Search Documents

By R. V. Ramani

This report, Volume I of the seven-volume Final Report on the U. S. Bureau of Mines research contract no. G0254030 titled Application of a Total System Surface Mine Simulator to Coal Stripping with the Pennsylvania State University provides an executive summary of the purpose and scope, objectives and results of the research. The remaining volumes of the Final Report, listed below, describe in detail model development, input and output documentation and the three case studies. Under the project, an existing surface mine simulator, Open-pit Materials Handling Simulator (OPMHS) was modified and extended for application to surf ace coal mining. In addition, two equipment selection models, and a cost model were also developed. Volume II: OPMHS User's Manual Volume III: Equipment Selection Models Volume IV: Surface Mining Cost Model Volume V: Application of OPMHS to an Illinois Mine Volume VI: Application of OPMHS to a South Eastern Ohio Mine. Volume VIII: Application of OPMHS to a South Western Mine.

Jan 1, 1978

In any strip coal mining operation the aosL important single operating unit is the dragline. Because the capital and operating costs of a dragline are high, it is desirable to operate these machines at their maximum efficiency. Thiess Bros. Pty. Limited operate a Bucyrus-Erie 1350 Walking dragline at their Callide coal mine. The operating conditions at the Callide Mine are different from those of other coal mines situated in Central Queens ,nd. The topography is rugged, the coal seam is thick, and the overburden is hard and inter- HH,inded. Several different operating techniques for a large dragline working under these con- ditinns arc discrossmd it tt

Jan 1, 1978

By Douglas M. Dwosh

Inland Steel Coal Co.'s system of applying a gypsum/fiberglass rib and roof sealant with standard rock dusting equipment will be outlined. The criteria for use included acceptability of results, flexibility of equipment, ease of application, and economics. Material is conveyed dry until the gypsum, fiberglass, and water are combined at the discharge end of the rock dust hose.

Jan 1, 1978

By Lars A. Bergstrom

High-voltage direct -current transmission is a relatively new technology. The successful development and operation of AC/DC converters, capable of handling large power blocks, have made HVDC transmission generally accepted by utility engineer s and planners around the world. HVDC technology still has significant development potential and, as a result, it is expected that equipment costs will escalate at a substantially slower rate than those of conventional AC equipment. This development will also result in still more compact terminal stations. This paper reviews two modern HVDC installations. In Zaire in Africa. a 1700-km overhead DC line rated at 500 kv, will supply power to the copper mining district in the Shaba region. Another HVDC link connects Norway and Denmark through a submarine cable rated at 250 kv. This is the longest HVDC cable in the world, 127 km, and the water depth , maximum 530 m, is also much greater than for any previous similar cable. The reasons for selecting HVDC are discussed, and the design and layouts are presented.

Jan 1, 1978

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By John L. Stafford

The ROEMMC combustion system was originally conceived as a means of utilizing solid fuels that would otherwise have been wastes requiring disposal and convert these fuels into useful energy sources. This concept follows as an extension of the application of residual waste incineration with energy recovery practiced in the lumber, manufactured board, sugar cane, and other industries. The incineration of these wastes in the furnaces of steam generating equipment is thoroughly described (1, 2, 3, 4, 5, 6, 7). The fundamental principle of the ROEMMC system is temperature control which makes possible the maintenance of the non-combustible fraction of these solid fuels in a dry solid state and their separation from the gaseous products of combustion. This philosophy of ash removal and the "slagging" philosophy are compared. The ROEMMC equipment function and applications are described.

Jan 1, 1978

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases attend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1978

INTRODUCTION This chapter summarizes characteristics of porphyry copper deposits within the Cordilleran orogen east of the Coast Range plutonic complex of the Yukon and British Columbia and south to the Columbia River plateau and the Idaho batholith. Porphyry copper deposits in this area reflect a geologic environment different from that found for mineralized intrusions elsewhere in the Cordilleran orogen, both to the south in the United States and Mexico and to the west in Alaska. A section on the Tertiary Cascade porphyry copper province is included herein. The Cascade province is considered separately because its deposits display a unique mineralogy and age of mineralization. That portion of the Cordilleran orogen described in this chapter is shown in Fig. 32, with the Cascades shown in Fig. 39 (see p. 114). The regional geology of this area has been described by Monger, et al. (1972), Hollister (1974), Wolfhard and Ney (1974), Field, et al. (1974), and Stacey (1974). Each offer slightly differing views on the post-Mississippian evolution of the geology in this porphyry copper province. The descriptive geology in this chapter has benefited from many discussions with J. E. Armstrong and J. W. H. Monger. Two separate petrologic models have been used popularly to categorize porphyry copper deposits in this area, a diorite and a quartz monzonite model. The diorite model, which involves a mineralized quartz-free pluton, has also been called the alkalic type (CZM Special Volume 15, 1976, and Soregaroli, 1975) and the syenite suite (Sutherland Brown, et al., 1971). The quartz monzonite model has also been named the calcalkalic type (CZM Special Volume 15, 1976) and includes mineralized quartz-bearing plutons compositionally ranging from quartz diorite to granite, with the igneous phase closest to ore in time and space commonly being quartz monzonite.

Jan 1, 1978

To monitor the quantity and quality of air in underground mines to assure safe working conditions. Approach Several mine air monitoring systems, consisting of sensing stations in the return airways and control stations on the surface, have been Installed and tested. How It Works Sensor stations are located at strategic places in the underground mine. At each station, the sensors measure air velocity, air temperature, methane concentration, and carbon monoxide concentration. In one system, differential air pressure between intake air and return air, is also measured. Output voltages of the sensors are converted to digital signals at the sensor stat ion; these signals are multiplexed so that data from all sensors can be trans-phone wire to a central station. There the data are displayed and alarms are triggered when the sensed values exceed (or in the case of air velocity, fall below) a preset value. In addition to receiving data automatically, the central station can poll individual sensors at any time.

Jan 1, 1978

By Alan Bauer

New developments in drilling, blasting and explosives in both open-pit and underground mining operations are discussed, as well as novel surface blasting techniques such as are used in tar sand mining.

Jan 1, 1978

By D. C. Myntti

An open pit mining equipment maintenance program, in order to be successful, must have many active segments covering the full range of equipment selection, trained personnel, repair facilities, preventive maintenance programs, warehousing, interdepartmental cooperation, paperwork and effective communications. The mine maintenance program is required to protect company assets Which are units of equipment generating revenue. The program should result in reduced unscheduled equipment downtime, increased equipment productivity rates, and decreased unit operating costs. Current maintenance problems; maintenance effectiveness and future projections on equipment maintenance are discussed. Equipment maintenance is big business and the maintenance department is a full-time partner in the mining venture.

Jan 1, 1978

By Nicol S. K, Swanson A. R

The poor flotation response of many coals has in the past been attributed to such factors as differences in rank, differences in degree of oxidation, differences in petrographic composition, or slime coatings. The present work shows that while all these factors undoubtedly influence flotation, the size distribution of the feed may override these. Evidence is presented which shows how this factor can lead to substantial losses of coarse coal (>250 µm)from a coal which would normally be considered amenable to flotation. Reasons for this loss of flotation response are suggested together with means of overcoming the problem.

Jan 1, 1978

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By Harold B. Treweek

The development of full scale flotation circuits based on laboratory and/or pilot plant data is discussed. Auxilliary operations, equipment and layout essential for trouble-free start-up and operation are noted. The selection of flotation cell size is discussed as it affects plant capital and operation costs.

Jan 1, 1978

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By Jon E. Fatzinger

The design of a centrifugal slurry pump is approached as a compromise between efficiency and wear life of the wetted parts. This compromise is effected by the choice of proper materials of construction and geometry. However even the most optimally designed pump will fail if due consideration is not given to its installation and operation. System head curves and hydraulic profiles are discussed as useful tools to be used in the operational analysis of a slurry system.

Jan 1, 1978

The Climax Molybdenum Company' s newest operation is the Henderson project, which is located on the east side of the Continental Divide. Ore reserves are estimated at more than 300 million tons at a grade of 0.49% MoS2. For mining the ore a modified panel caving system is used. The ore is transported to the Henderson mill on the west side of the Continental Divide on a 42 in. (1.07 m) gauge railroad through 9.6 miles (15.4 km) of tunnel and 4. 8 miles (7.7 km) of surface track, a total distance of 14.4 miles (23. 2 km). Each train consists of 30 ore cars with capacity of 22 st (20 mt) of ore or 660 st (599 mt) per train. The unmanned trains operate completely automatically. At the 54 in. by 84 in. primary gyratory crusher, the bottom dump ore cars pass over a dump scroll to discharge at a maximum rate of 100 st (91 mt) per minute. Dumped ore falls onto a rock box before passing over a 17 ft long by 46 ft wide (5. 2 m by 14 m) grizzly set at a 40° angle with bar spacings of 7 ½ and 8 ½ in. (191 mm and 216 mm) openings. An estimated 30 to 50% of the ore (which at times is wet and sticky) passes through the grizzly. The operators report that a shallower angle on the grizzly, perhaps 35º to 37º, would have been sufficient and would have prevented impact on the back of the crusher pocket by large boulders. This pocket as well as the crushed ore pocket under the crusher is lined with AR plate. The accompanying drawings show a "future splitter" and the operators are planning the installation of this unit to prevent impact and subsequent damage to the crusher spider. Crushed ore at an 8 to 9 in. (203 mm to 229 mm) size joins the grizzly undersize in the pocket beneath the crusher. This pocket is sized at 660 live st (599 mt) so that it will accept an entire trainload of ore. Crushed ore is removed from the pocket by a four-speed, 84 in. (2. 1 m) apron feeder operating at 9.6 to 29. 3 fpm (2.9 to 8.9 mpm). A 60 in. (1.5 m) takeaway conveyor operating at 480 fpm (146 mpm) delivers the crushed ore to a 58,000 st live and 193,000 st total (52,600 and 175, 100 mt) open stockpile under an A -frame supported tripper gallery. Impact idlers on the takeaway conveyor under the apron feeder discharge are mounted on wood blocks for a cushioning effect and ripped belt detecting bars are located behind each impact idler. The conveyor tunnel is of corrugated and galvanized steel construction rather than concrete. The concrete crusher enclosure is circular in design from its lowest level at elevation minus 110 ft 4 in. (minus 33. 6 m) to elevation

Jan 1, 1978

By Wi11iam M. Leaders

Uranium Recovery Corporation was incorporated in the State of Florida in 1968 for the sole purpose of developing a method to economically recover uranium from Florida phosphoric acid. The preliminary laboratory work culminated in the demonstration of the process to United Nuclear Corporation in the spring of 1971. This was quickly followed by a pilot plant program to identify any unusual problems such as those arising from the day-to-day variation which occurs in a fertilizer phosphoric acid plant production system. After two years of pilot plant operation, United Nuclear Corporation purchased controlling interest in Uranium Recovery Corporation and committed several million dollars to the design and construction of the first commercial plant for this purpose in the State of Florida, or anywhere else in the United States, for that matter. After many start-up problems were resolved at the production plant located at the W. R. Grace fertilizer complex near Bartow, sustained production began March, 1971, and has continued to date. We still have some problems to solve but are currently producing sufficient uranium to make shipments to the UF6 converters for preparation of Florida uranium for use in nuclear power plant fuel materials.

Jan 1, 1978

By William A. Kneller

Fifteen samples of chert from seven localities in Ohio were tested for potential durability and reactivity in concrete. The tests determined are porosity, pore-size distribution, relative degree crystallinity, specific surface area, and degree of dissolution according to the ASTM C289-71, Potential Reactivity of Aggregates, Chemical Methods. The results of these tests were compared with petrographic, electron optical, physical-chemical, and engineering properties of the chert samples. Based on these tests, the important properties that affect the durability and reactivity of chert in concrete were observed to be: (1) porosity, (2) pore-size distribution or pore spectra, (3) relative degree of crystallinity, (4) grain size, (5) specific surface area, (6) impurities, and (7) amount and species of quartz present-all of which are functions of original composition, time (geologic age), depth of burial, tectonics, and diagenesis. Preliminary results of this study indicated that the geologic history and physical-chemical properties of chert vary from one sample to another, and any one or combination of these parameters affect the performance of the chert in concrete. These complex interrelationships are difficult to ascertain; if the performance of the chert in concrete is to be predicted, it is necessary to study in detail this enigmatic material.

Jan 1, 1978

By R. Stefanko

This first Annual Report covers the work on Contract No. H0377043 "Cable for Face Equipment", from August 1, 1977 to July 31, 1978. It reports the progress in the three areas of over-and short-circuit protection, cable ampacity research and cable couplers. Field trips have established many interesting facts related to circuit breaker settings and cable size. For example, the determination of cable sizes depends on the RMS duty cycle current determined by a particular piece of equipment, but the actual selection of the cable to be used is often a function of the maximum allowable circuit breaker instantaneous settings as specified in Title 30. In order to avoid nuisance tripping as a result of instantaneous starting current field, laboratory and analytical studies are being conducted to determine proper settings and cable sizes Also an extensive program has been established to monitor the performance of high voltage cable couplers and determine their modes of failure. Various equipments are being designed for laboratory testing, and an extensive reeled cable experiment is also under way.

Jan 1, 1978