Search Documents

By J J. Plumb, P D. Franzmann

A study was conducted to describe the microbiology of the MICCL Monywa chalcocite heap bioleaching operation. Microorganisms were detected in the heap using culture-based techniques and cultureindependent PCR-DGGE analysis of the 16S rRNA gene. The metabolic requirements, temperature and pH optima were determined for selected strains isolated from the heap material. Six strains (BH1-BH6) were enriched and isolated from heap solids and leachate samples. Phylogenetic analysis of the 16S rRNA genes showed that strains BH3 and BH4 were closely related to the acidophilic bacterium Acidithiobacillus caldus and strains BH5 and BH6 were closely related to Leptospirillum ferriphilum. The optimum growth temperature for L. ferriphilum was 41.3¦C and the optimum pH range was 1.1 to 1.5. A new species of Archaea was isolated from the heap samples. Cells of the proposed species, Ferroplasma cyprexacervatum (æcyprusÆ L.n. meaning copper; æexacervoÆ L.v. meaning æto heap upÆ), are non-motile pleomorphic cocci, capable of chemomixotrophic growth with ferrous sulfate and yeast extract. Cells grow anaerobically on ferric iron in the presence of potassium tetrathionate and yeast extract as electron donors. Growth occurs from 14¦C to 63¦C, with an optimum temperature of 55.2¦C. The optimal pH for growth was 1.0 - 1.2. The species was phylogenetically most closely related to Ferroplasma acidiphilum with a 16S rRNA gene sequence similarity of 95 per cent. Molecular analysis of mine samples (16S rRNA PCR-DGGE) detected the above-mentioned cultured strains of microorganisms as well as species of Sulfobacillus and other unknown Proteobacteria. The microbial community of the Myanmar bioleach heaps contained similar levels of diversity to a dump bioleach operation in Chile, but contained greater amounts of biomass than another heap bioleach operation in Australia. The operating parameters of the Myanmar heaps (low pH and moderate temperature) have selected for the growth of moderately thermophilic microorganisms that are more commonly found in extremely low pH acidic mine drainage sites than in heap systems. The novel species of Ferroplasma is thought to be involved in the aerobic and anaerobic cycling of iron within the heap bioleaching environment.

Jan 1, 2004

By Jin-Hwa Song

Rolling temperatures and cross rolling ratios were varied to investigate the effect of crystallographic texture of alpha-phase on the anisotropy of mechanical properties in modified Ti-6A1-4V alloy. Hot rolling method was unidirectional and cross rolling, during which the rolling temperature was in the range of 830°C and 920°C. Cross rolling ratios were varied from 0.3 to 1.0 at 875°C. For unidirectional rolling, as the rolling temperature increased texture changed from the mixed basal and transverse texture to the simple transverse texture. Contrary to other work, it was observed that the maximum intensity of transverse components increased with the increase in rolling temperature. For cross rolling, on the other hand, the transverse texture component was almost suppressed at 830°C, giving rise to a symmetrical basal texture. With increasing cross rolling temperature, the transverse texture components developed again. A simple transverse texture, which showed two maxima appearing circularly 90° apart, was observed at 920°C. It was found that unidirectional rolling could not eliminate the transverse texture, which resulted in the anisotropy of mechanical properties. The anisotropy of mechanical properties obtained from tensile and V-notch Charpy test was closely related to the crystallographic texture and its intensity at each rolling condition. To obtain the isotropy of mechanical properties by cross rolling, it is suggested that cross-rolling ratios should be controlled above 0.5. The variation of rolling temperatures and directions has great influence on the anisotropy of impact value rather than tensile strength.

Jan 1, 2004

By J. Kemeny, B. Norton, T. W. BoBo

Digital image analysis systems to quantify particle size of crushed materials have successfully been applied in large-scale mining operations throughout the world. Particle size measurement at various crushing and sieving stages, especially in aggregate production, will facilitate the industry’s desire and need to achieve higher levels of process control and automation. This paper will 1) summarize applications of digital image analysis in the industrial minerals industries and introduce the Split-Online technology; 2) detail an actual recent test application of digital image analysis that ultimately lead to the installation of an automatic, non-invasive particle size distribution monitoring system; 3) document how this information is being applied: and 4) summarize the new Split-Online Aggregates Module now available.

Jan 1, 2004

In the traditional analysis of airblast and ground vibration, it is often assumed that only that single blasthole possessing the maximum charge weight (or a small group of blastholes initiating in an 8 ms time window) will determine the peak level of airblast or vibration. This assumption is examined in light of waveform superposition, and is found to be unsound. More rational alternatives are given in which all blastholes (or a selected number of blastholes) are assumed to contribute, in varying degrees, to the peak vibration or airblast. However, it is also shown that there is generally no precise solution for determining the number of blastholes that contribute to the peak level. The technique of waveform superposition does not rely on evaluating which group of holes produced the peak, and so is the preferred method for prediction. Some numerical and analytical models of wave superposition for airblast and vibration are also reviewed and recent approaches discussed. The directionality of airblast, in particular, is analysed in detail using a new superposition model that is constructed of two submodels, onenumerical, the other analytical. This model shows that the airblast from even a single blasthole can be highly directional. The detail of this model is commercially sensitive and will not be discussed. Only results and a broad discussion will be given.

Jan 1, 2004

By N. Ntakaburimvo, C. Allaire

This paper presents an innovative experimental set-up which simulates refractory degradation by separate and simultaneous action of abrasion, erosion and partially or totally immersion corrosion whether dynamic or static. It also presents abrasion testing results obtained from five commercial aluminosilicate refractories used in aluminium melting and holding furnaces. Abrasion wear was quantified by measuring the weight loss and the depth of wear, as well as by determining materials properties degradation, such as the residual rupture force and the residual modulus of rupture. Results were correlated to as- fired materials properties, such as rupture force, flexural strength, elastic modulus, toughness, and apparent porosity; in order to establish which property could be used for refractory abrasion wear prediction. They were also related to the critical length of pre-existing defects and to those generated by the abrasion process. Positive correlation was established between abrasion resistance and mechanical properties, particularly for refractory castables. For similar mechanical strength, the castables tested offered less abrasion resistance than the brick sample.

Jan 1, 2004

This short paper outlines the authorÆs views regarding the progress we have made as an industry in managing mining assets over the past 500 years. It represents a personal view û but one founded in fact-based observations of mining companies and of the mining industry in general. There is no doubt that AgricolaÆs views as expressed in De Re Metallica (1556) were visionary. There is also little doubt regarding another issue û that whilst a great deal has been learnt about the management of mines since AgricolaÆs time, observations suggest that best practice management is the exception rather than the rule across our industry. Although insights regarding the successful management of mines have become apparent, we still witness unnecessary errors in our industry that lead to the loss of shareholdersÆ funds. By highlighting some aspects of current best practice, particularly in the arena of operations management, it is hoped that this short paper contributes a small step along the next 500-year-long learning curve. The paper concludes with a brief description of the progress and impact of continuous improvement initiatives at Kalgoorlie Consolidated Gold Mines (KCGM). Located in the Kalgoorlie Goldfields, KCGM is currently AustraliaÆs largest gold mine producing over 800 000 ounces of gold per annum. Improvement initiatives at KCGM look set to deliver some $100 million in value over life-of-mine.

Jan 1, 2004

By V. Scovazzo

Cost-effective underground mine configurations have been designed in highly fractured rock masses where the stone possesses a high material strength. A limestone mine in the eastern United States is used to demonstrate procedures for the geotechnical design of one such operation. The mine discussed is located in both limbs and the axis of a recumbent fold that fractured the rock mass. In a highly fractured rock mass, where the host rock has high strength, a design can be developed to alleviate intact rock failure. This is possible because in most cases as the stress levels needed for intact failures are approached, the stresses are quickly dissipated due to movement along discontinuities, which represent planes of weakness. As a result most underground failures in highly fractured rock are due to sliding or toppling. Even when intact rock fails in a highly fractured rock mass, it is the movement along an existing joint or other weakness plane that often initiates or causes this failure. It is therefore important to obtain the characteristics of weakness planes that are the discontinuities within the mass. The required information on weakness planes, geology, and strength of materials is discussed and recommendations for obtaining this information are presented. A discussion is provided on failure modes and the use of developed information for their evaluation. The impact on geotechnical design is demonstrated through pillar sizing procedures; however, this approach can also be applied to mine roof and pillar foundations.

Jan 1, 2004

By J. F. Archibald

A research effort has been undertaken, under Workplace Safety and Insurance Board of Ontario (WSIB) sponsorship, to characterize the support capabilities of conventional and innovative spray-on lining materials for mitigating dynamic failure effects created by simulated rockbursts. Conventional spray support media, such as shotcrete and fibrecrete linings, and a variety of new spray-on lining materials [thin, spray-on liners (TSLs)], typically polymer-type thin coatings, were subjected to simulated rockburst influence. For baseline comparison, conventional rockbolt and bolt-and-mesh support products were also evaluated. Observation of lining performance was undertaken through completion of field-scale support and rock detonation trials. Controlled blasting tests were conducted at the Queen’s University Explosives Laboratory to examine the effectiveness of the variety of surface coating agents for modifying dynamic rock spalling processes. All tests were performed upon largely undisturbed and homogeneous rock materials in highly repeatable fashion. All blasts were observed seismically and photographically to provide detailed information concerning rock motion, surface fracturing, ejected fragment motion and support liner survivability characteristics. These material comparison trials were performed to assess the relative effectiveness of a wide range of currently available area support techniques for suppressing hazards associated with dynamic rock ejection. The results of this study validate that thin, spray-on linings may be equally as effective, and often better, than conventional support materials at mitigating rockburst or like damage in highly stressed mine environments.

Jan 1, 2004

By N. N. Malila, N. R. Shoko

The ever-increasing pressure on the profit margins of ferro-chrome producers and the gradual depletion of deposits of rich hard lumpy chrome ores calls for the ferrochrome industry to maximise the use of fine fractions of concentrates and friable chromite ores. Zimbabwe is endowed with huge deposits of refractory and friable ores that occur on and off the Great Dyke complex. The conventional metallurgical process of smelting of chromite ores in submerged arc furnaces is favoured by the use of refractory hard lumpy ores. The requirement to use all lumpy ore has been circumvented to a large extent at Zimbabwe Alloys. The use of briquetted chrome ore fines in the production of Ferrosilicon Chrome and High Carbon Ferrochrome has yielded positive results over a period in excess of twenty-five years. Of the three industrially used methods of agglomeration of chromite ores; sintering, pelletisation and briquetting, briquetting is preferred because the other two are associated with higher capital and operational cost. Zimbabwe Alloys has developed operational and technical expertise on the briquetting and utilisation of chromite ore fines and concentrates. Variations in the quality of available chromite ore fines imply that their amenability to briquetting is a dynamic problem. Appropriate briquetting parameters to guarantee quality briquettes are essential to the successful use of briquetted chromite ore fines. In developing a technology for briquetting of chromite ores, it is important not only to study the mineralogical and grain-size characteristics of the chromite ore fines but also to make an informed choice of the type and quantity of the binder and the conditions for producing a physically and chemically competent green and cured briquette. This paper discusses Zimbabwe Alloys' experience on the briquetting process and the advantages derived in the smelting of the briquetted chromite ore fines in comparison to the use of conventional lumpy chromite ore with respect to improvements in chromium recovery and as a consequence related efficiencies and unit cost of production.

Jan 1, 2004

By Ashok D. Dalvi

Production of nickel from laterite ores has occurred for over 100 years beginning with processing of garnieritic ores from New Caledonia. However, until now the world nickel supply has been predominantly from sulfide sources. Going forward, the authors project that the production of nickel from sulfide ores will remain more or less constant. Most of the expansion in nickel production capacity over the next ten years will come from processing of laterite ores. Thus the capital and operating costs of new laterite projects will have significant impact on the nickel supply and therefore price. The authors have reviewed the history and capital and operating costs of various recent laterite projects and capital and operating costs of these projects and those "on the drawing board". The authors have also evaluated the risk associated with such projects. The paper will discuss the impact of this and the recent history on the future development of laterite nickel projects.

Jan 1, 2004

By Y. Kocaefe, S. Afshar, D. Kocaefe, Z. Kunt, C. Allaire

Interaction of aluminum with silica based ceramics Jose M. Soto, Jeffrey D. Smith, William G. Fahrenholtz. Department of Ceramic Engineering University of Missouri-Rolla Rolla, MO 65409-0330 USA ABSTRACT Interactions between A356 aluminum (Al-Si alloy) and dense fused silica (FS) riser tubes used for low-pressure casting of aluminum alloys were evaluated using a sessile drop approach. The tubes have a short service life, but cost and thermal shock resistance make them an effective solution. The main problem encountered during use is the reaction of aluminum with silica to form alumina and silicon, which causes failure. Tests have been conducted on as-fired (uncoated) and modified (coated) tubes. Experiments were carried out in a horizontal furnace at 1225°C under argon to minimize the effect of the aluminum oxide on the interactions at the alloy-silica interface. Images of the drop were acquired and contact angle values were estimated for uncoated and coated samples, but no significant differences in the contact angles were observed. Scanning electron microscopy revealed the presence of cracks at the interface between the reaction zone and the unreacted silica. The presence of reaction products (silicon in the reacting alloy and aluminum in a reaction zone between the alloy and the unaffected silica) has been confirmed using energy dispersive spectroscopy. A two layer coating system was found to be effective in reducing penetration of the aluminum alloy. The interactions between bed media and aluminum have been studied under static and dynamic flow conditions. An experimental system was set up simulating a small filter. Desired flow field can be created around alumina particles and velocities can be adjusted. A mathematical model was developed to predict the velocities, and this was validated using data from a visualization study. The interaction zone on the surface of the particles was analyzed with optical microscopy and SEM. This paper presents the study and compares the results under static and dynamic flow conditions.

Jan 1, 2004

By R. T. Jones

Slags have been produced as by-products from pyrometallurgical processes for thousands of years, and have generally been regarded as waste. Many of these slags are no longer seen as residues merely to be discarded, but as potential economic sources of metals, or as useful by-products in their own right. Slag cleaning can enhance the recovery of valuable metals in existing pyrometallurgical processes, or can produce economic value from recycling old slag dumps. For example, a process has been developed and implemented industrially for recovering cobalt from copper smelting slag in a DC arc furnace. The relatively non-leachable behaviour of glassy slags allows them to be used as a very safe means of disposal of metallurgical waste streams, including many that are classified as hazardous. The high temperatures, reducing conditions, and good mixing that can be achieved in a DC arc furnace enable the effective functioning of this environmentally beneficial means of disposal. Lead blast furnace slag can be rendered safe for disposal by treating it using the Enviroplas process, which strips most of the hazardous lead from the slag (and traps the rest in an insoluble glassy slag) and recovers economic quantities of zinc by absorbing (in a lead splash condenser)the zinc vapour that is fumed off in the furnace. Another example can be seen in the recovery of a chromium- and nickel-containing alloy from stainless steel plant dust, while producing a disposable residual slag. The examples presented here illustrate that it is possible to develop processes that are both economic and environmentally beneficial. Keywords: DC arc furnace, plasma, slag cleaning, cobalt recovery, zinc fuming, Enviroplas, jigging, re-melting fines, environmental, economic

Jan 1, 2004

By S. J. Knoll, D. F. Scott, T. J. Williams

Highly stressed rock in stopes continues to be a primary safety risk for miners in underground mines because it can result in failures of ground that lead to both injuries and death. Spokane Research Laboratory personnel investigated electromagnetic (EM) emissions in a deep under-ground mine in an effort to determine if these emissions could be used as indicators of impending catastrophic ground failure. Results suggest that (1) there is no increase in the number of EM emissions prior to recorded seismic activity, (2) some EM signals are generated during blasting, (3) interference from mine electrical sources mask seismic-generated EM signals, (4) EM emissions do not give enough warning (compared to seismic monitoring) to permit miners to leave a stope, (5) the distance an EM signal can travel in the rock is between 17.7 and 39.6 m (58 and 130 ft), and (6) current data acquisition systems do not differentiate between EM signals generated from seismic activity and random mine electrical noise. These results preclude monitoring EM emissions as precursors of impending catastrophic ground failure.

Jan 1, 2004

By Craig Byington

The stress-field orientation mapping and analysis (SOMA) technique for determining the operative stress field near mine workings and its relationship to various fracture sets is described using Dickenson-Russell Coal Company's Laurel Mountain mine as an example. Carried to its practical application, this technique ultimately defines the optimal orientation for the mine workings wherein pillars, rather than rock bolts or other roof support methods, dominantly shoulder support of the highest-probability, potential, roof-fall blocks. It also provides a predictive tool describing local variability in rock deformation and in secondary roof support methods. Fracture discontinuities within a rock mass, either as pre¬existing natural fractures or as mining-induced fractures, are uniquely necessary for every brittle-deformation ground failure including roof falls. Prediction and mitigation of roof falls requires quantifying the interaction between the fracture sets and the operative principal-compressive¬ stress-axis orientation (olo). The SOMA technique utilizes the interaction between fractures and 61o, specifically their dilation or closure, to calculate the orientation of 610, and to estimate the orientations of 62o and o3o. A stereonet program is used to organize and statistically analyze the fracture data, and then to determine the optimal orientation for the mine workings. The final step in the SOMA technique involves modeling the Laurel Mountain mine using a 2-D, finite-element, modeling program. This assures that the interpretations regarding the optimal working orientation closely match the deformation features observed in the mine. It also provides a predictive tool describing highly variable stress and strain partitioning, seemingly erratic rock-bolt failures and the interactions between different sets of mine workings within different coal seams. The critical importance of including the fracture sets is well illustrated in the Laurel Mountain mine where the effects of earlier mining of an underlying seam is contrasted in both a fractured and otherwise identical non-fractured model to illustrate the consequences of ignoring fractures in a predictive roof-fall model.

Jan 1, 2004

By B A. Wake, G G. Lowder, M J. White

The Tooloom gold field is located within the New England Fold Belt in the far northeast of New South Wales, approximately 130 km south southwest of Brisbane. Gold was first discovered at Tooloom in 1857. Within a few years up to 10 000 people were mining placer gold deposits in the Tooloom valley and a few tried their hand at mining hard rock occurrences as well. Mining of alluvial gold continued in a small way at Tooloom until very recently, but only in the last few years, since Malachite Resources acquired its interest at Tooloom (now 100 per cent), has the full potential of this large, reduced intrusion-related gold field been appreciated. By the mid 1870s, once the alluvials were largely worked out, most of the early miners had made the 270 km trek north to the newly discovered Gympie gold field and Tooloom slipped into obscurity. Such was this obscurity that the Tooloom gold field was not recorded on published Government geological maps until 2001, four years after Malachite became involved. The many hard rock prospects that Malachite has identified in recent years were largely or completely unknown. Tooloom is a good example of blinkered thinking when it comes to modern mineral exploration. The New England province in NSW has long been the æpoor relationÆ to the much better known and more highly favoured Lachlan Fold Belt in NSW. It has also suffered serious neglect compared with the Queensland part of the New England Fold Belt that hosts such major gold deposits as Mt Morgan (>7 Moz), Gympie (>3 Moz) and Cracow (>1 Moz). Tooloom is proof that prospective geology does not stop at state borders.

Jan 1, 2004

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004

By V. Prabhu, D. Mantha, R. Reddy

Secondary copper blast furnace slag was treated with carbon to derive the conditions for maximum recovery of copper with a minimum simultaneous reduction of iron oxide. Experiments were carried out to study the effect of temperature, carbon and CaO additions to the slag on the efficient recovery of copper. A two-stage reduction process was also employed to study the efficiency of copper recovery and the results were compared with those of single-stage reduction. The maximum recovery of copper in alloy phase was obtained with 5 % initial carbon in the slag, 2% CaO addition to the slag and at a reducing temperature of 1573 K. Higher grade of the alloy phase with respect to copper was obtained by employing a two-stage reduction process. The results obtained in this study are comparable to those of the earlier research on the recovery of copper from reverberatory furnace discard slags.

Jan 1, 2004

By N Ozawa, R Kaneko, M Arimit

The Mitsubishi Higashitani limestone mine is a ten million tonne per annum operation located near the city of Kitakyushu on JapanÆs western island of Kyushu. Higashitani is one of the largest limestone mines in Japan and accounts for about five per cent of national production. Blasting practices at the Higashitani mine involve the use of bagged ANFO, dynamite primers and non-electric detonators. Regulations in Japan prohibit the use of site mixed bulk explosives. Blast size is usually around 17 000 tonnes with 20 holes in a single row, two or three blasts are fired per day at a powder factor of between 0.25 and 0.32 kg/m3. As part of a program looking at oversize reduction Mitsubishi, Asahi and Orica agreed to conduct a joint project at the Higashitani mine to investigate the relationship between the powder factor and fragmentation. The first stage of the project was to benchmark the current blasting performance. Five blasts were monitored in each of the 210 (hard rock) and 220 (soft rock) areas of the mine. OricaÆs Powersieve« software was used to measure fragmentation and total rock breaker hours were also recorded for each blast. OricaÆs computer blasting simulation model Sabrex« was used to prepare revised blast designs with a higher powder factor and predict their performance. The performance of these blasts was monitored using the same methods.

Jan 1, 2004

By M. Ramulu, A. K. Chakraborty, P. B. Sahu, C. Bandopadhyay, P. B. Choudhury

Human response to blast induced vibration and air overpressure is an unsolved problem that accompanies excavation process in mining. Pre-assessment and understanding of annoyance due to production blasting is probably one of the most important aspects of a successful mining operation. Complaints arising due to unoptimised blasts lead to various critical situations that hamper production. Inspite, this important aspect has been covered by a limited number of researchers in the world and probably least in Indian context. Human response is a complex phenomenon and the sensitivity of individual also vary from person to person depending on various factors like age, sex, literacy, health and exposure to mining. With ever increasing demand of minerals, opencast mines are expected to approach habitats and thus mine management may witness increased response to blasting. Many developed countries have their own guidelines based on scientific analysis, addressing such environmental problems, where as there are a few studies available in India. This study introspects above phenomenon in tune with mining requirements by analysing direct human response. This paper is based on a case study regarding the human response to blast induced hazards in a Manganese mine situated in central India. Advanced techniques of Critical Path Method and Multiple Response Analyses have been used to unearth important inferences on the response of different crosssections of population residing about the mine to blast induced noise, ground vibration and air overpressure. Various inferences drawn may provide guidelines to the planners, environment or safety departments and blasting official for safe and environment friendly blast design.

Jan 1, 2004

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004