Search Documents

By John S. Lagarias

While systems to remove sulfur oxides from flue gases have been used at coal fired power plants since 1931, critical need for flue gas desulfurization has only occurred since the late 1960s following the passage of the Clean Air Act Amendments. Commercial and advanced flue gas desulfurization processes (FGD) are reviewed. Advantages and disadvantages of the processes are discussed. Regulatory requirements leading to the development of FGD systems are identified. The location and operation of coal fired plants may be determined more and more by the regulatory requirements for sludge disposal, waste, water discharge and air emissions.

Jan 1, 1978

By K. V. S. Sastry, S. C. Panigraphy, D. W. Fuerstenau

The batch balling behavior of hematite, magnetite and limestone was found to depend markedly on the grinding method used for feed preparation. Wet ground materials require higher moisture for balling than do dry ground materials. Further, as the fineness of the wet-ground material is increased, the overall rate of agglomeration decreases, whereas the opposite is true for dry-ground materials. In contrast, the resulting pellet size distributions are not affected by the nature of the feed material preparation. These differences and similarities in the agglomeration behavior between wet and dry ground materials may result from the hydrophilic/hydrophobic nature of the surfaces, the formation of pre-agglomerates during dry comminution, and possible variations in the packing density of particles in the agglomerates.

Jan 1, 1978

By Barry James

Energy, like labour and materials, is one of the basic production inputs in the industrial minerals industry. This paper discusses the significance of the changing energy situation in Canada as it affects the industry. It is apparent that the importance of energy as a management concern has increased considerably since 1973. The importance placed on energy management today will undoubtedly be an important factor in determining company and industry sector strength and profitability tomorrow.

Jan 1, 1978

Taxes have an impact on mineral resource availability in several ways. There is the obvious effect on the grades needed for mineral deposits to become economic orebodies. There are also indirect effects which can have equally significant impacts. The paper examines the appropriateness of different types of taxes in the mining industry. The effects of discriminatory taxes such as price-based royalties are described. There is a discussion on the feasibility of introducing a single resources tax to replace completely the various forms of taxes presently applied to the industry. The subtle impacts of taxes are described in a section covering the way in which apprehension over future possible changes to both the level and diversity of taxes is reflected in industry confidence. It is concluded that taxation can significantly limit the economic availability of mineral resources.

Jan 1, 1978

By D. S. Kimmel

The Bureau of Mines sponsored development of a system to remotely energize and de-energize the trolley wire in a section in response to demands from vehicles as they enter and leave the controlled section. The system developed utilizes a detector/actuator that controls a dc contactor at the outby end, and a 3 kHz oscillator at the inby end. A prototype system has been built and installed at the Bureau's trolley test site at Bruceton, Pennsylvania which has demonstrated the ability to also provide load discrimination for faults of 300 amperes or more. The system could readily be modified by locating the oscillator on the vehicle to provide automatic de-energizing of the trolley wire when the vehicle's pole is removed or the vehicle leaves the section.

Jan 1, 1978

The earliest U. S. patent on a crushing machine was issued in 1830. The device incorporated the drop hammer principle later used in the famous stamp mill, whose history is so intimately linked with that of the golden age of American Mining. Eli Blake invented the first successful mechanical rock-breaker --the Blake jaw crusher--patented in 1858. The idea of his mechanical principle, the powerful-toggle linkage, was so sound that today the Blake -type jaw crusher is the standard by which all jaw crushers are judged. In 1881, Philetus Gates was granted a patent on a machine which included in its design all the essential features of the modern gyra tory crusher. For some years after these pioneer machines were developed, crushing requirements were quite simple. All underground mining and open-pit quarrying was done by hand with tonnages and rock sizes generally small. In the milling of precious metal ores, stamp mills were popular as the final reduction machine. The stamps were fed with an ore size readily produced by one break through small gyratory or jaw crushers. Even in large underground mining operations, there was no demand for large crushers; and increasing tonnage requirements were met by duplicating the small units. The Homestake gold mine in South Dakota was a good example, where in 19 15 twenty -two small Gates gyratory crushers were used to prepare the ore for the batteries of 2,500 stamps. Open pit mines and the introduction of the steam shovel created a demand for larger crushers, which led to the development of a gyratory with an 18 in. (457 mm) receiving opening. Up to this time, the jaw crusher had kept pace with the gyratory, both from the standpoint of receiving opening and capacity; but now the gyratory stepped into a 15-year lead with larger and larger sizes. This trend toward large primary crushers started just before the turn of the century, and in 1910 crushers with 48 in. (1.22 m) receiving openings were being built. About this time, the jaw crusher was revived in a great contribution to primary crushing by the introduction of the 84 in. by 60 in. (2. 13 by 1. 52 m) machine. This crusher was usually followed by a 24 in. (6 10 mm) opening gyratory crusher for secondary breakage, a system which reawakened the industry to the use of the jaw crusher as a primary breaker. It is interesting that although his machines never came into general use, Thomas A. Edison ranks as a pioneer in the development of the large primary breaker. Edis on reasoned that the recoverable electrical energy

Jan 1, 1978

By G. E. Blight

The load-compression characteristics of mine supports are usually evaluated by means of relatively rapid tests, whereas in the mine they are subjected to much slower strain-controlled compression. The effects of slow strain rates on the load-bearing properties of mine supports were explored by means of straincontrolled tests on model timber packs and timber-filled steel telescopic props. It is shown that the load-compression characteristics of these supports are considerably influenced by the rate at which they are compressed. The species of timber influences the behaviour, but to a relatively minor extent. Preloaded supports are shown to lose a significant proportion of their preload by relaxation.

Jan 1, 1978

In several European countries, including Russia, it has become economically attractive to utilize peat as a fuel for power generation, the production of metallurgical coke, the production of fuel briquettes for the domestic market and low-Btu gas. Although the economic base and availability of energy supplies in Europe is much different than it is in Canada, regional economics here may warrant the development of peat as an alternative source of energy. Canadian peatlands cover several thousands of square miles and have historically been considered as waste land. Now, with the increasing costs of other energy sources, it is apparent that fuel peat should be re-evaluated as a potential energy resource. A nation-wide inventory of peat deposits has been prepared and reserves evaluated for some of these areas where field surveys have been carried out. The paper describes alternative mining methods developed to meet some of the various conditions encountered on virgin peatland . These mining techniques are generally based on current peat technology exercised in other parts of the world and would be applicable in some of the peat regions of Canada. Cost estimates have been prepared for peat production in regions of Canada, and the socio-economic aspects of a large-scale fuel peat operation are discussed. Several potential utilization schemes have been described, with particular emphasis on electric power generation. The paper makes recommendations for steps to be taken in the development of a fuel peat industry in Canada.

Jan 1, 1978

By Richard H. Lindgren

I appreciate this opportunity to discuss with you OPIC's new policies designed to assist U.S. minerals companies in developing new sources of minerals overseas. A comparison of recent figures on U.S. investment in mineral exploration, development and production gives results which are remarkable --and disturbing. Through the 1960's the flow of U.S. foreign direct investment in mining and smelting in the developed and less developed countries were nearly equal. However, by 1973, roughly 80% of all exploration expenditures by mining companies was taking place in the developed countries and principally in the U.S., Canada and Australia. Clearly it is to the interests of both the developing countries and the United States to put these figures back in better balance. As you may be aware, the administration as a whole is examining systematically what can be done by government to reduce the disincentives and increase the incentives to mineral investment in the less developed countries --the LDCs. A subgroup of the National Advisory Council chaired by the Treasury Department has been formed to coordinate U. S. Government policy and program efforts relating to mineral and energy development in these countries. Among other matters, this subgroup will examine how public policies could positively influence the private investment decision-making process in the minerals industry.

Jan 1, 1978

Prior to 1972, Peko Mines Limited at Tennant Creek used a central mill at Peko, which consisted of a gravity circuit, flotation and cyanidation of tailings, to treat their gold ore from surrounding mines. The Warrego concentrator, 60km to the west, was built to handle the Warrego and Gecko copper orebodies, which were being developed concurrently with the concentrator construction The Warrego concentrator consisted of a flotation circuit, using autogenous grinding at 100 - 120 tph, compared to the more elaborate Peko circuit employing rod mill - ball mill grinding capable of treating only 18 - 26 tph. During development of the Warrego copper mine a gold rich ore pod was located, because of which the mining plans were adjusted to allow simultaneous, separate extraction of the copper and gold ores. However, the plans for the concentrator were not affected as the gold ore could be carted 60km to the Peko central mill for processing.

Jan 1, 1978

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By W. R. Tyson

IT HAS BEEN KNOWN for many years that alloy steels can become brittle when tempered in the range of 350-600°C, or cooled slowly after heating to higher temperatures. The metallurgical literature reveals that blacksmiths were aware as early as 1883 that water quenching was necessary after heat treatment above 600°C to avoid brittleness. It has also been known for years that the problem is associated with trace impurities; a paper in the Journal of the Iron and Steel Institute of 1894 refers to the brittle, faceted fractures that occur in steels containing arsenic, phosphorus or sulphur. However, definitive investigation of the mechanism of embrittlement has been possible only within the last decade with the introduction of new experimental techniques to investigate surfaces, especially Auger electron spectroscopy. It is now possible to study in detail the chemistry of surfaces with a resolution of an atomic layer or two, and enormous progress has been made recently in studying the segregation of impurities to grain boundaries by exposing the boundaries by fracture inside the microscope. A clear picture of the processes occurring and their interpretation is now emerging, as was particularly clear at the recent 1977 ASM Materials Science Seminar on Interfacial Segregation held in Chicago in October. Recent research in this area has pointed the way for commercial exploitation of this new knowledge and experimental technology. It is the purpose of this article to trace progress in understanding temper embrittlement and to indicate other areas where control of interfacial segregation and its effects can be important in metallurgical applications.

Jan 1, 1978

By David B. McWhorter

Conventional analyses of seepage through saturated media do not apply when tailings impoundments are located above a partially saturated zone. Three stages of seepage are identified and methods for estimating the seepage rates and duration of each stage, based upon flow in partially saturated and saturated porous media, are demonstrated. The effectiveness of earthen liners is discussed and procedures for estimating the required properties of the porous media are provided.

Jan 1, 1978

By G. B. Gait

This report is the fifth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region. A catalog of the microfilmed maps of 47 of 49 major mines and 18 independent mines in the Southern field is presented. Previous reports included catalogs of microfilmed maps of mines in the Eastern Middle field, the Wyoming and Lackawanna Basins of the Northern field, and the Western Middle anthracite field.

Jan 1, 1978

By Wisecarver D. W.

Today the longwall is getting increasing attention in the United States as an excellent way to mine coal. This is not to say it is the best way in every mine because conditions, capital costs, and markets may well dictate another method. However, operators with working longwalls are often showing preference by phasing out room-and-pillar sections and replacing them with longwall. In the United States there are about 90 longwalls in operating coal mines and the number is increasing. In Europe, 95% of underground coal mining is by longwall compared with only 5% in the United States. In the Western States about 25% of the underground coal mines use longwall mining. There is logic behind the increase in longwalling. Compared to room-and-pillar mining, straight single-pass longwall has important advantages that show up in underground coal mining in any part of the country.

Jan 1, 1978

By Elber L, Whiten WJ, Cunningham KD, King GL, Bailey CW, Clay PA

The Savage River Mines concentrator treats magnetite ore at about 300 tonne/h, and produces feed for a pelletising plant. The plant incorporates two parallel grinding lines, each consisting of an autogenous mill, in closed circuit with a screen, a rougher mag- netic separator, a ball mill in closed circuit with parallel cyclones, and a finisher magnetic separator. Significant fluctuations in ore grade and grindability make it difficult to maintain pro- duct size in the narrow range desired, and to achieve maximum possible throughput at the same time, using the present largely manual control system. The present paper describes the develop- ment of a control system based on a mini- computer. It has been possible to implement a scheme of on-line estimation of product size which is sufficiently accurate for use in an automatic control system. The size estimation is essentially derived in terms of plant variables which control the ball mill cyclone cut size. Three control functions have so far been implemented and tested. These are control of the feed rate to the autogenous mill, control of water addition to the autogenous mill, and control of the ball mill sump level.

Jan 1, 1978

By Braham B

The Australian mining industry isstill labouring under the impression. created by the Fitzgerald Report that it does not pay suffic- ient tax. This would appear to be the raison d'etre of the resource rent tax debate. The authors quantitatively compare the cash flows to the mine and government resulting from a large strip coal mine in central Queensland under a number of Australian and international taxation policies. The Liberal government policies are found to be internationally competitive while the Labor 1975 policy is excessively punitive. The present value of the returns to the public from the Liberal 1977 policy vary between three and six times the net present value to the mine, which belies the necessity for the imposition of a super tax. The levelling of a special royalty, excess rail freight, by Queensland could severely re- strict the development of new mines in the Bowen Basin. The impact of excessive freight rates is analysed on a combined strip-deep mine typical of the new projects nearing development in the region. Otherwise economic mines can be made marginal or even sub economic by this tax. Even with moderate rail freights, the mining tax laws of New South Wales are more favourable to the industry than are Queensland's.

Jan 1, 1978

The mineral matter has been isolated from a selection of Australian bituminous coals using low temperature (radio-frequency) oxidation or hydrogen peroxidation techniques and the species present identified by x-raydiffraction. Quartz, kaolinite, and a range of mixed layer clay minerals are the dominant constituents of the coals studied, with carbonate, sulphate, and phosphate minerals abundant in some samples. The clay bands thatoccur within these coal seams contain similar mineral assemblages to the coals themselves, but the lutites that form the inter-seam strata have a markedly different mineralogy, characterized by abundant quartz andillite and a low kaolinite content.The kaolinite is thought to have formed chiefly by interaction of silica and alumina in the waters of the coal swamp, aided by the catalytic action of organic acids, while most of the other clay minerals are probablydetrital. The absence of illite from Australian coals is not fully understood, but it may reflect the action of organic acids on the detritus in the swamp, coupled with deposition in freshwater rather thanmarine conditions. Pyrite, although present in some coal samples when fresh, may undergo oxidation during storage to form a number of sulphate minerals, some of which may interact with any calcite present toform gypsum.The mineral matter assemblage in the coal determines to a great extent the fusion characteristics of the ash.Unless abundant carbonates are present, coals with kaolinite-rich assemblages have a very refractory ash, while those rich in chlorite or montmorillonite have ash fusion temperatures between 1000 and 1300°C. Theinfluence of the minerals on coal preparation and coking properties is also brieflY discussed, as well as the potential of mineral matter studies in coal seam correlation.

Jan 1, 1978

By Drew F. Holbrook

Most of the siliceous rocks of the Arkansas Novaculite are novaculite, but they also include some chert, siliceous shale and, rarely, sandstone. Novaculite is defined as a homogeneous mostly white or light-colored rock, translucent on thin edges, with a dull to waxy Juster, and comprised almost entirely of microcrystalline quartz. The most plausible theory of origin for novaculite is that primary silica from submarine volcanism was picked up by organisms and deposited as amorphous silica, which was subsequently converted to microcrystalline quartz (novaculite) through diagenesis. The Arkansas Novaculite crops out over an east-west distance of 200 miles in the Ouachita Mountains of Arkansas and Oklahoma. Three divisions of the formation have been defined: a Lower Division, almost entirely massive light-colored novaculite; a Middle Division of interbedded dark chert and shale; and an Upper Division of massive calcareous novaculite. The Lower Division and most of the Middle Division are Devonian in age, and the remainder of the Middle Division and all of the Upper Division are Mississippian. The massive novaculites of the Upper and Lower Division attain their maximum development along the southern and central outcrop belts of the formation in Arkansas, and it is these rocks that are the source of current silica production. The calcareous novaculite of the Upper Division weathers readily to a light-colored, porous, less brittle rock, and in places to tripoli deposits. Currently tripoli is mined from a single deposit near. Hot Springs, Arkansas, and the rock is processed for highly specialized filler and abrasive applications. In the vicinity of Hot Springs, Arkansas, certain novaculite layers from the Lower Division with unique textural characteristics are quarried and processed into whetstones. Several small quarries produce this rock for two local and one out-of-state whetstone-fabricating plants. Chemical analyses of composite samples of novaculite from both the Upper and Lower Divisions taken at widely separated localities average 99 percent SiOz indicating a substantial resource of high-silica rock.

Jan 1, 1978

By Gary E. McIntosh

This paper will discuss a U.S. Bureau of Mines project designed to assess and predict the impacts which surface coal mining will have on the regional shallow groundwater systems in the Powder River Basin. The primary objective will be met through the accomplishment of the following: (1) The design and establishment of a regional network for monitoring of shallow groundwater systems in the Basin. (2) Monitoring of the direction and rate of flow, water quality, and aquifer characteristics of the shallow groundwater systems. (3) Development of a regional groundwater simulation model with appurtenant subroutines to determine local effects.

Jan 1, 1978