closed types of electric furnaces (1F and 2F), with which we are manufacturing HCFeMn. In order to meet the increase in demand, we made various modifications to these furnaces and we tried to increase the furnace operating loads. Especially for 1F, we deepened the furnace. In this paper, we report the results of this modification. The operational situations of the above-mentioned two furnaces are different because they have different individual profiles. As for 1F prior to modification, the depth of the furnace was one meter shallower than2F, because 1F was designed for the manufacturing of SiMn. On the other hand, our Tokushima works specialized in HCFeMn 14 years ago. However, the profile of 1F was not optimized for HCFeMn. In comparison to 2F, 1F was more difficult to stabilize due to the smaller tolerance for the adjustment of the electrode length, the metal / slag level, and the coke-mixing ratio. We deepened 1F by 770mm by disposing of the furnace rolling mechanism. We consequently achieved a 10% increase in production capacity. This meant the operating load was enhanced from 24.5MW to 27MW, the furnace became more stable and the tapping speed of both metal and slag increased, all which made the tapping easier than before.

Jan 1, 2007

By K. Pienimäki

Boliden Harjavalta Oy has produced copper since 1945. The essential idea has always been continuous development of process efficiency and environmental friendliness by using the Best Available Techniques (BAT). The ongoing development step is to increase the production capacity up to 210 000 tpy of anode copper and 155 000 tpy of copper cathode. One of the focal issues in this action is modernization of the copper refinery to utilize permanent cathode technology. This paper describes the refinery project and the technology used in it.

Jan 1, 2007

By M. Hamamoto, M. Furuta, S. Tanaka

The Tamano smelter and refinery has expanded its production from 228kt/y to 260kt/y since 2006. It was not a big jump, but efficient and economical improvements were executed. These were not only de-bottlenecking and modernization of the smelting plant, including the acid plant, but also additional processes were commissioned, e.g. slag cleaning furnace and steam dryer. On the other hand, a conversion to permanent cathode process in the #2 tank house made the biggest impact on production efficiency for the refinery plant. In order to overcome the drastic change of copper business, although each scale is not so big, continuous improvements are very important to survive. This paper mainly describes the recent improvements of the smelting plant.

Jan 1, 2007

By L. Haavanlammi

The Outokumpu HydroCopper® process is a chloride based atmospheric leaching process alternative that can treat a variety of different concentrates. Chalcopyrite and other copper sulfides can effectively be leached under atmospheric pressure in strong, aggressive chloride solution using copper (II) ions as oxidant. Impurities are removed from the solution as carbonates and ion exchange. Copper is precipitated from the purified pregnant leach solution as copper (I) oxide, which is filtered and reduced by hydrogen gas to metallic copper powder, which is melted and cast into copper product. Sodium chloride solution from copper (I) oxide precipitation is decomposed in a chloralkali electrolyser, to products of which are circulated back to the process. The process has been designed for copper concentrates and is a fast and economical way to produce copper wire rod directly from concentrate. The process can efficiently handle impurities like arsenic and mercury, which can be harmful in the pyrometallurgical processes. The process has been tested in the laboratory and 1 ton/day demonstration plant scale and it has been proven to be commercially viable. The process has been designed to meet the strictest directives for emissions. Other environmental factors are carefully considered to obtain the highest possible eco-efficiency.

Jan 1, 2007

By C. Carrasco

Caletones Smelter, Division El Teniente of Codelco Chile, has used Teniente Converter (TC) as the only smelting unit since November 2000. The modernization project considered the shutdown of the last reverberatory furnace, the installation of the fourth Teniente Slag Cleaning Furnace, the installation of a new fluidized bed dryer and the modification of the concentrate injection system into TC. The modernization project and related investments allowed for the increase of the smelting capacity up to 1.25 million t of concentrate annually.Next stage of the smelter expansion in the year 2004 considered the increase of the smelting capacity up to 1.44 million t/year. The expansion required technology modernization and the installation of the new equipment, such as concentrate injection system, oxygen plant, fluidized bed dryer and storage bin. Currently the annual smelting capacity is about 1.35 million t of copper concentrate, being limited by sulphuric acid plant treatment capacity. This paper presents the technology and production evolution in the Caletones Smelter in the years 2000 - 2006, demonstrating the potential of development and competitiveness of Teniente Converter as world-wide recognized smelting/converting reactor.

Jan 1, 2007

By G J. Butler

Since 2005 BHP Billiton Iron Ore has been working with the consulting company Runge to implement the software XPAC Advanced Destination Scheduler (ADS) in life-of-mine studies. The Mt Whaleback mine, being the single biggest open cut iron ore mine in the world, presents some special challenges in scheduling. The biggest challenge has been the slow run time and difficulty in targeting all ore and waste requirements. The high waste to ore strip ratio means that much of the cost of mining is tied up in waste dumping. It is therefore very important to schedule waste efficiently. At Mt Whaleback there is an additional challenge of managing two types of waste: inert and environmentally sensitive pyritic material. This paper shows how the XPAC destination scheduler is configured to achieve efficient and repeatable waste scheduling results at the Mt Whaleback mine. It also discusses proposed improvements to the process. The overall ore and waste schedule is configured to target mining parameters, crusher feed and grades. The schedule is run in two stages. The first stage is ore mining. The waste that needs to be mined is locked in a sequence. The second stage is the waste scheduling. The waste destination scheduler uses three inputs: source waste parcels locked in a sequence, a haul road and a waste dump block model. The process involves setting some rules for dump progression and haul path selection. These can be validated. The schedule is then run to target the shortest travel time. The results of scheduling are graphical and numeric and can be transferred into many different formats for reporting. The graphical result shows face positions in time that can be used for detailed dump design. The numeric results are used to estimate truck fleet size, fuel consumption, labour and equipment financials. The process has been successful in reducing the project time line, increasing the ability to do more scenarios and increasing schedule accuracy, transferability and repeatability.

Jan 1, 2007

By E. J. McLean

Gold mineralisation at Bendigo is exclusively associated with quartz reefs, commonly found within or near anticlinal fold hinges. The gold is typically coarse grained (0.5 mm to 5 mm), free milling and displays a complex, nuggetty distribution within the veins. This ore is highly amenable to gravity recovery processes. As the Bendigo operation is not permitted to treat whole ore by a cyanide leach/CIL circuit, the flow sheet is more complex than conventional gold recovery circuits. Primary gold recovery is from a gravity circuit closing the grinding circuit to a bulk gravity concentrate and from a flotation circuit treating cyclone overflow to a bulk float concentrate. The plant capacity is relatively low by current gold industry standards at 600 000 tpa. Re-establishing gold production at Bendigo has presented several challenging, and sometimes competing, issues in process design and operation. The mine, process plant, associated services and infrastructure are at Kangaroo Flat, a low density, semi-rural zone in the southern urbanisation of the Bendigo metropolitan area. One of the main processing challenges during the design was the competing comminution requirement to avoid over-grinding, which would flatten or smear the characteristic nugget gold and hinder effective gravity gold recovery, whilst also providing sufficiently well liberated particles that would respond well to flotation. Important, non-metallurgical challenges were to minimise impacts on the local community from noise, dust, air emissions, visual impact, water egress and off-site traffic.

Jan 1, 2007

By S. Kawai

Natural convective flow of the electrolyte solution plays an important role in several electrochemical systems. Copper refining electrolysis is the most important industrial process to produce high purity copper on large scale. Turbulent natural convection develops along vertical plane copper electrodes installed in an unstirred electrolyte accompanying with the electrochemical deposition and dissolution of copper during the electrolysis. It introduces the electrolyte stratification phenomenon. Thus, the electrolyte is circulated in a special way depending on each electrorefining tankhouse. The theoretical discussion is indispensable to understand the coupling phenomenon between the ionic mass transfer rate and the morphological variations of electrodeposited copper. In present study, the mass transfer rate of both Cu2+ and H+ ions as well as the momentum transfer rate is numerically analyzed accompanying with the turbulent natural convection along 1 m high Cu metal electrode surface.

Jan 1, 2007

Pisolitic iron ores (also known as channel iron deposits) are an important resource of medium-grade iron ore in the Hamersley Province of Western Australia. They are a special case of transported pisolitic ferricrust, differing from normal transported ferricrust only in the exceptionally high iron and low alumina content. The pisoids typically range up to 5 mm in diameter with abundant particles of ferruginised fossil wood up to 15 mm in maximum diameter preserved in the sediment. Field observations indicate that pisoliths are commonly initiated by the action of raindrops on iron-rich soil. Pisolites form by the impact of raindrops forming coated beads of ferruginous soil, which after dehydration obtain additional coatings during successive showers. Thick deposits of pisolite that are transported and deposited primarily by sheetwash form in the distal regions of the pediment. A size range limited to particles that may be transported by extremely shallow water characterises the abundant fossil wood fragments. The absence of fine sedimentary layering in pisolitic iron ores is explained by the action of soil-forming processes after deposition, while the major coarse bedding features derive from successive erosional and depositional events in the evolution of the pediment. They are not deposited in channels by rivers which, in arid to semi-arid conditions, typically deposit quartz sands and gravels with characteristic point bars and current bedding, abundant ferruginous granules, but rarely pisoids. However, they may fill abandoned river channels.

Jan 1, 2007

By J. Drzymala

Particle beneficiation tests are often conducted to determine how the recovery of a key component of a particle mixture varies with overall product yield, i.e., the separation curve. The results can be misleading when an attempt is made to determine the effect of feed grade by comparing separation curves representing different feed grades or key component concentrations. This is a shortcoming of the conventional recovery versus yield diagram, which may not appear to be affected by feed concentration. To overcome this shortcoming, a method is presented for transforming and normalizing the recovery and yield coordinates so that the separation curves representing dif-ferent feed concentrations are directly comparable.

Jan 1, 2007

By Yifan Ding, Shemek Oginski, Patrick Finn

The Manhattan section of the New York Water Tunnel No. 3 constructed by the Schiavone/Shea/Frontier-Kemper Joint Venture is a $668 million project. The contract includes a tunnel drive of 8.85 km (29,045 feet), tunnel lining of 14.77 km (48,468 feet)and construction of nine shafts ranging in depth from 143 m (469 feet) to 169 m(555 feet). Construction methods for excavation of the shafts are presented including raise bore, ground freezing, soil excavation, blasting, slashing, muck handling, rock support and shaft final concrete lining.

Jan 1, 2007

By R Lurf, C Weber

In the frame of this paper a holistic dynamic process model approach is presented in order to introduce operational and technical excellence in drilling and blasting. Both on a macro and micro level the single process parts of drilling and blasting are outlined and their interaction is explained. The use of this approach for closing the gap between process planning and process implementation is explained and an example of the value generated is given.

Jan 1, 2007

By S. Marsland

Reference materials have always been important for validating and controlling analytical methods. They have recently become even more important as quality requirements have become more stringent and customer demands for properly verified and controlled results increase. Clients, especially from the resource exploration industry, demand critical validation of all results reported. Mintek has been producing geological and semi-processed ore references since the early 1970s and recently, due to increase in demand, other manufactures have entered the South African market. This paper describes analytical challenges from the customers? perspective, the customers being metallurgists, mine geologists, environmental scientists and geologists from resource companies. Reference materials with their appropriate use and a good understanding, can aid greatly in building confidence in the results, choosing the right laboratory for a project, deciding which set of results is correct and providing evidence to the customers? clients that the best possible results have been obtained

Jan 1, 2007

By T. Lu

Microwaves have considerable potential as an energy source in both mineral processing and metals extraction. In this research, the utilization of microwave radiation for the heating of a gibbsite type bauxite ore was investigated. Firstly, thermogravimetric studies were performed in order to characterize the dewatering processes of the ore. Secondly, both the real and the imaginary permittivities, which are the fundamental properties that determine the interaction of microwaves with any given material, were measured for the bauxite ore as a function of temperature. The changes in the permittivities were shown to be related to the dewatering processes. Subsequently, the effects of operating variables such as processing time, sample mass, particle size, microwave power, sample bulk density and carbon and magnetite additions on the sample temperature in a microwave field were studied. The results showed that under suitable conditions the bauxite ore could be readily heated. Therefore, there is considerable potential for the application of microwaves for the heating of bauxite ores.

Jan 1, 2007

By Walter I. Paniagua

Drilled shafts and precast concrete piles were installed for the foundation of several structures in a reconfiguration project of a refinery in Minatitlan, Veracruz, in the Gulf of Mexico. The soils are alluvial deposits of flat land from the Coatzacoalcos River, which are embedded with layers of sand, soft clay, and peat. As part of a QC/QA program, load tests, both static and dynamic, axial and lateral, were performed. In this paper results of 32 axial tests are presented, in which typical load-displacement curves were measured at the top of the foundation elements; from the interpretation of these plots, data were recorded for ultimate side shear and in some cases for end bearing capacities, which are compared with the theoretical results of the final stage of the foundation design. The comparison shows that under allowable loads, side shear determines the bearing capacity of piles, even when the tip is embedded in a hard layer. Underestimation of the side shear is evident; therefore design criteria, as well as the methods used for obtaining soil parameters, should be reviewed.

Jan 1, 2007

Cautionary Note about Forward-Looking Statements Certain statements made by us in this presentation that are not historical facts or that relate to our future plans, expectations, events or performance are forward-looking statements within the meaning of the federal securities laws. Our actual results may differ materially from those expressed in any forward-looking statements made by us. Forward-looking statements involve a number of risks and uncertainties including, but not limited to, the risks described under the heading ?Risk Factors? in the Prospectus Supplement. All forward-looking statements are qualified by these risks and uncertainties. We undertake no obligation to update the information contained in any forward-looking statements unless required by law. All statements made by us in this presentation are further qualified in all respects by the information disclosed in the Prospectus.

Jan 1, 2007

By Craig M. Sams

"Variable speed mill popularity has grown during the last 10 years with almost every SAG mill fitted with a variable speed drive. In addition, many of today’s larger ball mills are running a variable speed drive for various reasons. In the past, motor suppliers, especially gearless drive suppliers, have considered mills as being an overpriced rotor. This has lead to mills demanding more torque than what a motor can generate. This paper identifies the reasoning of what has happened and how to mitigate the mismatch in the future. Technical and economical issues are discussed, allowing mill operators to make an informed decision of which path to take in deciding what motor to put on a mill.INTRODUCTIONIt has been generally accepted in the past that motor suppliers and specialists in engineering companies understand the workings of a SAG mill or a ball mill and although there is a fair knowledge within the industry, in regards to mill torque requirements, the advent of variable speed drives in ball mills has shown the writer that a complete understanding of the mill torque requirements are not fully understood.This paper will discuss two aspects of mill torque requirements, (operating torque at various charge levels and start up torque), and how it relates to specifying the proper motor torque requirements.MILL OPERATING TORQUEMill operating torque at a given charge level and density in a mill is essentially constant throughout the entire speed range. For the purpose of this paper, we will take a 38’x 22.5’, 20’ EGL, SAG mill and provide the power draw at variable speeds but fixed loading conditions.The power draw and mill torque of this mill at 8% ball charge and 28% total loading (Highlighted) is shown below as Figure 1, at variable speeds."

Jan 1, 2007