Search Documents

By Y. Lin

The objectives of this investigation were to study the zeta potential characteristics of a Powder River Basin coal in water and to study the effects of zeta potential on the agglomeration of coal particles. The electrokinetic measurements show that the zeta potential of the coal is dependent on pH, temperature, coal concentration and contact time with water. The effects of various additives for changing the zeta potential of the coal were also evaluated. It was found that the strength of the coal agglomerates is increased when the zeta potential diminishes. Neutralizing the zeta potential enhances agglomeration. Therefore, it is important to control the zeta potential of coal to achieve optimum performance in coal-particle agglomeration.

Jan 1, 1997

By Gustavo Herrera Rico

As part of a general effort to increase safety, efficiency, and profitability of its mining operations, MICARE personnel with the support of NorWest Mine Services, Inc. determined that the key to improving development mining was the implementation of roof bolting as the means of primary roof support for both main entry and longwall gate road development. Until mid-1994, MICARE had relied exclusively upon primary roof support systems composed of heavy steel beams and wooden posts. Support systems were designed, implemented, and evaluated that were successful in controlling the mine roof under extreme geological conditions. This paper describes the geological challenges, support selection criteria, and presents the instrumentation and 'mine measurements made to assess the bolting performance during the development and retreat mining process of longwall mining.

Jan 1, 1997

By A. Tsubouchi, F. Noguchi, T. Takasu

"A high current density operation is desired to improve the productivity in copper electrorefining. However, a lot of problems still remain such as passivation at anode, dendritic deposition at cathode and impurity behavior during the electro refining.Effects of the current densitY on the morphology of copper deposition on the cathode, and passivation at the anode were investigated at various fluid velocity of electrolyte in the present study.Although a granular appearance of the copper deposition was obtained with increasing high current density, it was depressed by an increase of the fluid velocity of the electrolyte. A uniform deposition on the cathode was also observed when the fluid velocity of the electrolyte become higher. It was ascertained that passivation at the anode was suppressed by circulating electrolyte during electrolysis. INTRODUCTIONIt is desirable to operate at high current density in copper electrorefining in order to improve plant productivity without enlarging the size of electrodes(1). However, there are many problems in copper electrorefining at high current density with the usual commercial practice, for example, anode passivation, dendritic deposition and an increase of impurities in the cathode.In general, it is effective to agitate the electrolyte in order to suppress these problems(2). Smith et a1.(3) have performed electro refining experiments at various current densities in the range of 8 to 32 Aldm2 and at electrolyte fluid velocities in the range of 40 to 120 mlmin, and they obtained well consolidated, void free copper even at high current density in a high electrolyte velocity. However, they did not discuss the recovery ratio and the passivation behaviour at the anode. Walsh et a1.(4)(5)(6) experimented with the rotating cylinder electrode, and ascertained that electrolysis can be carried out at high current densities under the condition of pure electrolyte.With regards to anode passivation, there are several papers by previous workers(7)(8). Our group ascertained the process of producing anode slime during electrolysis(9). However, these experiments were carried out without forced circulation of electrolyte. Therefore, in the present study, to solve these problems, we electrolyzed at current densities in the range of 4 to 50 Aldm2 with circulating electrolyte in the range of 0 to 48 mlrnin. The effect of electrolyte fluid velocity on the surface morphology of deposited copper at cathode and passivation at anode were investigated when electrolysis were carried out with circulating electrolyte at high fluid velocity and at high current density."

Jan 1, 1997

Blasting is a very cost effective method of rock fragmentation but its uncontrolled application often results in excessive damage to the perimeter of an excavation. Several perimeter control techniques are available but tracer blasting is commonly used in Canadian underground mines for overbreak control. This involves tracing a column of Ammonium Nitrate-Fuel Oil (ANFO) with a detonating cord. In order to investigate the techno-economic effectiveness of tracer blasting in perimeter control, a field experimentation was conducted which involved blasting in sublevel caving and sublevel sloping operations, experimental drifting, benching and pipe tests.

Jan 1, 1997

By Du Sichen, S. Seetharaman, A. Jakobsson

"In the Present paper, the principles of oxygen potential measurements have been discussed along with the design details for oxygen sensors that are used in copper industry. A description of some of commercial probes is presented along with their salient features. The application of these sensors in flash smelting, converter and casting sections of copper production are discussed along with their implications on process optimization.I. IntroductionThe high temperature galvanic cells have come into prominence on account of their numerous applications in both fundamental as well as applied measurements. Since the inception of the oxygen-ion conducting electrolytes like ZrOrCaO·by Kiukkola and Wagner [1], the oxygen concentration cells have been extensively used in laboratories as well as in industries. In metal-production technology, these cells have been used to monitor the oxygen potentials in metallic, slag as well as gas phases and also to control and styr metallurgical processes. The pioneer among the various industrial users of such cells is the copper industry. To-day, high temperature solid electrolyte cells involving oxygen ion conducting electrolytes have become an integral part of copper pyro-refining and continuous casting. In the present paper some of the applications according to the industrial processes are described including the developments that are going on in the European scene."

Jan 1, 1997

By Loren G. Thompsen

The first high pressure grinding roll in a copper mine was commissioned at Cyprus Sierrita in July 1995. This grinding roll is the world's biggest operating unit. It has a roll diameter of 2.4 meters and a face width of 1.4 meters. It is driven by two, 2250 KW (3,000 HP) motors. This paper will discuss the development of the grinding roll at Cyprus Sierrita and what it has done for comminution of Sierrita ore. Maintenance and operating performance will be discussed as well as testwork including size reduction, power input, work index, and throughput.

Jan 1, 1997

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

By Koppe JC, Strieder AJ

The Rivera Crystalline Island (RCI) is an erosional window of the intracontinental Parana Basin that outcrops in the Rivera Department, north of Uruguay. RCI is made up mainly by Precambrian granites, metasediments and granite-gneisses. This island is crosscut by a dextral transcurrent shear zone system, the Rivera Shear System (RSS). The bulk strain ellipsoid was defined by previous work and has allowed the evaluation of shear dynamics. The geometry of the shear system is made up of two shear directions: E-W (P-shear), which turn right to NW-SE direction (R-shear), leading to the development of extensional bends. The shear zone system was developed in brittle-ductile to brittle regimes, under temperature conditions compatible with greenschist facies metamorphism. The shear zones are marked by an intensive fracture cleavage development. Mylonites develop only in narrow, discontinuous higher strain zones. Internally, the shear zones are dominated by intrusive rocks, mainly granites, dacites and diorites. Hydrothermal alteration has been developed in several areas.The economic significance of RCI is given by several small gold deposits, which have been exploited since 1869. One major new gold mine is under development, the San Gregorio Gold Mine. This gold deposit is locally controlled by a dilatant site where R-shear turns right to P-shear. Mine lithologies were deeply altered by hydrothermal fluids in the dilatant structure. This work presents the lineament-structural analysis carried out to identify similar structural patterns in all RCI sites favourable to host other gold deposits. The exploration program also considered remote sensing, geology, geophysical and geochemical survey.

Jan 1, 1997

By Peter Bellairs

It is generally expected that drilling and blasting be a routine part of a mining process where the blastholes are drilled, left for a period of time and then primed, loaded with explosive, stemmed and then detonated via an appropriate surface initiation system. The occurrence of a premature detonation(s) therefore results in a great deal of consternation and disruption to the mining operation.

Jan 1, 1997

By L. M. English

When plotted as head vs. volume, fan curves start high and decrease in head with increasing volume while mine head curves start low and rise with increasing volume. Their intersection is the system operating point But wait a minute: Isn't head loss a negative number, a debit? And isn't fan head an energy addition, a credit? This, as every ventilation instructor knows, is often a stumbling block to student or audience comprehension. It is possible to use the intuitively correct curves -pressure losses as negative values and energy additions as positive values -and still obtain the correct operating point: adding the two curves produces a third curve that intersects the x-axis at the operating point, the point at \\tIich the fan energy input exactly matches air circulation energy loss. Using this technique also makes it easier to account for outside influences on the system, such as natural ventilating pressure; with the standard approach it is quite easy to add or subtract such influences to the wrong curve. This approach can be extended to the graphical solution of any series/parallel circuit or ventilation net\wrk. The results are the same, and the approach is logically consistent and less confusing.

Jan 1, 1997

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By R. D. Lama

Coal mining is one of the major sources of methane release to the atmosphere by human industrial activities and is believed to contribute to -30% of the total methane emissions from industrial activities. In 1993, world saleable black coal production, attained almost 3.5 billion tonnes from which around 65% was produced underground. Coal in underground mines can contain high quantities of methane and some deep coal seams have methane content as high as 50 cubic meters per tonne of coal. Gas is re- leased during coal mining from the mined seam and in a higher degree from the neighboring unmined seams and gas bearing strata which are fractured as mining advances. This paper de- scribes a study which was undertaken to estimate the extent of methane emissions from coal mining in the world. Measured emission related data were collected from most underground coal producing countries in the world. The data included methane flows in the ventilation system, methane flows in gas drainage system, in-situ gas content, methane utilization and coal production. More comprehensive data were collected from a range of gassy and non-gassy Australian mines. Residual gas content of samples from run of mine were also measured. Using the Australian data, mathematical expressions were established to evaluate methane emissions as a function of coal production and in-situ gas content for other mines. These emission models were then used to evaluate the emissions for the countries or coal basins without measured emission data. Trends in methane emissions from underground mining for the year 2000 and beyond were also estimated.

Jan 1, 1997

By Charles H. Buclmam

"Environmental regulatory requirements for discharge of solutions and closure of operations for the gold mineral processing industry have been gradually lowered and in certain instances have been targeted to USEP A inorganic drinking water standards for dissolved ions in solution. The use of jar tests for water treatment process development is suitable for preliminary scoping work to be conducted in the research laboratory, as well as for optimization studies at the site of the treatment requirement. This paper will describe experimental methods which were performed using standard jar test equipment in efforts to produce solutions which meet USEP A inorganic drinking water standards after chemical treatment of cyanide solutions. The materials tested included gold bearing pregnant solutions from heap leaching operations, gold plant barren solutions from the Merrill-Crowe zinc cementation gold recovery process and gold heap leach wash solutions after carbon-in-column gold recovery. Experiments included cyanide destruction with sodium hypochlorite and arsenic and selenium co-precipitation coupled with mercury precipitation.IntroductionCyanide leaching solutions are used to selectively dissolve metallic gold from commercially viable mineral deposits. The heap leaching process involves stacking of gold bearing ores on specially designed solution containment pads and percolating alkaline cyanide solutions through the ore to dissolve the gold. Pregnant solutions containing the dissolved gold are collected and sent through a gold recovery process. After selective recovery of the gold, the barren solutions are recycled to the gold extraction process after adjustment of the solution alkalinity and available cyanide concentrations."

Jan 1, 1997

Pyrite is a significant gangue sulphide mineral in the Ok Tedi copper ore. Its presence in the flotation concentrate is not entirely desirable since it lowers the grade of the final copper concentrate. Lime depression of the pyrite has been practiced with some success. However, it has been observed that at the pH for pyrite depression a significant amount of the pyrite particles still float. To obtain further insight into the problem this work has been conducted to determine the composition, natural floatability and xanthate flotation behaviour of the various types of pyrite in the ore. The flotation results show that while some types of pyrite float well at high pH values, others are readily depressed. The implications of these results for Ok Tedi flotation plant have been Considered.

Jan 1, 1997

By John F. Vynne

This paper will discuss the application of available monitoring technology on blasthole drills with the goal being to reduce costs and increase productivity. Case studies from the monitoring of blasthole drills in North American open pit mines will be used to illustrate the ability to meet these objectives.

Jan 1, 1997

By C. Haycocks

The evolution of longwall mining is briefly traced from its inception in England in the 1620's. In the beginning this method recovered 90% of coal with roof closure controlled by packs and walls. Mechanization began with kerf cutting, crude face conveyors, and improved face support. Full face mining was accompanied by the introduction of self-advancing hydraulic supports. U.S. longwalls evolved a retreating system to recover blocks of coal outlined by room and pillar panels. Computer control combined with the most modern technology has greatly increased productivity. Past trends are used to predict future technological directions.

Jan 1, 1997

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy's program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997

By K. H. McDaniel

This paper describes the development of a Windows-based interactive mine ventilation simulation software program at the Waste Isolation Pilot Plant (WIPP). To enhance the operation of the underground ventilation system, Westinghouse Electric Corp. developed a program called WIPPVENT. While WIPPVENT includes most of the functions of the commercially available simulation program VNETPC from Mine Ventilation Services Inc. and uses the same subroutine to calculate airflow distributions, the user interface was completely rewritten as a Windows application with screen graphics. WIPPVENT is designed to interact with WIPP ventilation-monitoring systems through the sitewide central monitoring system. Data (e.g., air quantity and differential pressure) can be continuously collected from the underground ventilation remote-monitoring and control system and from the mine's weather stations (psychrometric data). Furthermore, WIPPVENT incorporates regulator characteristic curves specific to the site. The program utilizes this data to create and continuously update a real-time ventilation model. This paper discusses the design, the key features and the interactive capabilities of WIPPVENT.

Jan 1, 1997

By M. C. Ruiz

This work outlines the results of leaching studies on a copper concentrate containing chalcocite (Cu2S) and digenite (Cu9S5) with an acid saline solution of cupric chloride oxygenated at ambient pressure. The variables studied included the stirring speed, concentration of cupric ions, concentration of HCI, concentration of chloride ions, oxygen flow rate, temperature and time. The leaching system was found to be very effective for the dissolution of the concentrate. Over 95% of the copper was dissolved in 30 minutes with negligible dissolution of iron. The dissolution of copper increased with the stirring speed up to about 400 rpm and depended little on the total chloride concentration. The oxygen flow rate affected the dissolution of copper only below 0.1 1/min. The concentration of HC1 did not influence the dissolution providing its was sufficient to avoid the precipitation of copper oxychloride. The study of the effect of the temperature showed a maximum in copper dissolution around 90 "C

Jan 1, 1997

By Francis J. Arland

The installation of augered cast-in-place (ACIP) piles requires careful quality control to assure a successful pile installation. Unlike steel, pre-stressed concrete or other types of driven piles, which are shop fabricated, delivered to the site and typically driven to a minimum tip resistance, augered cast-in-place piles are installed to a pre-determined tip elevation or to a refusal criteria. The structural section of the ACIP pile is constructed during pile installation and cannot be inspected prior to installation. Therefore, a carefully administered quality control program is essential to a pile foundation that will meet or exceed design requirements. This requires an experienced team consisting of the Geotechnical Engineer, Contractor and Inspector. The focus of this paper is to discuss the responsibilities and duties of the ACIP piling Inspector. Qualifications of the Inspector The qualifications of the inspector are related to the complexity and difficulty of the proposed project. Ideally, the Inspector should be an individual with a degree in civil engineering with special emphasis in geotechnical engineering. A properly trained technician with geotechnical engineering experience working under the direct supervision of a geotechnical engineer may be able to provide competent inspection on some projects. It is important that the Inspector have a good understanding of subsurface and ground water conditions and how they will affect pile installation. The Inspector must understand ACIP pile installation procedures and be able to communicate with the Contractor, Structural and Geotechnical Engineers; and maintain a detailed pile record for each installed pile.

Jan 1, 1997