Search Documents

By Murali Gadde

Numerical simulation of cutter roof failure is a daunting coal mine excavation design issue. The complex progressive failure mechanisms associated with cutter failures are extremely difficult to replicate in computer models. However, this paper shows that with a proper selection of constitute behavior and implementation of cutting sequence, it is possible to realistically reproduce cutter failure using continuum models. Strain-softening material behavior and a systematic step-by-step model solving for a four-entry-and- three-crosscut model produced results that are similar to cutter patterns noticed in field. These results show that traditional modeling with geometries created in one model-step has limited applicability and may even provide misleading conclusions under some circumstances. Most importantly, the proposed modeling methodology provided some insights into the reasons for the inconsistent spatial distribution of cutters often noticed in coal mines. The modeling also revealed the usefulness of cutter mapping to determine the directions of in situ horizontal stresses.

Jan 1, 2005

By A N. Terblanche, D S. Smit

The paper discusses the improvements achieved after an external sparger flotation column, 1.42 m diameter by 9.5 m high, was installed as a re-recleaner unit at the Northam Platinum LtdÆs UG 2 plant in South Africa. The paper also evaluates the pilot plant data prior to the industrial size column installation as well as the accuracy of scale up from pilot to full-scale operation. Since the installation of the PrepQuip flotation column, the final concentrate upgrade ratio improved from 83 to 105, the 3PGM+Auå recovery improved from 79.7 per cent to 81 per cent and the Cr2O3 content in the final concentrate decreased from five per cent to 2.8 per cent. The upgrade ratio can be improved to 125 with an overall 3PGM+Au recovery of 80 per cent. Conventional mechanically agitated flotation cells achieved only 74 per cent recovery at an upgrade ratio of 125.

Jan 1, 2005

By Richard J. Mainiero, Michael J. Sapko, Marcia L. Harris

Since 1988, there have been thirteen documented incidents in the United States and Canada in which carbon monoxide (CO) is suspected to have migrated through near surface strata into structures or other enclosed spaces as a result of nearby trench blasting or surface mine blasting. From these incidents, there are thirty suspected or medically verified CO poisonings and one fatality associated with these incidents. To better understand the variables contributing to this hazard, the National Institute for Occupational Safety and Health (NIOSH) carried out a small- scale field study to identify key factors that may contribute to the migration of CO through the ground. NIOSH conducted single- hole heavily confined experimental test shots to measure the radial pressure pulse as it propagated through surrounding monitoring holes to determine if a relationship existed between the pressure pulse and resulting CO measurements afterwards. NIOSH also monitored blasts at an airport construction site. Following the detonations, the concentrations of CO, nitric oxide (NO), and nitrogen dioxide (NO2) were monitored for several days in the surrounding satellite holes. The peak CO measurements relative to distances from the shots were compared. Pressure histories and peak particle velocities (PPV) were measured at monitoring boreholes. It was found that the differential pressures recorded within the boreholes give some indication as to the likelihood of CO appearing, whereas the PPV measurements do not seem to be as good an indicator for potential CO migration. In this limited study, changes in barometric pressure had very little influence on removing the trapped detonation products, whereas applying a vacuum to the monitoring holes was effective in reducing the entrapped CO concentration.

Jan 1, 2005

By Donald A. Bruce

Pregrouting is an extremely important part of many rock tunneling projects. However, poor and unsatisfactory performances have been frequently recorded often with very severe consequences, technically and financially. This paper, based on personal knowledge of several relevant case histories, provides recommendations with respect to specification drafting, drilling, water pressure testing, and grouting methodologies, and cementitious grout mix design principles. Even given that the logistical challenges facing tunnel pregrouting from underground will prevent all the sophistication and innovations of contemporary dam foundation grouting being practically implemented, there is still opportunity and need to change “traditional” approaches.

Jan 1, 2005

By V. Loya

Metallic foams (MF) are relatively new materials with a combination of attractive properties (permeability, high surface area, thermal and chemical stability, etc,), They can be produced from different materials and can be manufactured using various processes, Due to their unique properties, they find applications in different sectors of engineering, such as energy absorption, filtration, heat dissipation, etc, For many applications, the permeability is an important parameter to characterize and optimize, Most of the recent literature on the subject studied the permeability in the low velocity range. The present study was carried out to have a better understanding of permeability for greater velocity ranges, An equipment was designed and built for this purpose, Pressure drop measurements were made across the thickness of open-cell nickel foams, Pore and window sizes were measured by image analysis on SEM micrographs, The experimental results are in relatively good agreement with the Hazen-Dupuit-Darcy model (R2>98%), The permeability is affected by pore size, porosity and the normalized projected area of the connecting pores (ie. windows).

Jan 1, 2005

By William A. Enrico

Umicore acquired the Pirdop Smelter in a privatization offering by the Bulgarian government in September 1997. Since that time, an investment program has been conducted to increase capacity to 225 000 tons per year of anode copper, while improving the environmental performance to meet Bulgarian and European standards. A significant part of this investment program involved reconstruction of the three Peirce-Smith converters and the associated gas handling system. During the period June, 2000 through April, 2002, converter capacity was increased, the existing water-cooled hoods were replaced, the waste heat boiler was replaced by two evaporative coolers, the dry ESP's were rebuilt and extended, and a Converter Control System (CCS) installed. From 2002 until the present, a continuous improvement of operating and environmental performance has been achieved. This paper will describe the converter reconstruction project, the operational, maintenance, and environmental improvements achieved since then and additional projects presently under consideration.

Jan 1, 2005

By M. J. Nicol, C. van Wensveen

The kinetics of the oxidation of thiosulfate by copper(I I) in ammoniacal solutions have been studied in the presence and absence of dissolved oxygen. The formation of an intermediate mixed ammine/thiosulfate copper(II) complex ion has been confirmed and the rate of the reaction monitored by simultaneous on-line spectrophotometric, dissolved oxygen and potentiometric measurements. The rate of the anaerobic oxidation of thiosulfate by copper(II) was found to be orders of magnitude slower than that in the presence of dissolved oxygen and is inhibited in the presence of ammonia and anions such as sulfate and chloride as a result of competition with thiosulfate for the axial coordination sites on the copper(II) tetrammine complex. In the presence of dissolved oxygen, it was found that the copper(I) thiosulfate complexes are only very slowly oxidized while the copper(I) diammine complex is rapidly reoxidised to the copper(II) state. Thus, the initial rapid reaction with copper(II) leads to a pseudo steady-state condition in which the concentration of copper(I) is relatively constant and the rate of oxidation of thiosulfate can be predicted from the measured rate of oxidation of copper(I) by oxygen in ammoniacal solutions. The effects of the concentrations of ammonia and thiosulfate on the oxidation rate can be rationalized on the basis of the above coupled to the species distribution of copper(I) in the ammonia/thiosulfate system. It is shown that, with relatively simple measurements of dissolved oxygen and copper concentrations, the rate of oxidation of thiosulfate can be predicted under typical leaching conditions.

Jan 1, 2005

By N F. Fraser

Seafield ResourcesÆ offshore placer gold project covers c.10 000 km2 of the Westland continental shelf between Karamea and Jacksons Head, from the low-water mark out to the 120 m isobath (Figure 1). De Beers Marine (DBM), the marine diamond subsidiary of the De Beers Group, will carry out the project with geological input from Placer Solutions (PSL). DBM bring a wealth of expertise and advanced technology to the project, developed during their 20 years of exploration and mining of diamond placers on the Atlantic shelf of southern Africa, where they have also maintained a strong environmental record.   Glaciers and high-energy rivers emanating from the Southern Alps have transported substantial quantities of gold bearing sediment onto the Westland continental shelf during Pleistocene glacial periods, when fluvial gradients are steeper, sea level is c.120 m lower and most of the shelf is exposed. These deposits have been extensively reworked by the advancing shoreline and marine processes during interglacial marine transgressions, and most are now buried beneath a variable thickness of post-glacial marine sand, silt and mud. DBM will use side-scan sonar, swath bathymetry, Chirp sub-bottom profiling and a magnetometer to map the sea floor and sediments beneath it, guided by PSLÆs predictive geological model for gold distribution on the shelf. Cactus grab and vibro-core samples will be used to ground-truth the geophysics and provide stratigraphic, sedimentological and gold distribution data for incorporation into the geological model. Areas of interest identified by the geophysical and sampling data will be investigated in more detail, with closer-spaced geophysics and Mega-drill sampling to a maximum sediment depth of 20 m beneath the sea floor. These samples will be raised to the ship with air-lift suction technology, processed onboard for mineralogical and grade information, then returned to the sea floor. Environmental baseline data will be gathered from Van Veen grab samples of seabed sediment taken throughout the area during the prospecting programme.

Jan 1, 2005

By T Baard, A Pieters

This paper deals with the design and implementation of a 17 MW (nominal) surface cooling installation at Impala Platinum No 14 shaft located in Rustenburg, North West Province, South Africa.The cooling requirements included the installation of a surface ammonia refrigeration plant complete with the storage of hot and cold mine service water for underground use. It was also necessary to install a surface bulk air-cooling facility, which cools 400 kg/s of ventilation air going to the underground workings. Primary cooling is to the surface bulk air cooler. The cooling duty of a surface bulk air cooler is heavily dependent on the ambient wet-bulb temperature. Because of the daily wet-bulb temperature variation in this part of the world, use was made of a cold thermal storage facility of four million litres. The excess chilled water is stored during the night, for use by the main drilling shift during the day. This keeps the refrigeration machines as close as possible to full load during the summer, thus maximising the use of the capital expenditure. This paper discusses the control philosophy used to maximise the cooling output, as well as the thermal process. The project consisted of two phases resulting from the underground development phases of the mine. The first phase started in January 1999 and was commissioned by the end of the same year in record time. The final commissioning of the second phase took place at the end of 2002. The most difficult part of the construction phase was the tunnelling of a subsurface air duct from the bulk air cooler to the operating vertical shaft. This was done without disruption to the hoisting of men, material and ore in the shaft. Owing to the size of the refrigeration machines, the ammonia quantities involved and the application on a mine (no ammonia can go underground, either in the service water or in the mine air) special precautions had to be taken. South Africa has developed high standards for ammonia refrigeration plants used on mines, which will be partially dealt with in this paper.

Jan 1, 2005

The basic rule for correct design of a sample plant is that all parts of the material being sampled must have an equal probability of being collected and becoming part of the final sample for analysis. However, this rule is often ignored in the design of sample plants to save capital costs. This is false economy, because the samples taken are likely to be seriously biased and the precision may be compromised. The introduction of bias is particularly serious, because no amount of replicate sampling and analysis will reduce bias once it is present and it is often quite difficult and expensive to subsequently rectify the problem due to space limitations around the primary sampling location. This is also true of secondary and tertiary sampling stages, particularly in terms of the relationship between particle size and retained sample mass. The best strategy is to seek expert sampling advice and design the sample plant correctly at the outset.

Jan 1, 2005

By Jose A. Delgadillo

The hydrocyclone problem has been a challenging task for the last 30 years. In the 80’s and 90’s Computational Fluid Dynamics solution to this problem began to appear. These were unsuccessful due to over simplification. In the past 3 dimensional solution with ?-e model and Reynolds Stress Model have been published. In this paper RSM and ?-e models are compared with velocity profiles measured in 75 mm and 250 mm diameter hydrocyclones. It is shown that results are not satisfactory with RSM or ?-e and that a model called Large Eddy Simulation is needed to describe velocity profile evolution and size classification.

Jan 1, 2005

By W. J. Dick, K. G. Kress

A pipeline syphon can be a simple and reliable alternative for water conveyance as compared to otherwise more complex pumping systems or low-level outlet conduits through earthfill dams. In a simple form, it consists of a pipeline constructed over the top of a dam or other high topographic feature, connecting a source pond to a receiving pond or channel (Fig. 1). The syphon action is initiated by removing air from the pipeline (priming) using water pumps, vacuum trucks, or simple devices that can be purchased “off-the-shelf.” Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate, or other devices. Repriming is not required even if the flow is stopped, provided the syphon was not drained. A limiting factor in considering a pipeline syphon as a design option is the maximum lift (i.e. vertical distance from source pond water level to summit of pipeline syphon) which is approximately 9 m or less, depending on pipeline syphon features and site conditions. A pipeline syphon can be quickly constructed from readily available materials including steel, concrete, polyethylene, or PVC pipe. It is particularly well suited to many of the unique conditions often encountered at mine sites. This paper identifies situations that can sometimes be best resolved using a pipeline syphon. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

Jan 1, 2005

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By R. D. Sharpe

Gypsum wallboard manufacturers in the United States shipped 3.18 billion m2 (34.2 billion sq ft) of wall-board products during 2004 versus 2.93 billion m2 (31.5billion sq ft) in 2003. Following a historic high production of gypsum wallboard products in 1999, production decreased in 2000. But it has steadily increased during2001 through 2004. Wallboard production in the United States increased about 8.6 percent in 2004 from 2003. Following several years of a “building boom” of new wallboard plants and the expansion of the manufacturing capacity of several existing plants, 2004 was a relatively quiet year. However, several new plants and capacity expansions were announced or are in progress during 2004.

Jan 1, 2005

By Y. Chengxian

Many factors about the HIC (hydrogen-induced cracking) resistance of pipelines are discussed in this paper. The main factors that influence the ability of HIC are environmental and material factors. The chemical compositions, non-metal inclusions and microstructure are discussed in detail, while a group of tests on HIC resistance are done according to varying C, S, Mn and P contents in pipeline steels, different experiment time and different strength to the coupon. It is concluded that decreasing the amount of C and S can obtain good HIC resistance; the test time has an effect on the different microstructure of X70; microstructure is the most sensitive factor for the initiation processes of HIC.

Jan 1, 2005

By D Hill

In the Ngakuru area zeolite deposits occur in late Quaternary lacustrine vitric tuffs of the Ngakuru Formation and two of the deposits are being mined. The Ngakuru Formation overlies the Ohakuri Ignimbrite dated at c. 240 ka, and is overlain by younger alluvial sands and gravels. Individual zeolite deposits contain 50 - 80 per cent zeolite over a thickness of up to 45 m in thinly stratified vitric tuffs and are localised along NE-trending normal faults. Glass shards in the tuffs are replaced by the silica-rich zeolites mordenite and clinoptilolite. Amorphous silica (opal A), opal-CT, Kfeldspar and smectite are also present. The zeolites and other minerals are very fine grained (<10 8m), with open meshes of crystals that result in high porosities (52 - 70 per cent) in mordenite-rich tuffs. Zeolitic tuff samples typically have cation exchange capacities of 80 to 110 meq/100 g and internal surface areas of 25 - 58 m2/g, which combine to give high liquid and odour absorption capacities. The first zeolite deposit (Mangatete) was found in 1992, and this and the Twist Road deposit are worked by quarry benching into the side of hills. The zeolitic tuffs are dried and crushed to produce a variety of products including adsorbents for soaking up oil/chemical spills and animal wastes, animal feed supplements, water treatment, and sports turf and slow release fertiliser. The Ngakuru zeolite deposits formed at shallow depth (<100 m) along fault zones from reaction of glass-rich tuff beds with groundwater-diluted geothermal water during the late Quaternary, and are as young as 8500 yr BP from 14C dating of plant material in sinter associated with the Mangatete deposit.

Jan 1, 2005

Brisbane based and listed on the ASX, Eastern Corp is pursuing the development of coal projects in New Zealand. There are various reasons why New Zealand coals are of interest û substantial resources, stable political/economic environment, close to Asian markets. In just over 12 months, Eastern has secured an operating coal mine (Cascade) and a prospective exploration area (Whareatea West), both on the Denniston plateau region, on the south islandÆs west coast. A key focus of activities is the development of relationships with key stakeholders and the promotion of the local economy.   Certain barriers may exist to the entrance by foreign companies into the New Zealand coal mining sector. These include geological challenges provided by the heavy faulting of the coals, port and rail infrastructure constraints, and the ægreenÆ factor.

Jan 1, 2005

By Patrick Pelletier, Pierre-Alexandre Bossé, Julie Fournier, Gianni Bartolacci, Jayson Tessier, Ahmed Bouajila, Carl Duchesne

"This paper summarizes research into the study of the control of flotation processes based on froth images. The use of numerical image analysis techniques for the extraction of significant patterns (froth structure and colour) from industrial flotation froths is discussed.First, the froth was analysed by the use of the Multivariate Image Analysis (MIA) method to extract the spectral variation contained in a RBG image. The Partial Least Squares (PLS) was applied to develop the empirical model for the prediction of froth grade. The results of this application are illustrated using one industrial case study.Second, the froth was also analysed by Gray Level Co-occurrence Matrix (GLCM) and Wavelet Transform Analysis (WTA) to extract features related more to morphological aspects. Since there is useful information hidden in froth texture, these methods are used as texture descriptor to classify different types of froths.Third, a control strategy based on a froth structure indicator was developed and implemented on an industrial zinc flotation circuit. The feedback controller uses a reagent flow-rate in order to maintain the froth structure at its set point. Process improvements obtained with the implemented control strategy are highlighted.Finally, the feasibility to implement a hybrid control strategy consisting in a froth structure supervision controller based on the froth concentrate grade estimated by MIA and recovery inferred by image analysis is discussed.INTRODUCTIONThe development of control strategies to achieve satisfactory control performance has always been a great challenge for engineers and the need for improved process diagnosis, control and optimization has become more and more evident for the mineral processing industry in the last decades. That is why new process variables need to be measured particularly in highly multivariable processes such as flotation. This industrial process is subject to a wide variety of disturbances mainly generated by frequent and sometimes abrupt changes in physical and/or chemical ore characteristics and also, due to some irregularities in manual process operating procedures. A flotation circuit scheme is always a complex network of more than two dozens slurry streams. Information about those streams (% solid, metal content analysis and flow rates) is important for process diagnosis performance evaluation and control. Also, because of the grade decrease and increasing complexity of the new processed ores, more instrumentation outputs and more powerful and significant pr"

Jan 1, 2005

Scale build-up in titanium palladium alloy spent electrolyte heat exchangers in the residue treatment plant commissioned at Risdon, Tasmania in 1971 was shown to be a mixture of manganese dioxide and anhydrite (CaSO4). The manganese dioxide was deposited as a result of thermal decomposition of permanganate ions present in the spent electrolyte. It was shown that deposition of manganese dioxide and associated anhydrite scale could be prevented by prior reduction of permanganate ions to the manganous (Mn++) state by the addition of ferrous ions. In the plant this was conveniently accomplished by injecting into the inlet line to the heat exchangers sufficient zinc plant solution containing ferrous sulfate to decolourise the spent electrolyte. This action prevented deposition of such scale for another 21 years, until the heaters were finally decommissioned in March 1992. Measurements indicated that addition of the reducing solution lowered the anodic potential of the titanium alloy by 200 - 300 mV (depending on the solution resistance), but that it was still +300 to 400 mV with respect to a standard calomel electrode. It was shown that, if necessary, a small impressed current could be applied to provide anodic protection. Before scale deposition was overcome by the addition of ferrous sulfate solution, badly scaled heat exchangers were cleaned by recirculating a solution of hydrogen peroxide in spent electrolyte or dilute aqueous sulfuric acid, after laboratory testing of a variety of possible solvents for the scale. Corrosion tests indicated that attack on the titanium alloy by the acidic peroxide cleaning solution was insignificant.

Jan 1, 2005

By N. R. Andrade-Gonzalez

In this paper, the effect of magnesium and strontium additions on the heat treatment behaviour of cast A319,2 alloy was investigated, Permanent mold samples were heat treated at 495 °C for 4 and 24 h, then quenched in hot water and aged at 180 °C and 220 °C for different temperatures, It is found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu alloys, mainly when Mg and Mg-Sr are added, The results of electron probe microanalysis (EPMA) observations reveal that the age-hardening behaviour is related to the precipitation sequence of alloys, For the Al-Si-Cu alloy, the first aging peak is the result of the high-density GP zones, while the subsequent peaks arise from metastable phases, Obvious intervals during the transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks, It is seen that addition of Mg (-0,40 wt %) leads to the precipitation of coarse Al5Mg8SioCu2 particles. When modifying the high Mg alloys, Cu-intermetallics segregate in areas away from the growing Al-Si eutectic regions, Modification with strontium retards the precipitation of the silicon out of the matrix.

Jan 1, 2005