Search Documents

By Marcelo R. Esquivel

A MmNi5 alloy is synthesized by a combination of mechanical milling and low temperature heating processes. Synthesis time is 40 h for powders milled in a low energy ball mill at room temperature. A reduction in milling time is obtained if massive sample is mechanically milled at shorter times (2 h to 10 h) and heated at temperatures lower (600 ºC) than the usual temperatures used in equilibrium methods (>800 ºC). The alloy formation is detected even at a combination of temperatures as low as 200 ºC and milling times as short as 5 h. The temporal evolution of mechanical milling process was followed by both X-ray diffraction (XRD) and scanning electron microscopy (SEM) to detect the main stages of milling. Four stages were detected: Initial, Intermediate, Final and Completion. These stages were correlated to an enhancement of the synthesis method by combination of times of milling shorter than 10 h and temperatures of heating lower than 600 ºC.

Jan 1, 2006

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By Eiji Kojima

In this research, dynamic and static load tests were performed on permanent foundation piles which had a pile length of 30 m, 800 mm in outer diameter and 15 mm in wall thickness. In this site the dynamic horizontal load test on a smaller test pile, 12 m in length, 500 mm in outer diameter and 12 mm in wall thickness, was also carried out. The static horizontal load versus horizontal displacement derived from the dynamic load test conformed well to that measured in the conventional static horizontal load test of the pile with 800 mm diameter. Then an attempt was made to predict the horizontal load displacement of the pile with 800 mm diameter based on the results of the dynamic horizontal load test of the pile with smaller diameter of 500 mm.

Jan 1, 2006

By M. J. Little

Potgietersrust Platinums Ltd is Anglo Platinum?s only open pit operation and annually extracts 57 million tonnes of rock from 2 open pits. Over the past 3 years ~220 km of exploration drilling has been done, ~1000 km of rock face have been exposed for face mapping and over 7000 laboratory and field tests have been conducted. This has produced large amounts of geotechnical data to be utilised for feasibility studies, initial slope design and ongoing slope optimisation. It was necessary therefore to develop geotechnical databases to manage the vast amounts of data collected. SABLE and MineMapper 3D databases were created for logging and mapping respectively, with rock testing data incorporated into both. A pit inspections database was developed in MS Access and the existing groundwater and slope monitoring database was improved. The databases were linked to AutoCAD and Datamine to ensure that the latest geotechnical data is used for planning, draughting and modelling. The use of geotechnical databases ensures that no data is lost, standards are maintained and analysis can be easily performed. This increases the confidence of the analysis and allows the geotechnical engineers to optimise slope designs and blast designs on a regular basis. This reduces the risk of slope failure thus making the open pits more economical and safe.

Jan 1, 2006

By Chunlin Chen

Published data on thermodynamics of a number of minor elements (As, Sb, Bi, Pb, Zn, Se, Te, Cr, Sn) in liquid copper, matte and slag have been reviewed, assessed and used in development of thermodynamic solution models of melts. The behavior of antimony in alloys, mattes and slags is used as an example to illustrate the approach taken in assessment of published data and validation of the developed models with respect to the activity of Sb in condensed phases as well as the effects of matte grade, slag chemistry, temperature etc on the equilibrium distribution of Sb between melts and the gas phase. Results obtained from a comparison of different smelting processes with the modeled multi-phase equilibrium are presented and discussed. The predicted effects of slag chemistry and matte grade on the deportment of other minor elements during smelting of copper mattes will be presented and discussed.

Jan 1, 2006

By Florian Kongoli

The so-called "fayalite" slag, despite problems associated with it, is the most widely used slag in copper smelting processes. Thirty years ago, in order to overcomes some drawbacks of this slag a new "calcium ferrite" slag was proposed especially for continuous copper converting. Since both slags have strong and weak points depending on the field of their application about 8 years ago another new "ferrous calcium silicate" slag was proposed that is expected to solve the drawbacks of each slag. This new slag is defined as mainly consisting of FeOx, CaO and SiO2 as its main components but it can practically have several combinations of these constituents. In order to determine the best area of this slag for possible industrial application the quantification of phase relations is an important subject. In this paper the work carried out by the authors in quantifying through an original physical model the phase relations, liquidus surface, liquidus regions, behavior of solid phases and the effect of minor components is reviewed. Several special compositions of this slag have been identified and discussed for possible applications in the industrial practice.

Jan 1, 2006

By M. A. Qianjie

The problems of coalmine safety in china remain unsolved for decades. Starting with the description on safety status quo of coalmine in china, different existing analysis and measures discussed for the safety problem solution of coalmine china. With the consideration of system thought in mind, the author present with a unique systematic reason analysis method on such actuality--individual analysis and general analysis--each for its particular purpose. Upon such cause analysis, construction of the safety system is made clear and, solutions for such problems provided.

Jan 1, 2006

By H. Verakis, M. J. Sapko

The Pittsburgh Research Laboratory (PRL)1 of the National Institute for Occupational Safety and Health (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) Technical Support Center has devised a prototype hand-held instrument which can provide a direct assessment of the potential explosibility of a coal and rock dust mixture. Current Federal regulations require that rock dust be applied in all underground areas of a coal mine to mitigate the propagation of a coal dust explosion. To determine compliance with the Federal regulation, mine inspectors collect dust samples from sections of underground coal mines for an MSHA laboratory analysis of incombustible content. However, the laboratory analysis may not be completed for more than a week or two, during which time the mine area from which samples are taken may be inadequately protected. The operation of the Coal Dust Explosibility Meter (CDEM) is based on the difference in optical reflectance between light rock dust and dark coal dust. For a given coal volatility, the optical reflectance of such mixtures is relatively constant at the limit of explosibility, independent of the coal dust particle size. The CDEM is not intended to replace the current MSHA laboratory analysis of coal mine dust samples for incombustible content, but to serve as a supplemental device for enhancing mine safety through improved rock dusting practices.

Jan 1, 2006

By Wenshan Zhang

Three important methods of removing Fe in hydrometallurgy of zinc, manganese, copper, nickel, cobalt and etc are described, including neutralized hydrolysis method, jarosite method and goethite method. The reactions, technical requirements and thermodynamic analysis during Fe removal process are also discussed in this paper.

Jan 1, 2006

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

By P. S. Baker

CRU estimates that the global supply of metallurgical grade alumina (MGA) grew by 5 percent during 2005 to a little more than 61 Mt (67 million st). About 30.7 Mt (33.8 million st), or 50.3 percent, of that originated from Oceania (principally due to the commissioning of the CAR refinery in Australia) and Latin America. In this context, Chinese production surged by 20.5 percent year-on-year to 7.7 Mt (8.5 million st) on the crest of a 17-percent rise in that country’s primary aluminium production. Meanwhile, on the demand side, there was a 6.7 percent climb year-on-year in global consumption to 62.3 Mt (68.6 million st). This reflected a healthy demand for primary metal from aerospace, construction, packaging and passenger transportation (to a lesser degree) in the United States, China, Brazil, South Korea and India. So there was an overall supply deficit of more than 1.2 Mt (1.3 million st). This, combined with an 18.3-percent diminution in closing stocks (down to 35 days of requirement), lifted the average spot price of MGA by 17.6 percent year-on-year to US$448/t (US$406/st).

Jan 1, 2006

By M. Georgescu

In the framework of the rapid development of contemporary society, the use of underground space represents an emerging opportunity because it can contribute to decreasing pressure of occupation of ground space while in the same time it can increase the economic value of the useful mineral substances, also through underground establishment of dangerous surface activities, contributing thus in environmental protection. This paper underlines the most important benefits of underground space utilization with the objective the exploit the potential of this real resource.

Jan 1, 2006

By Hector M. Henao

The FeOX-CaO-SiO2 base slag at intermediate oxygen partial pressures is very often used in non-ferrous smelting processes. This slag would also contain Al2O3 and MgO because these compounds are normal components in the ore and the refractory of a furnace. The objective of the present work is to determine the effect of Al2O3 or MgO addition on the liquidus temperatures of the plain FeOX-CaO-SiO2 slags in the atmosphere between intermediate pO2 of 10-6 and that of iron saturation at 1250 and 1300 °C. The experiments were carried out at given mass%CaO/(mass%CaO+mass%SiO2) ratios ranging from 0 to 1 and at spinel-tridimite double saturation. The experimental results show that the effect of Al2O3 or MgO addition on the plain FeOX-SiO2-CaO slag is not uniform and depends on the content of Al2O3 or MgO, the oxygen partial pressure and the mass% CaO/mass% SiO2 ratio. It is apparent that Al2O3 or MgO addition enlarges the spinel or wustite saturation area at almost all the oxygen partial pressures and temperatures of this research. The obtained phase diagrams will be useful in the metallurgical industry to assist in the selection of slag chemistry, operation condition and development of new processes.

Jan 1, 2006

By C. R. Landis

The Wyoming bentonite industry finished 2005 with strong growth. For most of the markets, demand exceeded supply. The industry continues to be heartened by the strength of its longtime markets, oilfield and iron ore pelletizing markets. But overall, all of the major markets enjoyed good to excellent commercial conditions. Growth at the macroscale was fueled by the continued strong domestic economy, by the exchange rate of the U.S. dollar in global markets and by strong worldwide global demand. As result, two new greenfield operations are in the early stage of development in the Wyoming region for the first time in more than two decades.

Jan 1, 2006

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006

By Partha Patra

Extracellular bacterial protein (EBP) from Paenibacillus polymyxa was isolated. Adsorption of bacterial cells of Paenibacillus polymyxa as well as EBP onto pyrite, galena and sphalerite was studied. Both bacterial cells and EBP was found to have different adsorption density for different minerals. Protein from mineral surfaces were extrated and examined through SDS PAGE electrophoresis. Specific group of protein was found to be adsorbing, specific to respective minerals. EBP was fractionated through FPLC. Adsorption studies were carried out with each fractions. Difference in adsorption density was observed for individual minerals. Flocculation and flotation experiment were carried out with these mineral specific EBP. Pyrite was selectively removed from ternary mixture of galena and spharite through flocculation anf flotation using pyrite specific EBP. Mineral specific EBP was found to selectively separated remove pyrite from the complex sulphide mixture.Zetapotential studies were carried out to examine the surface chemical changes of the minerals on interaction with EBP. Hydrophobicity of the minerals were carried out on interaction with bacterial cells as well as mineral specific EBP.

Jan 1, 2006

By Richard J. Hartman

Current design practice is to select steel sheet piling sections using sufficient section modulus and yield strength to resist the calculated bending moment. Thus, section modulus is the only property of the sheet pile cross section used in the selection process. Full scale laboratory testing documented that section modulus alone is insufficient to predict the strength of sheet piling. During testing, sheet pile sections with equivalent section modulus exhibited as much as 75 percent difference in load resisting capacity. Analytical study following the testing established that, in addition to the traditional longitudinal (vertical) stress in sheet piling, transverse (horizontal) stresses are also present. Transverse stresses reduce the ability of the sheet piling to function in the intended manner. It was found that transverse stresses result from the pressure applied by soil and water and that the capacity of the sheet piling diminishes with increased pressure. All sheet piling is subject to this behavior. This paper describes the testing and the results and establishes that a problem exists. A two dimensional procedure is described that assists in evaluating transverse stresses and their effect on sheet pile capacity. A method of creating design aids for use by engineers is illustrated.

Jan 1, 2006

By Bert Bahnson

As farms decrease and subdivisions increase there is a continuing demand for easy and safe silo removal. A few years ago I attended one of the Omni istribution explosive classes and was impressed by a product designed by Omni owner Bill Nixon called the Omni Breach. Its original purpose and main current use is law enforcement; specifically door breaching and tactical operations, with most of the force coming from water using a minimal amount of explosive component. I experimented with various charge strengths on concrete and found that it can be easily shattered with little flyrock or airblast. A neighbor of mine had an old silo within a foot of a barn that he was rebuilding and inquired about its removal. His property was sandwiched between an elementary school and Interstate 40, so I told him that I would do some test shots and if the results proved satisfactory, I would take the job for free to test the following theory.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006