Search Documents

By W. L. Dennen, V. H. Wilson

This paper is a description of the opera-tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery 01 The Hudson Coal Co. during the first nine months of operation and follows a preliminary description given at the .Institute cite Institute in May, 1947, in a paper titled "Preparation of Anthracite Silt for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size op-erating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig I and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which han-dles the Breaker waste water. This under-flow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped to vibrating screens where the plus 3/16-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine tipple for re-preparation.

Jan 1, 1949

By E. C. Bitzer

The primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high- grade heavy sink product. It appears from this last work that the new separator has definite mechanical and metalluigical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator has required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent development of the inverted or closed-top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1949

amounted to about 2000 metric tons. The total output is increasing from year to year. Marine salt is now produced in Haiti in quantity sufficient to supply nearly all the requirements of this Republic, so production tax is now collected. Central America Guatemala-The major production of salt in Guatemala is solar salt derived from sea water, but the Indian population prefers salt derived by boiling coastal marine earth. Salt is taxed by the Government. The industry has been beset by controversies in recent years, especially following the revolution of October 1944. The Government issued a decree in August 1940 designed to control production and price of salt. The creation of a salt consortium was provided for and marketing was to be governed by production quotas. It is understood that the Government pool was later dissolved and the industry is now under older laws whereby production and sales have no limits. South America Panama-Output of salt in Panama in a very recent year was 11,000 net tons of solar-evaporated sea salt. A Government bank is in charge of output and distribution of the product. Colombia-Rock-salt deposits are known in five places-Zipaquira, Nemocon, and Sesquile, in the Department of Cundinamarca, the Cumural y Upin near Restrepo, and San Miguel y Barital, near Medina in Meta Intendency. The latter deposit never has been worked on account of its inaccessibility. Saline springs are worked in four locations. The largest producer among marine salinas is Manare but it is now planned to make Bahia Honda the largest. Some evaporated salt is made in vacuum pans. The deposits at Zipaquira, Nemocon, and Sesquile are believed to occur in the domal type of deposit. All the salt resources are under Government control. Venezuela-The salt industry in Venezuela is under Government control and is taxed. Taxes in recent years, however, have been reduced for salt used in curing hides and salting meats, fish and fish products. Production has approximated 25,000 metric tons yearly but may now be considerably above that figure. The basin on the peninsula of Araya, State of Sucre, which at present is the only important source of salt, could produce at least 175,000 metric tons if more ground were provided-a larger supply than the entire country could consume. This unique landlocked basin of nearly 1000 acres lies 12 ft below sea level. Ecuador-Salt is a Government monopoly in Ecuador and is produced chiefly by solar evaporation close to the shore. The main producing center is on the Santa Elena peninsula, which supplies about 90 pct of the salt. Small fields are at Punta Arenas, Payana, and Chara-

Jan 1, 1949

By M. E. True, B. L. Stone

To cope with the problems encountered when drilling at greater depths and to reduce the amount of physical effort required on the part of drilling crews in making round trips, a new type of semiautomatic power-operated drilling machinery has been developed which permits round trips to be made without the drill pipe being touched by hand. This equipment consists of hy-draulically operated tongs which perform the stabbing, spinning, and tong-ing operations, and two power-operated racking units mounted in the derrick for carrying the pipe to and from the center of the hole and positioning it on the mat and in the rack. With this equipment all of the operations of the various units are controlled remotely by manipulation of hydraulic valve levers and electric switches. INTRODUCTION As horsepower rises to meet the demand for deeper drilling, it is necessary to increase the weight of surface drilling equipment. Also, the duration of repetitive operations in making round trips to change bits is greatly increased with depth. Harder formations encountered at greater depths reduce bit life rapidly, resulting in more frequent round trips and in some instances more time is consumed in changing bits than in drilling. Since the introduction of the first rotary employed to drill for oil in 18951, there has been relatively little change in the general procedure for making up, breaking out, stabbing, and racking drill pipe in making round trips to change bits. The conventional method of making round trips with the drill pipe requires that drilling crews lend strenuous physical assistance to manually operated tools. Although many new devices have been developed to improve efficiency, increase speed of making round trips, improve safety, and reduce the amount of physical effort required in handling drill pipe, it is considered a vital necessity to substitute automatic or semiautomatic power-operated machinery for many of our more or less manual operations if extremely deep drilling is to be carried out successfully on a production basis in the same manner as our shallower drilling of today. Field tests have been made of remotely controlled power-operated tongs, spinner, stabber, and racking equipment. The tongs, which include a built-in pipe spinner, are mounted on a column, are capable of gripping and supporting the weight of a 90-foot stand of drill pipe, and are provided with means for moving the pipe vertically as well as to and from the center of the hole. The racking equipment consists of two units, one at the level of the conventional monkey board and the other at the first girth on the ladder side of the derrick. Most of the physical effort of making round trips with drill pipe has been eliminated in that all of the operations of tonging, spinning, stabbing, and racking of pipe on the floor are controlled by an operator in a seated position by manipulation of hydraulic and electric valve levers and buttons. The driller is relieved of operating the cathead, leaving only the hoisting and slips to be controlled. Complete round trips are made without the drill pipe being touched by the drilling crews. Although the speed of pulling or running a single stand with the power-operated equipment is approximately the same as that with conventional equipment, it is possible to maintain this rate for long periods, whereas fatigue slows crews working conventionally during round trips, especially under adverse weather. After completing round trips with this equipment, drilling crews are not exhausted, consequently, are able to perform effectively their duties while drilling, which is essential for maximum over-all efficiency. Safety is substantially improved as the derrickman performs his duties from a platform enclosed by rails and the tong lines and spinning chain are eliminated from the derrick floor. The hazards encountered in racking drill pipe on the floor and in stabbing are also eliminated. Figure 1 shows a drawing of a derrick equipped with the power-operated drill'pipe handling equipment.

Jan 1, 1949

By Henry T. Mudd

FLUORSPAR is a nonmetallic mineral aggregate or mass containing a sufficient quantity of fluorite (CaF2) to be of commercial interest. It has only moderate value per unit of weight and its cost as a percentage of the cost of finished consumer products is nearly negligible. Nevertheless, it has wide and great industrial importance. In periods of national emergency it is a mineral without which many very necessary manufacturing processes would be greatly handicapped; a few could not exist. Fluorite contains 51.1 pct calcium and 48.9 pct fluorine. Industrial grades of fluorspar prepared for the consumer normally contain from 85 to 98 pct fluorite, depending on the use. The ores may contain as little as 30 pct fluorite, depending on many factors such as accessibility to transportation and markets, character of ore, and prices. Fluorite is a lustrous, glasslike mineral, generally translucent to transparent; it may be clear and colorless or range in color from slightly bluish through various shades of violet, amethyst, purple, green, and yellow. It crystallizes in the isometric system and possesses perfect octahedral cleavage. Commonly it occurs in masses of very pure crystal- line material with aggregates of cubical crystals in open spaces, but - it is also found in fine to coarse granular form. Banded veins and masses with fibrous, radiating structure occur locally. It is usually found associated more or less intimately with other minerals and rocks, from which it must be separated for commercial use. The specific gravity of fluorite is 3.18 and the hardness is 4 in the Mohs scale, compared with 7 for quartz and 3 for calcite. It is distinguished from calcite by its failure to effervesce with dilute hydrochloric acid. Heated with sulphuric acid, it gives off fumes of hydro- fluoric acid, which etch glass.22,25,33.34,35.41

Jan 1, 1949

By McMillan W. D.

Vermiculite is the name of a group of micaceous minerals characterized by their property of exfoliating when heated and thereby increasing many times their original volume. The resulting product has excellent heat-and sound-insulating properties, is used as a lightweight aggregate, and has numerous other industrial applications. Deposits of vermiculite occur in areas of pre-Cambrian rocks of the Llano uplift of central Texas, particularly in Burnet and Llano Counties. Because of the growing economic importance of vermiculite products, the Bureau of Mines undertook a detailed investigation of several deposits in Llano County. This investigation was completed in February 1947. The work comprised topographic surveys of five deposits, drilling with a 4-1/4 inch Parmanco power auger drill, and laboratory evaluation of samples. 342 drill holes, aggregating 4,905.5 feet, were completed, and 377 samples were taken. Laboratory evaluation of the vermiculite comprised expansion tests on both crude and beneficiated samples. The products obtained were compared with commercial-grade vermiculite from Montana.

Jan 1, 1949

By W. M. Traver

During World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for exploration included those expected to contain metals of importance in the successful prosecution of the war. This report describes exploration of a district of known antimony occurrence on Coyote or Antimony Creek near Antimony, Garfield County, Utah. A preliminary report by Paul T. Allsman, Chief of the Bureau's Salt Lake City branch made in August 1941, recommended further investigation, and proposed methods for performing the work. The project, begun in November 1941 and completed in January 1942, included trenching and sampling in four of the most promising parts of the area The Federal Geological Survey cooperated in the work by detailed mapping and assisted in the interpretation of geologic data.

Jan 1, 1949

By E. P. Barret

Differences in the reducibility of iron oxide materials have been recognized for a long time. Limonites are deoxidized more readily than hematites, and unaltered magnetites are the most difficult to deoxidize. Sinters are found between hematites and magnetites and vary considerably in reducibility, depending on the sintering practice followed and on the degree of fusion of the product. The increased activity in the beneficiation of taconite recently has made available a new blast-furnace raw material, namely, iron oxide pellets made from magnetic taconite concentrate. Many of the data in this paper apply to these pellets, or glomerules, as they were called when this method of agglomerating iron ores was first considered. To clarify the terms applied to iron oxide materials in this paper, the following definitions are given. Agglomeration is the general term applied to all methods of compacting or consolidating fine iron oxide materials. Sinter is the product from a Dwight-Lloyd or Greenawalt sintering machine. Pellets are formed by balling fine, moist oxide in a rotating drum at room temperature, followed by heating in a shaft furnace to a temperature below that of incipient fusion to develop a permanent bond. Nodules are formed by heating the iron oxide material to incipient fusion in a rotary kiln. Briquets are formed in a mold under pressure, with or without the addition of a binder, and burned to develop a permanent bond.

Jan 1, 1949

By D. Turnbull, J. H. Hollomon, J. C. Fisher

The concepts of nucleation and of growth have adequately described the isothermal phase transformations to which they have been applied.ls2 However, these concepts have not yet been used successfully to describe the kinetics of a number of transformations that are not observed to take place isothermally. A typical reaction of this type is the austenite to martensite transformation in steels, for which the new phase appears only during cooling of the parent phase. If the cooling is interrupted, transformation ceases; yet had the cooling continued, transformation would also have continued. Nuclei of a new phase do not leap into existence all at once by the simultaneous cooperation of a large number of atoms or molecules of the parent phase; rather they are formed at finite rates by gaining or losing atoms one at a time from the surrounding materiaL3,4 Further thermo-dynamic considerations require a finite concentration of small transitory nuclei of all unstable phases to exist at equilibrium in a stable phase.= For steel in particular, nuclei of ferrite (a iron) exist at equilibrium in austenite (y iron) at temperatures where austenite is the stable phase. If a high-temperature phase a be cooled sufficiently rapidly from temperature TI above the a-ß equilibrium temperature To, to temperature T-1 below To where ß is the stable phase, the equilibrium distribution of ß nuclei corresponding to the high temperature will be retained. There are two limiting possibilities of particular interest: I. The steady state rate of nucleation of ß may be appreciable at T_1, and may require a concentration of sub-critical nuclei exceeding that retained from the high temperature. Time will be required then for the concentration of nuclei to build up to the steady state value, and an induction period will be observed during which the rate of nucleation will increase to the steady state value. 2. The steady state rate of nucleation of ß may be negligible at T-l, while the critical size for continuous growth of ß nuclei, which decreases with increased subcooling of the a phase, may reach a value so small that some. of the retained high-temperature nu-

Jan 1, 1949

By E. P. Burtchaell

A method is presented for evaluating the effect of gravity drive upon the reservoir performance of a high relief pool. Conventional forms of reservoir analysis do not consider the alterations in the basic material balance data caused by gravity segregation of reservoir fluids. A procedure is outlined for structurally weighting physical and chemical data for use in the material balance equation. It is demonstrated how actual pool performance data can be utilized to evaluate the future reservoir performance of a gravity drive pool. INTRODUCTION Conventional reservoir engineering. procedure is inadequate for the analysis of an oil pool which has considerable structural relief, steep dips, and good permeability development. In, pools of this type, gravity drainage has an important part in the movement of oil to the wells and the effects of gravity on the overall pool performance should be included in any analysis of reservoir behavior. Many engineers have the opinion that the force of gravity in the movement of oil is not important until the later life of a pool.' Probably the basis for this belief is that gravitational effects may not be readily discernible until a pool is nearing depletion. This would be especially true for pools not having a high degree of structural relief and permeability development. Actually the effects of gravitational forces are at a maximum when the pool pressure is high, for during this period the hydrostatic head of the oil column is at a maximum and the viscosity of the oil is at a minimum. Oil recoveries from pools having favorable gravity drive characteristics may equal or even exceed recoveries which might be expected from water displacement. Field evidence indicates that in some reservoirs gravity drive has resulted in recoveries greater than that which could have been expected from gas expansion or water drive.'.3 Unfortunately, the possible effects of gravity drive on pool performance have been underestimated and other reasons have been sought to explain the high recoveries obtained. There are unquestionably many reservoirs to which the principles of gravity drainage can be effectively applied. It is the purpose of this paper to illustrate one method whereby gravity drive is included in the reservoir analysis of an oil pool. A hypothetical pool, typical of many California reservoirs, is used as an example. As used in this paper, "gravity drive" is defined as the overall effect of gravitational influences on the recovery of petroleum from the reservoir; "gravitational segregation" as the gravity separation of oil and gas within the reservoir; and "gravity drainage" as the downward movement of oil as caused by the force of gravity. SAND VOLUME DATA Fig. 1 presents a structural contour map of the pool under study. Maximum closure is 1950 feet with dips on the south flank approaching 45". The original gas-oil interface was set at -5200 feet. Average thickness of the producing sand was 200 feet. For use in subsequent calculations ill this paper, the pool was subdivided into 100-foot vertical increments and the sand-volume content of each increment was obtained. If the gross sand thickness is small, under 100 feet, the sand-volume content can be obtained by superimposing an isopachous map upon a structural contour map and planimetering the average thickness of each 100-foot increment. For sand thicknesses over 100 feet, one approacli would be to construct a sufficient number of cross-sections of the pool from which the weighted sand-volume of each 100-foot increment could be obtained. Variations in the sand body with depth, as determined by core data, can also be included in the above process. Table I presents a summary of sand-volume calculations, core data, and the original distribution of reservoir hydrocarbons in the pool. Fig. 2 illustrates the structural distribution of the sand-volume content. A total of 171,398 acre-feet is contained within the productive limits of the pool. Assuming an average porosity of 25% and an interstitial water content of 20%, the original hydrocarbon content was computed to be 227,075,000 barrels. DEPTH-PRESSURE DATA The determination of the initial vertical pressure arrangement in the pool is necessary for PVT and material balance calculations. Whenever sufficient data are available, a plot of pressure versus subsea depth of measurement should be made. From this plot a representative fluid pressure gradient can be established. Lacking sufficient initial pressure data, an initial pressure gradient may he estimated or calculated from avail-

Jan 1, 1949

By T. E. Leontis

The importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication, attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne. The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Znt alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-~Zn,f Mg-jZn, Mg-4.4211, Mg-6Zn, and Mg-roZn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. Literature The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison. Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,' Dumas and Rockaert, Haugh-ton and Prytherch,6 and by Spitaler, the last being reported by Beck.' A slight superiority in the tensile strength of chill-cent Mg + 8 es alloy Over the sand-cast alloy was noted by Maybrey.8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1949

By B. C. Burgess

IN the first edition of this volume,44 feldspar was introduced as "the I commonest mineral of the crystalline rocks," usually in small grains associated with other minerals and commercially produced only from pegrnatites. Now other crystalline rocks, such as alaskites and granites, have become present or potential sources of feldspar. In addition, feldspar has encountered very vigorous competition from such substitutes as nepheline syenite and aplite. COMPOSITION AND PROPERTIES The feldspars form a group of which the principal species are orthoclase, microcline, albite, and anorthite. These are aluminum silicates of potassium, sodium and calcium. There are also a barium feldspar, celsian, and barium orthoclase feldspar, hyalophane, rarely found and of no commercial importance. None of the minerals in the feldspar group are found pure or nearly pure. The potash feldspars, orthoclase and microcline, nearly always contain some albite (soda microcline, an- orthoclase); the soda feldspars usually contain some anorthite (lime feldspar). There is a series of soda-lime feldspars known as plagioclase in which the albite and anorthite molecules replace each other in varying proportions from albite through oligoclase, andesine, labradorite, and bytownite to anorthite. Theoretical chemical composition of the principal feldspars is given in Table 1. The Whiteware Division of the American Ceramic Society sub- mitted a list of definitions of ceramic terms, in April 1947, for use in technical literature. For feldspar it gives: "A group of igneous minerals consisting chiefly of the aluminum silicates of potash, soda and lime, in which one base generally predominates." Commercial feldspars are intergrowths of at least two species of feldspar, which occur associated with one or more accessory minerals such as quartz, muscovite, biotite, garnet and tourmaline as well as with small but varying proportions of the decomposition product, kaolinite. An intergrowth of quartz and feldspar frequently contains

Jan 1, 1949

By Walter Rose

Theoretical expressions are presented to describe wetting and non-wetting phase relative premeability relations. These expressions have then been compared with existing published data, the conformance noted being sufficiently good to satisfy the requirements of some engineering use. As a consequence, it may be supposed that relative permeability characteristics of porous media now can be inferred from basic core analysis data, in a manner more convenient (although less direct) than presently available methods of experimental evaluation. INTRODUCTION This paper presents a new approach to the problem of relative permeability evaluation. A classification of published discussions of relative permeability concepts which have appeared in the petroleum literature will show that previously emphasis has been placed on methods of experimental measurement, on the interpretation of the data so obtained with respect to the variable properties of the system, and on theoretical and practical considerations which relate relative permeability to gross fluid behavior in petroleum reservoirs. Essentially, no detailed examination has appeared which treats the fundamental factors controlling the quantitative features of the relative permeability relation*, although cer- tain references can be Cited where a qualitative awareness of their existence and nature is indicated. This condition is explainable in terms of the recognized complexity of the problem, and in order to provide some basis for theoretical development, the general emphasis has been placed in the past on experimental procedures of evaluation, the validity of which, in principle, could be confirmed by the analysis of well and reservoir performance. However, because of the experimental difficulties which have been encountered (notably, difficulties due to the so-called "end effects"), and because of the general unreliability of field performance tests required to study the applicability of the data, relative permeability phenomena continue to be incompletely understood and described.? In this paper is examined the possibility of predicting relative permeabilities entirely from fundamental considerations. In addition, attention is called to certain important factors, previously unemphasized in the published literature, which now can serve as a basis for the eventual experimental confirmation of this and similar theoretical approaches, as well as the experimental solution of the problem in general. Therefore, the analysis presented herein has the dual purpose both of orienting future experimental activity and also of providing an immediate solution for the relative permeability porblem, sufficiently adequate for some engineering use. It will be seen that the conclusions reached are supported by theoretical and intuitive considerations, and they are not contradicted insofar as gross features are concerned by existing concepts and interpretations of published experimental data, except as specifically noted. Darcy's law, expressed simply as: k dp q = k/u dp/dx .......(1) where q is linear rate of flow (assumed horizontal), k is the † The poor comparison usually obtained between laboratory and field gas-oil ratios (c.f.. Fig. 4 of paper by L. E. Elkins) is illustrative of conditions which dimcourage unqualified acceptance of the results of previous studies except as presently useful approximations. In this connection, Evinger and Muskat have discussed in detail the discrepancy observed between field well productivity values and values obtained from the analysis of laboratory flow data.

Jan 1, 1949

By Paul T. Allsman

The Salt River range vanadium deposits are situated 3 to 6 miles east and southeast of Afton, Lincoln County, Wyo. The vanadium occurs in a continuous bedded shale zone of the Phosphoria formation extending from the vicinity of Afton into southeastern Idaho. The Bureau of Mines explored several of these vanadiferous-shale deposits between December 1942 and December 1943 and conducted metallurgical tests on the ores. The areas investigated were west Swift Creek, the Dry Creek, and the Cottonwood Creek. The vanadiferous-shale beds have been folded sharply into a series of tightly compressed, eroded anticlines and synclines, which form the Salt River range. The vanadium occurs in a series of narrow shale or mudstone beds contained within the phosphatic-shale member of the Phosphoria formation. Exploration by the Bureau of Mines consisted of surface trenching and underground work over 18 miles of outcrop of vanadiferous shale with an average assay value of 0.866 percent V2O5.

Jan 1, 1949

By G. R. Rubly, H. J. Steele

The San Manuel property is in town&ips 8S and 9S, range 16E, Gila and salt River Base and Meridan, State of Arizona. This area is in the Old Hat mining district, southern pinal county, and is about 31/25 miles southwest of the town of Mammoth on the San Pedro River And one mile south of the Mammoth mine at Tiger, Arizona, The property consists of over 150 contiguous lode claims. The old Hat district was prospected prior to the civil war, but there was little or no production until 1881.1 The chief producers have been the Mammoth and Mohawk mines, now consolidated and operating as the st. Anthony Mining and Development Co., Ltd. Production to 1936 was $5,200,000, of which 83 pet was gold.2 Since 1940 the production has been chiefly lead and zinc, and some molybdenum and vanadium. There are a few small properties in the vicinity that have produced very minor tonnages of copper ore. In the San Manuel group there are claims which have been held continuously from 1906 to the present time, and at least two churn-drill holes were put down on or near the outcrop in 1917. No logs for these holes are available, but it is assumed that the grade of copper encountered was not sufficient to encourage further exploration. A small amount of ore has been shipped from open cuts on the San Manuel outcrop area, but there is no record of the tonnage Or grade. It is estimated that not more than 50 tons were mined. These cuts, plus a few shallow shafts and some short adits indicate limited and unenthusiastic prospecting at San Manuel. In 1942, through the efforts of James M. Douglas, R. B. Giffin, Victor Erickson, and Henry W. Nichols, owners of the Sari Manuel group, the Reconstruction Finance Corporation and War Production Board authorized the United States Geological Survey to investigate the property, and by their recommendation, the United States Bureau of Mines was authorized to put down a limited number of churn-drill holes. The Bureau of Mines carried On drilling from November 1943 to February 1945 Seventeen holes were drilled, varying from 305 to 1990 ft in depth. The property was brought to the attention of Magma Copper Co. in June 1944, and an option agreement was made with the Owners. Subsequently, a group of claims lying north of the original group and held by the Apex Lead Vanadium Mining Corp, and a group to the east held by the Quarelli family, were optioned. A drilling program was laid out to conform to the Bureau of Mines pattern, and drilling started in December 1944 Sari Manue1 Copper Corp. was incorporated September 1945, and has carried on the exploration program to the present time. Geology General The mineralized outcrop, chief copper mineral of which is chrysocolla, is a tri-

Jan 1, 1949

By G. L. Oldright

In an earlier series of 15 Reports of Investigations on Smelting in the Lead Blast Furnace, experimental data were given on the operations of a custom smelter, a smelter treating rich lead products, and a smelter treating highly zinciferous charges. Five "reports" were written on each of the three types of operation, which were later compared in a summary written for the Institute. Developments in each of these types of operation in lead smelting since the last of the above reports was written have continued and have followed modifications necessitated by changes in the nature of the products received for smelting. The sintering-blast furnace-smelting plants have improved their sintering operation .and have made "2-pass" sintering a more standard operation; the richer lead feeds are diluted when marginal precious metal ores are not available to prevent fusion of the sinter cakes and to permit air to contact the sulfides. Means have been devised to make it easier to remove metallic lead from the wind boxes, but no attempts have been observed to use the D & L somewhat as an ore hearth to make more metallic lead. Except in those cases where zinc-rich lead blast-furnace slags were to be retreated in a "slag-fuming furnace," the sintering and the blast-furnace operations were so carried out that a relatively "clean," lead-poor, final slag was discarded.

Jan 1, 1949

By M. B. B. Research Council of Alberta Crockford

Introduction Kootenay strata of Lower Cretaceous age contain much of the highest rank coal produced in Alberta. These strata outcrop in the foothills and mountains of southwestern Alberta and southeastern British Columbia, and the economic value of the coal seams contained in them was evident to the earliest explorers, who refer co them in their journals. Lacer, investigation of the .coal measures was undertaken by prospectors and by a succession of geologists, most of whom were in the employ of the Federal government, but some acted for private interests. Surveys by these men proved chat foothills and mountain regions hold immense quantities of high-grade coal within easy reach of transportation facilities, and their conclusions have accelerated the development of the coal-mining industry m Alberta. Among geologists who have contributed much to our knowledge of the region are J. M. Dawson, G. M. Dawson, R. C. McConnell, D. B. Dowling, J. D. Mackenzie, B. Rose, J. R. Marshall, B. Rose, J. R. Marshall, B. R. McKay, J. A. Allan, and J. L. Carr. The present paper is to a great extent a compilation of the work of the above men and of several others who have investigated the area lying between Bow river and Crowsnest pass. Space does not permit a list of all the sources of information so chat only chose of prime importance are given in the text. Data for the map and ?cross-sections of Figure 1 were taken from the following published maps of the Geological Survey of Canada: Cascade Coal Basin, Pub. 933; Canmore, Maps 322 and 323; Upper Elk River and Upper Highwood Rivers, Pub. l980; Blairmore, Pub. 1584; Southfork Coal Area Map l03A; and of the Research Council of Alberta: Highwood-Elbow Area, Map 20; and Ribbon Creek Area, Map 21. In some cases, the cross-sections have been simplified or otherwise altered, and for these revisions the writer cakes full responsibility. The stratigraphic sections of Figure 2 have been taken from published reports of the above mentioned organizations. The area covered in this paper is shown in Figure l. It is wholly within Alberta, and reaches from township 5 to township 27 and from range 1 co range 11, west of the fifth meridian. Its location is about fifty miles west of both Calgary and Lethbridge. Topography of the area ranges from foothill on the east to mountainous on the west. In this paper' the foothill region is considered to be chat which lies immediately east of the most easterly mountain ranges, such as Livingstone and Highwood. There are two principal coal mining districts in the area, one served by the main line of the Canadian ?Pacific railway and centring about Canmore, the other by a branch line of che same railway and centring about Bellevue, Blairmore, and Coleman.

Jan 1, 1949

By Albert L. Toenges

The development of Alaska depends on the existence of an adequate fuel supply in the Territory. The need to investigate coal deposits was recognized as early as 1911, when the first investigations were conducted in Alaska by engineers of the Bureau of Mines. Conditions existing in the Bering River and Matanuska coal fields, as found by Dr. Robert A. Holmes, former Director of the Bureau of Mines, are described by the Honorable W. L. Fisher, former Secretary of the Interior./ Following Dr. Holmes' investigation, a party of Bureau of Mines engi¬neers headed by R. Y. Williams visited the Bering River field in 1912 in cooperation with the Navy Department. A detailed examination was made of the Bering River field, and 855 tons of coal were mined from three prospects on Trout Creek. This bulk sample was delivered to the Navy for steaming and other tests. A description of the work of the field party and results of tests of the coal by the Navy Department and the Bureau of Mines has been published.

Jan 1, 1949

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By Oliver C. Ralston, Foster Fraas

Electrostatic methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to bene-ficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollas-tonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. The Separator The separator used in these tests is of the nonhomogeneous field type shown in Fig Ia. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll."

Jan 1, 1949