Search Documents

By R. L. Virta

Common clay is a natural, fine-grained material composed of hydrous aluminum silicates. Shale is a laminated sedimentary rock that is formed by the consolidation of clay, mud or silt. Production About 160 companies produced common clay and shale in 41 states. In states not reporting production, common clay and shale probably was mined and sold for construction applications by companies not participating in the U.S. Geological Survey’s canvass of producers.

Jan 1, 2005

By Paul Laframboise, Nigel MacDonald, Mike Hallewell, Robert Thorpe

"Galmoy Mine, owned by Arcon Mines Limited, has operated since 1997, and is one of three operating lead/zinc mines in Ireland. Changes in ore type starting in mid 2002 created challenges to metallurgical operations at Galmoy. This resulted in unacceptable lead and zinc flotation performance, which prompted initiation of a formal plant review and a subsequent stabilization programme. This involved a structured review of operational practices, development of a new Standard Operating Procedure (SOP) which in turn led to significant changes in process control equipment needs in conjunction with extension of zinc flotation cell residence time.This paper will describe the metallurgy of the Galmoy operation. Reasons for the poor metallurgy experienced in 2002 will be described, as well as the solutions identified to overcome these problems. By the second quarter of 2003, these solutions had been implemented and recoveries had risen to record levels.INTRODUCTIONGeneralGalmoy Concentrator is located in County Kilkenny (Refer to Figure 1 below) and was constructed during 1996 and commissioned in 1997.The concentrator at Galmoy had been designed initially to treat 650,000 tonnes per annum of primarily CW ore type. The main mineral of economic significance was sphalerite (Typically 10 to 11% Zn) with some minor galena (0.7%Pb) in a dolomite (Magnesium Carbonate) host rock.The only other competing sulphide mineral was pyrite (Circa 3 to 5% Fe in Mill Feed. This CW ore type predominated the first 6 years of production, but in August 2002, the ore mineralogy changed due to significantly higher levels of pyrite rich G ore body being blended in with CW ore."

Jan 1, 2005

By K. Poorhaydari, B. M. Patchett, D. G. Ivey

In this paper, some applications of carbon extraction replicas, as samples for transmission electron microscopy (TEM), are discussed. Modern high strength microalloyed (HSMA) steels, used as structural or pipeline materials, have very small grains with substructures. Replicas used in TEM can resolve the grain boundaries and can be used for grain size measurements in cases where the small size of the grains pushes the resolution of conventional optical microscopes. The grain size variations obtained from replicas correlated very well with mechanical property variations, indicated by hardness, in the fine-grained heat-affected zone and base metal of some welded HSMA steels. Replicas are also very suitable samples for precipitate examination with analytical TEM. Advantages and limitations of the application of replicas, as well as some corrections for the estimation of the volume fraction of fine precipitates, are discussed.

Jan 1, 2005

By K. Adham, C. Lee

The demand for nickel is continuing to exceed inventories, and producers are working vigorously to increase capacity. Many nickel processes utilize the fluidized bed technology for its fast heat and mass transfer, excellent temperature control and low maintenance. The following four nickel applications of the fluidized bed technology have been commercialized: I) Sulfide ore roasting; II) Nickel sulfide (matte) roasting; III) Nickel oxide reduction; IV) Nickel chloride pyrohydrolysis. This paper examines the issues surrounding the application of fluidization technology to the above processes, from the stand point of the engineer modeling the process and designing the key equipment, based on the historical success stories and the fundamental principles of flow sheet synthesis. Using the available data in open literature, typical flow diagrams (with convenient bases of 1 t/h feed or product) are developed to illustrate the relative flow rates and to highlight the key features of each application. In addition, some historical background information is provided for each process with supplemental notes with regards to our company's involvements.

Jan 1, 2005

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By ?. V. Kabanov

n considered operation hydraulic and kinematic circuits of deep-water installation for sampling a ground from a sea-bottom are submitted. Control by setters is made remotely from a service station with the help of a system of telemechanics. Migration of apparatus along a bottom is ensured with the help of force of a response of a jet and Archimedean force. The mathematical exposition of the device composed and computer simulation is Design parameters are defined and static performances are obtained. Operation is in a stage of manufacture of working drawings. There are patents of Russia.

Jan 1, 2005

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Josh Struble, Fu Yuet, Jan Zywiel, Kevin King

This paper discusses the application of Integrated Inertial/GPS technology for position determination of earthmoving equipment in an open-pit mine. Different GPS augmentation methodologies are introduced and discussed. Principles for the operation of the Applanix POS MC (Position and Orientation System for Machine Control) are also presented, together with test results conducted at the Twin Creeks Newmont mine, using the POS MC and Caterpillar’s CAES (Computer Aided Earthmoving System).

Jan 1, 2005

By I Jabou, D G. Blazak, L C. S Hogarth

The R70 test is a good indicator of coal reactivity to oxygen and is commonly used to provide a rating of propensity for self-heating. Tests performed by The University of Queensland Spontaneous Combustion Testing Laboratory have resulted in the development of a large database that shows the impact of coal quality on this parameter. From these results it is possible to infer an R70 value, which can be used to gain an appreciation of the intrinsic coal reactivity before it is even tested. However, any interpretation of R70 values must consider the influences of coal rank, mineral matter and moisture content to provide a better understanding of the spontaneous combustion risk of a particular coal.

Jan 1, 2005

By D. Goodings, W. L. Fourney, Bonenberger, R., Uli Leiste

The Dynamics Effects Laboratory at the University of Maryland conducted a series of very small scale tests to measure the impulse delivered to a plate by the detonation of an explosive charge which was buried in saturated sand. These tests were conducted to support a full scale tests series being supported by the Navy (NSWC Indian Head Division) to learn more about loads applied to structures by explosive detonation. For each of the tests being predicted, a series of three tests were conducted at Maryland, one with a 0.203 gm charge, one with a .609 gm charge, and one with a 3.3 gm charge. A high speed digital camera (500 frames per second) was used to record the displacement of the plate as a function of time. From this the initial velocity of the plate was determined and then the impulse delivered to the plate by the explosive. A best fit line through the data was determined for the three model tests conducted and this equation was used to extrapolate the predicted impulse for the full scale tests.

Jan 1, 2005

By G. P. Gu, B. Fang, R. W. Revie, M. Elboujdaini

Stress-corrosion cracking (SCC) tests were conducted in the near-neutral pH standard solution, NS4, and in an actual soil solution, using four-point bending at high a stress ratio and low frequency conditions very similar to those of operational pipelines. Pitting incubation appeared first and then pitting initiated and grew in both solutions although there were many more pits on the specimen tested in soil purged with 5% CO2 + 95% N2 than in the specimen tested in NS4 solution purged with the same gas. These observations show that samples in soil solution are more susceptible to pitting than those in NS4 solution. When the pit reached a critical size, the increased stress concentration around the pits, resulted in the transition to a crack.

Jan 1, 2005

By M. Dupuis

It has been previously demonstrated [1,2] that using selective collector bar rodding has a big impact on the uniformity of the current density at the top surface of the cathode block and hence on the intensity of the horizontal current in the metal pad, The present study investigates the impact of using selective collector bar rodding on the MHD stability of a 500 kA aluminium electrolysis cell, For this purpose the recently developed MHD package for the aluminium reduction cell time dependent behavior is used.

Jan 1, 2005

By E. Simoncini, S. Ulgiati, M. Raugei

A thorough Life Cycle Assessment of ilmenite extraction and processing to yield synthetic rutile (ERMS/EARS process) was performed according to ISO norms 14040 and updates. The LCA includes the parallel application of selected environmental impact assessment methods (as illustrated in Ulgiati et al. [1]), the results of which are compared and discussed. A MI value of 16 kg of abiotic matter per kg of output rutile is calculated, which is largely determined by the amount of coal that is employed in the reduction and drying steps. The Gross Energy Requirement is 3.33 * 107 MJ/kg, a value which we found to be comparable with that previously calculated by us for alumina. Finally, the increase factor of the Emergy Intensity from the raw mineral to the marketed rutile is 3.19, which points to a comparatively medium-low requirement for indirect environmental support. GWP and AP were calculated to be respectively 1.89 kg(CO2eq)/kg and 12.7 g(SO2eq)/kg.

Jan 1, 2005

By R Lloyd

Coal Services (Health and Safety Trust) funded ARRB Transport Research Ltd to investigate fatigue and performance of truck drivers over consecutive shifts. The main questions were to assess: What is the most important contributor to acute fatigue in mining? Is it length of shift (eg eight hours versus 12 hours) or is it time of day (eg circadian effects)? What is the limit of successive day or night shifts before chronic fatigue affects operator performance in open cut mines? The project methodology included utilising ARRB Fatigue Monitoring Devices (forced-choice stimulus reaction) in eight haul trucks, testing 24 subjects over several weeks. Each subject filled in a Fatigue Risk Questionnaire on lifestyle and health. Operators worked a 14-night, one day off, 13-day roster of 12-hour shifts in a fly-in/fly-out operation with excellent opportunities for restorative sleep between shifts. A total of 3500 hours of real-time data was collected, representing the first set of objective, real-time driver performance data for Australian mining. The data showed that for a single night of driving haul trucks, there appears to be no effect on operator fatigue from the amount of time on task (for the 12 hours). In fact performance was worse through the first eight hours than the last four. The circadian influence had a stronger affect than working more than eight hours. Of the 14 nights worked at the site, nights 13, 14, seven and two respectively, were the worst. This presents a conundrum for policy makers who may like to place caps on working hours or rosters in the hope that it will alleviate the fatigue issue. It will not. The major finding within this study is the combined influence of circadian rhythms (human body clock) and individual variability on performance. The lifestyle habits and the health of individuals have a profound effect on operator performance as shown by the strong positive correlation between high fatigue risk scores from the Fatigue Risk Questionnaire and poor performance. An individualistic approach would appear to have the best chance of reducing high potential incidents due to fatigue through successive nightshifts.

Jan 1, 2005

By D. Want

In titanium-lined autoclave design the most critical point of its mechanical reliability is its titanium batten strips present at the circumferential and longitudinal barrel-weld seams. Recently an Australian Company, W.E. Smith Hudson (WESH) P/L, has developed a fully flush batten strip and is building autoclaves with this design. Significant research and development has been performed in the process. In this presentation, design aspects of these batten strips are presented that cover topics such as residual-stress magnitudes during fabrication, affect of preheat during batten-strip welding and residual stress in respect to fatigue life. There has been little research done regarding the affects of residual batten stress in relation to fatigue life. Considerations of this 'grey' area of design will be discussed based on the author's research data and finite element analysis.

Jan 1, 2005

ICMM’s vision is ‘a viable mining, minerals and metals industry that is widely recognised as essential for modern living and a key contributor to sustainable development’. The ICMM Sustainable Development Framework provides the basis for achieving this vision by assisting the industry to improve its performance. Two years on from the first SDIMI conference, significant progress has been made in further developing and implementing the Framework. To fulfill their commitment to implement and report performance against the ten sustainable development principles in the Framework, ICMM’s corporate members have committed to report ‘in accordance’ with the GRI 2002 Sustainability Reporting Guidelines and the Mining and Metals Sector Supplement, developed by the GRI and ICMM. While much remains to be done, development of the Supplement and the commitment to reporting mark an important milestone for ICMM and the sector.

Jan 1, 2005

By H. Abdollahi

Cold rolling is one of the most important techniques in metal forming since the cold rolling products are almost finished product, The product quality of this process is widely influenced by friction in the roll gap; therefore, controlling the friction and other parameters affecting the cold rolling is very important in order to have a product with high quality, Among the cold rolling parameters, the pressure distribution or friction hill within the roll gap is known as the most significant one, In this study, a new software (Matroll), is introduced which can determine the coefficient of friction (COF) and plot the friction hills for an industrial mill, Besides, based on rolling equations, it offers about 25 rolling parameters as outputs. To verify the software operation, the real industrial rolling data was used as inputs, The results (outputs) are in good agreements with the findings of other researchers, The COF values are very reasonable, The friction hill shows that COF is not constant over the whole arc of contact.

Jan 1, 2005

By B Mohanty, G Yamin

A number of parameters, aside from blast design and pre-existing rock conditions, can change the performance of the explosives system in actual blasting practice. Sympathetic pressures caused by detonation of preceding holes have been identified as a major contributor to explosive system malfunctions, leading to uneven blasting performance. These effects can occur both within a hole or across several holes. These can consist of high transient pressures related to the shock phase of the explosion or the relatively longer or quasi-static pressures associated with the explosion gas expansion phase. This study presents the findings from an on- going investigation on measurement and analysis of these pressures between donor and receptor holes in a granitic outcrop for representative inter-hole distances and borehole conditions, employing single cartridges of emulsion explosive in 45 mm diameter holes. The results, despite wide scatter in the measured values, show the very short duration pressures to range up to 7 MPa and arriving within a few milliseconds after detonation, whereas the much lower amplitude pressures arrive after tens of milliseconds. Both have the potential to seriously affect the performance of an explosives system.

Jan 1, 2005

By Randy Sandrik

Sampling has evolved at two large underground limestone mines as conditions and product requirements have grown tougher over 100 years of mine life, requiring innovative techniques to insure delivery of high purity limestone. Sampling insures delivery of consistent product to customers at the lowest possible cost. Statistical considerations have evolved from simple data collection to predictive and process capability analysis. Sample methods include borehole samples, face (using a proprietary face-sampling device), and total plant feed automatic, process, and final product sampling. Lessons learned, while keeping costs at historically low numbers, include the importance of geological models, exploration drilling density, face sampling, and blending of ore.

Jan 1, 2005

Breaks in coal slurry impoundments can threaten the lives and health of area residents, destroy homes and businesses and contaminate water supplies. This dangerous potential looms over coalmining regions in West Virginia and throughout Appalachia. The Coal Impoundment Project was begun in June 2003 to provide an inventory and mapping of active and abandoned impoundments in West Virginia. The project also provides the public with specific information about the impoundments in their communities. It is dedicated to alerting residents of danger and evacuation plans, reducing risk to residents and finding alternatives to impoundments. Since its first year, more than 100 impoundment sites have been added to the project’s Website.

Jan 1, 2005