Search Documents

By Z. -E. Nakagawa, O. Yamamoto

After the formation of a concentration gradient of SiC within C-C composite, either zircon or mullite thin films were coated on the surface by sol-gel process. Oxidation resistance tests of as-prepared composites with a couple consisting of a ceramic thin film and a SiC-gradient were then carried out in air at the temperature range from 600 to 1600°C. By the coating of zircon with a thickness of 1.5 µm, a pronounced oxidation resistance was observed; the mass loss by oxidation was almost negligible at 1000°C and one hundredth of original composite at 1400°C. In the case of the coating of mullite with a thickness of 1.0 pm, the marked improvement in oxidation resistance over the whole temperature range examined, from 600 to 1600°C, was found with the combination of a SiC-gradient and a mullite thin film

Jan 1, 2004

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By John Emery, George Wang

Research and applied utilization activities for the increased use of ferrous and nonferrous slags in construction are presented. The overall use of blast furnace slag is relatively well known for a range of construction applications from aggregates to slag cements. In contrast to blast furnace slag, which is volumetrically stable and straightforward in its construction uses, steel slag contains hydratable oxides that can result in volumetric instability that must be dealt with through appropriate steel slag aging, testing and quality control to ensure its appropriate use. Particular care must be taken to prevent potential steel slag expansive behaviour in confined applications. Quality requirements and guidelines on steel slag expansivity to further the use of steel slags, with demonstrated acceptable performance, are outlined. There is a full range of proven construction uses - from aggregate to cementitious materials - for copper, nickel and phosphorus nonferrous slag. The use of air-cooled nickel slag is presented, based mainly on practical highway construction experience. It has been shown that air-cooled, crushed nickel slag can be an excellent aggregate in granular base, engineered fill and hot-mix asphalt. There is a good potential for increased ground, granulated copper and nickel slags use as supplementary cementitious materials that is being developed, which takes advantage of the 'latent energy' content. The scope of a new technical text in preparation on the technology of slag utilization is reflected throughout to provide a practical context for the engineer.

Jan 1, 2004

By A. R. Naji Meidani, A. Cameron, A. Richardson, M. Isac, R. I. L. Guthrie

The supersonic core of shrouded jets remain coherent over longer distances vs conventional supersonic jets. This phenomenon should allow for greater penetration of oxygen into slag/steel reactor systems. As such, they hold the promise for faster slag/metal mixing in BOF type metallurgical reactor systems, possibly creating greater surface area/volume ratios of reacting phases, and thereby faster kinetics, as compared to conventional supersonic jet systems. In order to assess the potential of shrouded supersonic jets versus their conventional counterparts, an experimental investigation of impinging shrouded supersonic jets into a water model of a simplified BOF system was carried out in the MMPC's water modelling laboratory. The experimental results for three different designs of a shrouded supersonic jet nozzle have been compared in terms of greater penetration depths and reduced mixing times. Based on a novel dimensional analysis, the depth of penetration of a gas jet into a liquid bath is shown to depend on the nozzle-bath distance, the liquid's Froude, Reynolds and Weber numbers, reflecting the ratios of gravity, viscous and surface tension forces to the jet's inertial, or momentum, forces. Good agreement between the mathematical model and experiment was obtained in terms of predicted and observed depths of penetration. Further efforts have been made to study jet penetration into liquid metals. The effects of mean liquid density of slag/metal mixtures and a wide range of gas flow rates on the penetration depth were investigated theoretically. The results show that the penetration depth can be increased with increasing gas flow rate and decreased bath density.

Jan 1, 2004

A model has been developed for drum scrubbing which allows selection of geometry and power input. Specific aspects considered are: Calculation of total static and operating volumes. Total residence time based on total operating volume. Solids residence time based on solids operating volume. Selection of the aspect ratio. Alteration of operating fill to allow for smaller or larger feed openings. Selection of proportion of critical speed. Calculation of shell and motor power requirements. The model uses either solids or total residence time to calculate the required operating volume. The solids residence time is based on the proportion of coarse solids in the feed. Material finer than the reject size is considered as part of the slurry. The solids operating volume is the static volume plus the surcharge on the discharge weir required for flow of the solids from the unit. The total operating volume is the static volume plus the surcharge on the discharge weir for the total flow to exit the scrubber. The burden density is calculated from the coarse solids bulk density and the slurry density that includes all the fine solids. Power is calculated using the Liddell and Moys correlations for burden position and shape, and the operating rotational speed. Results from the model (especially power) have been verified from industrial installations of significant size. Predicted and observed power draws are within two per cent. A check against the JKMRC mill model shows power draw prediction agreement to within four per cent.

Jan 1, 2004

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By Sri C. Sawmliana, P. Pall Roy

Damage to underground roof and pillars in blasting gallery (BG) panels has been an increasingly important area of study in recent years due to the invention of new explosives and cord systems which has led to the modification and alteration of the design aspects developed by Charbonnage de France (CdF). According to extensive mine experiments conducted by Indian and foreign experts, it has been established that the induced peak particle velocity (PPV) is predominantly related to the emanated seismic energy of a source and the distance from the source. With that concept in mind, nearly 160 experimental blasts were carried out in four BG panels in India under varying geomining conditions. Based on the results obtained thus far, the authors have established predictor equations correlating explosive energy (in Joules) and distance from the shot to that of induced peak particle velocity received at the sensor point. Good correlation was obtained between the actual and the predicted values. It is realized that this equation may be used as an efficient tool to determine the size limit of blasts in BG panels so that the induced particle velocity does not create damage in underground workings as per the established Blast Damage Index (BDI) and other available safety norms.

Jan 1, 2004

By Y. Mao, D. Xie

The viscosity of TiO2-containing blast furnace slags may increase rapidly (commonly referred to as thickening) under strong reducing conditions in the blast furnace. To elucidate the mechanisms for slag thickening, measurements have been made of changes in the composition and rheological properties of TiO2-CaO-SiO2-Al2O3-MgO slags during the reduction process. The slag composition covered the range of 17–33 wt% TiO2, 9–19% Al2O3, 8–16% MgO and theCaO/SiO2from 0.8 to 1.4. The viscosities were measured using the rotating cylinder method at temperatures up to 1550ºC and the fusibility temperatures were determined from ‘breaks’ in the viscosity-temperature curves. The reduction of the slag was carried out in graphite crucibles at1500ºC for 2–6 hours The rheological properties of the slags during reduction were predominantly influenced by the slag basicity (CaO/SiO2), and the effect of other components depended largely on basic or acidic behaviour of the oxide. The reduction of TiO2in the slag by carbon was initially fast to formTi2O3, followed by further reduction to TiO and TiC. Correspondingly, the viscosity showed initially a slight decrease, followed by a gradual and then rapid increase. The thickening was found to be accelerated by an increase in TiO2content and a decrease in the CaO/SiO2in the slag. In addition to the existence of 1~3 wt% TiC, the thickened slags also had a significant amount of TiO (3~7 wt%), suggesting that TiO may play an important role in the ‘thickening phenomena’ ,possibly by forming solid solutions with TiC to significantly increase the number of solid particles in the heterogeneous slag. Keywords: TiO2slags, viscosity

Jan 1, 2004

By Pravin Mathur

"Praxair's CoJet® technology was introduced in 1997 to effectively inject chemical energy in electric arc furnaces. Coherent jets were invented as a revolutionary means of injecting oxygen and other gases into the EAF and into converters. Today, steel makers have widely accepted this concept in over 70 EAFs worldwide. Indeed, the whole industry has shifted to this new standard for chemical energy input in EAFs. CoJet® technology has also been implemented successfully in BOF converters.This paper will review the principles of coherent jets as applied to steelmaking. The key learnings garnered from several furnaces are also reviewed. In addition, while the CoJet® program has been widely accepted worldwide, based on steady feedback received from customers and the market place, several programs are underway in development and commercialization. These enhancements and new applications of CoJet® technology are also overviewed in the paper."

Jan 1, 2004

Jan 1, 2004

By R. J. Fruehan

Slags have many useful functions in iron and steel making. In particular, slags are used to remove impurities such as sulphur, phosphorus and inclusions from the metal, and a large amount of research has been done in this area. Slags also insulate the metal thermally and form reactions with the atmosphere such as reoxidation and nitrogen pick-up. However, slags serve other more unique functions, several of which are reviewed in this paper. The role of slags in new iron smelting processes with regards to reduction of ore and gaseous desulphurization are discussed. In iron smelting processes, much of the reduction occurs by the reaction of carbon in the char and the metal suspended in the slag with iron oxide dissolved in slags. The slags also react with the gas resulting in sulphur removal from the process. The mechanisms of these reactions and pilot plant data for these processes are given in this paper. Slag formation within ferrous burden materials affects the cohesive zone and the performance of the blast furnace. Recent theoretical and experimental findings on this topic are presented. In the electric arc furnace, foamed slags are used to allow for higher power operation and productivity. Of particular interest, foaming in stainless steel production is more difficult than for normal steels. The foam index, or the ability of the slag to foam, for stainless steelmaking is similar to that for carbon steelmaking slags. The poor foaming is due to the lack of gas generation for the foam. Methods to increase foaming in stainless steelmaking are discussed.

Jan 1, 2004

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By C. J. Badenhorst

Occupational illnesses and diseases tend to be chronic and are generally characterized by temporary or permanent physical dysfunction. With the exception of some symptoms, they are not generally visible. Therefore, safety overrides health in mining because occupational ailments take years to develop and management observes less physical trauma, if they witness anything at all. Occupational health issues need to be addressed systematically, encompassing all aspects of the interaction of employees within the work environment. Risk assessment is central to the management of occupational health. This should not be seen as a complex process and may involve little more than simply considering the consequences of one?s actions before starting work. Competent risk assessment provides the starting point and defines the scope of further action. The objectives and final use of an occupational health risk assessment determine the process and the method by which it is carried out. The occupational health risk assessment is therefore a systematic procedure to identify potential health hazards, evaluate the extent of exposure subjectively and/or objectively, and to establish the need for, and effectiveness of existing control measures. Furthermore, it facilitates the drafting of occupational exposure monitoring, medical surveillance and occupational health education programmes. Various models for conducting occupational health risk assessment provide step-by-step guidance for the identification and assessment of significant occupational health hazards and assist in producing suitable and significant occupational health risk assessments. The paper gives an overview of an occupational health risk assessment model based on the basic principles of occupational health and the legislative requirements, which will simplify the occupational health risk assessment process and ensure a sound base for the development of all other occupational health systems.

Jan 1, 2004

By M. Leduc, M. Backens, M. E. Smith

An emerging technology for sustainable development in mineral development, tailings co-disposal™ is a means to dispose of conventional mill tailings within the void space of a waste rock dump. This method, while not applicable to all tailings systems, can offer a significant reduction in short-term and long-term environmental liability, land disturbance, closure costs, and negative public image. The concept is to dispose of the tailings simultaneously with the waste rock or leach ore, controlling the ratio of tailings to coarse material such that the resulting dump is stable both physically and chemically. The resulting co-disposal dump can be as safe as a conventional waste dump. In the case of alkaline tailings in a potentially acidic waste dump, the acid production can be buffered or slowed.

Jan 1, 2004

By Zahra Hosseini, S. Hassan Khoshroo, Mohsen Amirrahmat

The Sarcheshmeh Copper mine will be developing its open-pit in order to reach to the remaining ore in the deposit. One of the problems regarding the development plan is the ore handling system from the pit. After its development, the pit depth and its daily production will be increased. Therefore, the present transportation system (shovel and trucks) can no longer be used efficiently. It is necessary to use a new system that can reduce transportation costs and handle the new amount of blasted material at the same time. Studies show that an in-pit crusher and conveyor belt is the most suitable system that could be used in this situation. One of disadvantages of the conveyor belt, however, is its limitation in the particle sizes that it could carry. Consequently, size distribution resulting from the fragmentation process is an important parameter in choosing an efficient conveyor belt system. The size distribution of the fragmentation process also affects the operations following blasting. The determination of this parameter allows the optimization of blast design and explosives. Hence, during this project, the size distribution of blast fragmentation in the different types of ore at the Sarcheshmeh mine was determined by the image analysis technique. Numerous digital pictures were captured of the different blasted faces to prepare a representative sample of each kind of rock. They were then analyzed using the GoldSize image analysis software. Results show that fragmentation in the blasted rock is relatively high. It is therefore expected that an appropriate conveyor belt could be selected for further developing the open-pit mine at Sarcheshmeh.

Jan 1, 2004

By J E. Lynch

The Mt Leyshon gold deposit produced in excess of three million ounces of gold and considerable silver over a period of approximately 130 years. Most of this production occurred between 1987 and 2001. Mining commenced in 1872, however it was highly likely that Chinese miners were not only removing alluvial gold from the area but were also mining very rich æreefÆ gold. Records for early alluvial and hard rock mining do not exist, however gold production was probably considerable. In the early 1980s Marathon Petroleum (Australia) Ltd (MPAL) joint ventured into the Mt Leyshon area which had been held as a mining lease by Noranda Australia Ltd since 1968. Noranda at that time was concentrating its exploration effort on the Balcooma base metal prospect areas to the north of Charters Towers. In early 1982 MPALs parent company was taken over by US Steel. This led to an opportunity for MPALs Australian management to purchase all tenements and licences (except for coal, oil and gas) which were duly purchased for $US 1 million. At this time MPAL had a remarkable array of gold tenements (many of which were subsequently mined by other companies) and Mt Leyshon was considered to be the highlight. Early æseedÆ capital ($A 3.1 million) was raised with backers being the Bank of America, the NSW Government Superannuation Scheme, Westpac, private individuals and a Queensland grocery chain by the name of æJack the SlasherÆ.

Jan 1, 2004

By Jiang Fan, Wang Haigang

"The three-dimensional complex multiphase turbulent flow in U-beam separators was simulated using the Reynolds stress equation models (RSM). To account for the effect of the stochastic characteristic of the instantaneous gas velocity on the particles, the improved Lagrangian stochastic model based on the Reynolds stress model for gas phase was adopted, which attributed to the successful prediction of the turbulence anisotropy and particle crossing trajectories effects. The interaction between the particles was also considered using the HardSphere model. To treat the particle-wall collision, the influence of the roughness of the wall on the motion of the solid particles was taken into consideration by imposing random collision angles. The result from this study not only shows the dynamic characteristics of the multiphase flow- in the separators, but also gives the relationship among the efficiency, structure and pressure losses of the separator.IntroductionCirculating fluidized bed (CFB) combustion is one of the most promising clean coal techniques. A main feature of CFB boilers is the un-delayed recycle of solid, coal and sorbant particulate, in an external loop. Separator, which is required to separate the solid particle from the flue-gas leaving the reactor of CFB, plays an importance role in the external solids recycle loop. It affects the combustion of CFB system greatly. Presently cyclone is the most commonly used as separators for CFB system and other chemical industrial processes. It provides high level of separation for CFB system for fine particles. However it suffers from some inherent disadvantages. It's volume and size is huge. Moreover, it is difficult to design and install when the CFB workload rises. The application of U-beam separators instead of hot cyclone separators in CFB boilers has many advantages. Publications indicate proposals or successful use of Ubeam separators in Swedenr11, USA 21, Russia r3land China [4]• But it is not possible to find results in the literature of detailed investigations of this new. type of separators or recommendations on the choice and calculation of an optimal design. For this reason, numerical simulation for the three-dimensional gas-particle two-phase flows with several rows of vertical U-beam elements, local in the chess order and blocking a way of outgoing from a CFB boilers dusted gases was carried out in this study."

Jan 1, 2004

By P. Dennis, T. Pieters, A. De Kievit, S. Ganguly

TEMCO has been producing manganese ferroalloys in submerged arc electric furnaces for over 40 years. The furnace linings all along have been of conventional insulation type until 2001 when a freeze lining of UCAR concept was installed for a 20 MW Furnace. Continuous improvement of furnace lining performance has been a key component in improving the business competitiveness of TEMCO. The expected minimum campaign life of the freeze lining is fifteen years as compared to the ten years of the conventional linings. The success of the freeze lining is very critical to the quanta and direction of heat flow through the lining that control the freeze protection. Under freeze protection can lead to reduced lining life and over freeze protection, on the other hand, can lead to operating difficulties and loss of smelting efficiency. It was, therefore, necessary to develop a computer based system to monitor and control the freeze protection. The computer based monitoring and control system uses the basic principles of heat transfer, activeX object and heat flux from dual thermocouples and that is reviewed.

Jan 1, 2004

By L. A. Cramer

South African platinum mines produce the world?s majority of platinum metal that is used in autocatalysts and jewellery. As the platinum market is forecast to grow at healthy rates into the future, the South African producers, Anglo Platinum, Impala, Lonmin and Northam, are planning to expand in the next decade. Furthermore, a number of smaller producers who are accessing other mineral rights are entering the buoyant market. The South African platinum mines have traditionally exploited the Merensky Reef of the Bushveld Igneous Complex (BIC); however, the mining of this reef is reaching depths that require significant vertical shaft systems and costly refrigeration for access to the orebodies at deeper levels. In the past decade all of the producers have begun to mine the less attractive UG2 reef because of its cheaper mining costs. This UG2 reef contains significant quantities of chromite with typically a chrome-to-iron (Cr/Fe) ratio of 1.35. UG2 ores can contain between 10 and 25% Cr2O3dependingupon the reef width and the selected mining method. It is relatively cheap and easy to extract a portion of the chromite from a platinum concentrator tailings stream at a grade of between 40?42% Cr2O3. However, it is only in recent years that some ferrochrome producers have begun to source some of their chromite from the tailings of platinum producers. South Africa is also the world?s largest single producer of ferrochrome and supplies much of the world?s stainless steel producers and thus the growing market for their product. As the traditional sources of high Cr/Fe ratio ores have been depleted at the shallow economic depths and thus have become more expensive sources of chromite, technical developments have improved the ability to use fine chromite economically to make acceptable grades of ferrochrome. Thus UG2 fines are now becoming possible cheap sources of acceptable feed to the ferrochrome industry. The abundance of feedstock for ferrochrome production and the lessening dependence on mined material will impact upon the structure of the ferrochrome business in South Africa. With continued platinum mining from UG2 reefs, South Africa is set to remain highly competitive in the world?s ferrochrome/stainless steel industry.

Jan 1, 2004

By K. G. Holley

Blasting is usually required to produce easily-excavated broken rock, while leaving surrounding rock masses as undamaged and stable as possible. In mining applications, it is common to utilise production blasting in the centre of an open pit, and specially developed limits blast designs when blasting adjacent to the excavation perimeter. In open pit blasting, limits blast designs generally include pre-splitting, trim blasts, or buffer blasts, all of which are designed to limit, or eliminate, damage beyond the designed pit wall. This paper reports on the findings of a study of the profile of damage in rock masses surrounding blasts, determined by a combination of vibration monitoring, displacement monitoring using extensometers, and video inspection of open holes drilled at various distances behind blasts. The results obtained suggest that the profile of damage may extend for the full depth of the bench, for distances of up to 12 to 15 metres behind blasts. This suggests that entire berms may be affected by blasting, displaying loss of friction and cohesion along joint and fracture planes. The study has considered production blasts and trim blasts with small diameter blastholes and pre-splits.

Jan 1, 2004