Search Documents

By Turner T. M

The problem of metering fine particulate material at low flowrate is often encountered in metallurgical experiment. This note describes a feeder which wa developed to provide metered flows of copper sulphide concentrate in the range of 0'1-0'7 g/min.It is believed that the present device is easier to operate than previously described feeders (e.g. Hamor and Smith, 1971). It may have applications in the field of analytical chemistry, as well as in metallurgical investigations.

Jan 1, 1978

By J. H. Perry

The Bureau of Mines is conducting research to determine the effectiveness of long holes in degasifying an area of the Upper Split of the Lower Sunnyside coalbed at Kaiser Steel Co.'s Sunnyside No.1 mine. These holes were drilled from the two outside entries of a section that was closed to mining because of excessive methane emissions. Two holes drilled to 430 and 450 feet produced initial gas flows of 160,000 and 127,000 cfd, respectively. Sixteen days after the completion of the second hole, the total gas production declined to just over 144,000 cfd. In 9 months of degasification, over 35 MMcf of commercial-quality gas has been removed from the coalbed. The combined gas flows declined to 106,000 cfd in the 9-month period. The two holes have reduced face emissions by about 40 pet.

Jan 1, 1978

The introduction of large diameter holes to underground mining has provided the first opportunity to apply near spherical charges in production scale blasts instead of the convent- ional long cylindrical charges generally used in stope and pillar mining. A modified version of the cratering prin- ciple was applied in the blast design in extrac- ting ore across a horizontal area of a stope or pillar. The new rock breaking technique has developed into the Vertical Crater Retreat (VCR) mining system and eliminated raise boring, slot cutting and dilution of the ore by back- fill material. Furthermore it has reduced labour and time requirements thus becoming not only a low cost method of mining but the safest method of underground mining known today. Exceptionally fine muck is provided with a minimum of damage by blasts to walls and re- treating backs of the stope or pillar. The VCR method can also be used for drop- raising, and for the excavation of underground cavities for almost any purpose . The proper explanation of the breakage mechanism of the near spherical charges opposite to the cylindrical charges yet to be found. The mining industry has quickly recognis- ed the value of the VCR mining method which is being adopted by an increasing number of mines

Jan 1, 1978

By V. S. Papezik

Pyrophyllite, an AI silicate used in the production of ceramic materials, is formed mainly by alteration of felsic to intermediate volcanic rocks, either directly (at temperatures of 250-300°C and pressures of 1-2 kbar) or by subsequent low-grade metamorphism of aluminous protoliths produced by thermal fluids or even by prolonged weathering. Most pyrophyllite deposits in North America are concentrated in a belt of Late Precambrian volcanic and sedimentary rocks, the "Avalon Zone ", which extends along the eastern flank of the Appalachian mountain system from Newfoundland to the southeastern U.S.A. The only producing pyrophyllite mine in Canada is an open pit located near the settlement of Foxtrap on the Avalon Peninsula of Newfoundland. It lies in a belt of rhyolitic flows and pyroclastics intruded by a granitoid pluton. The rocks have been leached along a shear- or fracture zone, depleted in silica, alkalies, Ca, Mg and Fe by the action of hydrothermal fluids, and recrystallized to a very fine-grained massive assemblage of pyrophyllite, muscovite ("sericite") and quartz. High-grade pyrophyllite lenses contain small nodules of diaspore with minor barite; rutile is present in trace amounts. The close proximity of all pyrophyllitized zones on the peninsula to the granite contact suggests that the alteration was produced by thermal fluids genetically connected with the granitoid pluton. The fine-grained pyrophyllite-bearing rocks, with their simple mineralogy, are suitable for quantitative modal analysis by X-ray diffraction. Chemically analyzed samples from the alteration zone were used for the construction of working curves by plotting calculated mineral content against the intensity of selected diffraction peaks. The accuracy of the resulting curves is ±4.5% for quartz, ±3.6% for pyrophyllite and ±2.7% for muscovite. Pelletized samples give best results. The XRD method is suitable for a rapid analysis of a large number of grab or core samples to outline higher-grade areas for more detailed sampling.

Jan 1, 1978

By Jr. Babcock

The Pyke asbestos deposits were discovered by Kennecott Explorations (Australia) Pty. Ltd., in 1969 during the course of base metal exploration on the South Island of New Zealand. Extensive occurrences of chrysotile asbestos were found associated with the Red Mountain Ultramafics in the headwaters of the Pyke River, and to the north and south along the ultramafic belt for a distance of 70 kilometers. Surface evaluation and drilling by Kennecott in 1970 and 1971 identified numerous small deposits of good grade fibre in the Little Red Hills between the Pyke and Barrier Rivers. Additional drilling and three adits have been completed by other companies since that time. The property is presently held by Lime and Marble, Ltd. Of Nelson, New Zealand, and Kennecott Explorations (Australia) Pty. Ltd. This paper will present the regional and local setting of the asbestos deposits, including the geology and nature of mineralization. In addition, the exploration methods used by Kennecott in the discovery and evaluation of these deposits will be outlined. Subsequent work by other companies will be mentioned, but not described in any detail. This subsequent work did not alter Kennecott's conclusions or produce any serious changes in the interpretation of geology and mineralization. The author acknowledges the contribution of the many employees of Kennecott Explorations (Australia) Pty. Ltd., who have been involved in the project, particularly Ramon Farmer, N. G. Comer, and A. W. McConie, who were responsible for completion of field work and reporting on the project. The responsibility for the conclusions and interpretations of this report are solely that of the author and result from his involvement in discovery of the deposits and management of the exploration program.

Jan 1, 1978

By G. M. Swinkels

Sherritt Gordon and Cominco, with financial assistance from the Canadian Government through PAIT, have developed a hydrometallurgical process for refining copper from sulphide concentrates. The main objective of the project was to develop a process applicable to a wide range of concentrates with respect to copper content, other metals content and impurities, within the economic parameters set by present smelting and refining practice. Other important objectives were to recover sulphur in its elemental form and not as sulphur dioxide to assure improved hygienic conditions and a negligible impact on the environment. For the most abundant and relatively refractory chalcopyrite concentrates, the first step of the process is thermal activation with hydrogen to decompose chalcopyrite and pyrite, commonly associated with it, into more reactive sulphides more amenable to leaching. The iron is then selectively extracted by sulphuric acid leaching and subsequently rejected as jarosite. High-bornite concentrates do not require thermal activation and acid leaching; they are subjected to another hydrometallurgical iron removal step. The high-grade copper sulphide resulting from iron removal, and containing all of the initial precious metals, is then leached under oxygen pressure to produce elemental sulphur and copper sulphate solution . After suitable solution purification, the copper is recovered by high-current-density electrowinning as wire-grade product. Precious metals remain in the leach residue and are recovered after separation of the gangue materials and elemental sulphur. The laboratory and pre-piloting test work had indicated copper and precious metals recoveries comparable to those achieved in current practice. The process was shown to be suitable for handling relatively low-grade concentrates and, in addition, it was capable of high recoveries of associated zinc, molybdenum, nickel and cobalt in saleable form.

Jan 1, 1978

By Douglas C. Fraser

A DIGHEM survey was flown in the Belford-Montcalm Township area of Ontario in November 1975. This 600-linemile survey resulted in the detection of 134 EM anomalies. The Montcalm Township copper-nickel discovery yielded a single-line anomaly having a conductance of 154 mhos. This anomaly was highly visible because (a) it had the highest conductance in the survey area, (b) it correlated with a 175-gamma thumbprint-shaped magnetic anomaly and (c) it was isolated from long conductive bands. The deposit is a copper-nickel pyrrhotite body which occurs in gabbro and strikes north-south, parallel to the flight lines. The DIGHEM survey was flown north-south, because the exploration program was primarily concerned with locating copper-zinc sulphides in the east-west-striking felsic volcanics. The flight line passed close to the deposit and yielded a 9-ppm anomaly on the chart record. The computer analysis showed that a deposit of exceptionally high conductance (154 mhos) caused the relatively weak (9 ppm) anomaly. The ground follow-up program of magnetics and EM led quickly to the discovery drill hole, which penetrated the orebody in September 1976. Subsequent geophysical surveys consisted of horizontal-loop EM, pulse EM, magnetic and induced polarization surveys over an area of about 8 claims. In addition, a detailed DIGHEM" airborne survey was flown at a line spacing of 100 m to evaluate the entire property of 620 claims. This detailed survey yielded EM conductor maps and contour maps of resistivity, magnetics and enhanced magnetics.

Jan 1, 1978

By R. H. Wallis

Weighted moving-average contour maps have been constructed for molybdenum, copper and zinc using 7850 stream-sediment samples from 5430 square miles (14,063 sq. kms) of south-central British Columbia. Regional trends for molybdenum and zinc are northeast, north and northwest and those for copper are north and northwest. These trends are interrupted by zones markedly low in metals . The metal-rich trends cross rocks of different lithology and age and thus appear to be structurally controlled. The northeast trend may have exerted control on metal distribution at two different times.

Jan 1, 1978

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Aust- ralia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are begin- ning to experience where industry no longer `calls the tune'. We miners have been quick to point out and emphasize, that ours is a `high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to elim- inate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

By W. W. Wen, S. C. Sun

The objective of this investigation was to study the electrokinetic behavior of oxidized coals to indicate the feasibility of separating oxidized coals from ash materials and pyrite by an amine flotation process. The effects of soluble inorganic electrolyte products from coal oxidation were also examined. The electro-kinetic behavior of coals of different rank and degree of oxidation were studied by an electro-phoreses technique. Generally, increasing the oxidation increases the negative value of the zeta-potential and decreases the isoelectric point (IEP). Flotation results indicate that the flotation recovery increases with decreasing pH values, and that with ferrous sulfate at pH 6.5 the flotation recovery is optimum while the pyrite is depressed. Comparing the flotation results with the electokinetic results verified that in the presence of ferrous sulfate, the maximum hydro-phobicity of oxidized coal with dodecylamine and frother is near its IEP, which is around pH 6.5 to 7.0.

Jan 1, 1978

By Raymond Dallaire

The Humphrey's spiral is a static gravity separation device which cannot be adjusted to match short-term variations that occur in the feed. Any disturbance in the feed grade, per cent solids or flow rate affects substantially the recovery and grade of concentrate. Such variations must be minimized in order to maintain the desired rate of production and quality of the product for which the installation has been designed. A study has been performed in which the foregoing assertions were quantified. The feed grade, per cent solids, flow rate and particle size were varied independently. Ore from Carol Lake, Nfld., was used throughout the experiments. This consisted of specular hematite and magnetite in a silica gangue.

Jan 1, 1978

As the gold price, and consequently ore reserves, improved in the late 1970's, a programme of upgrading the gold recovery circuit at the Phoenix treatment plant at Central Norseman was initiated. The introduction of oxidised ore with a high clay content from the North Royal open cut caused a reduction in thickening and filtering capacities, which in turn restricted plant throughput and increased gold losses in the residue solutions. Test work into alternative washing facilities showed that the installation of a five stage counter current decantation system would restore throughput and reduce soluble gold losses. Installation of the system achieved the objectives of increased plant tonnage, increased proportions of the high grade oxidised ore in the mill feed and decreased gold losses in the residue waters.

Jan 1, 1978

By P. S. Sundar

A laboratory method for the simulation of in-situ leaching of uranium was developed under contract to the Interior Department's Bureau of Mines. Simulation tests using sulfuric acid, ammonium bicarbonate and sodium carbonate as reagents and hydrogen peroxide as oxidant were carried out with representative ores from Texas and Wyoming. The tests not only yielded recovery rates of uranium and permeability changes, but also qualitative inferences on the chemical and physical phenomena which occur underground. Leaching with basic solutions was found to be kinetic constrained and with acid solutions, equilibrium constrained. The rapid permeability changes observed when leach solutions were introduced, were probably caused by gas blockages in the packing. Precipitation of calcite or gypsum and the reaction of clay to leach solutions had slow and gradual effect on the packing permeabilities.

Jan 1, 1978

By Stanislatv Pawlowski

New, large sulphur deposits were discovered in Poland in 1953, the result of investigations by the National Geological Institute. All deposits occur in a widespread Miocene evaporite unit in the Carpathian foredeep. The gypsum underlying impermeable Sarmatian clays was altered to limestone and native sulphur where penetrated by hydrocarbons and bacteria. All deposits occur in Miocene structural uplifts. The early determination of the genesis of the sulphur deposits and their occurrence in elevated blocks led to an exploration program that successfully located new deposits.

Jan 1, 1978

By Jr. Freed

Basic design features, details of the face ventilation system, roof support and Operator protection system, certified lighting, and in-mine evaluation plans are presented for an Automated Extraction System (AES) that has been designed to fill needs which are present in the Mining Industry. The philosophy of design and proposed operation of the machine, as well as the relationships between these factors, are reviewed. The AES is designed to help overcome production problems resulting from the regulation of roof control, clean-up, ventilation, dust suppression, and operator protection required by the Federal Coal Mine Health and Safety Act of 1969. The design permits more continuous operation and greatly improves operator safety. The machine is a full-face drum-type continuous miner which includes self-advancing, continuous temporary roof support and permanent roof support equipment. Onboard self-advancing face ventilation, dust suppression, and air scrubbing equipment are also included in the design. A further improvement over existing equipment is the incorporation of an automatic programmed cutting cycle control system. All mining functions including movements of the roof support system are handled by this automatic system.

Jan 1, 1978

By Stephen W. Lambert, Michael A. Trevits

The Bureau of Mines examined the wellbore of a vertical gas drainage well in the Mary Lee coalbed to determine the results of specific completion procedures in coal. A jet-slotting tool was used to cut four vertical slots through the casing about 1 ft below the coalbed. Even though stimulation treatment pressure was excessive, hydraulically induced channels were contained entirely within the target coal zone. Sand-filled, induced channels were horizontal, inclined, and vertical, and were propagated in directions similar to bedding planes, rock joint, and coal cleat directions measured in the mine. Variable gas flow rates, recorded during the productive life of the well, were attributed to chronic downhole pump malfunction and the slotted casing below the production zone.

Jan 1, 1978

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

The mathematical models of semivariograms can be classified according to whether or not they correspond to situations where the second order stationarity conditions are satisfied (§ 3.3.4). If second order stationarity exists, the a priori variance s2 of x (z) also exists and is finite. For large distances h such that x (z) and x (z + h) are not correlated, the semi- variogram ? (h) will reach a value equal to s2 [this is a consequence of (3.27) above]. This limiting value is called the sill C of the semivariogram, and the distance at which ? (h) reaches the sill is called the range. The range of the semi- variogram obtained from a given type of sample corresponds to the distance of influence of these samples. If only the intrinsic hypothesis is satisfied, the sample variance is an increasing function of the size of the area or volume in which the samples are located, and the semivariogram ? (h) will be a continuously increasing function of h. Remark: It will be shown in Chapter 7 that the variance s2 of x (z) in the ore body O is equal to the average value of ? (h) in O. If ? (h) is a non-decreasing function with sill C, the average value of ? (h) in O will be less than C. s2 and C will be equal only if for some values of h in O, ? (h) exceeds C. In practice, if the range of the semivariogram is small with respect to the dimensions of the ore body, the difference between C and s2 will be negligible.

Jan 1, 1978

By Timothy R. Eby

"The Wabush Mines project was formed in 1956 to develop a large iron ore property in Western Labrador. The town of Wabush along with the mining and concentrating facilities are located 640 air miles from Montreal, and 734 air miles from St. John's. The operation has been in production since late 1964.While mining and concentrating operations are located in Labrador, the pelletizing facilities are situated 275 miles south at Sept-Iles, Quebec. Dedicated in 1965, Wabush produces six million tons of high quality iron ore pellets annually. The company employs 1, 550 people at Wabush and the Pointe Noire plant at Sept-Iles.Wabush Mines is an unincorporated joint venture of three companies -The Steel Company of Canada, Dominion Foundries and Steel Ltd. and the remaining 58% by the Wabush Iron Co. Ltd. Wabush Iron Co. Ltd. is in turn owned by six companies: The Youngstown Sheet & Tube Company, Inland Steel Company, Interlake Inc., Wheeling Pittsburg Steel Company, Finsider International S.A. and Pickands Mather & Company which is also managing agent.The town of Wabush is set in a remote part of Northern Canada accessible only by rail and air transportation. But this in no way has hindered the growth and development of the area. Modern housing units, shopping facilities, airport and of course, recreational facilities are all patt of every day living amenities, an accepted aprt of southern communities, but quite unique for northern isolated mining localities."

Jan 1, 1978

By T. A. Kirk

"The Linatex Dewatering System is a compact, low capital and maintenance cost matched set of processing equipment suitable for solids recovery, dewatering and desliming sand-like materials in the range 3/8"" to 325 mesh ( 1). Since its introduction to North America in the early 1970s, various elements of the system have been successfully installed in a variety of applic11tions both in Canada and the U.S.A. Examples are chosen from the coal, fine aggregates, iron ore and industrial minerals industries.II. Elements of the Linatex Solids Recovery System(A) The Linatex Separator (See Fig.I)The Linatex Separator, which is the heart of the system, is a specialized type of hydrocyclone designed to give a self regulating rope discharge product. It has the familiar cyclone geometry of cylindrical and conical section, tangential inlet, apex and vortex finder. The apex is enclosed in a unique patented automatic underflow regulator consisting of a collapsible rubber sleeve, and the overflow line is a siphon-leg, with a controlled air bleed valve. The siphon leg is adjusted so as to balance the internal negative pressure acting as a closing force on the underflow regulator against the mass of slurry pressing down on it from the cone section of the Separator. With correct adjustment the underflow regulator will close drip-tight on a water only feed. As solids accumulate in the apex of the cone the weight of solids counterbalances the vacuum and cat1ses the underflow regulator to open and discharge classified material at a controlled density."

Jan 1, 1978