Search Documents

By R. Maddin, W. R. Hibbard

A series of X ray experiments conducted by G. I. Taylor' in 1927 and later substantiated in 1939 by J. A. Collins2 both on axially strained aluminum single crystals, revealed evidence that during single slip crystallite rotation occurs in such a manner that " all parts of the material rotated about the transverse direction in the plane of slip."l The actual method of preparing the specimens for X ray examination is not discussed in detail by Taylor except to say that "this specimen was cut parallel to the plane of slip, as calculated from measurements of marks in the surface of the specimen. It was ground and etched till the effect of the new cuts had disappeared. This was verified by applying the same treatment to an un-distorted specimen. The X ray reflectionsl in this case were perfect ones."' Collins, on the other hand, cut his crystals in a mechanical shaper. These surfaces were polished on No. 1, No. 1/0, No. 2/0 and No. 3/0 papers and on a broadcloth lap using No. 600 alundum as a polishing medium. "Finally, the surface was deeply etched in Tucker's reagent. An unde-formed crystal was prepared in the manner described and X rayed to determine whether or not the machining and polishing operations had produced any strain or distortion in the crystal. The Laue spots all seem to be sharp, free from tails and streaks indicating no detectable strains had been introduced in the crystals." Taylor's X ray technique involved the use of "homogeneous X rays from an iron anti-cathode"; whereas Collins used Ka radiation of copper at 31kv and 20 milliamperes. Glancing angle X ray photograms were taken (1) with the axis of rotation of the spectrometer table in the plane of slip and at right angles to the slip direction, and (2) with the axis of the spectrometer table lying along the slip direction. However, eight minute exposures were used in each case and the angle setting of the spectrometer table was increased by one degree for each exposure. With the discovery of the action of three slip systems3 in the plastic deformation of single crystalline alpha brass where, formerly, only one had

Jan 1, 1950

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

By R. P. Carreker, J. C. Fisher

Cheep tests are normally constant load tests. Such tests approximate some types of service conditions and therefore are justified from the engineering point of view. Coupled with this consideration is the advantage of simplicity inherent in constant load tests, as contrasted with the comparatively complex requirements of a constant stress test. It is not surprising that the vast majority of creep tests reported are of the constant load type. Despite the enormous amount of accumulated creep test data, plastic flow is by no means completely understood. The widespread use of constant load tests is at least partly responsible for this lack of understanding. Any attempt to analyze deformation must involve the more fundamental quantity stress, rather than load. It is possible to predict constant load behavior from known constant stress data, but the reverse is much more difficult. When a metal specimen elongates, as in a creep test, the cross section decreases, maintaining constant volume. Thus For a constant stress test the force on the specimen must be decreased as the cross section decreases, that is, this force must be inversely proportional to the elongation of the specimen. An-drade has described three methods of obtaining the constant stress condition,l-3 each of which is relatively complex. The most recent proposal,³ suggests a major simplification which maintains the simplicity of the constant load test while approximating quite closely the desirable condition of constant stress. Andrade's device is admittedly more accurate but the method described below has definite advantages Consider a specimen in the form of a "V" supported at its ends. If a weight be applied at the vertex of the angle, the stress in each leg of the "V" If this stress causes an elongation ?1 in each leg of the "V," the angle decreases from a. to a smaller angle a1. The quantity sec — thus decreases with specimen elongation while the quantity 1/A increases. By selecting proper initial conditions it should be possible to hold S/So very nearly constant at unity. The proper initial conditions are realized when a0 is made equal to approximately 90°. Fig 1 compares the ratios of S/S0 for a0 = 85, 90, 95, 100°, with a0 = 0, that is, a straight speci- men, for true strains up to e = 0.10. It may prove convenient to measure X, the movement of the vertex, rather than the true elongation 1. Contour lines of X/lo are also plotted in Fig 1. The method for obtaining constant stress described above is especially suited to the testing of small wires, but may easily be extended to rods of any diameter through the use of a suitable grip which serves as the vertex joining two identical rods forming the legs of the "V." References 1. E. N. da C. Andrade: On the Viscous Flow in Metals, and Allied Phenomena. Proc. Roy. Soc., A, 84, 1, (1910-11). 2. E. N. da C. Andrade and B. Chalmers: The Resistivity of Polycrystalline Wires in Relation to Plastic Deformation, and the Mechanism of Plastic Flow. Proc. Roy. Soc., A, 138, 348, (1932). 3. E. N. da C. Andrade: A New Device for Maintaining Constant Stress in a Rod Undergoing Plastic Extension. Proc. Phys. Soc., 60, (3). 304, (March, 1948).

Jan 1, 1950

The greatest single obstacle in the path of constructive action in making conservation a reality is the inherent discord in the hearts of men. A perfect society doubtless is many millenniums removed from the present generation, but it must be admitted that progress toward a conservative use of our natural heritage with the altruistic concept of the greatest good for the greatest number for the greatest time can be attained only by a society in which discord is reduced to a minimum compatible with the limitations of human nature. Daily industrial discord is witnessed between management and labor which passes the bounds of arbitration and results in stoppages of production, waste of productive capacity, idle capital, idle labor, and the complete loss of the most unrecoverable element of all-time. The conservation of material things cannot progress independently of the conservation of the efforts of the human worker, and the results of these efforts are proportional to life itself as measured in hours and years. Unfortunately discord passes international boundaries, and the story of war is as old as the story of mankind. Our recent attempts of international control of nations appear to be dismal failures. The prestige and power of the League of Nations and the present United Nations declined rapidly after they were unsuccessful in stopping the first outbreak of hostilities after their or-

Jan 1, 1950

By G. H. Anderson

Cadmium-coppeR precipitate, a byproduct of the purification stage of the zinc plant, is composed mainly of zinc, cadmium and copper in varying amounts depending on the efficiency of precipitation and the cadmium and copper contents of the impure solution treated. The composition range is approximately: cadmium 10-12 pct, copper 6-8 pct, and zinc 3&35 pct. As received at the cadmium plant, the precipitate is a dark gray to black press cake produced by filter pressing the flocculent cadmium-copper precipitate formed when impure zinc solution is agitated with zinc dust. The details of the cadmium-copper precipitation are to be found in the paper "Electrolytic Zinc at Risdon, Tasmania," by W. C. Snow. Transactions AIME, 121, 501. The treatment, in addition to recovering cadmium as metal, yields a copper product as a residue for realization and recovers in solution for return to the zinc plant, the excess of zinc dust used during purification. The recovery of cadmium metal is approximately 200 tons† per year, but, with the amount of copper residue recovered, varies with the zinc production tonnage, composition of the original concentrates, degree of roasting and other operational factors. The operations involved in the recovery of the foregoing materials are carried out in a building adjacent to the purification section of the zinc plant and can best be described by dividing the process into the following stages: 1. Oxidation and Grinding of the cadmium-copper precipitate. 2. Leaching and Filtering. 3. Precipitation of cadmium. 4. Oxidation and Grinding of the precipitated cadmium. 5. Leaching oxidized cadmium precipitate and Purification of leach solution. 6. Electrolysis. 7. Melting, Casting and Packing. A feature of the process is the use of two distinct solution circuits. Spent electrolyte from the zinc plant circuit containing about 10 pct sulphuric acid is used as the primary solvent of the cadmium and zinc present in the oxidized precipitate. When the cadmium is later separated by precipitation and filtering, the filtrate, originally zinc plant spent electrolyte and now fortified in zinc, is returned to the zinc plant. The precipitated cadmium, after oxidation, is redissolved in spent electrolyte from cadmium electrolysis which solution is in closed circuit within the cadmium plant except for discards to the zinc plant circuit as mentioned in Section 5 hereinafter. (Fig 1.) Details of the various operations follow. I. Oxidation and Grinding of the Cadminm-copper Precipitate The precipitate having had a preliminary drying by compressed air in Dehne filter presses in the zinc plant is trucked to a storage platform of sufiicient length to store 3 to 4 days' production separately. After 48 hr exposure to atmosphere, oxidation is sufficient to enable all cadmium and zinc but only a portion of the copper to be dissolved in dilute sulphuric acid. The oxidized precipitate is shovelled into trucks and, after weighing and sampling, is broken in size by means of

Jan 1, 1950

By G. Carman Ridland

Front Range, Colorado: The majority of the rocks comprising the Front Range of Colorado are pre- Cambrian schists, gneisses, and intrusives which have been elevated to form part of the Southern Rocky Mountain physiographic province. The region is noted mainly for its production of gold and silver, but ores of tungsten, fluorspar, uranium, copper, and iron have been worked. Geological literature describes pitchblende and other radioactive minerals occurring at Jamestown, Boulder County; Central City, Gilpin County; and Lawson, Clear Creek County (fig. 1). These three adjoining counties cover most of the highly mineralized section of the Front Range which extends from James- town to Breckenridge. As far as the writer is aware, uranium has been found only in the portion north-east of Lawson.

Jan 1, 1950

By Herbert Clark Hoover, Lou Henry Hoover

PREVIOUSLY I have dealt with the methods of separating silver from copper. There now remains the portion which treats of solidified juices ; and whereas they might be considered as alien to things metallic, nevertheless, the reasons why they should not be separated from it I have explained in the second book. Solidified juices are either prepared from waters in which nature or art has infused them, or they are produced from the liquid juices themselves, or from stony minerals. Sagacious people, at first observing the waters of some lakes to be naturally full of juices which thickened on being dried up by the heat of the sun and thus became solidified juices, drew such waters into other places, or diverted them into low-lying places adjoining hills, so that the heat of the sun should likewise cause them to condense. Subsequently, because they observed that in this wise the solidified juices could be made only in summer, and then not in all countries, but only in hot and temperate regions in which it seldom rains in summer, they boiled them in vessels over a fire until they began to thicken. In this manner, at all times of the year, in all regions, even the coldest, solidified juices could be obtained from solutions of such juices, whether made by nature or by art. Afterward, when they saw juices drip from some roasted stones, they cooked these in pots in order to obtain solidified juices in this wise also. It is worth the trouble to learn the pro- portions and the methods by which these are made. I will therefore began with salt, which is made from water either salty by nature, or by the labour of man, or else from a solution of salt, or from lye, likewise salty. Water which is salty by nature, is condensed and converted into salt in salt-pits by the heat of the sun, or else by the heat of a fire in pans or pts or trenches. That which is made salty by art, is also condensed by fire and changed into salt. There should be as many salt-pits dug as the circumstance of the place permits, but there should not be more made than can be used, although we ought to make as much salt as we can sell. The depth of salt-pits should be moderate, and the bottom should be level, so that all the water is evaporated from the salt by the heat of the sun. The salt-pits should first be encrusted with salt, so that they may not suck up the water. The method of pouring or leading sea-water into salt-pits is very old, and is still in use in many places. The method is not less old, but less common, to pour well-water into salt-pits, as was done in Babylon, for which Pliny is the authority, and in Cappadocia, where they used not only well-water, but also spring-water. In all hot countries salt-water and lake-water are conducted, poured or carried into salt-pits, and, being dried by the heat of the sun, are converted into

Jan 1, 1950

By Herbert Clark Hoover, Lou Henry Hoover

QUESTIONS of assaying were explained in the last Book, and I have now come to a greater task, that is, to the description of how we extract the metals. First of all I will explain the method of preparing the ore1 ; for since Nature usually creates metals in an impure state, mixed with earth, stones, and solidified juices, it is necessary to separate most of these impurities from the ores as far as can be, before they are smelted, and therefore I will now describe the methods by which the ores are sorted, broken with hammers, burnt, crushed with stamps, ground into powder, sifted, washed, roasted, and calcineda.

Jan 1, 1950

By John S. Johnson, Thomas Fraser

SIZING is the process of separating mixed particles into groups of particles all of the same size, or into groups in which all particles range between certain definite maximum and minimum sizes. In coal preparation, sizing is generally accomplished by passing the coal over screens. Separation by differential settling in air or water currents has been adapted to the special field of separating very fine sizes, and these processes are in commercial use to a relatively small extent in the coal industry. Separation with screens is a very old industrial practice. Agricola described the use of screens for ore treatment in the middle ages. In the literature of the British coal industry references were made to the screening of coal as early as 1589, but the practice of extensive sizing for the market did not become general until the last half of the nineteenth century. In America, the practice of sizing developed first in the Pennsylvania anthracite region, beginning with the use of rakes in the mine working places to recover coarse coal. This mining procedure left the fines in the mine. Preparation outside the mine started with the installation of stationary cast-iron plates with 4 to 6-in. square holes. The run-of-mine coal was dumped upon the platforms, the large pieces of rock were picked out by hand, and the large lumps of coal were broken with hammers. The term "breaker," which still applies to the anthracite-preparation plant, originated with this practice, but the term is no longer descriptive of the entire function of the plant. In 1884, the first power-operated anthracite coal breaker was erected by Gideon Bart at his colliery at Wolf Creek near Minersville, Pa. This plant utilized a system of rolls for breaking the coal and revolving screens for sizing. The plant was driven by a steam engine. It could handle coal at the rate of 200 tons a day. By 1860, revolving screens were in wide use in the Pennsylvania anthracite field. Shaking screens were introduced in the Pennsylvania anthracite region in the 90's and they rapidly displaced the lower-capacity revolving screens.

Jan 1, 1950

By E. M. Cox, A. S. Skapski, N. H. Nachtrieb, M. C. Bachelder

D. T. ROGERS*—The conclusions drawn in this paper have important practical significance to the steelmaker and the metallurgist if, in practice, it is demonstrated that metallic copper in the charge will pick up sulphur from the furnace atmosphere and thus increase the sulphur content of the bath. The problem of residual copper arising out of increasing copper in the scrap available to the industry is, in itself, a matter of concern to the steel maker. If, in addition to the often detrimental effects of high residual copper upon the physical properties of some important steel grades, there is to be a complication of the sulphur problem, then we have a set of conditions that bodes no good for the open hearth melter and the open hearth metallurgist. M. B. BEVER*— Investigations of gas-metal equilibria continue to be of interest, especially as new possibilities for improving experimental techniques emerge. Higher purity of reacting substances, better refractories, improved methods of temperature control and an increased awareness of the pitfalls of high-temperature equilibrium work are

Jan 1, 1950

By I. C. Brown, J. F. Henderson

"IntroductionThe Yellowknife greenstone belt lies along the west side of Yellowknife bay on the north shore of Great Slave lake, some 600 miles north of Edmonton, Alberta. The producing gold mines along the belt include the Con-Rycon and Negus which came into production in 1938 and 1939, and the Giant Yellowknife, which followed in 1948. In addition to these, the Akaitcho and Crestaurum mines are potential producers and there are several promising prospects.Early geological work along the belt was done by A. W. Jolliffe who first recognized a number of great faults, the largest of which is the West Bay fault with a horizontal movement of more than 3 miles. In 1943, A. S. Dadson, following an examination of the Giant-Yellowknife property, advanced the hypothesis that Baker Creek valley was underlain by a series of major gold-bearing shear zones. Subsequent diamond drilling in 1944 bore out the correctness of this view and outlined the great ore-bearing shear zones that are now being developed and mined by Giant Yellowknife Gold Mines. Near the south boundary of the Giant property, the shear zones are cut off by the West Bay fault. This prompted Neil Campbell, District Geologist for the Consolidated Mining and Smelting Company, to make a detailed study of the geology along the West Bay fault in the hope of finding the faulted extension of the Giant shear-zone system on the west side of this fault. In this he was entirely successful. By careful geological mapping he matched several faulted diabase dykes on both sides of the fault and, knowing their dip, determined the horizontal and vertical components of movement along the fault. Subsequent •diamond drilling based on Campbell's work located the presumed correlative of the Giant shear-zone system on the Con-Rycon and Negus properties, where it has been named the Campbell zone or system. At the present time, all production at the Negus Mines property is coming from orebodies along the Campbell zone."

Jan 1, 1950

By M. L. Haider

Introduction I Appreciate very much the opportunity of discussing with you tonight oil developments in western Canada. These developments are of importance to all of us, first because of their great economic significance to all of Canada, and second because of the location of the new oilfields. Situated as they are in the west and northwest, they are of considerable strategic value from the standpoint of continental defence. The story of oil development in Canada covers a span of almost a century, during which time success in finding reserves of petroleum was barely sufficient to maintain interest in continuing the search. Finally, in 1947, a well of the first importance was completed in Alberta and, judging by discoveries made since then, it appears that Canada, at long last, is to become an important producer of petroleum.

Jan 1, 1950

By E. D. Gardner

The tide of increasing demand for metals turned during early 1949, with resultant lower prices. The production of the principal metals was less than in 1948. The problem of high unit costs, however, was held over from 1948. With the lower prices for metals, greater efforts are being made to reduce operating costs. The labor supply was adequate during the latter half of the year in most districts. The force has been reduced at most mines; some mines were idle during part of the year because of strikes, and others ceased operations on their own account. In the main, labor efficiency increased during the year in underground metal mines. Efforts are being made generally to improve labor relations. Green men hired in the time of the scarcity of skilled miners are becoming better trained. The supervisory personnel of most mines is cost conscious, and the planning of operations has been improved. Overhead costs are being scrutinized. The trend toward mechanization underground continued strong. Mining technology rapidly is becoming a problem of handling materials. Surface miners, underground miners and miners of metals, nonmetallics, and coal can learn much Gardner from each other. A mine, however, may become overmechanized. The capital charges against new equipment may exceed the saving in labor costs where sufficient daily tonnage is not handled.

Jan 1, 1950

By Charles H. Moore, H. Sigurdson

When lime and magnesia are used as fluxes in the smelting of titaniferous ores fluid, digestible slags low in iron oxide and high in titanium dioxide are produced. The mineral phases present in such slags are (Fe,Mg)O.ZTiOp, CaTiO3, and minor amounts of silicate glass (or its devitrification products). The flux additions are added to the ore in relative amounts to crystallize a ratio of (Fe,Mg)O.2TiO2 to CaTiO, of near the eutectic proportions of 60 pct (Fe,Mg)O.2TiO2 and 40 pct CaTiOl. FeO.TiOz (ilmenite) remains present in the slag until the FeO content is reduced to approximately 8 pct. Optimum slag composition is obtained by reducing the FeO content to between 2 and 6 pct. Continued reduction shifts the (Fe,Mg)O.2TiO2 to oxygen deficient structures classified as MgTi306 and MgTi2O.. Further reduction yields titanium oxycarbides and freezes the melts. The(Fe,Mg)0.2TiO2 structure shows a complete isomorphous replacement of iron by magnesium. It also forms a solid solution compound with as high as 12 mols of TiO2 under reducing conditions without the occurrence of rutile or reduced titanium oxides in the slag.

Jan 1, 1950

Mother Earth has had a long life extending over two billion years, during which time she has changed from a mass of incandescent gases to her present form, exhibiting a density stratification from the extremely tenuous gases of the stratosphere to the heavy central nickeliron core. Man is now mining all the principal divisions of Mother Earth except the centrosphere. Nitrogen, oxygen, neon, and other rarer gases are being recovered from the air; magnesium, bromium, potash, borates, and other salts from lakes and seas; brines, medicinal mineral waters, and great quantities of water for domestic and industrial uses from surface and subsurface reservoirs; and, from the rocky crust, many minerals and fuels for our present industrial civilization as well as plants and animals for food and shelter. Productivity of soil is influenced both positively and negatively by man. There is some cause to bewail what may be considered a wasteful influence of men on soil. The general situation is bad in spots but not hopeless. The passing of large areas of fertile land in some areas is merely to be noted and not to be mourned. These lands could not have been used without decrease in their fertility. The productivity factor is affected by human activities. Many soils in the eastern and southern states are far richer and more productive now than they were at any previous time. Arctic soils are not productive

Jan 1, 1950

By Russell G. Haworth

Three companies, United States Potash Company, Potash Company of America, and International Minerals and Chemical Corporation, are now operating potash mines and reGneries in the Carlsbad, New Mexico, area. The three mines are located approximately twenty miles east of Car1sbad. The deposits have been found ideal for mechanized mining methods. This summary has been compiled from information made available by the three operating companies. Prospecting Since outcrops of potash are nonexistent, prospecting is accomplished by drilling and coring of the salt section to establish the grade, thickness, and outline of the potash beds contained in the salt deposits. Information regarding the nature of the formations in the cover of 400 to 600 ft thick over the salt and potash beds is also obtained from drill cuttings in the same operation. By proper interpretation of assembled data the best location for shafts may be determined. The overburden varies in character but consists in general of interbedded shales, sand, gravels, limestones, and anhydrite beds. Water, in unpleasant quantities, especially in the sands and limestones, often completes the geologic section. Some of the shaftas in the area have been sunk without undue difficulties, others have been delayed by flows of water. Most of the shafts are concreted from the surface to the salt section. Each of the three mines in the Carlsbad area has one shaft for hoisting ore and one for hoisting men and supplies. Mining Methods Information acquired from initial drilling and prospecting affected the choice of mining methods. Since the tabular, slightly rolling deposits were similar to coal seams, the room-and-pillar system used in coal mining was adopted by all the companies. Pillars have not been removed in any of the mines on a large scale. One company has conducted experimental robbing of pillars in one restricted area. Where it is known that overlying strata contain water in large amounts, it is not considered practical to risk flooding of the mines by removing pillars without fill. Some thought is now being directed toward development of economical methods of filling for pillar recovery. The problem is not identical at the three mines and local conditions will govern the methods employed for eventual pillar recovery. The important point is that, with large reserves, it has not been necessary to resort to mining of pillars for adequate production. The ore deposits are laterally extensive but are irregular in shape and lie at a depth of 700 to 1100 ft below the surface. The major operations of all mines are on the same bed strati-graphically, except for the langbeinite level at International Minerals and Chemical Corporation. The deposits are apparently not connected and in many parts of the deposits being mined, "salt horses" or barren zones occur. From 400 to 700 ft of salt with minor beds of polyhalite and anhydrite lie immediately above the ore horizon. The ore differs from the salt only in the potassium chloride content and color due to small amounts of iron associated with the sylvite, giving the ore a somewhat mottled red and white cast. Thickness of the ore varies from 5 to 14 ft. Rooms and break-throughs in the mines vary from 24 to 40 ft in width, the overlying salt forming an excellent roof and providing safe mining conditions. Almost no timber is used in any of the mines for roof support. Drilling is normally the first step in mining the face of a room. Electric motor driven auger drills are used in the area. Jack hammers were used to some extent when the mines were first opened but the ore is easily drilled if bits are sharp and the coal type

Jan 1, 1950

By P. R. Sperry, P. A. Beck, J. Towers

Dahl and Pawlek1 found that electrolytic copper develops extremely coarse grains at 1000°C after about 90 pct reduction by rolling. This coarsening occurs only under conditions of penultimate grain size, deformation, and alloying which lead to the "cube" recrystallization texture.l,2,3,5 The peculiar angular shapes and straight grain boundaries of the coarse grains were noted by several investigator.1,4,5 On the other hand, coarsening in Fe-containing aluminum or in AI-Mn alloys8 does not depend on a "cube" (or any well developed) recrystallization texture. It is true that increasing deformation by rolling, and, therefore, an increasingly well developed re-crystallization texture, are associated with decreasing incubation periods of coarsening.6-7-8 Nevertheless, coarsening readily develops in aluminum even after only 30 pct reduction by rolling, where the recrystallization texture is very weak.6,8 Also, coarsening was observed by Jeffries9 many years ago in sintered thoriated tungsten, which presumably has no preferred orientation. In all these cases coarsening is associated with grain growth inhibition by a dispersed second phase.8,9 The annealing temperature has to be suficiently high to overcome the inhibition at a few locations. But if it is too high, growth starts at many points, and the resulting grain size becomes much smaller.9 Normally, the coarse grains are more or less equiaxed, and the boundaries have a typical ragged appearance.6.8 Cook and Macquarie4 demonstrated that, in addition to the texture-dependent coarsening previously found at 1000°C,l electrolytic tough pitch copper may also coarsen at 800°C after 50 pct reduction by cross rolling. The coarse grains formed under such conditions have rounded shapes and ragged boundaries, like those in aluminum. When the annealing temperature is higher, the tendency for their formation decreases. All these observations suggest that the coarsening at 800°C is associated with inhibition by a second phase. Actually, coarsening at 800°C after 50 pct reduction by cross rolling was observed only in tough pitch copper,4 which contains Cu2O particles. On the other hand, the texture-dependent 1000°C coarsening occurs in both tough pitch and oxygen-free copper;4 it does not appear to depend on the presence of a dispersed second phase. However, the interpretation of the 800°C coarsening in Cu after 50 pct rolling as an inhibition-dependent process, similar to the coarsening in A1-Mn alloys, is somewhat weakened by the fact that this coarsening was reported4 to occur only after cross rolling, and not after straight rolling. It was, therefore, decided to re-examine this question. A 1 in. diam electrolytic tough pitch copper rod, No. 2 hard drawn, was annealed for 20 min at 700°C, rolled to 0.5 in., annealed 10 min at 700°C, and straight rolled to 0.064 in. It was then given a penultimate anneal of 20 min at 500°C and it was cut into four sections, which were given final reductions by straight rolling as follows: A 30 pct reduction of area B 50 pct reduction of area C 70 pct reduction of area D 90 pct reduction of area Specimens cut from the four sections were finally annealed at 800°C in an oxidizing atmosphere. Strip A remained fine grained up to 10 hr, but the specimen annealed 12 hr consisted of only 2 large grains. Strip B had a few scattered large (1/2 to 3/4 mm) grains after 1 min, although the balance of the specimen consisted of fine grains of about 0.02 mm. After 5 min there were several 10 to 15 mm grains present, and after 1 hr strip B was completely coarsened. The coarse grains had the same characteristics (see Fig 1) as those obtained by Cook and Macquarie at 800°C after cross rolling. Strip C had several grains of 0.05 to 1 mm after 1 min, but it was still largely fine grained after 12 hr. After 48 hr it consisted entirely of grains of about 0.5 to 4 mm, with an extraordinarily large number of twin bands. Strip D remained com- pletely fine grained after 4 hr at 800°C. These results indicate that, in the deformation range of 30 to 70 pct reduction, the incubation period for coarsening as well as the rate of growth and the final size of the coarse grains decreases with increasing deformation. Similar

Jan 1, 1950

By Bernard Greifer, Walter Rose

The purpose of this note is to call attention to a source of difficulty which can be responsible for inaccurate estimates of wetting liquid pressure gradients in mixture flow experiments of the Hassler1 type. It has been our experience occasionally to observe what were indicated to be negative pressure gradients, and these were regarded as anomalous in the sense that physically they seemed to contradict the requirement that the flux be in the direction of the potential field. At first it was thought that our scheme of assembling barriers and core sample led to such asymmetry in the distribution of isobars that the manometric leads at each end of the core were responding to internal pressures (within the core sample) which could be either positive or negative with respect to each other, and which in fact might tend to reflect on different effective core lengths in an unpredictable fashion as the wetting liquid saturation was changed. However, no compelling evidence of this possibility has been established. In addition, we were cognizant of the requirements to be satisfied in selecting manometric instrumentation to minimize the delay in response of the manometer to the differential pressures being measured, and were thus assured that our observations of anomalous pressure gradients could not be explained by faulty instrumentation. What we suggest is that if a leak sink occurs in the fluid lines connecting the core to either side of the differential manometer, errors exceeding 100 per cent may result in the estimation of wetting liquid pressure gradient, even though the leak is of such small magnitude that its existence would tend to be obscured by evaporation effects. This is because in a system with leaks at the specified places, the manometer rec- ords at steady state the pressure drop across the manometer barrier elements in addition to the pressure drop across the core sample. This possibility will be illustrated below analytically and by numerical example for the special case where the leak occurs on the high presure side of the core, since we are especially desirous to explain the significance of our observations of the so-called negative pressure gradients. It will be indicated, however, that leak sinks on the low pressure side of the core can account for observations of anomalously high values of pressure gradient, and that multiple leaks on both sides of the core can provide for some compensation so that the errors in pressure estimation are reduced. However, the major point to be emphasized is the fact that the impractical-ity of detecting the small leak sinks which give rise to the difficulties makes it a complicated task for the experimenter in a particular case to know with certainty that his estimation of pressure gradient lies within the limits of error which can be tolerated. Fig. 1 shows the electrical analog of the flow system we have employed in our studies. The inflow and outflow barriers. Rbl and Rb2, the manometer barriers, Rm1, and Rm2, and the core sample, Rc— for a particular fluid saturation and distribution— are all designated as resistance elements; the flowmeter is designated by an ammeter, A; the pressure source is designated by E; and the manometric device is designated by the voltmeter, V. Included in the circuit are the variable resistances, Rx and Ry, which may be regarded as the leak sinks, and which, in general, can vary in magnitude from zero (i.e., a large hole or shunt in the system) to infinity (i.e., no

Jan 1, 1950

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and' regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By T. C. Russell

The Conda phosphate mine, eight miles north of Soda Springs in Caribou County, Idaho, was opened up by the Anaconda Copper Mining CO. in 1920. Except for brief periods, during the 20's and early 30's, the mine has maintained a continuous production, and 2,100,000 short tons of phosphate rock have been shipped to the company's phosphate fertilizer manufacturing plant at Anaconda, Mont., or to independent processing plants on the Pacific Coast; a small tonnage of the rock has been shipped to the Hawaiian Islands. The Phosphoria formation on the Conda property consists of two, commercial-grade phosphate beds separated by 147 ft of black to brownish colored phosphatic calcareous shales interbedded with softer mudstones, clays, and occasional narrow seams of oolitic phosphate. The main lower phosphate bed in the series averaging 7.1 ft in thickness, is called the "foot-wall bed," which lies coriformably on the Wells limestone formation, the 1atter often containing irregular bands of chert. The upper or " hanging-wall bed" of phosphate rock averaging 7.2 ft in thickness, is overlaid by thick quartzite beds, locally called the " Rex chert" member in the upper portion of the Phosphoria formation. (Fig 1.) There are two anticlines on the property with axis striking approximately parallel to the mountain range beneath which extensive development on phosphate rock has been conducted in the past, and is now in progress. The phosphate beds have been eroded to a large extent from the tops of these anticlines, leaving at least three well-pronounced outcrops of the phosphate beds exposed within the boundaries of the Anaconda Copper Mining Cornpany's properties. At present, mining operations in the Conda No. 3 mine are confined to the two phosphate beds along the east flank of the easternmost anticline, where the dips on the beds vary from 50° to 60° east, thereby affording favorable conditions for the sublevel mining system now in use. Mining operations formerly were confined to the footwall or lower oolitic phosphate bed because of its higher phosphate and vanadium contents (32 pct P²O5 and 0.29 pct V2 O 5); this bed averages 7.1 ft in thickness. The oolitic portions of the upper bed were of satisfactory grade, but the shale and clay partings (Fig 2) diluted the mined rock and could not he separated economically by selective mining or by sorting. Experiments in beneficiating this rock were carried on for a number of years. Recently, a simple washing process was adopted, which gave a satisfactory grade of concentrates and a high recovery of P² O5. In 1947 it was decided to expand Anaconda's production of treble superphosphate and phosphoric acid by approximately 90 pct. This rock will be obtained from the footwall and hanging-wall beds, and the rock from the hanging-wall bed will be benefici-ated at -Anaconda.l In order to take advantage of the previous development on the 500 secondary haulage level, short crosscuts will be driven at approximately 950 ft intervals from the existing lateral drifts through the hanging-wall shale beds. From the inner end of each crosscut, short lateral drifts will he driven in both directions, so that four working raises can he put up on the dip of the phosphate bed at proper intervals along each of the lateral drifts. The mining operation on the footwall bed at Conda

Jan 1, 1950