Search Documents

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

By S. Felderhof, W. S. Vaughan

"Over the years, it has been increasingly difficult for the minerals industry to raise the necessary capital for its activities. To alleviate this phenomenon, complete transparency and capital market efficiency is needed. Since a company’s mineral resources and mineral reserves base is an essential component to obtaining capital, reporting these assets must also be transparent and efficient. This must occur, however, at an international level given that mineral industry operations, and its financing, are international. To achieve this, an international committee (i.e. Australia, Canada, South Africa, the United Kingdom and Europe, and the United States) was formed and has been developing standards for the reporting of mineral resources and mineral reserves.The effectiveness of these standards, however, depends on adoption by the required regulators. Unfortunately, these standards have not been recognized by the U.S. Securities and Exchange Commission (SEC). Instead, the SEC adheres to its old standard (Industry Guide 7), making it increasingly expensive and difficult for international mining companies to obtain capital in the United States. Compounding the problem is the SEC’s influence over the current work of the International Accounting Standards Board and the International Organization Organization of Securities Commissions. These organizations are in the process of standardizing international accounting practices and international securities rules and regulations. Their current position may prevent adoption of the industry-developed mineral resources and mineral reserves standards which are internationally recognized."

Jan 1, 2005

By G De Tomi, R Sousa, A Lapworth

One of the current challenges for iron ore producers is the ability to respond to changes in ROM stockpile specifications in a quick and cost-efficient manner. The decision-making process to respond to such changes is normally associated with grade-control and short-term mine planning activities, from where new operating instructions to the mine are provided. Mines are under increasing pressure from changes in the industry, such as a scarcity of skilled staff; a higher turnover of skilled employees and tighter product specifications. The quality of operational activities easily suffers as a result of these pressures. The technology that supports operational activities is often poorly implemented, which results in systems being unsustainable and poorly understood by the organisation. All successful technology implementations rely on the people, processes and technologies involved being well understood. Because of the complex nature of mining, the processes that underpin mine planning, scheduling and operational control are often not well defined. This results in activities undertaken by individual departments being poorly integrated. Datamine has developed a set of tools and methods for decomposing; capturing and documenting processes and ensuring those are embodied in implemented solutions. A case study of such a solution is the GEROS planning system, which has been successfully implemented at CVRDÆs Southern Iron Ore System, in Minas Gerais, Brazil.

Jan 1, 2005

By S W. Robertson, A Vercuil, P Craven

Mintek is currently developing a design approach for the heap leaching of low-grade primary copper sulphide material. Since the leaching of chalcopyrite requires elevated temperatures, the generation and management of heat within the heap is crucial. Furthermore, the precipitation of iron needs to be managed to prevent premature blinding of the heap, and acid consumption needs to be limited to contain cost and limit the dissolution of gangue impurities. Standard column tests using jacketed 1-m and/or 6-m columns do not allow accurate prediction of temperature changes and heat generation in an actual heap. Mintek therefore utilizes a computer model to calculate the energy balance and heat generation with time, based on the measured sulphide oxidation rates in the column. The temperature in the column is then adjusted to reflect the computer-predicted temperature in an actual heap. Using this approach, an overall copper extraction of 70% was achieved in 120 days, using 1-metre columns, when treating an ore blend containing 1.36% chalcopyrite, 0.23% chalcocite, 0.07% covellite, 3.8% pyrite and silicate gangue (92%). The chalcopyrite contribution to the total copper content in the feed was 75%. This was followed by 6-m columns using a similar approach, and the column results will be validated on a 23,000 tonne test heap. Key Words: heap; bioleach; chalcopyrite

Jan 1, 2005

By B. Arsenault

Aluminum coatings can provide galvanic cathodic protection for several metals and alloys, In order to be a suitable protective solution on structural components, the mechanical integrity of the component must be preserved, In particular, fatigue properties are a challenge for thermal-spray protective coatings on mechanical structures, To address the issue of the fatigue integrity of 7075 aluminum alloy with an arc-sprayed protective coating, different surface preparations prior to arc spraying were considered, In the present work, a feasibility study was performed using laser ablation as a surface-preparation technique before or during arc spraying of coatings, This was collaborative effort between the LERMPS laboratory in France, the National Research Council Canada and the Royal Military College of Canada, Both fatigue and adhesive properties of aluminum coatings were evaluated in relation to substrate-surface-preparation techniques including laser ablation (Protal® process), grit blasting and shot peening. Results indicate that a combination of key conditions, including the use of nitrogen as the arc spray gas, shot peening, and proper laser energy density for ablation, provide high fatigue resistance of metallic coated 7075 alloy substrates. Specimens prepared under these conditions show a similar fatigue resistance to uncoated substrates.

Jan 1, 2005

By A. M. Milev

A stand-alone instrument especially designed for recording strong ground motions was used in this study to create a large data base of peak particle velocities measured on stope hangingwalls. A total number of 58 sites located in stopes mining the Carbon Leader Reef, Ventersdorp Contact Reef, Vaal Reef and Basal Reef were monitored. The peak particle velocities were measured at the surface of the excavations to identify the effect of the free surface and the fractures surrounding the underground mining. From the monitoring results obtained, the velocity criterion of 3 m/s will bean adequate value that support systems have to sustain during a rockburst in most cases. However, PPVs in excess of this criterion were recorded, and some PVDs were damaged or irretrieveable, a consequence of which was that possible extreme events were not recorded. The data recorded on the skin of the excavations were compared to the data recorded by the mine seismic networks to determine the site response, defined as the ratio of the measured peak ground velocity to the peak ground velocity inferred from the mine seismic data. The site response measured at all mines studied was found to be 9 ±3 times on average. Values of the site response did not vary significantly with seismological parameters such as peak ground velocity, hypocentral distance and source radius.

Jan 1, 2005

By D Sidea

There has been increased focus in Australia on large diameter raise boring for ventilation shafts and orepass excavation in good quality, brittle, highly stressed rock. As mining in many parts of Australia progresses to deeper levels, more vertical openings are being excavated in highly stressed ground conditions. However, whilst shafts have been successfully raise bored in highly stressed rock, it is often at a significantly increased risk of loss or damage to inhole equipment. It is important for both mine owners and contractors to have an appreciation of these risks at the planning and tendering phases of raise boring contracts. This paper provides an understanding of the risks associated with large diameter raise boring and a review of methods to predict failure in highly stressed rock.

Jan 1, 2005

Lime production is the largest single chemical use for limestone and dolomite. The term “lime” in this review refers to high-calcium and dolomitic quicklime, their hydroxide forms and dead-burned dolomite. This review is restricted to a discussion of the U.S. lime industry. Production and consumption In 2004, according to preliminary data, U.S. lime production was about 20.1 Mt (22.1 million st), an increase of 900 kt (990,000 st) compared with 2003. Production in2004 was valued at about $1.4 billion. Commercial sales of lime totaled 18.6 Mt (20.5 million st) and captive production was 1.5 Mt (1.65 million st). Total U.S. consumption was about 20.2 Mt (22.2 million st). The majority of U.S. lime trade was with Canada.

Jan 1, 2005

By R O. James

The usual focus of papers on fatty acid collector action in non-sulfide flotation is on the adsorption of the carboxylate and/or neutral molecule species at the mineral-solution interface. Little attention is paid as to whether or not the solution conditions correspond to true solutions, micellar and other self-assembly objects or precipitates. Our examination of the solution chemistry of the important fatty acid collector, oleic acid, has revealed that many, if not most investigators set their experimental conditions to be in micellar or precipitate domains while arguing, often by implication, that they have only solute species present. We have investigated the equilibrium solution domains usually encountered in studies of oleic acid flotation of such minerals as barite, calcite and fluorite. The alkaline earth-fatty acid and liquid oleic acid precipitate phases exert a strong influence on the solution chemistry, a fact not often appreciated in many studies.

Jan 1, 2005

By L D. Redden, M G. Nelson

Mechanical flotation machine design is typically based on hydrodynamic analysis, with scale-up calculated by geometric proportionality. End users often specify and purchase machines on the basis of retention time, characterised by the æ$/m3Æ approach; they may also consider the manufacturerÆs installed base. In some applications, end users also consider specific energy and the impact of energy consumption on operational costs. In other cases, a decision may be based on machine type (forced-air versus self-aspirating) and perceived metallurgical or operational advantages of one machine type over the other. With regard to metallurgical performance efficient bubble-particle contact is very important and is primarily influenced by two factors:the concentration and size distribution of bubbles in the machineÆs contact zone (the volume enclosed by the disperser); and the number of times that slurry is pumped through the contact zone. The second factor is a function of the machineÆs pumping rate and its retention time. Field data show that pumping efficiency is independent of aeration rate. In this paper, a new dimensionless number for the characterisation of flotation efficiency is presented. The contact frequency number (CFN) is defined as the number of times a given volume of slurry passes through a machineÆs active contact region, and is given by: CFN Qp/Qf, where:Qpis the pumping rate through the contact regionQfis the volumetric feed rate to the machine

Jan 1, 2005

By A. Iordanidis

Fly ash samples were collected from two large lignite-fired power plants of Ptolemais region, northern Greece. Environmental Scanning Electron Microscopy (ESEM) was applied for the characterisation of the samples. ESEM coupled with Energy Dispersive System (EDS) provided fast and accurate results on the morphology, mineralogy and chemical composition of the fly ash particles. Fly ash consists mainly of aluminosilicate glass, silicates, oxides-hydroxides, sulphates, carbonates and char. Various types of chars, spheres (e.g. ferrospheres, cenosphers, plerospheres etc.), spheroids, agglomerates and mineral crystalls were observed. The size distribution of the fly ash particles was correlated with their mineralogical and chemical composition. Possible environmental impacts and potential utilization is also discussed in this study.

Jan 1, 2005

By Harry Verakis

Electronic detonator systems are an advance in technology beyond conventional electric detonators for initiating explosives and blasting agents. Their use is widening into the mining operations of the U.S.A. Each electronic detonator system differs in design, construction, operation, and testing features and each system is different than “conventional” electric detonators. There are benefits of electronic detonator systems which serve to improve blasting safety. With the introduction of electronic detonator systems for mine blasting, issues were raised about the application of MSHA regulations for shunting and circuit testing. The MSHA regulations for surface and underground mine blasting operations address the use of “electric” detonators. Although electronic detonators are initiated by an electric pulse or current, their design is unlike “electric” detonators. To resolve the issues of shunting and circuit testing with respect to MSHA regulations, a technical and field evaluation of electronic detonators was made and the results are presented.

Jan 1, 2005

By V. I. Birss

Planar solid oxide fuel cells (SOFCs) offer great promise as stationary power generation devices, primarily due to their flexibility in terms of fuels, high energy conversion efficiency (when both electricity and heat are captured), and their relatively low fabrication costs. However, the anode performance can be compromised by such factors as exposure to certain sulfur-containing fuels and the deposition of coke when using hydrocarbon fuels. In terms of the cathode, its performance is limited primarily by the slow kinetics of the oxygen reduction reaction, while its lifetime can be negatively affected by factors related to the corrosion of currently used stainless steel interconnect materials. This talk will present an overview of these challenges and some possible solutions to these problems. The presentation will also focus on how electrochemical methods can be used to evaluate and improve the performance of SOFC anodes, cathodes, and interconnect materials. In addition, recent promising research efforts directed towards performance enhancement of SOFCs through the use of nanoscale electrocatalysts will be discussed.

Jan 1, 2005

By John B. Ackerman, John G. Mansanti

INTRODUCTION Placer Dome's Turquoise Ridge Joint Venture operation is located some 75 km northeast of Winnemucca, a community in north central Nevada. Formerly known as the Getchell Gold Corporation and First Miss Gold, the operation mines refractory ore from the Getchell and Turquoise Ridge gold deposits located on the east flank of the Osgood Mountain Range above the Kelly Creek Basin in the Potosi Mining District. Mining has been ongoing at Getchell since shortly after its discovery in 1934, and was the nation's second leading producer of gold after Homestake in the early 1940s. Over its history the Getchell property has been mined for gold, tungsten, molybdenum and arsenic; mining methods varied from open pit mining to underground mining; processing options included conventional milling, flotation, roasting, heap leaching, and most recently pressure oxidation followed by CIL (carbon-in-leach). As an historical note, the US Bureau of Mines developed the use of carbon for gold recovery at Getchell during the 1940s (Horton 1999). Placer Dome acquired the property in May 1999. The pressure oxidation plant was mothballed in July 1999 and the property was placed on care and maintenance in February 2002 pending further exploration results. The property is currently ramping up to full production status. A joint venture agreement (75% Placer Dome, 25% Newmont) was established with Newmont Mining in 2003 and ore is processed at their nearby Twin Creeks autoclave plant. Mine dewatering is a key element to success. Arsenic is a ubiquitous mineral in many of the mineralized areas of northern Nevada, necessitating treatment of water prior to re-infiltration.

Jan 1, 2005

By A. H. Swart

Rock engineering is concerned with the design of rock structures generated by mining activities. Therefore, rock engineering designs have major implications for the safe recovery of mineral deposits and operating costs. The paper deals with a few challenges facing rock mechanics engineers operating in the hard rock underground mining environment in South Africa. Finally, examples are included, which may assist rock mechanics engineers in providing better designs, which could ultimately lead to further improvement in safety and lower operating costs.

Jan 1, 2005

By T Weldon

In the last 15 years, it has become increasingly popular to win gold and silver from carbon strip solutions with electrolytic æsludgeÆ cells. The precious metal sludges produced in the cells are washed to the cell bottom and pumped into filters. Most new operations are specifying sludging cells, and many older operations are being retrofitted with up-to-date electrolytic sludge cells and filters. The new sludging cells are generally more energy efficient than older cells, but more importantly, the cell operations to remove product are much less labour intensive, cleaner, and the operator need not have physical contact with the electrolytically produced metal. A case study of a major North American gold producer (50 000 kg/yr) that removed old style stainless steel wool cathode cells and installed new sludging cells and sludge filters is presented. The effect of various impurities is discussed.

Jan 1, 2005

By T C. Westerfield, G, M J. Mankosa

An innovative separator known as the HydroFloat cell has been developed specifically for the upgrading of coarse particles that are difficult to recover using conventional flotation cells. The novel characteristic of this separator is the formation of a hindered teeter-bed of fluidised solids into which small air bubbles are injected. The air bubbles selectively attach to hydrophobic particles and form particle/bubble agglomerates that segregate atop the teeter-bed due to their lower apparent specific gravity. The low-density agglomerates are eventually carried into the product overflow launder by the rising current of teeter water. Hydrophilic particles remain in the teeter-bed and are discharged to underflow as a high solids content tailing. Benefits of this hybrid flotation-density separator include enhanced bubble-particle contacting, increased particle residence time, and very low air demand. Test data indicate that significant improvements in the recovery of coarse particles can be achieved using this innovative technology. This article describes the theoretical basis for the development of the HydroFloat cell and provides an overview of recent pilot-scale tests conducted for the phosphate industry.

Jan 1, 2005

By C F. Prins, C LantuTjoul

Mineralisation in alluvial diamond or vein gold deposits is often hosted in trapping mechanisms. For instance, diamonds are nested in bedrock depressions such as gullies and potholes which were carved out by the sea long before the diamond deposition took place. Similarly, gold mineralisation can precipitate in the necks of a boudinage structure. In such deposits, the spatial distribution of the mineralisation is governed by the mutual arrangement of the trapsites and by the grade variations within each trapsite. Reliable estimates can be obtained only if they rest on a proper knowledge of both degrees of variability. This creates a challenging sampling problem, as during the exploration phase it is important to have a good global mean estimate to enable decision making towards the future. A similar problem occurs for local estimates at a later stage of development. To understand and manage the sampling for global means, specific sampling procedures are required based on an appropriate choice of sample support size and spacing. Estimates from such sampling campaigns should be unbiased, and the less variability they display, the better the sampling parameters. The performance and impact of sampling parameters are tested and compared on different simulated deposits.

Jan 1, 2005

By Rimas Pakalnis, Lyndon Clark, Tom Brady

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate data on weak rock masses into existing design relationships, with an emphasis on updating the span design curve for manned entries and the overbreak curve for longhole entries. Both curves were originally developed at the University of British Columbia, Vancouver, BC. The original database has been augmented by information from mines throughout the United States, Canada, Australia, and Europe. The common factor in all these mines is the presence of a weak back and/or walls. In most cases, the ore zone is the weakest rock unit and must be stabilized so that the mineral-bearing rock can be extracted safety. The current NIOSH research attempts to provide rock mechanics tools to assist a mine operator in making economic decisions that will also ensure a safe working environment. This paper documents the Nevada database with a special emphasis on Nevada underground gold mines.

Jan 1, 2005