Search Documents

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By M. Sahoo, P. Burke, Y. Fasoyinu, J. P. Thomson

The effects of grain refinement, mold temperature and chemical composition on the hot tearing resistance of aluminum alloys 535.0 and 206.0 has been studied by pouring constrained rod castings in metal molds. In addition, two prototype components that could be used in automotive applications were also poured from both alloys by gravity tilt-pour and low pressure permanent mold casting processes. This paper summarizes the results and issues encountered during the casting trials. It was shown that grain refinement and mold temperature ::::: 400°C reduced, and sometimes eliminated hot tear cracks in both alloys. The two prototype engineering components could be cast successfully from both alloys in metal molds. The metallurgical issues related to molten metal treatment and processing temperatures were well controlled. However, issues related to the control of hot tearing, casting and mold design must be addressed in future studies to guarantee the production of defect free castings.

Jan 1, 2006

By Yoshiaki Suzuki

In 1996, Saganoseki smelter & refinery successfully shifted to a single flash smelting furnace operation and increased the copper production capacity to 450,000mtpy in 1998. As the next step, Saganoseki planned to further increase the productivity in the smelting process. Applying the latest technology and carrying out technological innovations the throughput of the flash smelting furnace has been increased to 195 tons per hour and the matte grade has been raised to 68%. In 2005, six PS converters have been successfully consolidated into four by maintaining the production capacity. This paper introduces recent operation conditions and results of implementation of technological improvements.

Jan 1, 2006

By Robert Hopler

As a part of the depression and rectification work on the Port Morris branch of the Harlem Division of the New York Central & Hudson River Railroad, a short tunnel is being driven under St. Mary’s Park. The park is near 149th St. and St. Ann’s Ave., in the Borough of the Bronx, New York City.

Jan 1, 2006

By M. K. Elmouttie, G. V. Poropat

The analysis of structure using joint set statistics is well known. Other data such as the position of discontinuities and the contacts between rock mass units cannot be easily incorporated in simple statistical analysis based on orientation alone. Algorithms to model the structure of rock slopes using measurements of the orientation and position of discontinuities are being developed by CSIRO Exploration and Mining. These algorithms provide a capability to model the structure of a rock slope and estimate the likelihood of the formation of hazardous blocks in existing or proposed rock slopes and identification of the location and size of these blocks. The algorithms provide the basis of structural modelling to identify potential failure mechanisms in rock slopes.

Jan 1, 2006

XstrataÆs Mount Isa Copper Operations (MICO) is a world-class mining operation producing in excess of six million tonnes of copper ore per annum from its underground mining operations. The Mount Isa Copper Mines have been producing from the underground operations since 1952. Current copper reserves are 87 million tonnes at 2.8 per cent Cu, extending the mineÆs life beyond 2018. The underground orebodies in the copper mines are divided into nine distinct areas and are mined by sublevel open stoping techniques. One of the nine areas is the hanging wall lens, which consists of two sections; a northern lens (NHWL) and a southern lens (SHWL). The SHWL has a proven reserve of 2.2 million tonnes with an average grade of 2.9 per cent copper. Stopes in the SHWL have an average size of approximately 245 000 tonnes and will be extracted in a primary-secondary mining sequence, producing ore until 2009. This paper discusses various aspects of stope design applied in the southern hanging wall lens, including sequencing options and the rationale for the selected sequence. Design features are also discussed and how they have evolved as more is learnt about the SHWL orebody. These include mass firing techniques, focusing on minimising ground vibrations, using seed wave form analysis and prediction. Rock mechanics issues will also be discussed, in particular the reinforcement of stope hanging walls and the use of instrumentation to monitor behaviour within the hanging wall.

Jan 1, 2006

This symposium is dedicated to the lifetime achievements of Professor H.Y. Sohn. It covers the scientific fields, processing routes and investigation techniques in which Prof. Sohn has worked during his career and is based in the equally important three topical areas: Principles, Technologies, and Industrial practice. Professor Sohn was General Chair of the very first TMS Fall Extraction and Processing Symposium in 1983 in San Francisco which led to the Annual such symposia as this International symposium. Furthermore, the theme of that symposium was sulfide smelting, which is also included in this symposium. [ ] Professor Sohn was born in a beautiful dynastic capital Kaesung, Korea on August 21, 1941. He received his B.S. degree in 1962 from Seoul National University, M.Sc. in 1966 from the University of New Brunswick, Fredericton, N.B., Canada, and his Ph.D. degree in 1970 from the University of California at Berkeley all in Chemical Engineering. After working as a Research Associate at the State University of New York at Buffalo and as a Research Engineer at Du Pont?s Engineering Technology Laboratory, Dr. Sohn joined the Department of Metallurgical Engineering at the University of Utah in 1974 and currently holds the ranks of Professor of Metallurgical Engineering and Adjunct Professor of Chemical Engineering.

Jan 1, 2006

By F. Sekula

Tetrahedrite and siderite are two main valuable minerals present in the silver Mária Bana deposit. The tetrahedrite concentrate prepared from it by flotation has certain specific properties from the metallurgical point of view. Siderite is concentrated in the flotation tailings. The paper presents results of the laboratory and pilot-plant testing of the combined hydrometallurgical and pyrometallurgical methods proposed for treatment of the tetrahedrite concentrate and siderite waste. The testing conditions were based on thermodynamic analysis of the reactions that proceed in the process. The proposed technology makes it possible to separate copper from sulphur, mercury and iron in a straightforward way. Copper, after its refining, can be subsequently treated in the finishing operations. At the same time it is a valuable source of precious and noble metals. The siderite-containing flotation tailings can be converted to iron of the technical purity and slag. The proposed method is a good starting point for the development of the closed-cycle technology.

Jan 1, 2006

The resist profile simulation is carried out using the combined data obtained. The nematic liquid crystal is clear only when a long range order exists, in the whole medium. using the Jones matrix method. Director can change from point to point and is, in general, a function of space. Details of the lens structure and of the devices fabrication and performance are described. Light from conventional light source or laser is passed through a polarizer and then incident on the specimen At the nematicisotropic, transition temperature, the medium becomes isotropic and looks clear and transparent. The transition can be approached by changing the impurity concentration or, indirectly, by tuning the temperature since the pinning strengths of the random and crystal potential have in general a different temperature dependence.

Jan 1, 2006

By John R. Wolosick

MACROPILES are defined as ultra-high-capacity micropiles, with working loads in excess of 250 tons. The piles are typically 9-5/8 to 24 inch (244 to 610 mm) outside diameter. They are drilled and grouted in place, with either large diameter steel bars and/or steel pipe reinforcement. The piles are typically tested to twice the working load. Piles with working capacities of up to 500 tons and tested to 1000 tons have been installed. The paper discusses MACROPILE design philosophy, construction techniques, and two case histories where this innovative foundation system has been installed. Macropiles are descended from micropile technology pioneered in the early 1950s by Fernando Lizzi of Italy.

Jan 1, 2006

By Peng Bing

Stainless steelmaking dust is classified as a hazardous waste due to higher than acceptable heavy metal leachabilities such as zinc, lead, cadmium and chromium. In addition to being an environmental hazard, the flue dust is also an economical concern to stainless steelmakers as it contains large amounts of valuable alloying elements, especially for iron, chromium and nickel. A new technology of direct recycling of stainless steelmaking dust has been developed to recover the metals from the dust. But it was found that zinc was accumulated in the dust collection system in practical run of direct recycling. This study focuses on the effect of the operating parameters such as temperature, dust feed rate and the ratio of CO to dust on the reduction of zinc oxides present in the dust. The mathematical model for the reduction process was setup based on the experimental research. According to the mathematical model, the temperature has obvious effect on the reduction of zinc. It is benefit to the process of zinc reduction to increase the temperature. But the temperature will not be the main factor for the reduction process after 1228C. It will promote zinc reduction to decrease the dust feed rate and control the ratio of dust to CO. It was also found from the experiments that ZnFe2O4 in the dust could be decomposed at high temperature. Decomposing ZnFe2O4 in the dust increases the recovery of zinc from the dust distinctly.

Jan 1, 2006

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

By Patrick Pelletier Jr., Pierre-Alexandre Bossé, Gianni Bartolacci, Ian Orford, Steve Parent

"Over the last decades, many authors have shown the importance of froth in the flotation process. Mineral recovery is related to froth recovery and flotation. Selectivity is affected by froth characteristics, especially structure and loading. The characteristics of froth textures could therefore be used for diagnosing flotation.Machine imaging, especially image texture analysis, allows on-line measurement of important froth characteristics and process state classification. The measured characteristics include froth texture, loading and stability indicators. To extract information from images, texture analysis tools are used as well as a block-matching algorithm (BMA). For process state classification, images are analyzed with the same tools and clustering is done with multivariate data analysis algorithms.Two case studies, Brunswick Mine Concentrator Cu/Pb circuit and LaRonde Mine Zn circuit, are presented to show that these indicators may be used for diagnosis and control. The influence of manipulated variables on measured froth features is shown as well as the relationship between froth characteristics, mineral recovery and flotation selectivity.INTRODUCTIONImaging is a way to depict abstract characteristics of a scene or an object; it is often related to other types of scientific observations, chemical component concentrations, for example (Geladi and Grahn, 1996). In this paper, the scene is flotation froth. Imaging can be especially useful in applications where it is difficult to obtain the measurements needed for process analysis – froth flotation, for example."

Jan 1, 2006

By Jin Liu

The mechanism and rate of carbon reduction of each of the phases that are formed in the flash flame, i.e. sulfide (matte) and oxysulfide, was investigated. Graphite-slag reduction was conducted for comparison purposes. The objective of these tests was to measure the rate of solid graphite reduction of respectively matte, oxysulfide, slag, and matte+slag mixture at different temperatures. More in particular, these tests were expected to permit understanding and explaining the reduction mechanism of each material by comparing the respective reaction rates, product reaction gas compositions and CO/CO2 ratios, reduced material assays, activation energies, and other relevant parameters. Direct visual inspection of the test crucibles would provide additional information.

Jan 1, 2006

By V. A. Bryukvin

A characteristic feature of the macrokinetics of the interaction process is the presence of two specifically defined areas of oxidation which had a linear time dependence. The effect of variables, such as residual sulphur content of the melt, temperature and the oxidation potential of the gas phase, on the macrokinetics of oxidation are investigated. Phase composition and structure of products of solidification of partially oxidised melts and thermodynamic properties pentaining to Cu-S-O melts are used to analyze the macrokinetic behaviour and mechanisms of the interaction. The process of interaction of sulfide copper melts with oxygen may be considered as a disproportional absorption process and its mechanism is based on localized interaction on the surface and inside the melt volume. Superficial processes include also the process of primary chemisorption of oxygen by melts at place of metal-metal donor bonds proceeding with formation of oxysulfide liquid solutions and volumetric decomposition of the latter accompanied by evolution of sulfur dioxide and metallization of sulfide melts. It is the degree of dynamic balance of such interaction processes that determines specific individual features of the macro-kinetics and mechanism of oxidation of sulfide copper solutions with oxygen in the gas phase.

Jan 1, 2006

By Li Qihou

Mono-disperse ZnS and CdS nano-particles were prepared by the homogenous precipitation method and the effects of SO42-,NO3- and Cl-ions on crystalline of particles were investigated experimentally. The results showed that these anions had no influence on the crystalline of ZnS, but different crystalline CdS ultrafine particles were produced in different anion systems, where the blend-type CdS was obtained from natrate or sulphate solution, and wurtzite-type CdS from chloride solution. It was ascribed to the coordination of Cl- and Cd2+ that altered the supersaturation of precipitate ions in the solution, the existing growth units and their connecting patterns, thereby producing wurtzite-type CdS with a more stable structure.

Jan 1, 2006

By María Cristina Ruiz

In the processing of copper concentrates by the conventional smelting-converting technology, complying with the increasingly severity of environmental legislation in some countries has become difficult, mainly due to severe fugitive emissions of gases produced during the batch PS (Peirce-Smith) converting step. In this work, the results of an investigation on the pressure leaching with sulfuric acid and oxygen of white metal (produced in a Teniente Converter reactor) are discussed. The study was carried out at laboratory scale and the main variables studied were temperature, concentration of sulfuric acid and partial pressure of oxygen. The experimental results indicated that most of the sulfur in the white metal was oxidized to sulfate in the whole range of temperature studied (105ºC to 150 ºC). The concentration of sulfuric acid over 0.05 M, and oxygen partial pressure over 6 atm had little effect on the dissolution of copper from the white metal. On the other hand, temperature had the most significant effect on copper dissolution; below 130 ºC copper dissolution was incomplete after 5 hours of leaching while at 150 ºC the dissolution was complete in 90 minutes and 10 atm of partial pressure of oxygen

Jan 1, 2006

The paper describes the procedure of data inquiry on the structure of mineral production in Austria and selected results. Goal of the endeavor was to gain more tangible insights into the mining industry as a basis for regulation balancing economical, ecological and social aspects.

Jan 1, 2006

By P. Trueman

A project is underway to convert a validated methodology to a system that will permit the near real time interpretation of loading data from longwall powered supports, allowing rapid adaptation of mining strategies, maintenance scheduling and set pressures for optimal roof control. Such a system has the potential to significantly reduce roof control problems and is a pre-requisite to successfully fully automating a longwall face. The development depended upon a robust methodology for interpreting the pressure sensor data coming from the face in the context of support strata interaction using a novel characteristic load cycle analysis concept. New software was developed capable of handling the large quantity of data emanating from a modern longwall with the current level of signal corruption and loss, accurately delineating load cycles and extracting the critical load cycle features essential for interpreting how the support and strata are interacting. Existing software being used to access the pressure data were found either to be incapable of delineating load cycles at all or, where they could, the accuracy was low, making it impractical to use them in combination with the new advances in load cycle analysis. The software is currently being extended from ?off line? to ?on line? in order to provide a real time response to changing strata conditions.

Jan 1, 2006