Search Documents

By D. Erik Spiller

Introduction The recovery of precious metals from ore can generally be accomplished using either gravity concentration, flotation, and/or hydrometallurgical (leaching) techniques. The objective of this paper is to show why gravity concentration can be an important part of recovery systems which employ leaching as the primary unit operation. A brief discussion of modern gravity concentration equipment is also presented.

Jan 1, 1984

By H. Xi-Lum

Three rapid cold bonding production methods wing sponge iron powder as a binder for low temperature pellets have been successfully developed. These methods differ from ordinary bonding by the elimination of salt and other catalyzers, equipment corrosion and environmental pollution. Experiments show that these pellets have good metallurgical properties. A semi-industrial test has proven the laboratory results, with the continuous and stable production of metallic pellets. These methods replace traditional high temperature firing of oxidized pellets for direct reduction. As a result, the plant for oxidized pellets can be saved and substituted for grate in the grate-kiln system. Thus, 20% of the investment could be saved, and production cost may also be decreased because the production of cold bonding pellets does not need additional space.

Jan 1, 1984

By Nancy S. Brodsky

A specimen of Westerly granite was cyclically loaded to near failure at 50 MPa confining pressure. Holographic interferometry provided detailed measurements of localized surface deformations during loading and unloading. The data are consistent with deformation occurring primarily elastically at low differential stress; in conjunction with one incipient fault zone between approximately 350 and 520 MPa differential stress; and in conjunction with a second incipient fault zone above 580 MPa and/or during creep. During unloading only one fault zone, that which is active at the intermediate stress levels during loading, is seen to recede.

Jan 1, 1984

By Gordon E. Agar

"The effectiveness of two this compounds for copper sulphide depression in molybdenite flotation has been examined with batch bench scale tests.Both thioglycollate and trithiocarbonate proved to be good depressants producing results similar to those f or cyanide and hydrosulphide. Ferrocyanide was ineffective on the samplematerial tested.The depressing effect of thioglycollate was readily reversed by an addition of xanthate.IntroductionThe separation of molybdenite from copper sulphide minerals has been practised for a long time(1,2). The predominant scheme is to depress the copper sulphides while capitalizing on the ready floatability of molybdenite to effect the separation. There are many recipes for depressing the copper minerals(3), among them the addition of sodium cyanide, particularly if the copper is present primarily as chalcopyrite; some form of sulphide whether as sodium sulphide, sodium hydrosulphide or phosphorous pentasulphide when there is a mixture of copper sulphides such as bornite, chalcocite and chalcopyrite; potassium ferro cyanide may be used when chalcocite is the principal copper sulphide; peroxide or hypochlorite; as well as heating in the presence of lime. There are different mechanisms by which these reagent s depress the copper sulphides. Sodium cyanide and the sulphide-producing compounds apparently reduce the potential of the copper sulphides to the point where they ar e rendered unfloatable by xanthates . Another study(4) showed that after cyanide addition, chalcopyrite was rendered un floatabl e until the REDOX potential (measured with a gold electrode with a saturated calomel reference) had become more positive than -250 mY. If the chalcopyrite pulp was conditioned after the cyanide addition the REDOX potential increased slowly, whereas if air was introduced during the conditioning the potential r ose much more rapidly. The difference in time to reach the desired level of - 250 mV was as much as 20 minutes' 25 minutes being required when air was absent but less than 5 minutes when air was admitted . These observation s demonstrate some of the problems encountered when using cyanide to depress sulphides such as chalcopyrite . The system adjusts to counteract the depressing effect of the additive. To overcome this tendency it is necessary to either add an overdose at the beginning or to more or less continuously add the regulating reagent. In this study cyanide solution was added under automatic control to maintain a specified REDOX potential."

Jan 1, 1984

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By Khosrow Bakhtar

A series of nineteen shear tests were performed on fractures 1 m2 in area, generated in blocks of sandstone, granite, tuff, hydro- stone and concrete. The tests were conducted under quasi-static and dynamic loading conditions. A vertical stress assisted fracturing technique was developed to create the fractures through the large test blocks. Prior to testing, the fractured surface of each block was characterized using the Barton JRC-JCS concept. The results of characterization were used to generate the peak strength envelope for each fractured surface. Attempts were made to model the stress path based on the classical transformation equations which assumes a theoretical plane, elastic isotropic properties, and therefore no slip. However, this approach gave rise to a stress path passing above the strength envelope which is clearly unacceptable. The results of the experimental investigations indicated that actual stress path is affected by the dilatancy due to fracture roughness, as well as by the side friction imposed by the boundary conditions. By introducing the corrections due to the dilation and boundary conditions into the stress transformation equation, the fully corrected stress paths for predicting the strength of fractured blocks were obtained.

Jan 1, 1984

By Larry D. Hartzog

PANELISTS Paul Chamberlin, Nerco Minerals Jim Gourdie, Goldfield Mining Corp. Roger Leonard, Cyprus Northumberland Mining Co. Eric Daniels, Tenneco Minerals John Dasher, Consulting Metallurgist Bob Shoemaker, San Francisco Mining Associates Larry Hartzog, Bechtel Civil and Minerals, Inc.

Jan 1, 1984

By Muir DM, Tsuchida N, Dalton R

The adsorption or loading of anions onto extruded based peat activated charcoal has been studied by potential measurements in a flow through cell. Loading rates are in the order F-

Jan 1, 1984

By Georges Verly

The estimation of local recoveries is an important issue in a selective mining operation. Two techniques, probability kriging and multigaussian kriging, are applied to estimate local recoveries at Jerritt Canyon. The pros and cons of each method are discussed in light of the results. Both methods provide simple and satisfactory solutions to the problem of estimating local recoveries. Consequently, they can be useful tools to work with in a selective mining operation.

Jan 1, 1984

A novel problem-solving exercise for undergraduates is described which is directly relevant to production supervision. It is based on the fictitious Metwin Plant which produces refined metal from sulphide concentrates via a hydrometallurgical route with six unit operat- ions. Students are given details of the chemistry, process engineering and normal operating conditions. They are also given min- imum data for the Plant when it is operating with a fault. By requesting further data, for which they are 'charged', the students must diagnose the fault. The responses of students to the exercise are described. The data were produced by computer simul- ation of steady state operation under normal and various faulty conditions. The development of this program was an educational experience for the author and it stimulated new interest in metallurgical process engineering.

Jan 1, 1984

By William K. Callaway

Cominco American has operated the Magmont Mine for 16 years as a traditional open stope room and pillar mine. Diminishing ore reserves and the discovery of high grade ore zones over 90' in thickness caused consideration to be given to hydraulic sandfilling as a method of ground support to increase pillar extraction and mine life. This paper will review the results of sandfill testing. Plans for underground experiments, and operational plans for the future will also be discussed.

Jan 1, 1984

By J. A. Rajala, R. W. Smith

The effect of increasing ionic strength, via monovalent and divalent ions, on alkyl sulfate flotation of hematite and quartz war investigated. The effects of collector chain length and pretreatment on this flotation were also studied. Sodium hexadecyl sulfate was shown to be a superior flotation collector to sodium dodecyl sulfate for recovery of hematite when there was no salt addition. Similar observation were made when sodium sulfate or sodium chloride was used to control ionic strength. Sodium dodecyl sulfate floated hematite better than its longer chutited counterpart under conditions of low pretreatment temperature and increasing calcium chloride concentration. The flotation recovery for all salt containing pulps was almost always improved after preboiling. Most of the results obtained when the pretreatment temperature was raised were attributed to increased solubility of the collector.

Jan 1, 1984

By C. T. Sheeran

The Bureau of Mines investigated a microprocessor-based real-time control and monitoring system for uranium mining applications. The system is capable of controlling and monitoring up to 768 stations within 3 km of the central processor on a common four-wire cable. It can be used in conjunction with detectors to continuously monitor and display radiation working levels at points throughout the mine. Surface alarms are sounded for critical situations such as rapid radiation buildup, loss of power to monitors or fans, and changes in air door position. Permanent records of all changes are automatically printed out with their time of occurrence. Printouts can also be obtained for shift reports or trend logs. The system can be used to remotely control fan startup and shut-down, and also can alert miners of underground conditions by blowing horns or turning on lights. Battery backup keeps the system operative for up to 4 h in case of a mine power outage. A special software feature permits automatic, time-delayed, sequential restart of fans.

Jan 1, 1984

Alluvial gold exploration is aimed at recognizing areas of anomalous gold content as evidenced by the nature of the drainage system, its age, geomorphic history and other features of the geological environment including the provenances. Subsequent studies to quantify the findings are governed by the need for accurate data based upon precise measurements. Computerization allows the use of more complicated mathematical procedures than are feasible manually, thus promoting the development of more advanced technological aids. Data banks provide the means of storing vast quantities of information for instant recall.Sample representivity is a major problem and a clear understanding of both sampling and analytical requirements is essential for dealing with problems arising from variations in sample size and particle size distribution. Field samples must always be large enough to ensure adequate representivity or the sampling has failed in its purpose.

Jan 1, 1984

By Russell L. Wood

The title of this session seems to have been picked especially for this paper. It is 1984, it is the morning after, and there is one monumental hangover among many if not most of the oil companies that have invested in mining in the past decade or so. How an oil company looks at mining depends on what time period you are talking about. A few years back around the time of investment this is what they were probably looking at: 1. A balance sheet of their own that was beginning to go wild, with many of their commodity prices having already seen increases of two, three, or four fold, and with no end in sight. 2. A need to invest their earnings someplace fast before the stockholders or the government got too interested. And that someplace should be in an industry where their own management skills could be applied. (Only a true cynic would suggest that this is a form of job security) 3. In mining there was an industry amazingly similiar to their own, one working with non-renewable natural resources, dealing with the same types of government agencies, and having the same type of critics and pressures from the general population. 4. An industry that was somewhat backward as compared with their own, and one where a generous ration of the capital and management skills so handsomely bestowed upon the oil industry could be used to great advantage.

Jan 1, 1984

By J. C. Marquardt L., J. A. Bratt, J. P. Hunt

The Quebrada Blanca copper/molybdenum prospect lies on a dissected plateau in the high Andes of Northern Chile. The Superior Oil-Falconbridge Group began exploration of the Property in 1977 under a joint venture foreign investment agreement with the Chilean government. Quebrada Blanca is a relatively high grade secondarily enriched porphry copper deposit. Primary mineralization occurred 38 million years ago and accompanied quartz monzonite intrusive. Early disseminated Primary mineralization was followed by hydrothermal mineralization, mineralized breccia, and post-mineral faulting. After supergene enrichment Quebrada Blanca was buried under late Tertiary gravels and then partially re-exposed in Quaternary time. During the past five years, a successful exploration program has developed an open-pit mining reserve, provided samples for bulk metallurgical testing, and located more than adequate supplies of water for future operations. The main orebody is amenable to conventional metallurgical treatment and contains more than 400 Mt (441 million st) of recoverable open-pit ore at about a 1:1 overall stripping ratio. The average millhead grade during the first six years of operations will exceed 1.5% Cu, plus recoverable molybdenum values. Several hundred million tons of additional reserves are available in the surrounding districts

Jan 1, 1984

By Dale S. Preece

In 1975 Congress passed the Energy Conservation Act to establish a U. S. Strategic Petroleum Reserve (SPR) with a capacity of 750 million barrels of crude oil. The most economic storage medium was determined to be salt caverns leached in salt domes in Louisiana and Texas. Salt caverns existed at several sites when the reserve was created. These were obtained by the U. S. Department of Energy (DOE) and used to initiate SPR oil storage. In order to meet the storage capacity approved by Congress, new caverns also had to be leached. To support the resulting design effort, finite element computer program have been used to determine the creep closure and structural stability of salt caverns. Using site specific material properties including creep models, elastic moduli and fracture data, the finite element analyses have replaced earlier empirical approaches to cavern design. This report presents results of such finite element analyses to determine the best cavern roof shape and the minium pillar to dimeter ratio. , P/D. These numerical predictions indicate that the current cavern design is safe.

Jan 1, 1984

By Don L. Deardorff

The Deserado Mine and transportation system is the fuel supply portion of the Bonanza Power Plant project. Deserado Mine con¬sists of an underground mine with a capacity of 1,224,700 tonnes (1,350,000 tons) of clean coal per year, a 649 tonne (715 tons) per hour closed water circuit jig type preparation plant, a 5.6-kilometer (3 ½ -mile) overland conveyor with covered slot storage, a unit train rail load-out and 59.5 kilometers (37 miles) of totally independ¬ent, captive electrified railroad. Planning and exploration started in March of 1978. Construction of all facilities was completed in April of 1984, approximately six years after initial planning was commenced. This paper will discuss exploration, environmental permitting, mine planning, engineering and construction of the Deserado Mine project.

Jan 1, 1984

The Rum Jungle mine was operated by Territory Enterprises Pty Ltd who mined uranium on behalf of the Australian Government with operations spanning the period from 1953 to the final closure of the mine in 1971. In addition to the extraction of uranium from the open cut pits, copper, manganese and lead were mined and processed at Rum Jungle. During the latter part of the operation, and after the closure of the mine, environmental studies were carried out which were aimed at determining the causes of the pollution at Rum Jungle and identifying a rehabilitation strategy for the mine site. These studies identified sources of heavy metal and acid pollution and proposed a rehabilitation strategy which consisted of 1. recontour, construct impervious covers and controlled surface drainage on, and revegetate three overburden heaps,

Jan 1, 1984