Search Documents

By Bruce Haldeman

Timber has been used as pile support for structures for 6,000 years. Some means of preservation of wood go back almost that far. Timber piles support all types of structures ? some are buried below the water table; others raise a home for protection from animals or a chief's home for prestige. Millions of wood piles have been driven for bridge support. Earlier piles were driven by hand then by ingeniously raised weights. Charring, animal fats and oils have been used for preservation. Coal tar creosote and other preservative methods started only in the early 1800's and give effective protection.

Jan 1, 1984

By B W. Riddol1s

The 1983 Energy Plan calls for an increase in North Island coal production from both underground and opencast sources from the 1982/1983 production of 843 000 tpa to approximately 3.4 Mtpa within the ten year period to March 1993. This increased production is scheduled to come from the following sources: Huntly West No 1 underground mine reaching full production of 1.26 Mtpa. Huntly East underground mine increasing production to 750 000 tpa. The proposed new Huntly West No 2 mine producing 100 000 tpa in its first year of operation û 1992. The proposed Ohinewai opencast producing 920 000 tpa for supply to the steelmaking plant at Glenbrook, replacing Weavers opencast which will be worked out in 1990. Rotowaro opencast producing at 220 000 tpa (currently being achieved). Two additional sources of supply which are not scheduled to begin production for at least ten years, and both of which have been designated for coal fired thermal power generation, are the Maramarua and Mokau coalfields. It was originally envisaged that development of both coalfields would be a combination of underground and opencast mines. The form of development is yet to be confirmed by detailed feasibility studies. The location of the Maramarua, Ohinewai (Waikare Coalfield) and Mokau deposits is shown on Figure 1. Worley Consultants Limited, in conjunction with their partners Rheinbraun Consulting GmbH (Germany) and Longworth McKenzie Pty Limited (Australia) have been involved with investigations and mining assessments for the Maramarua, Mokau and Ohinewai prospects. The Maramarua and Mokau studies form part of the New Zealand Coal Resources Survey programme of updating information to the Pre-Feasibility Mining Assessment level before proceeding to detailed feasibility studies. The Ohinewai study was commissioned directly by Mines Division to investigate the feasibility of mining coal by 1989 before reserves at Weavers opencast are depleted. This paper describes typical studies which are now being commissioned by Mines Division to investigate large-scale mining development and the effect geotechnical-conditions may have on coal recovery. The magnitude of these projects is reflected in the proposed outputs û up to2 Mtpa from individual mines û and the introduction of new continuous mining systems for both underground and opencast mines on a scale which has not previously been contemplated.

Jan 1, 1984

Develop quieted, hand-held pneumatic percussion drills that can replace standard hand-held drills in many underground mining applications. The Problem Percussion drills are the noisiest machines used in underground mines; noise levels of 115 to 120 dBA are common, requiring the use of hearing protectors and limiting the time a miner is permit-ted to operate the drill during an 8-hour shift. Hand-held pneumatic percussion drills pose a particularly difficult problem because the operator cannot be isolated from the noise source (e.g., an acoustical cab), and alternative technologies for drilling roof bolt holes and blastholes in tight quarters are not readily available.

Jan 1, 1984

By Jeffrey W. Nelson

Predictions of creep closure for periods ranging up to more than 1,000 years are needed for designing a radioactive waste repository in a salt formation. Such long-term predictions must be based on the use of laboratory and field test results extrapolated by numerical modeling. Laboratory test results are presented which show highly variable creep behavior for salts from different sites as well as salts from the same site. Comparisons of measured creep closures against predicted closures are presented for two deep boreholes in Louisiana salt domes and for an exploratory shaft and drift in southeastern New Mexico bedded salt (WIPP). These data illustrate the significant uncertainties involved in long-term closure predictions and indicate the critical need for site-specific, in situ closure measurements over extended periods of time for repository design.

Jan 1, 1984

By Lawrence PR, Hoffman W

The dissolution of gold from various ore-bodies is discussed in terms of extraction rates and reagent consumptions during leaching. Gold dissolves slowly in cyanide but reagent consumptions are usually satisfactory. In almost all cases where excessive cyanide consumptions occur, similar high consumptions result with other lixiviants. Recovery of gold from cyanide solution is well established and comparatively simple technology.Gold dissolution in thiourea is faster than cyanide but significant consumptions of thiourea, due to both adsorption and oxidation, occur. Gold recovery from thiourea solutions is likely to be more difficult than from cyanide.Chlorination of gold is very fast in acidic conditions but excessive consumption of chlorine occurs for ores containing greater than 0.5% S. Reprecipitation of gold and handling of acidic chlorine solutions are both significant problems. The mechanism of gold reduction onto activated carbon creates difficulties in the carbon in pulp process for recovery of gold but means a simplification in the production of bullion from loaded carbon.

Jan 1, 1984

By David T. Couillard

Task training is increasingly important in mining operations because of the ever-accelerating pace of technological innovations and the concomitant increasing complexity of mining equipment. This Bureau of Mines report describes two successful task training program In use in two open-pit taconite operations in northeastern Minnesota. The programs are different in approach, but both have improved safety and in- creased productivity while lowering costs. Methods of training both before and after passage of the 1977 Mine Safety and Health Act are described, and the impact of this act on task training at each operation is discussed. The report identifies four common principles that have contributed to the success of the two training programs and presents plans each operation has for improving future training through new technology.

Jan 1, 1984

Coal has become an enormously important export industry. Owing to a range of mainly natural advantages, Australia has been able to almost treble its exports in a little over the last decade. Australia is now the world's second largest exporter and coal is now the nation's largest single export earner.Despite this very significant growth, Australia's competitive position is in jeopardy.

Jan 1, 1984

By David Branch, Martin J. White, Faramarz P. Hassani

The work presented in this paper is part of an overall research programme into the problem of stability of main access roadways driven in Coal Measure strata. Data about the post-failure behaviour of rocks are generally of a qualitative rather than quantitative nature. This investigation represents the initial part of a long-term research project aimed at quantifying the post-failure properties of Coal Measure rocks and to investigate their effects on tunnel stability. The results of tests conducted to evaluate the post-failure strength characteristics of Coal Measure rocks under uniaxial and triaxial stress conditions are presented. Empirical failure models are proposed to define the triaxial intact and residual failure properties of these rock types. The application of such data to closure prediction techniques of underground excavations are outlined and discussed.

Jan 1, 1984

My roots span four generations. My great grandfather, Christian Frederick Fisher, along with twenty-one others was drowned in the New Australasian mine disaster at Creswick in Victoria in 1882. My grandfather, also named Christian Frederick Fisher, escaped and then followed a career of shaft sinking for large companies and operating small mines (very unprofitably according to my father) when funds allowed. My father, an excellent practical mining and mechanical engineer, was also a small miner and my early entry into the industry was, like many before me, very basic. My introductions to the business end of a No. 4 shovel, drilling with hand steel and later with jack hammers without the benefit of airlegs, feeding heavy cordwood to hungry boilers and felling trees for mine timber soon dispelled any illusions I had that mining was a bed of roses.Before it became well known I knew "Life was not meant to be easy".In a family-owned small gold mine in a remote part of Cape York Peninsula in far north Queensland I was fortunate in obtaining an excellent grounding in reef and deep alluvial mining. Operating in vertical and underlie shafts the variable ground conditions often required close timbering. Steam pumps were used underground and steam winders for hoisting.The complete absence of municipal or government infrastructure in this remote mining field threw responsibility on each mine operator to be self-sufficient, and responsible for mine development and installation of crushing and milling equipment, accommodation and water supply. Conditions, although harsh, were acceptable in the 1930s, and fostered great self-reliance.The first crushing from our Black Cat Mine in 1935 returned nearly 200 oz from 10 tons of ore. Gold was then worth $13 an ounce compared to about $400 an ounce today; but in those depression years of the 1930s our operation was profitable.This basic education not only returned dividends when confronted with difficult mining problems, but created a deep respect for the miners who develop the small mines and who continue to contribute to the industry today, often under difficult conditions.Australia and mining are synonymous. The industry has been immortalised by the famous historian, Professor Geoffrey Blainey, in his book "The Rush that Never Ended".Initial gold discoveries were concealed and exploration was frowned upon by authority as being disruptive to early rural development. But with the discovery of gold in the Bathurst area of New South Wales by Hargreaves in 1851, the rush to the gold fields began followed by an influx of migrants. The traumatic effect on industry and society that followed, created the pattern of the love-hate relationship that at times became temporarily submerged, but is so evident today.In the harsh economic climate of the 19th century with low wages and no welfare, the opportunity to wrest riches from the earth was literally "rushed" by the adventurous, the poor, the rich, people from all walks of life. Pressures developed on preFederation Governments to provide law, order and infrastructure to the rushes that have never ended.

Jan 1, 1984

By R. C. Corson

Modern microprocessor systems make it possible to use several variables to anticipate changes in the process and to react with responses before upsets can be magnified by the process or by control action. Through tighter control, "insurance" can be eliminated from process set points without affecting product quality. In actual operation with a traveling grate furnace this control philosophy has produced savings of up to 20% in fuel consumption and 8% in fan power usage while producing a more consistent quality product.

Jan 1, 1984

There are many variables in a flotation concentrator, some of which are outside the actual flotation stage, which affect metallurgical performance. The number of such variables which can now be measured on a continuous basis has increased significantly over the past 20 years. They can be broadly classified under the headings of physical, chemical, and elemental. In this paper reference is made to a number of such variables, and comment is made on the state of the art in their measurement. Although not confined to development in Australia, particular reference is made to the considerable Australian contribution in this area of Technology.

Jan 1, 1984

By Lawrence R. Artler

The North American Coal Corporation, its subsidiaries and other coal companies, have been mining the Pittsburgh #8 seam in Eastern Ohio for several decades. Underground mining by the "room and pillar" method, and more recently by longwall methods, have been practiced. This presentation deals with ground control problems and subsequent solutions to those problems for both mining methods. But first, let me briefly discuss some pertinent points about the geologic conditions of the coal seam near the southwest edge of the Pittsburgh Coal Basin. The Eastern Ohio region of the Pittsburgh Coal Basin is situated along the western edge of the unglaciated Allegheny Plateau. The local terrain is quite steep, with topographic relief of 430-500 feet being common. The coal thickness in the region ranges from 36"to 120", with the average being 60" in the areas being currently mined. Regional dip of the seam is toward the southeast in an amount of 10 to 40 feet per mile. A cross-section of the mineable seam generally consists of the main bench (60"), a rider coal (6"-12"), and a claystone parting (6"-12") for a total excavated height of 6-7 feet. Greater excavated height occurs where the fireclay floor is so soft and friable that movement of mechanical equipment breaks up the first 4-8 inches. Generally, the main bench and rider coal thin and become more variable toward the southwestern portion of the mining area. The rider coal also grades laterally into a coaly carbonaceous shale. In those areas where the roof coal can no longer be counted on to help support the immediate top, some of the main seam (6") is left to protect the overlying 8'-12' of mudstone/claystone strata. These strata are virtually non-bedded, highly slickensided units and are "hung in suspension" by roof bolts from a more competent limestone stratum above. These mudstone/claystone units are very susceptible to moisture and thus to the weathering cycles. The rider coal or 6" of the main bench is left in place to "seal" the mudstone/claystone units in Mains and Submains development. For many years, it was thought that the strength of the limestone member was detrimental in attempts to fully extract the seam by conventional means; however, longwall methods that have been more recently employed have broken the "myth" that the Redstone Limestone prevents full extraction of pillars.

Jan 1, 1984

By S. K. Kawatra

In this paper three methods of on-stream analysis 1) Radiometric techniques, 2) X-ray tube techniques and 3) Neutron activation method are reviewed. Advantages and disadvantages of each method are discussed.

Jan 1, 1984

By J. C. Lee

This investigation considers the penetration of a crack through an interfacial boundary separating two materials. The interface is assumed to be an imperfect bond characterized by frictional resistance and the cracks are assumed to be pressurized. The formulation is achieved through the use of complex variable methods together with the application of dislocation solutions. Results are given in the form of dimensionless variables that represent the injection of an incompressible liquid.

Jan 1, 1984

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984

By R. H. Church, William E. Webb, Walter E. Pittman, James R. Boyle

As part of the Bureau of Mines health and safety research program, a short-range locator system, capable of locating miners who have become trapped following a mine accident, has been devised, The system consists of a lightweight, low-power radio transmitter incorporated into a miner's cap lamp battery and a directional receiver carried by rescuers. Prototype transmitters have been constructed, and the propagation of their signals has been investigated, The detectability of the signal in underground coal mines has also been investigated, This research indicates that a short-range location system would serve as an economical and practical means of locating miners from within the mine following an accident,

Jan 1, 1984

By N. D. Policow, J. S. Orphanos

Dewatering fine clean coal fractions, -595µm (-28 mesh), represents one of the most difficult and costly separations in typical plant circuits. Since 1969, the screen bowl centrifuge has offered an economical alternative to filtration/thermal dyer combinations. The performance of screen bowl centrifuges has been continuously modified and improved to dewater not only coarser coals, but also today's variety of ultrafine material. Test comparisons with alternative methods show the screen bowl centrifuge to be most cost effective and efficient when all factors are considered.

Jan 1, 1984

By R. D. MacEchern, M. C. Rockwell

"This paper describes the research and tests carried out to recover the readily available barite from the tailings produced by the Nystone Chemical Ltd. operation at Debert, N.S. The tailings comprised 70-80% of the original feed and contained about 20-25% Baso4 .The objective of the research, undertaken during 1982, was to produce a barite concentrate which would meet the American Petroleum Institute (API) barite requirements for use in drilling mud. Samples from the tailings pond were examined and analysed to determine the tailings characteristics.Preliminary test work was performed on the tailings samples using a Haultain Superpanner, Wilfley tables and Humphrey's spirals. The grade of the barite concentrate retrieved did not satisfy the API barite requirements.The fineness of the tailings and the fact that approximately 80% of the barite was contained in the -200 mesh (0.074 mm) size fractions, indicated that flotation of barite from the tailings might be successful."

Jan 1, 1984

By James S. Grichar

Interest in mergers in the nonfuel mineral industry developed when 5 were listed among the 50 highest valued mergers in the United States in 1981. This report presents a Bureau of Mines study of trends in merger activity from 1960 to 1979 and explores motives for mergers in the nonfuel mining and mineral industry. The objective was to determine precedent for or a trend toward the 1981 acceleration in merger activity and to examine certain financial motives for non fuel mineral mergers. Data indicate that the relative value of non fuel mineral mergers has grown since 1972 although the number of mergers has remained proportionate to historical trends for all mergers. Since 1974, the assets acquired in "large," nonfuel mineral firm mergers, those of $10 million or more, have comprised at least 93 pct of assets acquired. More nonfuel mineral firm mergers involved mineral companies as the acquiring firm than vice versa but mining and minerals firms acquired were of higher value than nonmining firms. A major motivation for mergers involving large mineral firms was the acquisition of assets at less than replacement costs. Univariate statistical testing, a methodology chosen for its applicability to the data, confirms this hypothesis while rejecting other financial motives. The remainder of the work is devoted to a discussion of suggested areas for future study.

Jan 1, 1984

By S. N. Dixon

Sampling and assaying procedures were developed to obtain unbiased and reasonably accurate Au grade estimates in drill samples fm a coarse gold deposit. Gold grade comparisons were made by assaying 3 (1 assay ton) splits from each drill interval, then processing the entire reject thru a pilot plant for a blocked out zone. The result comparing the assay splits to the pilot plant results gave a ratio of 1 to 1.07. Another technique was developed to detect drill samples which has a coarse gold content by monitoring the varience. Testwork could be done on a 1 kg sample to improve the accuracy of the grade estimation if the variance was high for a drill interval.

Jan 1, 1984