Search Documents

Copper refining electrolytes are maintained in the range 60-65¦C to ensure an efficient operation. The heat energy required to meet these temperatures has been traditionally derived from the electrical energy required for the electrolytic process and supplementary steam energy. In 1983, experiments were conducted at Copper Refineries Pty. Ltd. (CRL) to determine the effects of insulating the Tank House cells, and fully covering the cells. The results of these experiments showed conclusively that greatly reduced steam consumption would be required to maintain electrolyte temperatures. These positive results led to an Energy Conservation Programme for the Tank House, and this was implemented in 1984. A computerised cell cover monitoring system was developed, and is used to control cell coverage and fluid balance. The experimental work and the benefits obtained since implementation of the programme are discussed.

Jan 1, 1985

By Madhu G. Ranade

A statistically designed pot grate- kiln test program was conducted to determine the agglomeration process variables necessary for increasing the low temperature disintegration resistance (LTD) and reducibility (R40) of magnetite-based Empire acid pellets. The ASTM tumble index and compression strength were to be maintained at an acceptable level. Six process variables, bentonite addition level, preheat time and temperature, firing time and temperature, and cooling rate, were investigated within the constraints of the Empire plant. The bentonite addition level and firing temperature had the largest effect on pellet properties. The results of this program were verified during a pl ant trial. The target firing temperature at the Empire Plant has been decreased for increasing the LTD and R40 of commercially produced Empire pellets

Jan 1, 1985

The nickel refinery at Yabulu consumes an average of 118,000 kg/h of low pressure steam in stripping operations to-recover ammonia and carbon dioxide from product liquor and ore tailings streams. The steam used in the stripping operations is produced from the 25 MW power generation plant at the refinery. The back pressure on the non condensing steam turbines is maintained at 60 kPa.Studies have been carried out to determine the optimum amount of steam required to be generated for stripping operations. When steam production is increased, the product liquor flow from thewashing thickeners can be increased. This results in improved washing efficiency of the thickeners and therefore improves the plant nickel recovery. A computer thickener wash model was used to predict nickel recoveries at varying steam consumption rates.The studies have shown that in most plant situations, it is not economical to-generate more steam than that already available from existing power production.The studies also highlighted the necessity to use all steam generated from power production at all times to maintain maximum nickel recovery.

Jan 1, 1985

By Hutchings AA

This paper describes MIM's experience in arranging and executing project financings for coal projects at Oaky Creek and Newlands and Collinsville and the port facility of Abbot Point.The financings had their origins in the late 1970's and culminated with the opening of these projects during 1983 and 1984.MIM's financing developments therefore span an important period in the development of resource projects in Australia.Resources projects have been growing in both scale and complexity of financing requirements.

Jan 1, 1985

By Walter R. Jr. Hibbard, William A. Vogely

INTRODUCTION Volatile markets and pricing, increasing imports, constraining but effective laws related to the environment, health and safety and price controls lead to concerns which generated pious laws stating non-fuel policy and authorizing studies but resulting in ineffective implementation. Several commissions, reports by the Secretary of Interior and even the President have led to many recommendations but little or no action. No single comprehensive policy could solve problems which are diverse, commodity specific and not categorizable (Landsberg 1982, 1983). Thirteen laws administered by 27 agencies regulate or affect minerals and materials. Political instability created by communist regimes in Southern and Central Africa jeopardized sources of critical imported materials. This situation led to a Resource War mentality. It was feared that the U.S.S.R. was seeking to control this area and exclude the United States from resources (Vogely, 1980). The success of the Organization of Petroleum Exporting Countries with a petroleum cartel led to fears of an Organization of Minerals Exporting Countries which might create more cartels and/or make the existing ones more effective. Economic needs of developing countries required export to maintain employment and balance of payments have led to world surpluses, weak markets, low prices, and large loans from the World Bank which have under- mined U.S. industry (Landsberg, 1982a). Un- cooperative environmental laws, obsolete facilities and non-competitive costs have led to shipping U .S. ores to other countries for processing into ingot and bars which are imported back to the United States. Yet massive internal turmoil has interrupted supplies, and led to un- certain availability and higher prices. This situation could happen again. Included in this category of critical materials with uncertain sources are metals required in the manufacture of military aircraft, which has led to concern regarding the defense industry base (Morgan 1983). Remedies have been proposed which include: updated stock piles, material substitution, international cooperation and coordination, foreign policy aimed at resolving racial and national stresses in South and Central Africa, relaxing U.S. environmental and public land regulations and action under the Defense Production Act (Goth 1982). The President's report (1983) to Congress has stated a national materials policy which recognizes: that materials play a critical role in our economy, defense, and standard of living; that public lands contain a vast untapped mineral wealth; that the role of government is to identify mineral issues and act on them; and that there is a need for long term high potential pay off research (Bureau of Mines 1983). There is a serious question as to whether or not a comprehensive national mining, minerals, and materials policy is feasible let alone necessary. One solution is to abandon the attempt at comprehensiveness and to target specific is- sues with realistic policies (Comptroller General 1979). In the following sections, the major studies of the 1970s will be reviewed, major issues yet to be faced will be identified, the principles involved in these resolutions will be reviewed,

Jan 1, 1985

By Dennis E. Bell

"This paper describes exploration and development to 1982 in the southern half of the northeastern British Columbia (Peace River or Northeast Block) inner foothills metallurgical coal belt. Gates Formation, Fort St. John Group, is the primary target; Gething Formation, Bullhead Group, is secondary. This part of the belt remains wilderness when compared to its other parts. Practical formational and structural mapping is described. A local problem known as the Secus Mountain or Mount Belcourt conglomerates is discussed. The three major explorers have been Denison Mines, PetroCanada, and Crows Nest Resources, all with partners. Initial mine construction and rail spur construction are continuing. The new town of Tumbler Ridge is being built. Introduction This paper describes exploration and development to 1982 in the southern half of the northeast British Columbia metallurgical coal belt. The area (Fig. 1) trends 120 km northwest from the Alberta border to the Wolverine River and Bullmoose Creek. The belt averages 15 km in width, and is 20 km at its widest. Physiographically, the area is dominated by rugged inner foothills, with relief to 1,500 m. The trend of the structures is transected by a dozen rivers flowing southwest to northeast away from the Continental Divide. The Rockies, lying immediately to the west, control the climate. One fact continues to colour all coal work in the area. When compared to the other parts of the western Canadian foothills and Rockies coking belt, it remains the least accessible and least mapped portion. Lack of access also makes all work expensive. Current activity centres about two mines in construction at the northwestern end of the area. Denison Mines and partners are developing their Quintette project, and Teck Corporation and partners are developing their Bullmoose project. PetroCanada and partners have intensively explored their Monkman-Duke Mounta,in project, but mine construction awaits better economic times. The rest of the area remains lightly explored, with the exception of some intensive work on particular structures by Denison and Petro-Canada. The focus of coal work has been metallurgical bituminous coal seams contained primarily in the Gates Formation (Fig. 2) and secondarily in the Gething Formation. These formations are found in generally en-echelon structures ranging to several kilometres in width."

Jan 1, 1985

By V. Y. Kirillin, V. A. Rumjantsev, S. A. Tchesnokov, Yu A. Veksler, V. F. Kalmykov, A. N. Telgarin, A. T. Shakirov

Mining in outburst hazard seams may be safe and effective if some preventive measures, such as lowering gas and rock pressure as well as speed regulating of a continuous miner in cutting the seam would be practised. The driving speed should be optimal as the low speed lowers labour productivity but the high speed may cause gaso-dynamic phenomena. At this mine the driving speed is regulated by seismo-acoustic control of the seam condition.

Jan 1, 1985

By W. J. Witte, M. K. Witte

"The purpose of this report is to present a generalized preliminary design and cost estimates for a typical heap leach operation such as might be undertaken in Northern Ontario. This report should be of value to anyone in the mining industry planning, or contemplating, a heap leaching operation in Ontario, either on a large or small scale. While more detailed costing and design work will obviously be required for each specific project being contemplated, the data provided in this report should enable parties to make preliminary estimates of the costs of proposed projects and should identify most of the planning and design parameters that will need to be considered.Although heap leaching has been used extensively as a low cost gold recovery method in other parts of the world for many years, it has only recently become of interest to the Canadian mining industry.In order to investigate and demonstrate the feasibility of using heap leaching in Ontario, the Ontario Ministry of Natural Resources in 1982, undertook to locate a private sector proponent willing to undertake a 10,000 ton demonstration project. This project was to have been carried out at a production scale under normal northern Ontario field conditions. The Ministry was to have provided technical management and design for the designated project."

Jan 1, 1985

By J. Carr

Ring gear and pinions used as the final drive on large metallurgical grinding mills are expected to transmit their rated horsepower reliably for long periods of time. Duty is 24 hrs./ day. Life expectancy of such gear sets is of the order of 20 years; that is, each gear and pinion flank is expected to resist failure by pitting for 10 years. This means that for a dual pinion gear set having a ratio of 18.42:1.0 and a mill speed of 10 RPM, every gear tooth will see 105.12 x 106 surface contact stress cycles and every pinion tooth will see 968.15 x 106 surface contact stress cycles in a 10 year period. The allowable surface contact stress on the gear and pinion is determined by the material hardnesses. The rule being the higher the hardness, the higher the allowable surface contact stress may be.

Jan 1, 1985

By James W. Bass

Atmospheric fluidized bed combustion (AFBC) is an improvement in coal-fired boiler design that offers several advantages over conventional boilers. AFC can meet sulfur and nitrogen oxide emission regulations without the need for add-on flue gas treatment equipment. The relatively low combustion temperature inhibits ash melting, thus reducing slagging and fouling which can, in turn, increase a boiler's fuel flexibility. This report discusses, in general, AFBC technology and, in particular, progress at the 20-MW Pilot Plant built by the Tennessee Valley Authority (TVA) at its Shawnee Power Station near Paducah, Kentucky.

Jan 1, 1985

By Jurgen H. Kleinau

This paper details Keeler/ Dorr-Oliver's experience with the application of fluid bed combustion technology to the burning of coal-mining waste. The designs of two stage fluid bed combustors/dryers are demonstrated as useful in the drying of coal, slag and coke, using coal and coal refuse (gob) as fuel. Anthracite mining refuse (culm) is more than abundant in Northeastern Pennsylvania. After demonstration at Shamokin, Pennsylvania, a full commercial-sized fluid bed boiler using culm is used for district heating in Wilkes-Barre, Pennsylvania. Limited research work has shown the utility of using fine coal as filter aid in sludge in¬cineration. With the rising avenues of the suitability of coal as auxiliary fuel in fluid bed sludge incineration, an expansion of these concepts combines the use of coal or coal refuse as filter aid and auxiliary fuel. Lime¬stone addition controls SO2 emission.

Jan 1, 1985

The strategy of adjusting operating conditions to maintain optimum process performance as the feed quality varies - adaptive optimisation - is being investigated by computer simulation of chemical processes for the treatment of ores. Those ore-process systems that are most likely to yield substantial benefits from adaptive optimisation are being identified as a guide to the selection and development of systems for practical application. The generalised mathematical representation of the cost structure, ore quality variations, process kinetics, reactor characteristics and operating variables for ore-process systems is described. Results are summarised for temperature, reagent concentration or residence time as the manipulated variable. For almost all systems, adaptive optimisation was economically beneficial, although a few exceptions have been identified where there is a significant synergistic effect between poor-performance and good-performance materials in a blended feed. The sensitivity of the benefits of adaptive optimisation to a range of economic and technical factors is summarised.

Jan 1, 1985

By James E. McNulty

Coal reserve estimates are prepared using a simple equation: the product of area, bed thickness, density and recovery factors. Each of these elements involves a degree of risk based on certain assumptions. Reserve area, thickness and density rely on certain physical data whose accuracy, reliability and sufficiency may be problematical. Estimates of recovery factors for mining and coal preparation are often subjective. Most reserve estimates assume, sometimes incorrectly, that the subject reserves will be completely extracted. The principle that certain coal resources are reserves, if they can be considered economically recoverable at the time of determination, needs to be reexamined in the light of recent market cycles. Reserve estimating requires the exercise of judgments, the validity of which reflect the qualifications, experience and objectivity of the estimator.

Jan 1, 1985

By J. R. Mackie

Reserve Mining Company, the first large-scale taconite pellet producer in the United States, mines it's crude ore at the Peter Mitchell Mire located on the eastern end of the Mesabi Iron Range near Babbitt, MN. The ore is processed at Reserve's beneficiation plant on the north shore of lake Superior at Silver Bay, M. The mine and plant are linked by a 47 mile, double track, railroad which is owned and operated by Reserve. (see Fig 1). At rated capacity, the mine can produce 33 million It/yr of crude ore, 15 million It/yr of waste rock and 1.0 - 1.4 million yd3/yr of glacial till stripping. Haulage of all mined material is accomplished using trucks. Ore is transported by tractor-trailer side dump units which have capacitys ranging from 83 to 110 long tons. Waste rock and glacial till is transported in end dump units of 50 to 120 LT capacity. Loading is accomplished by 11/13 yd3 power shovels and 7/10 yd3 front-end loaders.

Jan 1, 1985

The present practices in electro-refining of copper are shown to be the result of piecemeal and gradual improvements and innovations as metallurgists responded to changing cost pressures and the availability of new technology.Major changes were inhibited by capital cost restraints and a reluctance to build unproven ideas into new plants.It is suggested that the level of technology available today, combined with the greatest cost pressures the industry has known, call for fundamental re-appraisal and a questioning of widely accepted conventional practices.Examples of the industry reaction to changing pressures are given, and directions for future developments are suggested.

Jan 1, 1985

By Paul S. Goodman

Volume I This report presents the first national survey of miners' attitudes and opinions about their-work. The goal is to present attitudinal data that bears on coal production. Interviews were conducted in 26 mines with 2,000 miners. High levels of cooperation were exhibited by management, union and the employees. Data are presented about miners' attitudes about general aspects of their work such as pay, supervision, their jobs, etc. Another section of this report reviews opinions about specific aspects of work performance. Recommendations are presented.

Jan 1, 1985

By L. G. Austin

My first contact with industrial milling was during the time I worked in the electricity generating industry in the United Kingdom. In visits to power stations to investigate either deposits in the boiler furnaces or polluting deposits settling around the stacks. I had to check the performance of the vertical coal pulverizers, since poor pulverization aggravated both problems. Naturally, then, when I came to the USA in 1957 to take a PhD in fuel technology at Penn State, I was put to work to review the science of coal pulverization. After this reviewing, I was completely confused. On one hand, there was a well-developed understanding of stress-strain equations, and a rapidly developing knowledge of how stressed, brittle solids fractured, based on the Grifith crack theory. On the other hand, reading in the grinding literature gave me: -Kick's Law, which was clearly not correct in the light of modem fracture theory; -Rittinger's Law, which was also clearly not correct; -Bond's Third Law of Comminution, which was claimed to have something to do with the Grifith crack theory, but where the connection between the two was made by intuitive pseudo-scientific reasoning I could not accept; -the choice of mill motor power for the most common type of coal mill, the Raymond pulverizer, was calculated from the fan power required to move air through the mill. Although I could accept the empirical connection between the two, it made no sense from the point of view of fracture energy. Even today, most books or review chapters on size reduction start from these laws. Incorrect statements abound in the literature, such as "the Hardgrove Index is based on Rittinger's Law," which it is not, "The Bond theory states that work input is proportional to new crack tip length produced in particle breakage," which is not true, etc. My own test work showed that these "laws" did not fit the data for grinding of coal. At about this time, Epstein (1948) and Broadbent and Callcott (1956), following the original work by R.L. Brown (1941) at the British Coal Utilization Research Association, proposed describing breakage as a series of fracture stages. I took their concepts and developed the basic differential equation for a batch grinding process continuous in time, analogous to a batch chemical reactor. Robin Gardner then joined the project and did his PhD on treating batch grinding in the same way as a batch chemical reactor. He found that the basic equation had already been partially derived by Sedlatschek and Bass (1953) in Ger- many. We confirmed experimentally the validity of the equations for describing batch grinding (1962) and formulated the equation describing steady-state continuous grinding in a fully-mixed mill. At about the time this work was published, Gaudin and Meloy (1962) and Filippov (1961) independently published essentially the same equations, but without experimental proof of the validity of the concepts. I will give a brief overview of what these beginnings had led to in the design of mills for size and power, and show some of the results of this more detailed understanding of grinding processes. Concepts of Fracture Mills such as tumbling ball, rod, pebble and autogenous mills and vertical mills such as the Raymond, and E-type, apply compressive stress to lumps or particles relatively slowly. Compressive stress applied to a particle of an elastic brittle solid imparts overall strain energy to the solid and produces local regions of tensile stress, [(Fig. 1)] (Berenbaum and Brodie, 1959).

Jan 1, 1985

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

Tests were carried out in a Hallimond microflotation cell and a Denver D12 cell on typical residue material from a gold mine in the Orange Free State (South Africa), in which 50 per cent of the kerogen was larger than 100 µm in size. Although kerogen is naturally hydrophobic, the observed unexpectedly poor flotation reponse may be due to occlusion of the kerogen by a slime coating and subsequent depression of the slime by guar gums. The recovery of gold from samples spiked with kerogen increased, with no significant reduction in grades, when a petroleum-based collector and tetrasodiumpyrophosphate (a dispersant) were used.

Jan 1, 1985

By R. S. Young

There can be very few members of the Institute who failed to appreciate this extremely interesting and informative paper by Mr Rohrmann of Highveld Steel and Vanadium Corporation. This story of vanadium in South Africa has a very wide appeal to members of our profession: it embraces both ferrous and non-ferrous metallurgy, and both hydrometallurgy and pyrometallurgy. In a comparatively short time, South Africa has become one of the the world's leading producers of vanadium.

Jan 1, 1985