Search Documents

By John C. Ferm

Although roof falls account for approximately half of the fatalities in underground coal mining, the factors that produce them are not clear. Mining methods can account for some, but in others the controlling factors are the geological setting in which the mining takes place. The present investigation was undertaken to determine the kinds of rocks that were most likely to produce roof problems. Such knowledge would be helpful to mine planning since rock samples can be obtained in advance of mining by core hole drilling. The investigation was undertaken in underground mines in the Pocahontas #3 seam in southern West Virginia and southwestern Virginia. The Pocahontas #3 is one of the most widespread in this region and is a major source of high quality metallurgical coal. There are at least ten very large mines in the area and many smaller ones. The region has a very long mining history and considerable experience has been gained in roof control problems. The study was conducted with the support of the U. S. Bureau of Mines.

Jan 1, 1978

By Robert P. Vinson, Fred N. Kissell, Edward D. Thimons

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By Henning R. Norbom

Lime has been produced for many centuries. The simple pot kiln was one of the first devices used in this process. It was constructed of stone often on the side of a hill to reduce construction efforts and provide easy access to the top for feeding of limestone. It was fired from below with wood and coal. The pot kiln was very small and operated on the batch principle. The kiln being cooled between each batch, the fuel consumption was horrendous. The lime quality was poor with perhaps only one half of a batch being lime of suitable quality. Of the remaining half one part would be over burned and another part underburned. For centuries the lime burning technique was improved at a barely recognizable rate. One of the first major steps forward was the introduction of the continuous process vertical lime kiln. Although at first crudely constructed, the kiln had a refractory lining. It was charged with alternate layers of limestone and solid fuel usually in the form of coke. Continuous mode of operation, larger unit size and better heat distribution resulted in greatly improved fuel economy. However, quality of lime produced still left much to be desired. One problem was contamination by ashes from solid fuel.

Jan 1, 1978

By Raymond M. Stateham

Climatic conditions are compared with roof fall occurrence from April 1, 1972, to December 31, 1975, by the Bureau of Mines. These comparisons indicate that humidity has a strong influence on roof fall occurrence rates. Cubic regression techniques are used to develop best fit curves. Statistical analysis of these curves indicate that both are sinusoidal and exhibit positive correlation with each other. The sine waves have a period of 1 year with maximum and minimum inflection points in August and February.

Jan 1, 1978

By F. Botha, J. S. Adams, W. T. Ruhmer

The report describes the Amuran project in the Welkom area, which is being conducted by six members of the Anglo American Group. The project comprises three plants for the flotation of pyrite, a twin-stream uranium plant in which 'high-grade' slimes and pyrite can be leached separately, a pyriteburning sulphuric acid plant, and a plant for the recovery of gold from calcines. Details of these plants including capital costs and estimated production are given. Mention is made of the adsorption of gold onto activated charcoal and wet high-intensity magnetic separation as possible suitable processes for these residues.

Jan 1, 1978

Supergene nickel sulphide ore mined currently by Agnew Mining Company is at times partially oxidised to sulphate. The resulting soluble nickel, and calcium and magnesium in mill water, are shown to act as depressants in flotation. The depressant effect is favourably selective in that violarite, the main nickel mineral, is less affected than pyrrhotite. Nickel recovery, however, is adversely affected, probably through reduced flotation of complex sulphides. Soda ash consumption is increased markedly by the presence of the cations as shown by operating data and pulp titration tests. A significant increase in concentrate grade, from 9% to 14% Ni, was achieved late in 1981. One of the changes in plant practice which contributed to this improvement was the addition of soda ash to mill feed rather than to flotation feed as before. It is shown by laboratory tests that this reduced the depressant effects of the cations, thereby improving recovery at the expense of rougher selectivity, or equivalently, increasing concentrate grade at constant recovery. The selective depressant effect cannot be exploited until scavenger recovery is improved and a scavenger concentrate regrind-retreat äcircuit is implemented. Development is

Jan 1, 1978

By S. J. Patchet

The use of fill in deep-level gold mining presents the possibility of achieving considerable economic and operational benefits if conventional support can be eliminated. Unfortunately, the combination of the properties of tailings from gold reduction plants and the narrow, flat, tabular reefs being exploited make conventional hydraulic filling very unpractical. Laboratory tests indicate that, with careful control of water content, these tailings can provide an adequate fill material. A variety of bonding agents have been investigated, and the most practical seems to be ordinary Portland cement. Even at very low cement contents some cohesion is achieved. The design and layout for a complete fill support system using hydraulic transport, dewatering, and pneumatic placement are discussed, and a surface field trial indicated that the principles involved are correct and that acceptable results can be achieved. This system and material would completely eliminate conventional timber and brick support, and a preliminary economic analysis indicates that filling is cost competitive on a direct replacement basis. All the operations for a full-scale operation are available or have been developed to a stage sufficient to indicate that the system is practical, although certain operations require further refinement.

Jan 1, 1978

To reduce the possibility of injury to operators and damage to equipment caused by collision of mining vehicles during coal loading. Approach An energy-absorbing bumper was developed and tested underground on a continuous miner. How It Works The bumper, a long box-like weldment backed by five energy absorbers, is attached to a continuous mining machine by a hinge behind the cab. See Figure 1. When a shuttle car collides with the bumper, or when it is otherwise struck, the energy absorbers are compressed. This absorbs and dissipates part of the kinetic energy of the colliding vehicle, thereby reducing or eliminating its destructive effects. Each energy absorber consists of two chambers separated by a freely-moving piston. One chamber (Figure 2) contains hydraulic fluid. The second chamber contains a gas. When a collision causes the absorber to compress, the hydraulic fluid in the first chamber is forced past a metering pin and through an orifice. The hydraulic fluid then pushes against the piston, compressing the gas in the second chamber.

Jan 1, 1978

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

Tonnes per Hour - Kilowatts per Tonne Tonnes of Mesh Size Produced Kilowatts per Tonne of Mesh Size Produced - Terms often heard in discussions of grinding mill and grinding circuit performance. All of them only tell a partial story as none of them relate to a fixed reference or overall standard measurement. Tonnes per Hour gives the production rate relating it to a specified or desired rate set as a goal or objective. As such it does not take into account changes in feed size, product size or grindability. Kilowatts per Tonne which accurately stated is kilowatt hours per tonne brings power consumed into the picture which is related to grindability but still does not take into account changes in feed size and product size without which power changes do not necessarily reflect the complete effect of changes in Grindability.

Jan 1, 1978

The theory of geostatistics covers a branch of .applied statistics aimed at a mathematical description and analysis of geological observations. Geostatistics can be used in pure geology (for example, for the analysis of trace elements in a metamorphic rock), in mineral exploration (for example, for the analysis of geochemical exploration data), as well as in mine valuation. This book is intended to provide a practical introduction to the theory of geostatistical methods of mineral evaluation. Over the years, various mathematical models have been developed to represent the distribution of values in mineral deposits. The simpler models are based on the assumption that the values are randomly distributed. Classical statistical methods, based on this assumption of the random distribution of values, are used to analyse mineral deposits to which these models apply or are assumed to apply. In all mineral deposits, however, one recognizes the presence of areas where the values are higher or lower than elsewhere. Also, the values of two samples in a mineral deposit are more likely to be similar if the samples are taken close together than if they are taken far apart. This indicates that there exists a degree of correlation between sample values, and that this correlation is a function of the distance between the samples. Models have been developed which take this correlation into consideration, with the degree of correlation between sample values being usually measured by the semivariogram function. In these models the fact that two samples taken next to each other will most probably not have the same value, must also be considered; even for very short distances the correlations are usually not perfect and a purely random component is present in the value distribution. The mathematical models will therefore assume the presence of two sources of variability in the values: a correlated component and a random component. Finally, one must consider the particular and very common case of mineral deposits in which the values present a systematic variation in space. This variation is usually referred to as a drift, or a trend. For example, the grade of an ore body may increase with depth of the ore, or it may decrease when one moves away from a central volcanic pipe. The earlier models did not give a satisfactory representation of drifts, and more complex models have been developed, in which three sources of variation are represented. These models are made up of: a deterministic component, a correlated component, and a random component. The deterministic component is used as a model of the drift. The correlated component explains regular changes in values which are not represented by the drift. The random component represents variations which cannot be explained by any of the above factors. The simpler models, based on the assumption of a single random component, will be described first (Chapter 2). The models based on the hypothesis of the superimposition of a correlated component on a random component, will then be analysed in detail. These models are most commonly used in the analysis of mineral deposits (Chapters 3-1 I). Finally, how to deal with the presence of a drift will be briefly described (Chapter 12). This book has been written essentially for students in mining engineering and for mining engineers who are interested in the background to the theory of geostatistics as well as its practical applications. The assumption is made that the reader has an elementary knowledge of statistics. Some knowledge of linear algebra is useful in part of Chapter 9, and is necessary to read Chapter 12. A proof is given of all the equations related to geostatistics, and which are not usually found in elementary textbooks on statistics. Understanding of these proofs is not necessary for practical application of the theory, and the reader may wish to skip them on a first reading, concentrating attention on the numerous simple practical examples given. Although the theoretical geostatistician will not find much new material in this publication, it is anticipated that he will develop some interest in the practical approach chosen to prove the various geostatistical equations. Many people and institutions contributed to the preparation and completion of this work. I am much indebted to Dr D. G. Krige and the Anglo Transvaal Consolidated In- vestment Company Limited, who gave me the opportunity to spend a considerable amount of time working on geostatistical problems, both theoretical and practical, during the time that I was in their employment. Dr Krige contributed greatly in developing my interest in studying both the theory and practice of geostatistics, always insisting that a correct balance be kept between theory and practice. I am grateful to Professor H. M. Wells and the Mining Department of the University of the Witwatersrand for inviting me to give lectures in a post- graduate course on geostatistics. The notes 1 prepared for that course became the foundation of the present work. I am also indebted to the Centre de Geostatistique of the École des Mines de Paris, where I received my first formal education in geostatistics during a summer course given by Charles Huijbregts, after many years of my lonely plodding through the published literature. Many graphs in the present volume are reproduced with the permission of the Centre de Geostatistique. The Department of Metallurgical and Mineral Engineering of the University of Wisconsin-Madison has also contributed in making this work possible, by allowing me to spend a considerable amount of time and resources in the writing, typing, and correcting of successive drafts. I am thankful to Lynn D. Kendall, who typed the entire manuscript under constant pressure.

Jan 1, 1978

By Gene M. Handel

Today the world is heavily dependent on petroleum for its energy. In the United States, over 75% of the primary energy used comes from petroleum. Other developed countries are similar. The less developed countries have a lower dependence on petroleum just as the United States did through the early 20th Century. However, these less-developed countries look upon petroleum as one of the primary energy sources for the economic growth required to improve their standard of living. So everyone considers petroleum an essential ingredient in the recipe for the good life. But there is a substantial problem with this recipe, and it is finally getting general recognition. Petroleum is a finite resource, and the world is using it up at a rapid, accelerating rate. Though it won't be exhausted for many decades, the early warnings of ultimate limits have already appeared. The suppliers of the incremental production in the Middle East have threatened to restrict increases in their production rates. And, of course, the short term embargo of four years ago clearly demonstrated the economic impact of reduced access to petroleum as a primary source of energy. World petroleum production will probably peak in. 10 to 15 years and then start declining. When that happens, economics--the allocation of scarce products (also known as the dismal science for obvious reasons)--indicates that the price of petroleum will escalate in real terms. So that's the situation today. We have a serious and growing problem facing us that could substantially alter the quality of our life over the next 25 years. Recognition that the society may face a period of lowered expectations after a long period of upward mobility will be a painful experience, but it is certainly not the moral equivalent of war. And, besides, we have time to take positive actions to avert the most serious consequences. When we consider alternate energy sources, the possibilities are almost endless: coal, oil shale, tar sands, solar, fission, fusion, wind, tides, biomass, etc. Actually, the list is endless because new possibilities are continually being proposed. Of these possibilities, coal uniquely stands out as an attractive substitute for petroleum. Coal can be, and is, burned to generate electricity and provide heat. It can be liquefied to supplement the liquid fuels from petroleum, and it can be gasified for use as synthetic natural gas. Unlike exotic alternate energy such as solar and fusion, coal has successfully been used commercially to produce synthetic fuels. But, the technology does need to be refined and modernized. Thus, coal's role is not to be "America's Ace in the Hole," but to bridge the transition from primary dependence on petroleum for energy to the utopia of renewable sources of energy. But don't be mislead by the prophets--those renewable sources of energy are going to be very, very expensive when they are invented.

Jan 1, 1978

By Howard M. Cotton

Early in 1977, Amoco Production Company and Houston Chemicals, a subsidiary of Pittsburg Plate Glass (PPG) Industries, started producing iodine commercially in northwestern Oklahoma. This is significant because it is the first plant in over 40 years to be built in the United States with iodine as its sole commercial product. With the exception of a limited amount of iodine produced by Dow Chemical in Michigan, the United States is dependent upon imports from Chile and Japan for its iodine needs. The two million pounds of iodine produced annually from the Woodward plant will supply over one-third of the United States' requirements. Routine analysis of subsurface brines by the Formation Water Lab at the Amoco Production Company Research Center in Tulsa, Oklahoma, revealed unusually high concentrations of certain potentially economic minerals. Investigations determined that, of the minerals in question, iodine appeared to offer the best potential. The brines in question are located in the Morrow sands (basal Pennsylvanian) at a depth of 7,175 to 7.400 feet, in an area where Amoco has been active in a gas play for the past 20 years. The regional iodine concentration ranges from 10 to 700 ppm and averages around 300 ppm with the project area. The project is located 8 miles north and slightly east of the town of Woodward, where the well-developed, porous, and permeable sands of the Woodward trench contain large volumes of brine.

Jan 1, 1978

By Whiten WJ, Narayanan S

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. This analysis reveals that the relative power inefficiency of large ball mills is due to inefficient grinding of coarse (plus 4 mm) particles in these mills. A qualitative physical hypothesis is proposed to explain this behaviour. The results of the analysis can be used to scale up ball mill behaviour, using the mathematical models and techniques developed. A simpler ball mill scale-up procedure is also proposed, and its limitations stated. Laboratory experiments are being conducted to determine the average size distributions of single particles of different ores after breaKage. These experiments can distinguish between the different ores, and it is hoped to use their results to model and predict the grinding of different ores in ball Mills.

Jan 1, 1978

By C. Gutiérrez

Flotation and adsorption studies of ilmenite with technical oleic acid, pure oleic acid, and mixtures of each of them with n-hexadecane have been conducted. From them it is concluded that the depression of ilmenite caused by a too long conditioning time is due to adsorption of the collector onto the fines produced by attrition in the conditioning cell, and that fuel oil is necessary for economic flotation of non-deslimed ilmenite ore. This beneficial effect of fuel oil is attributed to van der Waals forces, of the hydro-carbon chains.

Jan 1, 1978

By A. Renton Amell

The rate of dissolution of U02 was measured in acid solutions similar to those used for in situ leaching, with S04 of 10-1.82 to 10-4 M, Fe(III) of 10-2 to 10-4 M and pH's of 1.1 to 2.3. The dependence of dissolution rate on pH was small and inconsistent, probably reflecting the combined effects of a very weakly polar oxidizing complex, probably FeSO4+, and a nearly neutral U02 surface. Differences in the state of the U02 surface may explain this variability as well as contrasts between these results and results reported in other work. Changing either S04 or Fe(III) concentrations significantly affects dissolution rates. Increasing low sulfate concentrations in solutions containing 10 2 M Fe(III) at pH 2 results in formation of FeSO4+. In such solutions, rates increased with (S04)/(Fe(III)) up to 1:30, thereby indicating that the oxidation of U02 by FeSO4 is more rapid than by Fe3+. However, the dissolution rate decreased at higher (SO4)/ (Fe(III)), due either to sorption of SO42- on the UO2 surface or to formation of other less reactive sulfate complexes such as Fe(S04)2 or FeHSO4+ However, Fe(III) concentration is the dominant factor in determining solution rates. The rate was directly proportional to ferric iron concentration, indicating that the rate-determining step of the dissolution reaction is a single-electron oxidation by a ferric complex. Dissolution rates were lower in solutions of 0.1 and 1.0% H202 (0.029 and 0.29 M) than at similar concentrations of ferric iron because of formation of an insoluble surface coating of uranium peroxide, UO4?4H20. This phase may limit the value of hydrogen peroxide as an oxidant in lixiviants, not only by its very low solubility, but perhaps also by filling pores and reducing permeability in the ore body.

Jan 1, 1978

By Patrick M. Hurley

The relationships between mineral deposits and various plate margin mechanisms are examined under the constraints of radiogenic isotopes and other geochemical indicators. It seems like1 y that: (1) deposits of the spreading ridge association are fairly ubiquitious through most of geologic history and can be recognized by the lithologic assemblage and primitive lead isotope ratios; (2) most metals in the island arc association are not derived entirely from a subducting oceanic plate, and have a partly continental affinity; (3) subduction beneath a continental plate generates ores which are derived either from the downgoing plate or from the lower crust; (4) the heating of a continental plate by thickening or by mantle plumes may develop a metallogenic province involving extraction of metals from the curst; (5) rifts and grabens developing thick sections of marine sediments with evaporites may be the locus of base metal mineralization by movement of reducing brine solutions resulting from diagenesis and bacterial reduction of sulfates

Jan 1, 1978

By Michael J. Beus

This Bureau of Mines report describes a tunnel stress relaxation gage (TSR) developed to measure initial radial displacement around full-sized underground openings. The TSR technique was shown to be a valid concept in previous field verification tests. Sensitivity has been improved by employing a titanium alloy cantilever in the transducer head, which also permits a deeper sensor location. Use of improved fabrication methods such as stainless steel bellows and sputtering techniques and use of an environmental chamber for testing greatly increased overall reliability. A miniature data acquisition system (DAS) was interfaced directly to the transducer for increased versatility and containment entirely within a borehole. The present TSR system is suitable for use around full-size underground excavations, particularly machine-bored openings. Field evaluation of the improved instrumentation verified the design goals.

Jan 1, 1978

By Ernest A. Curth

The Bureau of Mines and Old Ben Coal Co. concluded a cost-sharing contract in 1975, the objective of which was to demonstrate the Herrin No. 6 coalbed in southern Illinois can be mined safely by longwall methods. Under the agreement, three longwall panels are to be mined at Old Ben No. 24 mine. A premining investigation laid the groundwork for specifying a roof-support system designed to control hazardous ground. Old Ben Coal Co. and Bureau engineers selected lemiscate-type roof shields. A rock mechanics program and geological mapping provide early warning capability and criteria for future equipment design. The effect of mining on the surface was monitored by a surface survey to develop subsidence-prediction criteria for the Illinois coal basin. The first of the three longwall panels started up in September 1976 and was completed in May 1977. The major adverse condition was the occurrence of limestone concretions, called coal balls, in massive pods. The shields provided adequate roof control even in faulty ground. Operation of the second panel started on August 1, 1977, following panel-to-panel transfer of the equipment. The accident rate was low.

Jan 1, 1978

Techniques and results achieved during the excavation of the Melbourne Underground Rail Loop (HURL) are summarised and discussed in the context of the various restraints present in a typical urban construction project. Mechanical methods (as distinct from those utilising blasting)accounted for the bulk of the excavation. Ground support was critical in this particular geological excavation setting, but is not discussed in detail except insofar as it constitutes a restraint to excavation progress.

Jan 1, 1978