Search Documents

By Jaroslaw Drelich

This report briefly reviews the measurements and interpretation of adhesion forces measured between microscopic probes and substrates having micro- and nanoscaled roughness characteristics that were recently conducted at Michigan Tech using atomic force microscopy. The laboratory study concentrated on both rigid and deformable materials, with the probes larger than the size of roughness features of interacting surfaces. For such systems, a detailed surface characterization in terms of roughness parameters, asperity size and shape, and spacing between asperities, as well as analysis of deformation of materials is required. Analysis of the experimental data can be done with theoretical models, which are suitable for rough surfaces and therefore allows to normalize the measured forces. Alternatively, loading of the probe during adhesion force measurements can be managed properly to control deformations of the nano-scaled surface irregularities. Controlling the deformation reduces and even eliminates the effects of nano-roughness on the probesubstrate contact area, promoting conditions described by the contact mechanics models for the sphere-smooth substrate system.

Jan 1, 2005

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

By C. Pieper, J. B. Pateiro Fernandez, S. Möllerherm

"Since the United Nations conference on "environment and development" in Rio de Janeiro in 1992, the term "sustainable development" or short "sustainability" is used more and more in social-political discussions. Agenda 21 calls on the countries on national level as well as governmental and non-governmental organisations on international level to develop a concept of sustainability indicators to measure the progress towards sustainability. This paper deals with the development of an evaluation system for sustainability in the minerals extraction. By their application, aspects of sustainable development in the raw minerals industry are to be systematically conceived and assessed. This project has been carried out on behalf of the German Federal Ministry of Economics and Labour."

Jan 1, 2005

By Alain Pecker

The choice of a design concept for a bridge foundation is guided by various factors; several of these factors are indeed of technical origin, like the environmental conditions in a broad sense, but others non technical factors may also have a profound impact on the final design concept. The foundations solutions adopted for the Rion Antirion bridge are described and an attempt is made to pinpoint the major factors that have guided the final choices. The Rion Antirion bridge is exemplar in that respect: the foundation concept combines the simplicity of capacity design, the conceptual facility of construction and enhances the foundation safety. The design of these foundations was a very challenging task which required full cooperation and close interaction with all the parties involved: concessionaire, contractor, designers and design checker.

Jan 1, 2005

By Silas C. Nichols

FHWA Interest is due to: ? An increase in successful projects in the U.S. private sector and in other countries ? Cost effective and more efficient in many circumstances ? Agency Priorities - FHWA "Vital Few" AASHTO TIG

Jan 1, 2005

Standards And Laboratory Monitoring In Gold Assay Key Components Of Best Practice

Jan 1, 2005

By Randy Wheeler

The importance of having full wave form information for recorded blast events cannot be overstated. Knowing the peak particle velocity and the frequency at the peak are the tip of the iceberg. This presentation will focus primarily on using the FFT (fast Fourier transform) for detailed frequency analysis. Employing linear superposition to evaluate timing effects on amplitude and frequency will be discussed.

Jan 1, 2005

By Claude Deveau, Stephen R. Young

Introduction Tanco History Tanco is sometimes known as the Bernic Lake Mine. It is located about 180 km east-northeast of Winnipeg close to the Manitoba-Ontario boundary. Tanco operates an underground mine employing ramp access, room and pillar mining and shaft hoisting for the production of tantalum, lithium and cesium minerals. Tantalum recovery employs conventional gravity and centrifugal concentration methods along with a flotation process which recovers ultra-fine tantalum. All tantalum concentrates are shipped to Cabot Supermetals, Boyertown, Pa., for the production of tantalum chemicals and metals. Tanco also produces lithium products from spodumene ore. The lithium concentrates from Tanco are shipped worldwide for use in ceramics, specialty glass and mold powders. Cesium processing involves the dry grinding of pollucite as feed stock to the on-site chemical plant dedicated to the production of cesium formate, a high density drilling fluid. Tantalum milling operations commenced in 1969. In the early years of the operation, feed grades were three to four times as high as they are today. Coarse-grained tantalum mineralization with complete tantalum liberation at sizes of 300 µm allowed for easy recovery with conventional equipment such as spirals and shaking tables. Over the years, the process and feed material to the plant have drastically changed. Due to drastically reduced liberation sizes, efforts have been made to try to recover as much of the liberated particles as possible in order to maintain acceptable recoveries.

Jan 1, 2005

By L. S. Jeffrey

Estimates for South Africa?s coal recoverable reserves made in 1999range from nine to 59 billion tons; latest estimates by the Minerals Bureau suggest that 33 billion tons is a more likely figure. As much as 70% of that coal is located in the Waterberg, Witbank, and Highveld coalfields, as well as lesser amounts in the Ermelo, Free State and Springbok Flats coalfields. However, the Witbank and Highveld coalfields are approaching exhaustion (estimated 9 billion tons of recoverable coal remaining in each), while the coal quality or mining conditions in the Waterberg, Free State and Springbok Flats coalfields are significant barriers to immediate, conventional exploitation. New extraction technologies, technologies exploiting the energy content of the coal in situ, as well as suitable uses and markets for low-grade, high-ash coal are required before the country can utilize its admittedly vast coal resources. Major challenges for exploiting some Limpopo province coalfields are severe water shortages, insufficiently developed infrastructure, fragile environments and poor roof conditions due to the depth and complex geology. In the Central Basin (Witbank, Highveld and Ermelo coalfields) technical innovations for thin seam extraction, economic mining of both pillar coal and intrusion-fragmented resource blocks and the utilization of lower-grade coals are required. The success of the fluidized bed combustion technology is necessary to utilize the low-grade coals of the Free State and Molteno coalfields, while environmental exemption for past problems, together with strategies for mining small, disjointed thin-seam resource blocks, is required in KwaZulu-Natal. Clean coal technologies, coal cost and quality, environmental considerations, sustainable development, the growth of the South African economy and Government?s regulation of the electricity industry are the main challenges to the continued use of coal as South Africa?s primary energy source.

Jan 1, 2005

By D. J. Kemp

The 20th century saw changes in the mining and metallurgical industry not only technically but also in social and environmental expectations. As projects continue to become larger their visibility raises concerns among many groups. For mining companies, transparency, openness, and early engagement of all parties are fundamental to assure success. An equally important task is to anticipate the standards that will be required to meet society’s expectations in the 21st century.

Jan 1, 2005

By J. F. Adams, V. G. Papangelakis

Chemical modelling is becoming increasingly useful in the development, analysis, design, and control of hydrometallurgical processes. The paper presents the development of reliable databases for chemical modelling of selected hydrometallurgical systems using state-of-the-art software, such as OLI. The modelling strategies are also demonstrated. The high pressure acid leaching (HP AL) of laterites, oxygen solubility in the oxidative leaching process of zinc sulfide, gypsum solubility and lead chemistry in mixed sulfate-chloride solutions are presented as case studies. This on-going work attempts to bridge the gap between theoretical research and industry needs. Computational Analysis in Hydrometallurgy 35th Annual Hydrometallurgy Meeting held in conjunction with the 44th Annual Conference of Metallurgists ofCIM Calgary, Alberta, Canada Edited by

Jan 1, 2005

By S. C. Livanou, S. P. Tampouris, E. N. Zevgolis

In ferronickel (Fe-Ni) production from oxidized nickeliferous ores, mechanical losses of ferronickel in the slag are reduced by magnetic separation. Slag from the electric furnaces (E/Fs) contains 0.16% Ni. Its magnetic separation gave a pre-concentrate with 0.76% Ni, weighing approximately 6.5% of the feed. Nickel recovery was 29.7%. This pre-concentrate was then treated in a second (concentration) plant. Concentration treatment involves screening, crushing and magnetic separation. A pre-concentrate with 0.76% Ni gave a magnetic concentrate with 2.58% Ni and a non¬magnetic part with 0.35% Ni. Smelting of the non-magnetic part without the addition of a reduction agent in a laboratory electric arc furnace, gave a ferronickel alloy with approximately 20% Ni and a slag with 0.16% Ni.

Jan 1, 2005

By Andrea Koschinsky

Numerous hydrothermal vents occur along the Earth?s oceanic spreading axes documenting the reaction of seawater with hot magmatic rocks. The circulation of seawater through the oceanic crust, the interaction with hot rocks in the crust, and the subsequent discharge of hot metal- and gas-rich fluids into the ocean have significant implications for the cycling of material and energy on Earth. Until recently, hydrothermal activity was unknown from the Mid-Atlantic Ridge (MAR) south of the Equator where the MAR is offset by about 1000 km at the St. Paul?s and Romanche fracture zones. During a British cruise in February/March 2005, the first active hydrothermal vent field was discovered on the southern MAR at 5°S. During our follow-up cruise M64/1 in April 2005, the first samples from this vent field were recovered with the ROV QUEST (Univ. Bremen) and analyzed onboard. The high-temperature vent field is situated in a water depth of 2990 m along a line of collapse pits within a large basaltic sheet flow. A diffuse, low-temperature field occurs in a jumbled sheet flow few hundred meters to the east with warm water streaming out of cavities between lava blocks. Here we show for the first time that boiling fluids of ~400°C are emanating from sulfide-bearing vents at a depth of about 3000 m at a slow-spreading Mid-Atlantic Ridge segment. Although this segment is composed of thick basaltic crust, these fluids are dominated by hydrogen relative to methane. Whereas the active chimneys consist of pyrrhotite, chalcopyrite, and isocubanite, the mineral association hematite-magnetite-pyrite occurs in the inactive chimneys suggesting that the fluids became more reducing in present times. The high hydrogen contents and the high temperature of the fluids as well as the change to more reducing conditions are most likely related to a young volcanic eruption event some 300 m east of the hydrothermal field. The presence of hematite and magnetite may indicate that the upflow zone or even the reaction zone at 5°S used to be more oxidized then at other MOR sites, where the hydrothermal fluids are commonly buffered by the pyrite-pyrrhotite-magnetite (PPM) buffer. Consequently, high iron contents and high hydrogen/methane ratios occur in high temperature fluids from basaltic host rocks rather than being restricted to ultramafic host rocks. Faunal communities at the South Atlantic vents largely resemble those from the North Atlantic vents implying that the large Equatorial fracture zones do not inhibit or obstruct faunal exchange along the Mid-Atlantic Ridge.

Jan 1, 2005

By K. N. Panigrahi

India bestowed with 6000km of the coastal belt, contains some of the richest and largest placer deposits with a mixture of heavy minerals like ilmenite, rutile, leucoxene, zircon, monazite, sillimanite and garnet. Each of the minerals is having economic value due to its inherent characteristics for industrial use in fields of paints, metallurgy, refractory, abrasive and so on. The reserves of titanium bearing minerals (ilmenite, leucoxene, and rutile) in the country is around 378 million tonnes. More than 90% of the titanium based minerals produced worldwide are utilised for making value added products in the pigment industries. Approximately 8 million tonnes of monazite reserves are available in the country from which several rare earth elements like cerium, neodymium, lanthanum, yttrium etc. can be extracted for use in several industries. The country contains a deposit of about 20 million tonnes of zircon, which is used in foundries, refractories, ceramics and chemicals. India has a reserve of 107 million tonnes of garnet and 131 million tonnes of sillimanite required for the abrasive and refractory industries respectively. Keeping in view the multifarious uses, the beach sand minerals are being exploited to have the economic growth of the nation. Although the process adopted for the separations are simple, the equipment involved are specially designed because of the nature of the material of construction. Starting from the spirals to magnetic separators, all equipments are manufactured outside India, which is not only costly, but the availability also takes much time for fulfilling the import formalities. Unlike open cast mining, beach sand mining is a environment friendly mining because dredging is implemented to cut and pump the loose sand through a slurry pump causing less damage to the surface topography as both mining and backfilling takes place simultaneously. Therefore all out efforts are made to explore the beach sand placer deposits in an economic manner to emerge as a leader in the global mineral industries.

Jan 1, 2005

By M. M. Manamela

Paper written on project work carried out at the University of Pretoria in partial fulfilment of the requirements of the B Tech degree at the Tshwane University of Technology This work tested whether ore particle size affects the carbon-based pre-reduction of titaniferous magnetite. Pre-reduction is performed at a temperature of some 1100°C in a rotary kiln, in the Highveld Steel process. Laboratory isothermal reduction measurements were performed with ore-coal mixtures at this temperature, to test the effect of ore particle size. The results show that size does limit the degree of reduction for particles larger than 15 mm.

Jan 1, 2005

By Murali M. Gadde, Syd S. Peng, C. T. Holland

Cutter roof failure is one of the most common ground control problems affecting the safety and economy of an underground coal mine operation. Several attempts were made in the past to understand the processes responsible for cutter development and to devise mitigating measures. Yet, many cutter failures still happen and their advance prediction remains as elusive as before. One of the reasons for the impasse in predicting cutters lies in the limitations of the current numerical modeling technologies. The development and propagation of cutters is a progressive phenomenon and continuum models can only approximate this process. Since the discontinuum modeling is severely restricted by the lack of reliable input data, alternatives must be sought to better understand cutter failures using the continuum models. This paper proposes one approach using strain-softening material model to simulate the cutter initiation and propagation process. An attempt has also been made to provide some insights into the reasons for the change in cutter location at different parts of a development layout.

Jan 1, 2005

By J. O. Voigt

No major changes took place in the salt industry during 2004. No new uses of salt appeared and only localized supply disruptions occurred. Many salt producers reported slightly increased salt sales and profits for the year. In the United States, about half of the salt supply is produced as brine, by solution mining, and is used by the chemicals industry. One-third of U.S. salt is produced as rock salt by 14 underground mines. The remaining two production techniques, each with less than 10 percent of the total tonnage, are vacuum-pan-evaporation for refined, food-grade salt, and solar pond crystallized salt.

Jan 1, 2005

By Scott Dodds

"The Oxford Hydroelectric Station was a unique project that incorporated a variety of dam strengthening methods to stabilize the facility in order to meet the standards required by Federal Energy Regulatory Commission (FERC). The dam stability and Probable Maximum Flood (PMF) remediation work consisted of (1) construction of a new emergency spillway; (2) installation of 75 high capacity rock anchors; (3) construction of an anchored concrete powerhouse buttress; (4) construction of cast-in-place and sheetpile flood walls; and (5) design and construction of a permanent soil nail wall. INTRODUCTIONThe Oxford Hydroelectric Station is one of 11 hydroelectric facilities owned and operated by Duke Power along the Catawba/Wateree River. The Catawba River originates in the foothills of the Appalachian Mountains just west of Morganton, North Carolina. The river flows east out of the mountains and, at a point just below the Oxford Dam, the Catawba River turns and heads southeast. The Catawba River continues to flow southeast past Charlotte and into South Carolina where it eventually becomes the Wateree River. The Wateree River eventually flows in to the Atlantic Ocean.Located a few miles east of Hickory, North Carolina, the Oxford Dam and Hydroelectric facility is in the upper reach of the Catawba River. Oxford Dam creates the third impoundment along the river known as Lake Hickory. Lake Hickory is well known locally for providing many outdoor activities such as boating, jet skiing, canoeing and fishing. The dam and powerhouse were put into operation in the spring of 1928.Key features of the dam include a short embankment section on the south end of the structure, a 391-foot (119m) long south bulkhead and powerhouse, 540-foot (165m) long gated spillway section and a 235-foot (71.6m) long north bulkhead. The maximum height of the dam is approximately 100-feet (30m) from the crest to the dam/rock interface. (See Figure 1).The work associated with this project is the result of licensing requirements of the Federal Energy Regulatory Commission (FERC) which mandates that all hydroelectric facilities have the capacity to safely discharge runoff created by a critical rainfall event defined as the probable maximum flood (PMF). Duke Power, a division of Duke Energy (DUKE) submitted an initial PMF report in 1992 which indicated that at the Oxford Dam would be overtopped by approximately 10-feet of water during the modeled PMF event. Given the duration and depth of the overtopping, significant damage to the facility and a possible breach could result. Therefore, modifications to the existing facility were necessary to satisfy the report of the PMF model."

Jan 1, 2005

By B. Voyzelle

The deterioration of highway and bridge infrastructure has received considerable attention in recent years because of the billions of dollars needed for repair and rehabilitation. A major factor contributing to this problem is the corrosion of steel reinforcement. Reinforcing steels with good corrosion resistance and relatively low price are therefore essential for maintenance, cost reduction and service-life extension of the steel-reinforced structures. This article describes the development of low-alloying steels that offers good corrosion resistance with reasonably low cost. Topics include steel microstructures, mechanical properties, corrosion performance, industrial applications and economic aspects.

Jan 1, 2005

By W Lu, D Wang

Study of coal oxidation at low temperatures forms the basis of investigating the inherent properties of spontaneous combustion of coal. In general, the process of coal oxidation at low temperatures is very complex, involving many factors. Experiments examining the properties of oxidation and ignition of coal have been carried out. Based upon the results of these experiments, the catastrophe properties in the process of coal oxidation are analysed and the mechanism of catastrophe is proved for the ignition of coal. A folding catastrophe model is also established for the process of coal oxidation. Results obtained show that the process of coal oxidation to ignition is discontinuous, where the coal-environment system yields structure destabilisation. The system can jump from one stable attractor to another. The research results presented in this paper help to show the irregularities of coal oxidation at low temperatures and how to pursue effective control measures.

Jan 1, 2005