Search Documents

By Diehl GW, Kuntonen J

The Tamrock all-hydraulic rock drilling system 400 has been developed to cover as wide a drilling range as possible, from 35 mm holes in tunnelling, roofbolting and development work to 64mm holes in long hole production drilling. Field experience during the last five years shows that the Tamrock drill covers this range in a way that no other rock drill on the market does and recently the range has been success- fully further expanded to cover bench drilling with 76 mm holes.

Jan 1, 1978

By Edgar S. Rush

This study was conducted to make a limited evaluation of experimental and standard tractor dozer blades. A field test program was conducted in the southeastern part of Kansas on strip-mined areas where the spoil banks are parallel with rest-to-crest distances between 90 and 120 ft and maximum dozing distances usually less than 50 ft. This evaluation was a part of an overall joint Pittsburg and Midway Mining Company--U. S. Bureau of Mines (USBM) Specialized Reclamation Field Test Program primarily centered on the field t sting of experimental high-volume lateral relocation blades. The three blades evaluated were the 60-ft-wide angle (A) blade mounted on two 41B tractors. a 48-ft-wide A blade mounted on two D9H tractors, and a 13-ft-wide reclamation universal (Rec U) blade mounted on a D9H tractor. In addition to the experimental blades, three commercially available blades were tested: A 20-ft universal (U) blade mounted on two side-by-side (SxS) D9H tractors; a 20-ft U blade mounted on a 418 tractor; and a l2-ft straight (S) blade mounted on a D8H tractor. The dozer blade evaluations compared measured blade performance with soil and other site characteristics and with estimated earth-moving performance rates based on earthmoving methodology that accounts for the traction and speed of the tractor. The earthmoving methodology was also validated with data collected during this program.

Jan 1, 1978

Martin Marietta Aluminum, Inc. followed Howmet Aluminum Corp., Revere Copper and Brass, Inc. and Anaconda Co. in lifting August prices of 99.5 percent unalloyed aluminum ingot by 3 cents to 56 cents per pound. Prior to these moves, Kaiser Aluminum and Chemical Corp. raised its June ingot listings by 4 cents to 57 cents and Consolidated Aluminum Corp., 4.5 cents to 57.5 cents. Domestic merchants increased July quotes by slightly more than 1 cent to 51.3-51.8 cents per pound. ARSENIC The Occupational Safety and Health Administration (OSHA) issued new standards, effective August 1, for worker exposure to inorganic arsenic, a toxic substance linked by OSHA to lung and lymphatic cancer. The new standard will limit worker exposure to 10 micrograms per cubic meter of air over an 8-hour period, a drastic reduction from the previous standard of 500 micrograms for a like period. Implementation of the new standards may be the most difficult and costly for copper smelters where arsenic is associated with the copper feed material but problems will also be encountered by producers of arsenic containing products such as for pesticides and herbicides. The new standards allow use of personal protective gear for workers as an interim measure until plant engineering controls can be put into effect.

Jan 1, 1978

By Wayne D. Gould, Terry O. Arney

The Pinto Valley digital control system is a supervisory system interfaced with a conventional analog control system. The design criteria, the hardware selection, and the startup of the system in the Pinto Valley concentrator are reported in depth. Examples of data collection application, as well as the present and immediate future implementation of control strategies, are discussed. This paper is a description of the digital data acquisition and control system that is installed at Cities Service's Pinto Valley concentrator.

Jan 1, 1978

By R. H. McMillan

A classification of important uranium deposits which utilizes both genetic and descriptive criteria is presented. The dual aspect is useful because, while the non-genetic nomenclature for the different deposit types is amenable to various interpretations, the critical characteristics of each deposit type can be analyzed to clarify various genetic points. Although the classification is intended primarily for Canadian uranium deposits, most of the important deposit types known elsewhere can be accommodated.

Jan 1, 1978

By A. J. Sinclair

Sampling methods for feasibility studies are dependent on geological characteristics of the deposit being evaluated. A preliminary geostatistical study is required, taking into account autocorrelation aspects of variables under study in order that sample plan design can be optimized to produce grade and tonnage estimates within stipulated error limits. In general, regular sample distribution is to be aimed for, and regular sample lengths (from drill core or cuttings, for example) are preferred in order to facilitate statistical analysis. Sample plans are modified and improved (either technically or economically), as a sampling program proceeds and additional information is obtained. Bulk samples for metallurgical testing can be evaluated in terms of the variance shown by all such samples in a deposit and the internal variability of grade. Attention to these sources of variability will ensure proper evaluation of pilot test results from bulk samples. In addition, a general mineralogical study of a deposit is an important, often ignored, requirement in a more general but semi-quantitative evaluation of the representativeness of a bulk sample; and, moreover, provides information useful in optimizing plant design.

Jan 1, 1978

By Zoltan Susanszky

Technical development in blasting requires improvement of industrial explosion techniques in two fields. One is to apply increasingly exact and economical solutions with more effective explosives, the other is to restrict as much as possible the environmental effect of explosions.

Jan 1, 1978

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By J T. Keim

Members and guests of the Society of Explosive Engineers, it's indeed a pleasure for a longtime practical user such as myself to have the ears of so many explosive experts for a few minutes just to express my feelings and concerns on blasting as well as the feelings and concerns of many other users and operators.

Jan 1, 1978

By Om P. Pande, Larry S. Diaz

Modern mineral processing plants could not operate efficiently, or even exist, without instruments which indicate, record, control, and in some cases anticipate the many changes that occur in a process. Even in plants which are operated manually, instruments are used to tell the operator when he should turn a valve or press a handswitch. Accordingly, all mineral processing plant engineering and construction projects must give careful consideration to this area of design activity.

Jan 1, 1978

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

Twelve years ago, Jeffrey Mining Machinery Division of Dresser Industries Inc. developed the 120H HELIMINER. This machine was the world's first fixed-drum continuous miner and soon became the standard among manufacturers of continuous miners throughout the mining machinery industry. This paper will first outline a brief history of continuous miner development, then discuss significant parameters which are essential to a successful continuous miner design, and finally describe a number of specific applications of Jeffrey continuous miners in a variety of materials, such as coal, potash, iron ore, and trona, around the world.

Jan 1, 1978

By R. C. O’Ferrall, W. G. Goulding

This paper describes the performance of a Robbins 52R Boxhole Borer from its introduction into the mine in July 1975 until late in 1977. As indicated by the costs involved, the performance has increased considerably and is expected to be even better once further envisaged modifications have been made. The average cost for the first half of 1977 was R275 per metre bored as against an average of R628 for 1975.

Jan 1, 1978

By Norman S. Smith, Troy D. Harris, Richard L. Ash

In open-cut bench blasting drilling boreholes below grade level is normally considered essential to insure toes do not remain. The extra drilling and use of explosive below floor level are not only expensive but on occasion cause serious problems including severe floor damage and excessive ground vibrations. It has been reported that under certain circumstances explosive in the subdrilling has been successfully substituted by broken rock with its associated benefits.

Jan 1, 1978

By B. R. Palmer, G. Gutierrez B., M. C. Fuerstenau

Selective flotation in nonmetallic systems is often complicated by the presence of iron-bearing silicates occurring as gangue. Minerals such as augite, diopside, hornblende, and tourmaline respond readily to flotation under the same conditions as ore minerals. Mechanisms by which these minerals respond to flotation with anionic collectors must be established if selective separations are to be made in these systems. It was the objective of this investigation to determine the mechanisms involved in the flotation of two pyroxenes, augite and diopside, with potassium oleate. Experimental Materials and Methods Pure potassium oleate, prepared by neutralization of oleic acid with KOH, was used as collector, while reagent-grade HC1 or KOH were used for pH adjustment. Conductivity water, made by passing distilled water through a mixed-bed ion exchange column, was used in this investigation. Two pyroxenes, [ ], were involved in this work. One member of this class of minerals was augite and was found to contain 3.3% calcium, 4.6% iron, and 9.6% magnesium. The source of this mineral was Tillamook County, Ore. The other pyroxene involved was diopside which contained 8.3% calcium, 2.7% iron, and 7.6% magnesium. The source of this sample was Bancroft, Ont. Microflotation experiments were conducted with a Hallimond cell. Mineral samples were ground dry and sized to 100 x 200 mesh. One-gram charges were conditioned for 3 min in the presence of various additions of potassium oleate. Flotation was conducted for 1 min with a nitrogen flow rate of 50 cm3/min. The electrophoretic mobilities of these two minerals were measured with a Zeta Meter in the absence and presence of [ ] salts and in the presence of an indifferent electrolyte, NaC1, added to maintain ionic

Jan 1, 1978

By W. F. Marshall

This Bureau of Mines report discusses tests conducted with four different catalytic reactor designs to determine the influences of exhaust treatment systems on emissions from diesel engines. Although there was significant differences in oxidation efficiencies at light to intermediate engine loads, all four catalysts were very effective in reducing emissions at heavy loads. Compositional determinations included carbon monoxide, carbon dioxide, unburned hydrocarbons, oxides of nitrogen, aldehydes, sulfur dioxide, sulfates, and particulate loading. Particulate size, exhaust odor intensity, and the character of the unburned hydrocarbon component were also determined.

Jan 1, 1978

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By Frederick Bloetscher

Means of improving the U.S. Bureau of Mines Brattice Window Method have been investigated by Goodyear Aerospace Corporation (GAC). An extensive series of laboratory tests at GAC and a series of tests in three operating coal mines of the Bethlehem Mines Corporation were conducted. The GAC laboratory tests defined the window coefficients and the accuracy of the method using different measuring techniques for a range of window sizes and shapes with window areas from 0.0873 to 4.0 square feet for flow velocities through the windows of from 100 to 1000 FPM. The results indicated that for the range of window sizes and window flow velocities investigated a single window coefficient value can be used with little error for each window size and for each flow direction, for the investigated range of window flow velocities. The mine tests developed techniques for quickly erecting the Temporary Test Stopping (TTS) in a cross-out, making the measurements, taking down the TTS and moving it and the test equipment to the next cross-cut. The time period for the total cycle ranged from 15-45 minutes depending on the properties of the cross-cut's surfaces. The total weight of the TTS and test equipment carried by the two miners conducting the tests was approximately 40 pounds. Correlation was obtained between the sum of the leakage values past 10 consecutive individual stoppings using the brattice window method and the value for the difference in the airway flow values before and after the 10 consecutive stoppings when the value for the sum of the leakages for the 10 was significant when com¬pared to the airway flow values. The mine tests reiterated the importance of using the largest TTS window(s) consistant with making accurate anemometer measurements for the best results with the brattice window method.

Jan 1, 1978

By R. D. Auten

This paper is primarily a report on the process of using oolitic aragonite, as received from Marconi& Ocean Industries, Ltd. without further processing, for a major portion of the raw feed to a rotary kiln producing cement clinker. Oolitic aragonite is a high purity calcium carbonate material, dust free, with the appearance of a course, white sand. It is farmed when under the right conditions of temperature ocean currents, and ocean floor topography. The calcium carbonate will precipitate into small spherical particles on the ocean floor. These oceanic conditions are correct to cause precipitation of the calcium carbonate near Ocean Cay in the Bahama Island chain. The present growing deposit near Ocean Cay is in the billions of tons and is mined by a relatively shallow-operation hydraulic dredge. The aragonite thus formed is en orthorhombic crystaline form of calcium carbonate with a specific gravity of approximately 2.9. At a temperature of 505°C. (940F), the aragonite converts to the hexagonal crystal of calcite with a specific gravity of 2.6 to 2.7. This change in specific gravity weakens the structure of the particles but the individual pieces are still fairly hard. When the material is then calcined at 900°C (1650°F), the particles retain their shape but become soft and will break up under finger pressure.

Jan 1, 1978

By John P. Norton

Microcrystalline silica has been mined in Illinois from the Clear Creek Formation since the turn of the century, especially in the area around Tamms in Alexander County, in the southernmost part of the state. This silica is consumed mainly by the abrasives and coatings industries, but is also sought after for many filler/extender uses. Production has grown with the economy with several new applications overshadowing traditional markets in recent years. Many of these applications are directly or indirectly related to energy saving factors. As a result of the "energy crisis" and "resin crunch," fillers have received a great deal of renewed attention as a desirable way of stretching the available resin supplies. With feedstocks in short supply and shortages existing in the entire petrochemical industry, the use of bulk materials to improve and extend existing resin is becoming an every increasingly important facet of plastics and coatings technology. Silica is the choise of fillers in applications where inertness, hardness, and low absorption are necessary characteristics. Microcrystalline silica has the additional advantage of being relatively easy to grind because the crude ore is a friable rock composed of tiny crystallites, many less than 0.1 u in diameter. Grinding represents a significant energy input in the production of silica flours. With energy costs increasing rapidly, comparable grades of silica flour made from microcrystalline silica have advanced less in price and it is expected this trend will continue in favor of the microcrystalline silica.

Jan 1, 1978