Search Documents

Jan 1, 1938

By A. C. Richardson

Troughs or launders are probably the oldest machines used for ore concentration, and their development was suggested no doubt by the natural segregation and stratification of materials that take place in the bed of a stream. Trough washers for coal cleaning were first used in France and Germany about one hundred years ago and have been used in some form or other ever since. The early launders were intermittent or batch machines, and only comparatively recent developments have made them continuous. The chief disadvantage of early launder systems as applied to coal has been that when a satisfactorily clean coal was produced the loss of good coal in the refuse was excessive. Other disadvantages have been the large quantities of water and the great lengths of troughs necessary to treat moderate tonnages of feed. One of the most widely used types of trough washers is the Rheolaveur, which has been developed in the last 25 years. Fig. 1 shows a more or less standard arrangement for fine coal. In this there are four trouglis placed one below the other and sloped a few degrees from the horizontal. Rheo-boxes or draws are provided at intervals in the bottom of the trough for the removal of material deposited from the stream. These draws are spaced substantial distances apart. Some of the rheo-boxes are provided with upward currents of water to modify the horizontal current stratification. In operation it is the function of the first two troughs to remove all refuse material and permit only clean coal to be discharged over the end. In order to accomplish this, large quantities of coal are drawn through the rheo-boxes. The third and fourth troughs are used to recover the coal discharged through the boxes of the first two troughs as a middling product and to discharge a clean refuse. The middlings are returned to the first launder and are usually about equal to 40 per cent of the raw coal being fed to the launder. In considering launder processes, one would reason that the conditions of extreme crowding under which stratification takes place in a flowing stream should effect complete separation in a single pass down a launder.

Jan 1, 1938

By M. J. Williams, C. P. Proctor, J. T. Crawford

The purpose of this paper is to present some data and comparisons regarding three types of Rheolaveur plants washing bituminous coal from the Pittsburgh seam. It deals only with the sections that handle coarse coal. The Rheolaveur system consists of launders or troughs in which coal and its associated impurities are conveyed by water. The impurities. being heavier than the coal, settle toward the bottoms of the launders and are drawn off through specially designed openings called Rheo boxes. Fundamentally, each plant consists of straight-sided, flat-bottomed launders of varying width and length, each launder equipped with one or more Rheo boxes for the removal of high-grauity fractions of the feed that are undesirable in the cleaned coal. Each launder has at least two longitudinal sections, the first with a slope of from 11/2 to 4 in. per foot of length, called the classification section. The single-box launder has a classification section followed by a washing section ahead of the box. A two-box launder is a single-box launder followed by a washing section and a second box. The slope of the washing section between the first and second boxes is determined to some extent by tonnage. At the end of the classification section, which may. vary from 8 to 15 ft. in length, the slope abruptly flattens out to a slope of from 92' to 1 in. per foot of length. This flatter section of the launder, called the washing section, may vary from a few feet, in a single-box launder, to 15 ft., in a two-box launder. Raw coal entering the head end of what we choose to call the "primary" launder or launders is pushed down the classification section by a stream of water entering the head end of the launder with the coal. As it strikes the washing section, of lower pitch, the velocity of flow is retarded and the heavier particles of slate, pyrite, bone, etc., take their places on the bottom and are drawn off as they pass over the Rheo boxes. The clean coal, of lighter gravity, remains on the top of the stream of

Jan 1, 1938

By William Reynolds

This paper deals with the results of a study of the application and development of mining machines for cutting out and removing dirt bands in bituminous coal beds. Face Preparation When one or more dirt bands1 occur in a seam of coal, the problem of elimination of impurities becomes manifest. The degree of completeness to which these impurities arc removed at the face has an important bearing upon labor costs, haulage costs and outside cleaning costs, and often the ash content of the product is markedly affected. Yet, because the present-day miller is paid for the number of tons he loads he often lacks interest in the quality of the coal. To insure a clean product, a system of penalties for dirty coal is enforced, but control of extraneous impurity content in the loaded coal is often inadequate and ineffectual when coal and banded impurity are shot as one. It seems only logical that to reduce the amount of impurities by proper face preparation before the men are permitted to load the coal is the most efficient method of preparation. Many mines with one or more bands of impurities in their seams are able to mine a desirable product with a comparatively small amount of surface preparation. In fact, three companies in West Virginia have recently changed their methods of fact* preparation, with most gratifying results. The first company (in the Kanawha field) after changing its cutting practice with the hope of relieving a sales problem, was rewarded by an approximate 3 per cent drop in ash in the product. Another company, operating in the same field, reduced its ash approximately 4 per cent by a change in cutting practice. The third company (in the Pocahontas field) found the wet washer inadequate in producing a marketable coal, and installed new cutting machines. Three cuts are now being made in each working place, and the results arc so satisfactory that the cleaning plant has been abandoned.

Jan 1, 1938

By Frederick M. Becket

DoctoR Albert Sauveur, distinguished scientist and Honorary Member of this Institute, predicted in the first Howe Memorial Lecture that the privilege of delivering' this annual address would be considered a highly significant honor. The intervening years have well borne out Sauveur's prophecy. I wish to assure the American Institute of Mining and Metallurgical Engineers that I also deeply appreciate this honor, recognizing at the same time the present and even more the future responsibilities with which it is accompanicd. Several of the previous lecturers had the good fortune to attend the classes of Professor Howc and to work in his laboratories. I was similarly favored, although in my instance and to my great regret the period was all too short. However, Howe's book, published in 1903, "Iron, Steel and Other Alloys," afforded me abundant opportunity to continue these studies. How well I remember the inspiration I derived from this famous book by Howe, the metallurgical master, pioneer, and educator! Remembering that Professor Howe contributed numerous papers to The Metallographist, a magazine supported from a technical point of view by the world's pioneers in metallography, I was curious a few days ago to learn the nature of Howe's early contributions to this magazine. The first paper by Howe in the first year of The Metallographist (1898) dealt with the allotropic theory; the second also treated of allotropy, and I quote the first sentence of that paper: The allotropic theory of the hardening of steel may, like so many other important theories, have to be accepted or rejected not on direct proof or disproof, but on the accumulation of circumstantial evidence for or against it. Howe's ability to stimulate others by his deep understanding and clarity of expression was truly remarkable; but just as striking was his intuitive judgment concerning the implications of metallurgical data in the arts and scienees. It therefore seems fitting that this lecture comprise a broad treatment of the subject chosen, rather than a closely documented thesis on any one phase of the problem; that in it attention be focused

Jan 1, 1938

By W. E. Curran

For years the geographical isolation of the Southern iron-ore district from the great producing centers in the North and East enabled it to meet its conditions and solve its own problems without regard to the practices and policies of other districts, but during the past few years distances have been shortened, practices and wages are being standardized, and these changing conditions have brought new problems to the South. Development of Pig Iron in the South The development of the pig-iron business in the South was very slow during its early years, gained speed rapidly in the latter part of the nineteenth century, reached its peak in 1918 and was on the decline before the depression that began in the latter part of 1929. The first blast furnace in Alabama was built at Cedar Creek in 1818, the year before the state was admitted to the union. In 1830, Daniel Hillman was sent from Tuscaloosa to found an iron works in Roupes Valley, where rich pockets of brown ore were numerous. He built a forge on the site of what later became Tannehill furnace and called it the Roupes Valley Iron Works. There pots, pans, plows, and horseshoes were made of metal from his Catalon forge; shaped by a large hammer operated by water power. Daniel Hillman died in 1832 and the ironworks lay idle until 1836, when Col. Ninion Tannehill bought the property, rebuilt the forge and, using slave labor from his plantation, operated and enlarged the works. By 1845 he had built two crude furnaces and did a flourishing business in ovens, skillets and kettles, which found a good market all over the South. In 1855, the plant was sold by Colonel Tannehill to Moses Stroup, an experienced ironmaster from Pennsylvania. He tore down the old furnaces and built a new plant, the ruins of which stand today (Fig. l). This furnace plant operated continuously until it was destroyed by Northern troops in 1865. It was never rebuilt, so that the shell in the picture is the same furnace that made many tons of guns and shells for the Confederacy during the war period.

Jan 1, 1938

Jan 1, 1938

Jan 1, 1938

Jan 1, 1938

Jan 1, 1938

Jan 1, 1938

Jan 1, 1938

By Harry A. Roe

The power drag scrapers and the slackline cableway excavator have been called "long-range excavators." Broadly, their field of usefulness is restricted to work in which their long range of action permits them to operate economically, and which other, possibly more conventional, excavating units cannot do. Both of these machines dig or lift material and transport it to a remote dumping point. They combine these two functions in a single machine, nearly always in a single straight-line motion. The purpose of this paper is to examine the important features that distinguish the machines in this group from each other, as well as from other groups. The Machines The "power drag scraper" is a long-range excavating machine that employs a bottomless drag scraper operated back and forth between digging and dumping points by two haulage cables. The typical arrangement is that of Fig. 1. This is the "slusher" of the underground mine, as well as the "dragline scraper" of the sand and gravel industry, and other open-pit mining operations.

Jan 1, 1938

By Mark Sheppard

DuRing the winter of 1937, the writer visited a West Virginia stone quarry at which the overburden is stripped hydraulically. The quarry is in a bed of limestone, about 200 ft. thick, which outcrops on a hillside above a small river; the quarry face is 175 ft. high. The top of the stone is cut in all directions by erosion channels, which are filled with a tough, red clay. Some of the larger channels are 30 ft. deep and 8 ft. wide. The thickness of the clay overburden ranges from a few inches to 10 ft., the average being estimated as less than 3 feet. The topography of the district is rugged, and the hillside above the quarry face is not suited to the use of the usual mechanical methods of moving dirt. Until hydraulicking was started 10 years ago, the overburden was dug by hand labor, dumped to the quarry floor and transported to the dump in quarry cars. Cleaning deep channels was a slow and expensive process. When hydraulicking was started, the top of the quarry face was over 200 ft. above the level of the river. The pipe line was carried in a semicircle around the top of the quarry about 200 ft. from the face and about 50 ft. above it. As there is no adequate supply of water above the quarry, the water must be pumped from the river. As quarrying progressed the pipe line was moved until the discharge points are now over 300 ft. above the river. Water is pumped from the river by a four-stage centrifugal pump having a 5-in. intake and a 4-in. discharge. It is direct-connected to a 200-hp., 2300-volt, 1760-r.p.m. induction motor. At 1760 r.p.m. the rated capacity of the pump is 750 gal. per minute under a head of 600 ft. The pump is installed in a house of frame construction on the river bank, about 10 ft. above normal water level, which also houses the pump for the mill-water supply. Above the pumps are hoisting bays into which the motors are raised whenever the river reaches flood stage. An 8-in. suction line, equipped with a strainer and a foot valve, takes the water from a concrete sump at the edge of the river. The pipe line from the pump consists of 1750 ft. of 8-in. spiral steel flanged pipe and

Jan 1, 1938

By Nelson Severinghaus

The Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also presents several theories on the action of explosives in this type of blasting. The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break down the rock in large blocks.

Jan 1, 1938

By W. F. Netezband, E. H. Crabtree

The productive area of asphalt-bearing sandstone in Missouri is near the Missouri-Kansas state line near Nevada, the county seat of Vernon County about 100 miles south of Kansas City. While production thus far has been confined to Vernon and Barton counties, there are known deposits in adjacent counties. The area is served by four railroads: the Missouri Pacific, the Kansas City Southern, the Missouri-Kansas & Texas, and the St. Louis & San Francisco. The plant of the Reliance Rock Asphalt Corporation is in Vernon County, about 5 miles west of Nevada, at Ellis, a flag station on the Missouri, Kansas & Texas Railroad. A siding has been built to the plant SO that the finished product can be loaded directly into railroad cars. The property consists of a lease of 240 acres in one block. All portions of the property not required for quarrying or processing the asphalt-bearing sandstone are used for farming by the fee owner. The entire tract is very flat so that there are no transportation difficulties from quarry to plant. Geology The commercial asphalt-bearing sandstones are all of Pennsylvanian age, the major portion of the production coming from the Cherokee formation, the basal member of the Des Moines group. The Cherokee formation includes all beds between the base of the overlying Fort Scott limestone and the Mississippian limestones below. It underlies most of the area, but in the west and northwest townships of Vernon County, and elsewhere in local outliers, the Henrietta limestone, forming mounds, escarpments and high ridges, covers the Cherokee, and is in turn covered by the Pleasanton shale. In the eastern portion of the counties, the Mississippian limestones are exposed. The thickness of the Cherokee varies according to the amount that has been removed by surface erosion. Where fully present under the Henrietta; it is approximately 375 ft. thick, but over most of the county it ranges from 100 to 200 ft. thick.

Jan 1, 1938

By Oliver Bowles

When a new type of equipment revolutionizes methods of quarrying one kind of stone, producers of other kinds focus their attention on its potentialities in their particular fields. The purpose of this paper is to discuss the accomplishments of the wire saw in slate, to show its more limited attainments in other kinds of stone, and to point out the possibilities of much wider application. A wire saw consists of a 3/16-in. or ji-in. three-strand wire cable that runs as a belt and cuts the rock by abrasion. (Fig. 1. The teeth of the saw are sand grains carried in the grooves between the strands. Accomplishments in Slate† Initial experiments with wire saws by the U. S. Bureau of Mines in the Colonial Slate Quarry, Wind Gap, Pa., in 1926, attained success so immediate and pronounced that within two years in virtually every quarry in the neighborhood of Wind Gap, Pen Argyl and Bangor, the most productive slate area in the United States, wire saws were substituted for channeling machines. An 80-ft. cut in slate is shown in Fig. 2. The technique of operation has been described in several reports (references at the end of the paper). The present purpose is to summarize the accomplishments in a large, typical slate quarry after nine. years of experience. Parsons Bros. Slate Co., at Pen Argyl, Pa., substituted two wire saws for six channeling machines in 1927. The following comparisons are made between the present method with wire saws and the former channel-ing-machine method. Rate of Sawing.—The average rate of cutting with a wire saw in the early days of its operation, as determined by the Bureau of Mines', wits 14 to 17 sq. ft. per hour. Parsons Bros. Slate Co. estimates the present rate of cutting at about 25 sq. ft. an hour, whereas the channeling-rnarhirle

Jan 1, 1938

By C. E. Abbott

The Birmingham district, Alabama, is distinctive in the proximity to one another of its deposits of iron ore, coal and flux. These three basic requisites for the making of iron and steel are found within a radius of 10 miles. Both dolomite and limestone are produced, the former for blast-furnace flux and the latter for basic open-hearth operations. The Tennessee Coal, Iron and Railroad Co., a subsidiary of the United States Steel Corporation, operates a limestone mine at Muscoda, near Bessemer, 12 miles southwest of Birmingham, served by its own railroad transportation system. The mine has a capacity of 130 tons per hour. Average analyses of a recent month's production arc as follows: Fe²zO³ SiO² Al²O³ CaCO³ MgCO³ Lump, percent............................. 0.51 0.22 98.63 0.14 Crushed and washed, per cent,................ 0.70 0.26 98.36 0.18 Lump stone, 2 1/2 to 755 in., is used in open-hearth operations at Fairfield Steel Works. Fine crushed and washed stone, 1% to 0.063 in., is calcined at the lime-burning plant and used for lime charges at the Ensley open hearths. Geology The district's deposits of hematite ore occur in the Clinton formation, and the limestone beds mined are stratigraphically 330 ft. above the ore beds worked. A cross section on the center line of the mine is shown in Fig. 1. This limestone formation, 130 ft. thick, is in the Warsaw horizon of the Lower Mississippian. It lies above 100 ft. of Fort Payne chert, which is immediately above the Clinton formation, and is composcd of layers of chert and cherty limestone, approximately 50 per cent of the material being pure chert. The chert is extremely hard, and the cost of driving raises through it is very high. Both iron ore and limestone deposits lie on the southwest limb of the Jones Valley anticline, the formations dipping from 15' to 32' to the southeast. The iron-ore seam outcrops along the crest of Red Mountain, a ridge with northeast-southwest trend rising 200 to 300 ft. above Jones and Shades valleys at the

Jan 1, 1938

By Ralph W. Smith

Development of the lime industry in Ste. Genevieve County began in a crude way in 1840. According to information furnished by the Missouri Bureau of Geology, in the early days small vertical kilns built of stone were used, and wood was the fuel. Modern development began in 1904 when one company introduced steel shells lined with firebrick. Within a few years two more companies erected similar plants, and in 1925 a fourth company began operations. Thus there arc today four lime companies at Ste. Genevieve, all operating at high capacity and with a gradually increasing production. Geology The limestone of Ste. Genevieve County, which has the chemical composition and purity required for lime burning, is the upper 80 or 90 ft, of Spergen formation. The Missouri Bureau of Geology, in its geological map of Ste. Genevieve County, gives the Spergen formation a total thickness of 160 ft., but only the upper portion is pure enough for lime burning, with an average raw-stone analysis of 98.7 per cent CaCo3; 0.35 SiO2; 0.3 R2O3; 0.35 MgCO3; 0.3 SO3. The Spergen, one member of the Meramac group, Iowa series, of the Mississippian system, underlies an area approximately 12 miles long north and south, by 5 miles wide east and west (Fig. 1) in Ste. Genevieve County. The entire eastern two-thirds of Ste. Genevieve County is sedimentary, the formations dipping gently toward the east on an average grade of about 4 per cent, or 2 1/2°. Thus the outcrops of the various sedimentaries run approximately north and south. A line running west from Ste. Genevievc crosses the outcrops of the sedimentaries, ranging from the top of the Mississippian to the Ozarkian geological system in a space of 12 miles. Thus with the gentle dip of 2 1/2° the 160-ft. thickness of the Spergen formation stretches out in its outcrop so that it is approximately one mile wide. The early quarry and lime developments at Ste. Genevieve mere in this easily obtained surface rock of the Spergen outcrop.

Jan 1, 1938

By George W. Bain

Methods of mining building stone of any sort are planned to produce as few fractures as possible, and present a strong contrast to methods of mining metallic ores, which must be crushed eventually and have fractures produced in as great profusion as possible. Shocks transmitted to a stone invariably make it more porous and more permeable and reduce its effective life, therefore methods of mining building stone involve as This building illustrates the fine detail of workmanship, unprotected sharp corners and thin edges, and tall narrow columns characteristic of marble structures. These features require exceedingly coherent stone, and preservation of these features for decades or centuries demands many special quarrying precautions to keep absorption to 0.14 per cent or less, a detail not essential to stone for coarser architectural types. few shocks as possible. This is singularly true for marble because marble structures are intended to have long life, greater delicacy of line, more gracefulness and fineness of sculpture than those made from any other structural material (Fig. 1). So that delicate lines may remain in almost perfect preservation for decades, or even centuries, it is important

Jan 1, 1938