Search Documents

By Richard E. Ray

INTRODUCTION Main mine fan installations at underground coal mines must be designed to comply with the requirements outlined in 30 CFR (Code of Federal Regulations) Part 75. However, very little emphasis is typically placed on the aerodynamic optimization of shaft collar designs, ductwork configurations, and the selection of a fan isolation, or "closing door," system. Field testing has shown that poorly designed systems may produce large pressure losses between the shaft and fan inlet, as well as air turbulence problems which adversely impact fan efficiency and sometimes fan structural integrity. This paper analyzes each component of a surface exhaust fan system for an underground coal mine: • The shaft collar arrangement, • The 45 or 90-degree turning duct that isolates the fan motor from the return airstream, • Alternative ductwork arrangements for parallel fan installations, • The self-closing doors or dampers that are required for multiple fans, and • Horizontal and vertical evas6 arrangements on the discharge side of the fan. While discussion is limited to axial fan installations at shaft mines, most of the recommendations would also apply to centrifugal fan installations and to main mine fans for drift mines. FEDERAL REGULATIONS The mandatory safety standards for underground coal mines that apply to the installation of main mine fans are listed in 30 CFR Part 75.310. Stipulations which impact the design of the fan sys- tem arrangement are contained in paragraphs (a)(l), (a)(5), (a)(6),(d), and (1) of 75.31 0: • Each main mine fan shall be installed on the surface in an incombustible housing; • Each main mine fan shall be protected by weak walls or explosion doors in direct line with possible explosive forces; • Explosion doors or weak walls shall have a cross-sectional area at least equal to the area of the return air shaft or drift opening through which the pressure from an underground explosion would be relieved; • Each main mine fan shall be offset by at least 4.57 m (15 feet) from the nearest side of the mine or shaft opening; • Automatic closing doors shall be provided to prevent possible air reversals through the fans in mines ventilated by multiple main mine fans. The installation of main mine fans underground is prohibited by 30 CFR Part 75.310, (a)(l). Providing explosion doors or weak walls in line with a possible underground explosion and offsetting the fan 4.57 m (1 5 feet) from the edge of the shaft preclude the installation of the fan directly over the shaft. In addition, 30 CFR Part 75.507-1 specifies that all electrical equipment used in return air courses be permissible, which requires locating the fan motor outside of the airstream exhausted through the fan. To comply with the Part 75.310 regulations, explosion doors are typically located directly over the shaft as part of the shaft cover or 'bonnet." A sufficiently long section of ductwork placed between the shaft enclosure and fan, equipped with a 45 or 90- degree turn, enables the fan to be offset at least 4.57 m (1 5 feet) from the shaft and the motor to be isolated from the airstream. The need for the turn in the ductwork can be eliminated by driving the fan from the discharge side, instead of from the inlet side, and providing for a 90-degree bend in the evas6. For multiple main mine fan systems, self-closing doors can be located on the inlet or discharge side of the fan. FAN SYSTEM COMPONENTS A poorly designed exhaust fan arrangement will produce turbulent conditions at the fan inlet and significant pressure losses between the shaft and fan. Field tests have shown that pressure losses through inlet ductwork at some installations may constitute as much as 30 percent of the total mine head. Unfavorable flow conditions may cause a change in the operating point on the fan performance curve, resulting in reduced fan efficiency and pres- sure generation capability. In some instances, poor airflow distribution through the fan may create mechanical stresses that lead to fan blade or fan housing fatigue failures. The objective in designing an air duct arrangement for a fan system is to provide a low cost duct that will move the air from the shaft to the fan in a uniform air distribution and with minimum energy requirements. The optimum solution is a compromise between technical and economic factors. Aerodynamic design considerations for the shaft collar and cover, fan inlet ductwork for both single and parallel fans, self-closing doors, and evas6 are discussed in the sections below. Shaft Collar/Cover To prevent excessive turbulence and non-uniform air distribution through the fan, a smooth transition for the change in direction of airflow at the top of the shaft must be provided. However, the concrete lining of the shaft is abruptly terminated at the surface at many coal mine installations (see Figure I), creating a sharp 90-degree bend. The airflow exiting the shaft becomes heavily concentrated in the upper portion of the horizontal fan in-

Jan 1, 1997

By Lee W. Saperstein

The SME Research Council assists SME and its constituencies in establishing research directions that will benefit the mining industry and its professions. It also provides information about these directions to its membership, to government and to related industrial societies. The 1995 Research Forum, organized and chaired by George Luxbacher, was the second in a series of meetings organized to develop these directions. A copy of the full proceedings is available from SME for $12 plus postage and handling. The first research forum (Saperstein, L., 1993, "Technology for the Future, MINING ENGINEERING, Vol. 45, No 11, November, pp. 1382-85) invited mining industry representatives to discuss the unsolved technical problems that were keeping the industry from greater economic and environmental efficiency. The second forum asked academic researchers to discuss the same general topics from their perspective. It came as no surprise that, in general, the two sets of presenters tackled the same problems. There was no surprise when the academics spoke of the need for fundamental long-term research. What may have been surprising was the number of university people who spoke for near-term research that leads to measurable economic returns or savings. The closure of the US Bureau of Mines (USBM) has changed the objectives and attitudes of the SME Research Council. From being a point of liaison between SME and USBM - a conduit of items from each party to the other the council is now much more on its own. This isolation presents opportunities and hazards. The opportunities are exciting because the council could be the focus for mineral industry research policy if it were properly structured. The hazard is obvious - if there is no bureau, it could be argued, why maintain the council? Many people believe that SME should take the first course and become the beacon for research policy. More than ever, money is being spent on minerals industry research by the federal and state governments - particularly at the mineral-oriented land-grant universities - by industry and by consortia among these groups. SME could be at the hub of these programs. There is a general concern that industry is less able to maintain an economic edge by means of geologic discovery. According to Titley, there will be fewer major, new world-class discoveries except, possibly, at the continental and tectonic-plate margins. Consequently, economic advantage will go to those companies and nations that stay ahead technologically. Given the inevitable diffusion of technology, it can be concluded that technology development, underpinned by research, must be continuous to maintain profits. This is a change from earlier years when change would occur in relatively rare major steps that were interspersed with extended periods of technological equilibrium. Over the fiscal years 1994 to 1997, there has been a 24% cut in research spending by the Department of the Interior (figures from the American Association for the Advancement of Science). This is the largest budgeted percentage cut in research funding of any federal department. Even so, there is still a substantial amount of federal research funding expended in the mineral and extractive-energy industries. The US Geological Survey, Environmental Protection Agency, Departments of Defense and Energy and others expend substantial funds on minerals industry research. Industry - producers and manufacturers - is also spending large sums on research and research-like activities. This activity argues that there is a role for SME's Research Council. Providing focus Consortia. The closure of USBM has resulted in the migration of expertise to consulting firms and to other entreprenrutisl research entities. Many of these groups are creating ad hoc consortia among themselves, nearby universities and industrial partners. The Research Council is well placed to provide an open forum for these con¬sortia. Presentations of research results, as went on in the annual meetings of the Generic Mineral Technology Centers, can help to establish an. archive of results and an avoidance of duplication of research. A continuing sense of research directions can evolve. National Science Foundation. No discussion of consortia would be complete without mention. of the National Science Foundation's (NSF) programs for Industry/University Cooperative Research Centers (IUCRC) and Grant Opportunities for Academic Liaison with Industry (GOALI). NSF is aware of the gap in federal support of science and technology caused by USBM's closure.

Jan 1, 1997

By Jamal Rostami

With the recent technological advances; Tunnel Boring Machines (TBM) have become a viable economic alternative to drill and blast in hard rock excavation. These machines are finding increasing use in underground mine development due to the potential benefits they offer. The successful application of TBM technology to mining depends on the selection of the most suitable equipment and cutting tools for the rock and ground conditions to be encountered. In addition to required testing and geotechnical investigations, cutterhead design optimization is an integral part of the machine selection to assure a successful application of the machines in a specific project. This paper presents and discusses the back-ground of TBM application in a mining environment and the lessons learned, the process of conducting site investigation and the necessary laboratory testing together with machine selection and performance estimation for TBM use III mine development.

Jan 1, 1997

By Peter Raziszewski

"A ball charge dynamics model is presented. Simulation results are compared with observed data showing good correlation. Based on the charge dynamics models, a liner wear model is presented along with some wear simulation results. Using the charge dynamics model with the liner wear model, it is possible to envision the predictions of mill power consumption as a function of liner wear. Further work is needed to validate the liner wear model.IntroductionFrom a process control point of view, industrial systems can be considered stationary or non-stationary. For example, the physical properties, such as geometric and/or material, of a system considered stationary do not change with time. However, this is not true for non-stationary systems such as those found in the mining industry where process dynamics are often violent with wear being an intrinsic process phenomenon.In this paper, a model for ball charge dynamics will be presented along with a description for liner wear. Simulation results for power draft prediction using the charge model will be compared with observed data. Further, liner wear results will also be presented."

Jan 1, 1997

Best practice in environmental performance is a principle now increasingly and rapidly transferred around the globe. This matches both the greater rigour of environmental standards and the growing uniformity and `internationalisation' of standards for environmental management. There is no difference in the application of Normandy's environmental policy anywhere in the world.Normandy Mining is developing an Environmental Management System (EMS) which will satisfy:ò the need for technical excellence and best practice;ò the need to demonstrate `due diligence' in any jurisdiction;ò the need for financial statements and for insurance to reflect real world requirements for management of risk and liability.

Jan 1, 1997

By Jun Yuan

Kaolin clays from five different commercial deposits in Georgia were studied to understand the variations of zeta potential and related fundamental properties. The results suggest that higher negative zeta potential is related to exchangeable or soluble calcium ions in the clays.

Jan 1, 1997

Jan 1, 1997

By G. Beckstead, L. F. Sawatsky, R. Nutbrown, D. Long, G. Gould

"This paper presents a case study for optimizing water management at Gregg River Coal Mine located near Hinton, Alberta. The optimization study was derived based on a review and assessment of existing management practices and plans for future operation and final reclamation. A proactive water management strategy was developed to assist mine staff in adopting a rational, environmentally sound, and economical approach to water management. A plan was developed to provide for safe operation, self-sustaining operation, low maintenance, minimum negative environmental impacts, and anticipation of future needs for existing and future operations. A plan for final reclamation drainage was developed including establishment of effective, sustainable, and maintenance-free water management systems. The study demonstrated the importance and benefits of a proactive approach for integrated mine water management. This approach is recommended for other similar mine operations because it will improve environmental compliance and reduce costs of water management. IntroductionGregg River Resources Ltd. (GRRL) operates an open pit coal mine on the eastern slopes of the Rocky Mountains, located about 45 km south of Hinton, Alberta. GRRL opened the mine in 1982 and expects to continue operations after Year 2000. GRRL has progressively reclaimed the disturbed area and expects to complete mine-land reclamation shortly after mining in the area is complete. The existing disturbed area and reclaimed area covers approximately 9.5 km2 and will expand to about 10.5 km2 upon mine closure.Like other coal mines in the mountainous areas of Alberta and British Columbia, the GRRL coal mine is subject to highly variable temperatures and moisture conditions. Average monthly precipitation varies from a low of 12.6 mm in January to a high of 113.0 mm in August, based on the precipitation record at the mine site since 1982. Despite the relatively high rainfall during the spring and summer months, excess water problems during rainfall events are quickly replaced by water deficit conditions during periodic droughts. Surface runoff varies from near zero in the winter to a mean annual monthly maximum of 78 mm during the month of June. The mean annual surface water yield is 345 mm."

Jan 1, 1997

By Sheng Dai, Yuan Lee, Haiming Xiao, J. P. Young

"There are numerous analytical applications of scatter-emission and/or absorption spectroscopy applied to liquids and solids in the temperature range of 0 to 350°C. In this paper an all-silica fiberoptic probe is described which is useful for spectral analyses from 0 to 1600 K and can be used in harsh chemical environments. The probe has been used for Raman spectral analyses of many molten salt and solid material systems to 1000°C. It has applications for such studies at higher temperature ranges. The instrumentation required along with the demonstrated and proposed applications of the all-silica probe are presented and discussed.IntroductionThere are many kinds of scatter-emission spectroscopies that are of value for analytical measurements. Fluorescence, reflectance, arc or spark emission are descriptors for some of these. Raman scatter spectroscopy is also quite a useful technique for analytical measurements.In Figure 1, we give a simplified explanation of the Raman effect. If one shines monochromatic light into a sample, light may be absorbed, exciting the sample to some virtual state. We know from experience that almost all of the light is re-emitted in the same wavelength range. This is called Rayleigh or Mei scattering and is designated in the figure by the arrows in both examples that point up and down from the same lower energy state. A very small percentage (the order of 10-4%) of the monochromatic light is re-emitted leaving the sample at a vibrationally-excited state. Thus, this light is at a distinctly lower energy compared to the exciting radiation. This is called a Stokes shift and is represented in the left-hand example by an arrow descending to a more energetic vibrational state. If the sample is not at a temperature of absolute zero, some of this vibrationally excited state will be thermally populated. That portion of the sample still absorbs and re-emits exciting radiation as Rayleigh scattered light, but a small percentage of the exciting light is re-emitted as the sample relaxes to the lower vibrational state. The energy of this light is of higher energy and is called an anti-Stokes shift, depicted in the example to the right. Notice that the energy separation of the Stokes or anti-Stokes shifted emission from that of the exciting radiation is the same, and expressed in ~cm-I. The intensity of either shifted emission is a function of the population of the vibrational energy states; therefore, the ratio of the intensity of Stokes to anti-Stokes signal varies with absolute temperature. We will come back to this point later."

Jan 1, 1997

By D. C. Panigrahi

The paper presents the development of a thermodynamic based network analysis model. It uses transient heat flow algorithm for computing the heat flow from strata and predicts the environmental condition in different branches of the network. Along with the environmental condition, the mass flow distribution in network is computed by using nodal pressure method based on linear theory approach. The algorithm has been coded using object oriented programming approach and it has been validated in actual field condition. The correlation is satisfactory.

Jan 1, 1997

By Charles A. Kliche

The Comprehensive Environmental Response, Compensation and Liability Act of 1980 (CERCLA) established a national program for responding to releases of hazardous substances into the environment. The funding mechanism for this program is the Hazardous Substance Response Trust Fund (commonly referred to as Superfund), which provides funding for the implementation of removal and remedial response actions.

Jan 1, 1997

By R. Winand, M. Degrez, C. Temmerman

"The influence of the copper electro crystallization inhibitors (mainly thiourea, gelatin and chloride ions) is studied in a new fully automatic pilot plan. This paper describes the conception and the building of this plan. The new approach is to reproduce the experimental conditions observed in the industry with the three additives present simultaneously in the electrolyte and secondly to study the influence of a slight modification of the concentration of one inhibitor, the others being present in the electrolyte with their industrial nominalconcentrations.1. INTRODUCTIONDespite the fact that gelatine, thiourea and chloride ions have been used in copper electrorefining for a long time, precise knowledge concerning their influence on the cathode deposit, metallographic structure and associated properties is still lacking.Many authors studied the influence of each additive separately, or of two added at a time. Only a few authors studied the combined influence of the three additives added simultaneously. The general conclusion that can be drawn is that the combined influence is far from that forseen from the influence of each additive separately, or even from two additives used at a time. Moreover most of the experiments described in the literature were performed by adding all additives at once initially. It is however, well known that gelatine looses a great part of its activity during the first half hour due to degradation by sulfuric acid (as shown by the cathode overpotential drop). Thiourea is rapidly replaced by a number of degradation mole,cules and complex ions including cations from the solution, changing even the equilibrium between Cu, Cu(I) and Cu(II).Chloride ions are consumed by precipitation.A number of successive research projects [1-9] led pregressively to the concept that, in order to obtain reproducible results representative of industrial cathodes, it was necessary to simulate as far as possible industrial conditions. It was essential that all additives were added continuously during the electrolysis, with, as consequence, a continuous bleed.The purpose of this paper is to describe the concept of a new fully automatic pilot plan for copper electrorefining and to present the first results."

Jan 1, 1997

By R. C. Hopper, A. A. Mathews, T. A. Lang

DESCRIPTION OF PROJECT The Straight Creek Tunnel site is located approximately sixty (60) miles west of Denver, Colorado, on Interstate Route 70 in the vicinity of Loveland Pass, in the Rocky Mountains. The ultimate project will consist of dual two-lane vehicular tunnels with a building at each portal to house mechanical ventilation equipment and other installations. The tunnels run virtually east-west on an ascending 1.64 percent grade for a distance of approximately 8,900 feet, and will pass beneath the Continental Divide at an elevation of about 11,000 feet above sea level. The maximum cover is 1,450 feet and each tunnel is approximately 48 feet wide by 50 feet high as excavated. The work now under construction consists of the North Tunnel, which initially will have two-way traffic. Ultimately it will be the west bound lanes for Interstate 70. The completion of the North Tunnel will be the fulfillment of a long felt need for better communication through the high Rocky Mountains of central Colorado and is a vital link in Interstate Route 70. The early planning for a vehicular tunnel through the Continental Divide began in the late 1930's and between November, 1941 and May, 1943 an exploratory pioneer tunnel

Jan 1, 1997

By Surendra K. Mishra

With increasing regulatory pressure from the environmental authorities, waste management has become a focal point of industrial operation. To offset the waste management costs, industry has made conscious effort to recover usable resources from the waste streams. This paper reviews the technical developments and current practices in processing of waste materials. Methods for recovering metallic, non-metallic and organic species from solid wastes and effluents generated by operating plants are discussed.

Jan 1, 1997

By Gang C, Changyi S, Liangde G

Geophysical and geochemical methods and techniques for gold exploration and their applications in China are summarised in the paper. Some case histories are also presented. The effect of prospecting for gold deposits using these methods is well illustrated through these examples.

Jan 1, 1997

By Thomas H. Koenning, James R. Boulton

The coal mined by Cyprus at the Shoshone mine near Hanna, WY is highly susceptible to spontaneous combustion. Spontaneous heatings have occurred in the gob of several of the longwall panels and, in some cases, following roof falls. Prevention and detection methods have evolved over the years as more has been learned about the occurrences. Seal design and construction have progressed to reduce air leakage into the gob. Pressure balancing has been successful as a supplement to good workmanship in reducing leakage. Early heating detection has improved as knowledge has been gained. Prior methods of detection relied upon thermocouples detecting a temperature change. Later a gas chromatograph was used to analyze gob gas samples. Initially the products of combustion (POC) were relied upon for detection. Most recently, lack of oxygen depletion in the gob has been used as an early warning of problems. Examples are presented to illustrate the evolution of spontaneous combustion control at the Cyprus Shoshone coal mine. Methods have been developed which minimize the oxygen concentration in the gob and reduce the potential for spontaneous combustion.

Jan 1, 1997

By Keith G. Wallace, K. M. (Chris) Chmura, Kirk H. McDaniel

The Waste Isolation Pilot Plant (WIPP) performed a feasibility analysis for the purpose of either modifying, supplementing, or replacing its two main mine fans. The WIPP, located near Carlsbad, New Mexico, is a U.S. Department of Energy (DOE) fa¬cility designed to demonstrate the permanent, safe disposal of U.S. defense-generated transuranic waste in a deep bedded salt deposit. Since the centrifugal fans were installed in 1988, multiple op¬erational and performance concerns have been identified. A com¬prehensive engineering study was conducted in 1995 to: 1) Qualify and quantify operational concerns, 2) Evaluate possible alternatives, and 3) Recommend an optimum solution. Multiple system modification and/or replacement scenarios were evaluated with associated cost estimates developed. The study considered replacement with either centrifugal or axial fans. Multiple fan duties are required at the WIPP. Therefore, Variable Frequency Drives and Inlet Vane Controls (IVC) were investigated for centrifugal fans. In-flight adjustable blades were investigated for axial fans. The study indicated that replacing the existing system with two double-width, double-inlet centrifugal fans equipped with IVCs was the best choice. This alternative provided the most desirable combination of: 1) ensuring the required operational readiness, and 2) improving system performance. The WIPP is currently planning to replace the first fan in 1997.

Jan 1, 1997

The Highlands Region of Papua New Guinea has 3 major national highways. The locations of these national highways are shown in Figure 1. The Highlands Highway begins at Lae City on the coast and passes through the Highlands towns of Goroka, Kundiawa and Mt Hagen. It terminates at Togoba approximately 10km out of Mt Hagen town. The Enga Highway begins at Togoba and passes through the towns of Wapenamanda, Wabag and Laiagam. It terminates at the giant Porgera Gold Mine. The Southern Highlands Highway also begins at Togoba and passes through the major towns of Mendi, and Tari. It terminates at Koroba station, near the Hides Gas Field. Two separate Feeder roads intersecting the main highway service both the Kutubu Oil Project and the Hides Gas Field. These national Highways play a very important role in the development of Papua New Guinea. Goods and services are delivered to the bulk of the population of the Highlands Region using these highways. Heavy machinery and equipment for the mining and petroleum projects of Porgera, Hides and Kutubu are transported using these roads.

Jan 1, 1997

Modem mineral exploration and development takes place within a data-rich context underpinned by a wide range of data acquisition, processing and interpretation technologies. This leads to requirements for consistent and explicit methods by which the relative risks - or success probabilities - of exploration programs can be assessed and communicated. Bayesian risk assessment methods are outlined which provide a starting point for this more rigorous approach to exploration investment.   Effective governance of information technologies becomes a core function of the modem competitive Board. As such it becomes a component of any business audit and any assessment of the quality and success potential of a company. Limited data however suggest that the average Board may be under-represented in this increasingly critical skill area.

Jan 1, 1997

By C. J. Preston, R. E. Ström, G. R. Baiden

"On January 1st 1996 Inco Limited, Tamrock OY, Dyno Explosives Group and CANMET formed a consortium for the development of robotic mining equipment. This project is a five year research and development agreement that combines the talents of the above organizations to facilitate the creation of mining equipment and systems for robotic mining.The projects are based on the communication system developed by Inco Mines Research and currently sold and marketed by Automated Mining Systems Limited. Main projects include the development and implementation of a positioning and navigation module (including a software mapping system that will be inherent to each piece of equipment), robotic systems for development and mining, and software systems to support the use of this equipment. Included in the program is the establishment of a test mine, at Inco’s 175 ore- body at Copper Cliff. This facility will allow collaboration of companies and research organizations for the design and testing of techniques and equipment for Robotic mining.This paper discusses the creation of this new research alliance, the Mining Automation Program or MAP."

Jan 1, 1997