Search Documents

By C. J. R. Braithwaite, Giancarlo Rizzi

"Abstract-The Navan zinc-lead ore deposit (70 million tonnes) is hosted principally (97%) by the Meath Formation (Lower Carboniferous, Courceyan, Navan Group), comprising a lower, mainly carbonate mudstone unit, the Stackallan Member, and an upper grainstone-dominated unit. The Stackallan Member, about 60 m thick, comprises about 35 peritidal cycles including an oolitic grainstone interval. Grainstones forming the upper part of the formation, about 150 m thick, comprise at least six shallowing-upward ramp cycles. Emergence horizons are indicated by subaerial dissolution surfaces, in situ breccias, and a single palaeosol.Most dolomitization at Navan is confined to the Meath Formation. The linear dolomite body, trending NE-SW, has a flattened, laterally limited, tabular geometry in cross-section, suggesting that dolomitizing fluids initially rose vertically, cross-cutting stratigraphic and sedimentological boundaries, although fluid flow was subsequently controlled by these features. Three stages of dolomitization are indicated by textural relationships, cathodoluminescence (CL), oxygen isotopes, and fluid inclusion data. Stage 1 crystals, with generally dully luminescing cores and up to six overlying subsidiary zones, are the main replacive phase. Crystal surfaces are commonly corroded and overlain by bright stage 2 rhombs (which also form new nuclei lining molds and fractures). Three subsets of zones are present in stage 2 crystals: bright, non-luminescent, and dull; these are locally separated by additional corrosion surfaces. Stage 3 comprises relatively large baroque crystals, generally dully luminescent but with up to seven sub-zones. Isotopic and fluid inclusion data suggest growth of successive stages from waters which became progressively hotter (60°-160°C).The distribution of the ores follows the dolomite trend. Ores were precipitated between Stages 1 and 2 of dolomite growth, following Stage 2, and also during the nucleation and growth of Stage 3 crystals. Dolomitization and mineralization appear to have been temporally and genetically related. The cyclic sedimentation of the host rocks, which accentuates lithological and petrographical contrasts between depositional units, controlled dolomitization. The relationship between dolomitization and mineralization, which is closely associated with faults, provides powerful exploration criteria. The recognition of these features in limestones elsewhere in the Irish ore field may point toward unrecognized zinc-lead prospects."

Jan 1, 1997

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sulfur) coal which may be mined when the better deposits are depleted.

Jan 1, 1997

By E. J. McGuire, E. W. Brickle

INTRODUCTION Several recent technological improvements - largely by the convey-or industry - have increased the importance of inclined shaft construction for developing mines where ore deposits are relatively shallow. With these newer systems, long conveyor haulages are economically feasible, allowing mine owners to justify the expense of the inclined shaft or slope. What this actually means is that they can now take advantage of the versatility this construction offers. For example, haulage capacity can be changed by conveyor additions or replacements; equipment can be trammed to and from the surface quickly without costly breakdown and re-assembly; and a walkway is available for workers in the event of an emergency. Now, another innovation may accelerate this type of construction, the use of tunnel boring machines or "Mechanical Moles" to dig the slopes. While conventional. drill and blast methods have been used previously to build inclined shafts, the tunnel boring machine technique offers greater production rates, higher safety and a better, much cleaner bore. McGuire Shaft & Tunnel Corporation of Ft. Smith, Arkansas recently started such a slope project - the first ever bid by a contractor based on the use of a "Mechanical Mole".

Jan 1, 1997

By David Williamson

In the post-World War II years, metals analysts and statisticians have tracked the demand for metals in line with changes in Organization of Economic Cooperation and Development (OECD) industrial production (IP) growth rates, Williamson said. This was because the correlation between IP growth and metal demand was reasonable. "However, the correlation was exaggerated," he said. During times of expanding IP growth, metal demand increased at a faster proportional rate than IP growth. This was probably due to industry restocking in anticipation of growing demand at the start of each economic cycle. Conversely, metal demand would slacken at a greater rate than would be suggested by negative IP growth as industry destocked to reduce costs. Nonetheless, he said, a reasonable correlation could be painted between IP growth over the longer term and metal demand. "Yet, although this correlation has stood well since the last world war, it has been based on the fact that the bulk of the world's IP growth stemmed from the industrialized countries of the western world, lately including Japan," Williamson said. The so-called "developing world" had been of little consequence. The Soviet Union and other communist bloc countries were deemed to be closed, self-contained entities that, for each metal, would either be net exporters or importers, he said. These quantities would be used by analysts to calculate the overall supply/demand equation for the western world only and to deduce whether a commodity was in shortage or surplus. It is now believed that this method of projecting total world supply and demand for raw materials is outdated, Williamson said. It does not take into account the worldwide political changes that have occurred since the collapse of communism and the revitalization of China. "It is no longer appropriate to assess global balances for raw materials on the basis of three economic blocs," he said, including the western world, developing world and communist bloc. Rather, global balances need to be projected on a global basis. In this regard, since the collapse of communism and the removal of many other totalitarian regimes, capitalist forces are attempting to satisfy the expectations of the great mass of the world's poorer people, Williamson said. Such people, usually located in Asia, Africa and Latin America, have aspired to the same standard of living as people living in western Europe, North America and Japan. "Now, with free market forces at work, their aspirations will start to be met." Consequently, the demand for metals and other raw materials will now rise at a much faster rate. The production of raw materials has to keep pace with rising IP in the developed world. It will also have to keep pace with the demands associated with the rising expectations of increasing populations in the developing world, as well as from within the old communist bloc countries.

Jan 1, 1997

By A H. Clemens, T A. Moore

This paper discusses a number of technical issues related to marketing coal. It outlines how the results of research undertaken in New Zealand and overseas can help producers address a range of technical factors that impact on production costs and marketability. The paper also discusses trends in coal utilisation for power generation and how new technologies may require coal with different characteristics. Research and development into options for CO2 sequestration are discussed including carbon storage in forests, and removal of CO2 from flue or fuel gas in power stations, and its disposal.

Jan 1, 1997

By M. J. Fairweather

"The nature of minor element values and impurities are important both in the assessment of new properties and in the continuing improvement of operating plants. Impurity elements are frequently present as fixed solid solution impurities in association with the constituent minerals of a deposit or process streams in a concentrator. This paper uses five case studies to illustrate the application of simple regression analysis to the evaluation of minor element distribution in both operating mines and new deposits using analytical information readily available. This information maybe used to determine opportunities for improvements to the performance of an operating mine, to the economic assessment of anew deposit, or to the subsequent planning of an experimental study.IntroductionThe nature of minor element values and impurities are important, both in the assessment of new properties and in the continuing improvement of operating plants. Minor element values often contribute appreciable incremental revenue to a complex base metal deposit. Examples of valuable elements include precious metals, but may also include elements such as indium and bismuth which can be recovered at a profit by smelters provided with the necessary recovery circuits. During preliminary metallurgical studies of a new property there is usually a strong incentive to maximize the recovery of such valuable by-product elements. For example, the extent to which the by-product gold in a porphyry copper deposit is associated with chalcopyrite rather than pyrite may determine theeconomics of developing a new property.The nature of impurity elements in base metal concentrates is correspondingly important in minimizing the penalties which may be imposed by smelters in the treatment of such concentrates. Penalty elements include silica, dolomite (magnesia), arsenic, antimony, mercury, nickel and cobalt. The mineralogical association of these minor elements determines the ability of the mine to remove them in the concentrating process. This paper discusses means of assessing the mineralogical nature of such impurities without the use of sophisticated micro-analytical techniques."

Jan 1, 1997

By Ibil S

The Gameta Gold Deposit is located on the north-eastern corner of Fergusson Island in the D'Entrecasteaux Islands of Milne Bay Province, PNG, at lat. 9¦ 25' 5, long. 150¦ 47' E or AMG co- ordinate 256740 E/8959000 N (Figure 1). The area is covered by the Fergusson (SC56-05) 1:250,000 scale Topographic Map Sheet and the Koitabu (9079)1:100,000 scale Topographic Map Sheet. The property is held 100% by Union Mining NL (UMG) and lies 105 km NNE of Alotau and 33 km to the ESE of UMGs recently developed Wapolu Gold Mine, a Joint Venture between UMO (51%) and Macmin NL (49%). The inferred resource estimated from surface results and 105 RC drill holes, currently stands at 1.89 million tonnes at 2.6 git gold (1.0 g/t Au cut-off) or 155,000 oz. Evaluation of the property is currently proceeding. To date 111 RC holes have been drilled for a total of 4611 m.

Jan 1, 1997

By E. Ilgar

"Deposition studies were conducted in acid copper electrolyte to determine the influence of chloride ions on cathode morphology. A statistically designed screening test was carried out in the absence and presence of 20 ppm CI- using a three factor, two level factorial design, in an electrolyte containing 36 gl'! Cu2+ and 150 gl-! H2S04, The independent variables evaluated were agitation; current density and temperature and their influence on surface roughness was determined. The copper deposited at current densities where activation was the primary control mechanism appeared similar in morphology whether stirring was used or not. The addition of 20 ppm CI- to the electrolyte gave rougher deposits under the same conditions. In the mixed control regions, considerably rougher, dendritic deposits were obtained when CI- was present. Agitation was effective in reducing the copper surface roughness both in the apparent activation and mixed control regions in the presence ofCI-. The results of this study showed that 20 ppm Cl- polarized the copper deposition at low overpotentials but caused depolarization at higher overpotentials.IntroductionChloride ion is inherently present in copper electrolyte, either as an additive or from other sources such as make up water. The behavior of the chloride ion is well documented in electrorefining operations, but its role in copper winning is less obvious. However in both cases there is evidence that cathode growth and solution chemistry are strongly influenced by its presence. The mechanism and electrochemical action of the Cl"" have been shown to be very complex, therefore a better understanding of its influence on electrocrystallization is essential for improved cathode deposit growth control. It was proposed that Cl"" polarizes the copper deposition reaction at low concentrations due to CuCI formation but depolarization occurs at higher concentrations due to the formation of a soluble CuCI2"" complex [1,2]. Franklin [3] reviewed the mechanism of additives in the electrodeposition process and proposed that the Cl"" complexed with copper, adsorbed on the cathode as an induced anion leading to an increase in the reduction rate. At cathodic overpotentials less than 100 mY, lppm NaCl had a polarizing effect, i.e. an increase in impedance of the charge transfer step. At higher Cl"" concentrations up to 100 ppm, depolarization occurred as evidenced by a decrease in impedance, which was attributed to soluble cuprous complexes [4]."

Jan 1, 1997

By Gary PE Beerkircher

A brief history of banana screen development and evolution will be presented along with the operational advantages of the large banana screens available in the industry today. Applications of the large banana screens will be presented as well as the economic advantages that the use of large banana screens can offer to the Mining lndustry today. Banana screen installations in metal, non- metal and coal mining applications will be presented.

Jan 1, 1997

By L. -C. Lai

A series of LaNi5-based alloys, with partial substitution of Ni by Al, Co, or V, were prepared The gas-phase hydrogen absorption kinetics and pressure-composition-temperature curves were measured The activation became easier and the plateau pressure was reduced as Ni was partially substituted by Al Substitution with Co reduced the hysteresis as well as the hydrogenation capacity, but enhanced the absorption kinetics Vanadium is often considered as a hydride former, but when it was added to LaNi5, it was found that V occupied the B site. A small amount of substitution of Ni with V led to a higher hydrogenation capacity and faster activation rate Based on these properties, an alloys LaNia 25CO0.5V0.1Al0. 15 was fabricated as an electrode. Compared with LaNi4.85Al0.15, it was found to exhibit faster activation, higher discharge capacity, and longer cycle life. The variation of the hydrogenation characteristics is discussed based on the physical and chemical properties of the alloying elements.

Jan 1, 1997

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By Lawrence Devon Smith

The selection of the production rate is one of the most crucial decisions to be made in the development of a mineral property. However, it is not uncommon for the production rate to be decided arbitrarily, before any technical evaluations begin, and it is often not reconsidered when better data becomes available. A number of methods are used in the mineral industry to select the production rate for a project. There is general agreement that the size of the ore reserve has a strong influence on this decision, but what other factors are involved? Is there a way to identify an optimum rate? This paper examines the factors that influence the selection of a production rate from the perspective of project economics. The NPV maximum value should be viewed as a “failure” point. The “two times capital” maximum is proposed as a lower limit. A practical check is suggested to confirm that a selected rate is in an optimum range. Production rate assumptions are much more likely to be reviewed for marginal projects, but they should also be reviewed for viable projects.

Jan 1, 1997

By V. S. Sastri, M. Elboujdaïni

"Corrosion rates of silicon brasses, highzinc yellow brass, low-zinc yellow brass, leadedtin bronze and silicon bronzes in both permanent-mold and sand-cast conditions were determined in soft water of pH 3, 5 and 8, and hard water of pH 8 at 70°C by electrochemical polarization technique. The alloys in permanent- mold condition showed greater corrosion resistance than sand-cast condition. Corrosion rates obtained from weight loss measurements showed no observable trend of a difference between permanent-mold and sand-cast alloys.The corrosion rates decreased with increasing pH of the medium. Silicon bronze and silicon brass showed high corrosion resistance while leaded-tin bronze showed the least resistance. Addition of small amounts of aluminum improved the corrosion resistance of silicon bronzes and silicon brasses. Alloys in permanent- mold condition showed greater resistance to dezincification than sand-cast alloys when average pit depth parameter is considered."

Jan 1, 1997

By K. Osseo-Asare

Aqueous stability diagrams (25°C) are presented for the systems M-H2O and M-Oxalate-H2O where M=Sm, Nd, Co, and Fe. With the aid of these diagrams (i.e., Eh-pH and log[Metal]- log[Oxalate]), the solution-chemical constraints on metal dissolution and precipitation are identified. By comparing the corresponding stability diagrams, conceptual flowsheets are developed for metal recovery from Sm-Co and Nd-Fe-B magnet scrap.

Jan 1, 1997

By Fathi Habashi

"A process is proposed for the treatment of phosphate rock for the recovery of uranium and the lanthanides. The process assures the production of phosphatic fertilizers without polluting the environment with radioactive material.IntroductionWhile many processes for uranium recovery from phosphoric acid produced by the H2S04 route are known and utilised commercially, little is known about uranium recovery from phosphoric acid produced by the HN03 route1. Advantages of the latter route are both the elimination of the gypsum disposal problem, and the possibility of radium disposal in a controlled way2. Further, the lanthanides originally present in the rock can be recovered if the nitric acid route is used; they will be mostly lost in the gypsum produced by the sulphuric acid route3. In the present work a scheme for the recovery of uranium and the lanthanides from phosphate rock without interfering with the normal route for fertiliser production is proposed using HN03 as a leaching agent. Attention was also given to uranium decay products and their separation so that they might not contaminate the fertiliser4. Further, an attempt was made to defluorinate the leach solution in order to upgrade the fertiliser and at the same time recover the fluorine5. Rapid analytical methods for the determination of uranium, radium, and lanthanides in phosphate rock were developed6,7."

Jan 1, 1997

By S. Mathur, Pradip

Polyacrylic acid (PAA) was evaluated as a selective flocculant for the dolomite-apatite system. PAA with a molecular weight (MW) of 4 million was found to flocculate both dolomite and apatite. However, the flocculation behaviors of dolomite and apatite were significantly different with 450,000 MW PAA, which was found to be the lowest molecular weight fraction capable of flocculation. In single-mineral tests with a dosage of 2 kg/t PAA, 90% of the dolomite and 35% of the apatite flocculated. Selectivity was achieved in mixed mineral tests. From a feed consisting of an 80:20 mixture of apatite and dolomite, respectively, a concentrate containing 90% apatite was obtained with a 70% recovery. The dolomite rejection was about 75%, which corresponds to a 2% MgO content in the concentrate.

Jan 1, 1997

By Maynard O. Serbousek, Melvin E. Poad

Shotcrete, a useful support material in underground openings, is a sprayed concrete, and, when used with fast-setting agents, is immediately self-supporting. Although shotcrete has been used extensively for tunnel support, the technique has not been readily accepted by the mining industry because of the lack of essential information on such basic items as material properties and rock interaction. The Spokane Mining Research Center (SMRC) of the Bureau of Mines has been active in the field for the past 2 years, including research on fibrous reinforced shotcrete. IIT Research Institute, Chicago, under Bureau of Mines contract, is investigating physical properties of shotcrete as affected by (1) type of process (wet or dry) and (2) fast-set agents and controlle-dset cements. Already the contractor has shown the advantage of a regulated-set cement over normal cement and fast-set additives for the dry process. The regulated-set cements can produce high early strengths with no decrease in ultimate strength.

Jan 1, 1997

By Peter McDonald

In 1994 the world's largest underwater tunnel was constructed to link Canada and the U.S.A. This new tunnel was large enough to accommodate double-decker railway cars. The construction of an unplanned Retrieval Shaft was required to allow removal and servicing of the Cutterhead of the Tunnel Boring Machine before it passed under the St. Clair River. This paper, which is a revision of that published in Canadian Tunnelling, has been modified here to emphasize construction considerations and describes the evolution of the design and construction of this "Rescue Shaft" under extreme schedule pressure, and changed ground conditions..

Jan 1, 1997

By K. Y. Haramy, E. C. Westman

Anomalous geologic or stress conditions ahead of a longwall face have the potential of causing great harm to both the individual miner and the mining operation as a whole. NSA Engineering has been developing seismic tomography techniques to image the panel ahead of the face. This paper presents the results of afield effort in which a 60-m (200-ft) segment of a longwall panel containing a fault zone was surveyed daily as the face approached. Stress distribution, geologic structure and dynamic elastic properties within the panel were plotted and compared to static laboratory measurements. The surveys successfully imaged an anomalous stress concentration that was likely influenced by the presence of the fault zone. The calculated dynamic physical properties generally agreed with the laboratory measurements.

Jan 1, 1997

By Richard F. Coon

Six potential locations along the west shore of Lake Mead were evaluated to site anew water intake pumping station for the SNWA. The evaluations were based upon geotechnical exploration results and conceptual intake pumping station designs. The exploration included geologic mapping, geophysical testing, underwater ROV inspections and borings. Ground surface and underground chamber pumping station designs were considered. Sites at Saddle Island, Black Canyon and Hoover Dam are geotechnically suitable. A Saddle Island site was selected because it has the most favorable conditions for the intake pumping station and the aqueduct to the Las Vegas valley.

Jan 1, 1997