Search Documents

By Jay R. Burns

TWO magnesium sand-casting alloys are commonly favored in the United States. These are referred to as H and C alloys (Dow Chemical Co.) or 4Mz65 and AM260 alloys (American Magnesium Corporation). Both are of an aluminum-zinc-manganese type. H alloy contains 6 per cent aluminum and 3 per cent zinc and is characterized by relatively good toughness. C alloy contains 9 per cent aluminum and 2 per cent zinc and is employed where high yield strength and pressure tightness are required. Examination of magnesium castings poured in Europe and England,'J however, demonstrates that H and C alloys are replaced by .%8 and AZ~I, respectively. That is, A8 reprcsents a magnesiurn alloy having superior toughness while A291 is suitable for high yield strength and pressure-tight applications. The basic difference between the .Ameri-can and European alloys is that the foreign alloys employ a somewhat higher aluminum content and less zinc than is found in H and C alloys. The mechanical properties of the alloys, when divided into high and low-aluminum groups, are quite similar, as determined from separately cast foundry-control type test bars ,In this paper the decrease of mechanical properties caused by any given amount of microporosity is measured for H, C, A8, and AZ~I alloys. The relative susceptibility of each of the four alloys to microporosity is also determined. Typical mechanical properties and nominal chemical analyses are reported in Table I. The apparent similarities between the two alloys in each group have led to considerable discussion as to the relative merits of each of the compositions.2 Popular points for comparison between the alloys have been the relative susceptibility of each of the four alloys to microporosity6 and the effect of this microporosity on their mechanical properties. It is primarily intended, in this paper, to show the

Jan 1, 1946

By R. S. Busk, R. F. Marande

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By E. L. Anderson, J. R. Long, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By J. R. Long, R. S. Dean, F. S. Wartman, E. T. Hayes

The production of titanium in I5-lb. lots and with a purity sufficient to be consolidated into ductile metal, as described in a previous paper,' has provided adequate material for a study of the physical properties of titanium and a more thorough examination of its working qualities. Data on the physical properties reported in that paper were obtained on metal fabricated by a fixed procedure, standardized for the purpose of control of the reduction, and are representative only of material fabricated under those conditions. There are many possible variables in the working schedule, which will have significant effects on the properties of the finished material; and since the previous working methods were not necessarily the best, an investigation of the fabrication of titanium by other methods was undertaken. In this work the consolidation of the powder by pressing and sintering was conducted essentially as outlined in the report cited' and all efforts were centered on fabrication methods for those powders and the proper- ties produced by them. Hardness, density, microstructure, and tensile properties were determined at various stages in the working and annealing; and resistivity measurements were made on a few bars and drawn wire. Consolidation of the PowdeR The screen analysis of the available titanium powder is given in Table I. No attempt was made to alter the size distribution from that noted because this powder, although coarse by normal powder-metallurgy standards, produced acceptable compacts suitable for the present work. Because of their large specific surface, finer powders are more contaminated by oxygen and produce harder compacts, which are difficult to work. The powder as produced is soft, compresses in a normal fashion, and exhibits very little tendency to adhere to the die surfaces. Unlike aluminum and magnesium powders, it can be readily pressed without the use of die lubricants. When compacted at 50 tons per

Jan 1, 1946

By F. R. Hensel

PuRe silver and silver-lead alloys have been studied as to their suitability for bearing~.' A review of the properties of thallium and the silver-thallium constitutional diagram was made by the author to analyze the possibilities of silver-thallium compositions for antifriction materia1s. t The silver-rich end of the diagram as reported in the literatureg-" was found to be sketchy and it was necessary to carry out corisiderable experimental work to arrive at definite conclusions. Some of the results of this work are reported in this paper. Test Materials In the beginning of the work, only fused alloys were investigated. Later, research Table i.—Composition of Fused Silver-thallium Alloys Tested for Antifriction Properties Percentage Alloy No. of Thallium 1533...................... 0.48 1534.................... 1.06 a31 HT................... 2.04 231....................... 2.10 232 HT................... 3.83 Balance 232....................... 4.07 Silver 233 HT................... 5.86 a33....................... 6.38 a34....................... 9.84 a34 HT................... 10.07 was carried out on electroplating methods and diffusion processes. In preparing the fused alloyst care was taken to exhaust the toxic fumes caused by the thaillium content. The compositions of the series of fused alloys are listed in Table I. The silver-thallium alloys were melted in clay-graphite crucibles and cast into preheated steel molds of 3/4-in, diameter. In the cast condition, they showed a cored structure, as indicated by the micrographs of Figs. I to 3. The etching reagent used was a mixture of 2 grams K2Cr207, 8 C.C. H2S04, and IOO C.C. H20. The cored structure is unsatisfactory for the type of corrosion resistance required for bearing applications, and homogenizing experiments were carried out at various temperatures, the results of which are shown in Figs. 4 through 8. The alloys with a lower thallium concentration, which were heated for 2 hr. at 525°C show an almost completely homogenized solid solution type of structure. With higher thallium concentration, the homogenizing temperature was dropped to 475OC. to eliminate the formation of a liquid phase. It is evident that heating for 2 hr. at this temperature did not iesiilt iii complete elimination of the cored structure. As would be expected, cold-working of the cast structure is an expedient in establishing equilibrium conditions. The fine homogeneous grain structure shown in Fig. 7 corresponds to the cold-worked area under the Rockwell ball penetration when the hardness was taken before heat-treatment. A detailed structural study was made on a cast silver-thallium alloy containing 3.67 per cent thallium. Three micrographs (Figs. 9, 10 and 11) show the transition

Jan 1, 1946

By E. A. Nesbitt

The important permanent-magnet alloys 15 years ago contained carbon and depended upon it for their permanent-magnet properties. In recent years great advances have been made in a number of new alloys substantially free of carbon. These include Remalloy,' an alloy of iron, cobalt, and molybdenum, the various iron-nickel-aluminum alloys of the Mishima2 type, and the more recent Alnico V3 in which the best properties are developed by heat-treating in a magnetic field. The Mishima and the Alnico types of alloys are very brittle and after casting must be ground to size. This article describes a permanent-magnet material4 that can be machined as cast, and when handled with some care can be rolled to thin sheet and drawn to fine wire. Optimum magnetic properties are developed by a simple heat-treatment, and at this time the ductility of the alloy disappears. If the cast alloy is heat-treated without cold-working the mag netic energy product is about 1.0 X 106. This material is called Vicalloy I (pronounced vicalloy, V for vanadium, I for iron, and C for cobalt). When the alloy is first hot-worked and then considerably reduced in area by cold-swaging, drawing or grooved rolling, it is found that after heat-treatment the magnetic energy product measured in the direction of previous extension can be increased to 2.0 to 3.5 X 106. These higher values have been obtained only after reductions in area of 75 to 95 per cent, and since the material hardens considerably during working, the reduction ordinarily can be accomplished only in fine wires, although larger sizes can be reduced by the use of powerful machinery. When the material has been cold-worked in such a manner as to improve its energy product substantially, it is called Vicalloy 11. Commercial use of Vicalloy has been made in the recording of speech. Tape 0.002 by 0.050 in. has been found superior in quality to all others tried, and is now used in the Western Electric Mirrorphone 5 In a variety of forms Vicalloy I or I1 is useful in many laboratory instruments, and in experiments in which the sizes and shapes required cannot be obtained with the other more brittle permanent-magnet materials. In 1936, during a study of other age-hardening magnetic systems, it occurred to the author that some of the iron-cobalt-vanadium alloys might be suitable for permanent magnets. The proportions of iron, cobalt, and vanadium were varied and a range of alloys of particular interest was found, as shown by the indicated area in Fig. I. The limits of this range of composition are 30 to 52 per cent iron, 36 to 62 per cent cobalt, and 4 to 16 per cent vanadium. The compositions indicated by points outside this area were also tested. Preparation and Properties OF Vicalloy I The alloys were usually cast in graphite molds into bars 3/4 in. in diameter and

Jan 1, 1946

By G. P. Gladis, R. H. Atkinson

Palladium has been used for jewelry for many years, particularly in conjunction with gold. This use increased in amount during the war, as palladium and gold were only moderately used for war purposes while demands for platinum and some of the other members of the platinum group were so great that their use in jewelry was prohibited. Palladium hardened with a small percentage of ruthenium has the necessary technical properties and appearance for good jewelry, and it is sufficiently rare to be desirable for luxury items—at least I00 times as rare as gold. Although both visual and spectro-photometric examination demonstrated that the color of Palladium was almost the same as that of platinum, a few jewelers found the surface of palladium, even after some polishing, rather dark in areas that had been repeatedly heated during the soldering necessary to assemble certain types of handmade ornaments. This phenomenon is not to be confused with the thin, bluish oxide film that can be produced by heating in air over the range 400' to 800°C., as that film is easily reduced by dipping in warm 5 per cent formic acid or in warm methanol. It was suspected that the difficulty arose from heating in atmospheres that were alternately oxidizing and reducing, as Wise and Vines1 had found that this opened the grain boundaries of palladium and palladium-silver alloys in the same manner as in pure silver, as reported by Martin and Parker.2 This damage is caused by the reaction between oxygen in solid solution in the metal, acquired when heated under oxidizing conditions, and hydrogen diffusing in from subsequent heating under reducing conditions; the steam cannot diffuse out and therefore builds up sufficient pressure to disrupt the metal near the surface. Copper and various other metals can be damaged similarly, but platinum is nearly immune; therefore the problem was new to the platinum jeweler. Sulphur in the fuel gas also can cause trouble but did not appear to be dominant in the present instance. Metallographic examination of both pure palladium and ruthenium-palladium showed that the usual torch using oxygen and city gas as normally operated did in fact cause the surface and subsurface damage that had been observed, and also disclosed that a reducing flame caused more damage than an oxidizing flame and was very damaging even in the absence of any intentional swing in atmosphere from oxidizing to reducing (Fig. 7); besides the surface damage, there was serious loss of ductility. A full explanation of the mechanism of attack is not evident at the moment, but may be allied to the attack that occurs on heating catalytically active metals in nonequilibrium atmospheres.

Jan 1, 1946

By Bruce W. Gonser, Robert I. Jaffee

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By W. R. Clark, W. W. Cotter

Jan 1, 1946

By T. L. Fritzlen

Extrusion of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact1 that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relation- ship between the temperature of the material being extruded and the pressure required to extrude. According to Schi-shokin,= this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. Characteristics of the Equipment The capacity of the press determines * the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1946

Jan 1, 1946

Jan 1, 1946

Jan 1, 1946

Jan 1, 1946

Jan 1, 1946

Jan 1, 1946

By T. I. Harkins, J. Brian Eby

This paper outlines the geophysical investigation of the area covering the D arrow salt dome, Louisiana. Surveys with the refraction seismograph and torsion balance failed to disclose the dome, but reflection dip shooting was successful and was confirmed by later drilling. Introduction The D arrow salt dome and oil field lies in western Ascension Parish, Louisiana, on the outside of a sharp bend and on the east bank of the Mississippi River. The dome occurs about 30 miles south of Baton Rouge and 80 miles northwest of New Orleans. Its geology, shape and structure have been ably described in detail by Carroll E. Cook' and, except for the general features, will not be repeated here. The purpose of this paper is to record some of the interesting and pertinent geophysical data contributing to the discovery of the dome and eventually the oil field. The salt dome is circular in outliie and comes to within about 4625 it. of the surface. At this depth the diameter of the salt plug is approximately 4800 it. The dome has only a thin cap rock of less than 75 ft. Some oil has been found and is being produced in Miocene sands above the cap rock, but most of the field's production comes from a narrow ring of wells around the east and south flanks of the dome. Producing horizons on the flank are found at 5670 to 5840 ft. in the Miocene and 6890 to 6985 ft., 7028 to 7060 ft. and 8260 to 8270 ft. in the Oligocene. The deepest well that has been drilled is the Humble Oil and Refining Company's Community B-5, on the south flank of the structure, which reached a depth of 10,013 feet. The size and shape of the field and the area of production are indicated on Fig. I. The lie showing the area of production encloses all wells now producing and all abandoned producers, both on the top and flank of the dome. This line of production is shown on all subsequent geophysical maps as a direct means of comparing the early geophysics to later drilling development. Darrow dome occurs on the low, flat flood plain of the Mississippi River; it is protected from flood overflow by high artificial levees. The rich loamy soil supports a high degree of cultivation, principally sugar cane. Drainage is secured by many small canals and the water table of the area is at or near the surface. These particular conditions of topography, drainage and top soil greatly influenced the early geophysical picture, and the influence was always unfavorable.

Jan 1, 1946

By Donald C. Barton

OF the four papers that comprise this Technical Publication, three are case histories of individual geophysical prospects, subsequently tested by drilling. The bibliography of Dr. Barton's published scientific paperst includes investigations in physiography and surface geological mapping, as well as his geophysical papers, and from this list it is to be observed that he early recognized the place of different types of geophysical prospecting methods in the search for geological structures of economic importance. Moreover, his viewpoint was not merely that the structures should be found, but that the geophysical data should be examined quantitatively to determine the geometry of the structures. In other words, that although these data are insufficient to deduce a unique form for the structure that caused the effects measured in the data, the engineering computations should be carried out to give as much of a definite configuration to the structure as the data permitted, in order that the testing of the structures could be conducted in the most economical manner and with the idea that the experience so gained could be later incorporated in the study of structures subsequently found. Dr. Barton continually emphasized the quantitative use of geophysical observations, whereas at the time that he began his specialization in geophysics it was considered sufficient to use observations only qualitatively. He, more than any one else, was responsible for the first volume on geophysical prospecting issued by the Institute in 1929, and his three articles in that volume stressed the quantitative use of geophysical prospecting. The fourth article in this present Technical Publication is a further contribution to this branch of geophysical interpretation, and is a supplement to the paper in the 1929 volume, "Calculations in the Interpretation of Observations with the Eötvös Torsion Balance." From the successful demonstration by Dr. Barton of the usefulness of quan-

Jan 1, 1946

By Henry J. Joesting

During the past year and a half, the Territorial Department of Mines in Alaska has conducted a modest experimental program for the purpose of determining the extent to which magnetic and resistivity methods can be used in interior Alaska in connection with prospecting, mining and geological studies. Since little information is available concerning previous work,l,2 and since conditions differ considerably from those in most other regions, it was considered advisable to make a general study of the possibilities and limitations of the two methods, rather than a detailed study of any single problem. Problems One of the most serious handicaps to prospecting and geological study in interior Alaska, especially in the mature regions, is a cover of unconsolidated deposits ranging in thickness from a few feet to several hundred feet. These deposits, some of which are permanently frozen, consist of silt with varying proportions of vegetation and windblown material in the valleys and of residual deposits on the hills.3'4 The problems treated here are caused by the existence of this overburden: I. Location of buried placers. 2. Determination of depth and areal distribution of permanently frozen and of thawed unconsolidated deposits. 3. Location of water-bearing beds under unconsolidated deposits. Instruments and Methods Magnetic and direct-current resistivity methods were used because they are relatively simple, rapid and inexpensive and because generally they are well suited to the study of the problems indicated. The instruments used were a vertical Schmidt-type magnetometer and a direct-current resistivity instrument similar to those used by the Geophysical Branch of the U. S. Geological Survey. For placer surveys with the magnetometer, a sensitivity of about 25 gammas per scale division was found suitable. For resistivity studies of frozen and thawed overburden and of underground water, the Lee partitioning method6 was found to be most generally suitable. In the Lee method a central potential electrode is placed midway between the two potential electrodes of the Wenner four-electrode configuration.7 Nonpolarizable electrodes were made from unglazed porcelain pots about 10 cm. high and 5 cm. in diameter. In order to retard evaporation of the electrolyte the sides of the pots were glazed, inside and out, with clear Duco lacquer. For resistivity work in cold weather, a nonfreezing electrolyte consisting of equal parts of ethylene glycol and a saturated water solution of copper sulphate proved satisfactory. Stainless steel rods of 3/4-in. diameter made excellent current electrodes because their bright finish enabled good ground contacts to be made.

Jan 1, 1946

By H. Cecil Spicer

The results described in this article are based On field work conducted during the periods April-May, I939, and May-July, 1940. The United States Potash Co. is mining potash on Government land under a permit from the Department Of the Interior and the geophysical investigation was completed under a cooperative arrangemerit made between that company and the Conservation Branch Of the Geological Survey. The writer, a member Of the SeCtion of Chemistry and Physics of the Geologic Branch, was assigned to this investigation. Four definite objectives were in mind for the geophysical work in the studies over the salt deposits. The first was to determine the measure Of success that could be attained in this type of work with the resistivity methods that were to be employed. These methods had been introduced into the work of the Conservation Branch by Benjamin E. Jones for the investigation of dam sites, and have been used under his direction by the author for such work. If the method proved to be be an effort was to be made to contour the top of the salt beds and also the other formation boundaries known to be present in this area. Salt-water aquifers were to be studied in an effort to determine their boundaries, and an attempt was to be made to delineate the potash-bearing beds. Earlier Studies Others have made, and reported, restivity studies over saliferous deposits in different areas. Friedell and Messrs. Schlumberger2 reported geophysical work performed in the discovery of the salt domes of Alsace; Carrette and Kelly? described the geology of the same area. Leonardon and Kelly' published a resistivity curve obtained over the Hettenschlag dome, and a further discussion of this same area was given by the Messrs. Schlumberger6 in a communication. Messrs. Alty6 described studies on salt deposits in which the single-probe method was used. sinerez7 mentions that electrical methods were tried over salt deposits in Spain. Geoffrey and Charrin8 show a resistivity curve obtained over marl, gypsiferous marl and salt which is similar to that obtained over the New Mexico salt deposits. Kelly9 reported resistivity work performed with the ground Comparaor of Zuschlag over the salt deposits near Syracuse, N. Y., where the Salina formation is at a depth of 700 to 800 ft. Some structural studies on the potash basin of Alsace are described by Poldini.10 Another single-probe resistivity study, made over salt deposits in New Mexico, is briefly described by Heiland,11 through the courtesy of Harry Aurand, of the Midwest Refining co, Geological Features OF Area Covered The area discussed in this paper is in Eddy County, southeastern New Mexico, a

Jan 1, 1946