Search Documents

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By J. E. Gosline

In any theory of a hydrodynamic nature dealing with the vertical flow of gas-liquid mixtures in pipes, the two factors that present the greatest difficulty are the relative motion between the phases and the energy loss resulting from turbulence work. The former has generally been referred to in the literature as "slippage" and the latter as "friction." A third factor of importance is the nature of admixture between liquid and gas for both the relative motion between the phases as well as the turbulence work are functions of the type of mixture. Although much work of a general nature has been performed on the vertical flow problem, there have been very few attempts made to study experimentally the factors involved in the phenomenon individually. Of these, perhaps the most notable is the work of Moore and Wilde1 on slippage. Some writers on the subject have assumed that over a wide range of operating conditions the controlling type of mixture is one in which gas bubbles of uniform size are distributed throughout the liquid, and that the data obtained from experiments on the motion of single bubbles through various liquids may be used in evaluating the slippage. Ver-sluys2 has further assumed another controlling type of mixture in which the liquid occurs as a dispersed phase within the gas and applies data on the fall of drops of water in air to calculating the relative velocity. It was for the purpose of studying the applicability of data on single bubble motion to the slippage factor and to further observe the nature of mixtures that a research program was conducted at the University of California during 1932 and 1933. These experiments formed a basis for

Jan 1, 1936

By W. K. Lewis, Lombard Squires, W. I. Thompson

The authors presented an article2† last year on colloidal properties of clay suspensions in which they attempted to sustain the position that the behavior of clay suspensions is due primarily to the mechanical interference of the platy particles, the nature and extent of the interference being profoundly influenced by the character of the surfaces of the particles, which in turn is determined primarily by the nature and amount of adsorbed foreign materials held on the surface of the particles by forces which are predominantly chemical in type. The following discussion is a continuation of that article to extend these same interpretative points of view to the behavior of clay gels. Insight into the mechanism of gelation is certainly of outstanding importance in the handling of drilling muds. In the former article it was suggested that the thin, flat plates that constitute the ultimate clay particles may build up aggregates by the overlapping of the ultimate plates face to face much longer and perhaps also much wider than the ultimate plates themselves, but not appreciably thicker. Exhaustive microscopic examinations of characteristic clays show no tendency for the larger particles, clearly visible under the microscope, to orient themselves in this way. It is true that the gelation of the clays is due primarily to the smallest particles, unresolvable other than by the ultramicroscope, so that the possibility of the deve1opment by them of an overlapping structure is not excluded. Furthermore, as one approaches the limit of resolving power of the microscope, the difficulty of observing accurately the shapes and relative positions of particles incresses excessively. However, in the absence of any observable tendency toward overlapping orientation of the large, visible particles, one hesitates to ascribe such a tendency to the smaller particles beyond the range of visibility. Should it develop that one must exclude the assumption of overlapping orientation, the explanations offered in the previous article are changed in only one respect; namely, one would now have to assume that the ultimate particles themselves have length, and probably also width, very large in comparison with their thickness.

Jan 1, 1936

By D. T. Jones

In view of the importance of the application of scientific principles to the production of oil from the reservoir, the Production Staff of the Anglo-Iranian Oil Co. (late Anglo-Persian Oil Co.) has been engaged for some years on an intensive program of research on the physical properties of crude oil. Problems involving the retention of crude oil in capillaries and fine fissures demanded for their solution a knowledge of the surface tension and specific gravity of the crude under reservoir conditions, and it is the purpose of this paper to describe briefly the methods adopted for the determination of these properties, and to present the more important results. A detailed article was published in volume 1 of the World Congress Proceedings (1933). Surface-tension observations on crude oil regassed at high pressures with natural gases have been made in the past by Beecher and Park-hurstl and Swartz2, but up to the time of the investigations in Iran no one seems to have carried out experiments with gas-saturated crude direct from the reservoir and kept at its original pressure. Results obtained in this manner are obviously of greater practical value for solving problems connected with the reservoir. Method of Measurement No apparatus for the measurements, under the pressure conditions involved, was available, and a suitable instrument had to be designed and constructed in the Fields workshops. Careful consideration of the matter led to the adoption of a method for measuring the surface tension which did not involve a knowledge of the specific gravity of the oils under the working conditions: the main reason for this being that up to that time no accurate determination of the specific gravity had been made under these conditions. The method adopted involves the measurement of the actual tension in an oil film, and is effected by means of

Jan 1, 1936

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit, the selection of the proper material and size of sucker rods, and the design of the pumping unit, requires that the sucker-rod loads be known with a reasonable degree of accuracy. In production practice, it is also desirable to know the effects of operating speeds and strokes on a plunger motion, as well as on the rod loads. For a particular well, data on rod loads can be obtained by measuring the load in sucker rods with a dynamometer. This method is not satisfactory because it does not permit the various factors to be investigated independently. It is also impossible to measure the plunger motion simultancously with rod motion under operating conditions. The mathematical solution is impractical because of the simplifications that have to be made to get a solution and the tremendous amount of numerical work that is necessary after such a simplified solution has been attained. This paper shows how analogies and models can be applied to the solution of these problems. The loads set up in a sucker-rod string during the ordinary pumping cycle are made up of the weight of the rods, force required to accelerate the rods, weight of the oil and force required to accelerate the oil on the upstroke, rod friction, stuffing-box friction, plunger friction, friction of the oil in the tubing and rods, arid friction loss through the valves. The problem of determining the sucker-rod load is further complicated by the fact that the long oil column and the sucker-rod column act as springs, which affect the transmission of the polished-rod motion. A further complication is the fact that the motion cannot be transmitted at a speed greater than that of the velocity of sound in the material, and this means that there will be a time lag in the transmission in the motion, as well as a modification of its magnitude and a phase displacement.

Jan 1, 1936

By F. B. Plummer, R. B. Newcome

The practice of introducing acid into oil wells to increase production of oil and gas has been in use since 1894, when it was first used in the Pennsylvania oil fields30.‡ It is only since 1928 that it has been used to any extent in the Mid-Continent18. The process has proved successful in increasing production, at least temporarily, in depleted oil fields where the producing formation is highly calcareous and where water drive is not too pronounced. In the Zwolle field in Louisiana, where the producing horizon is a chalk, increases of 100 per cent have been recorded25. In north-central Texas, where the oil is produced from the Marble Falls limestone, equally pronounced increases have resulted3. The production also in some fields yielding oil from quartz sand cemented with calcitc has been benefited. The evidence of actual increase in total recovery of oil, however, has been questioned by some engineers18. It has been pointed out that the results of the treatment of a well in a now district, where the process has never been tried out, can never be predicted with certainty, since other factors besides percentage of calcareous content of the oil sand play a large part in determining the success of the method. Numerous articles have been published on acid treatment and on the effects of acid on limestone1-35, yet very little has been written concerning experimental work on the actual effect of acid on capillary pores and larger oil-coated voids of oil sands. This is due partly to difficulties in duplicating field conditions in a laboratory and partly to the fact that the process has been carried out largely by contracting companies that have been unwilling to publish details of their results for fear of loss of business to competitors. The authors, using equipment developed to measure the radial permeability of oil-sand cores2', have developed a method of investigating the results of acid treatment which has enabled them to test numerous cores and to study in some detail the action of acid on the different types of rocks, particularly fine-grained rocks.

Jan 1, 1936

By Erwin H. Leeman, Raymond R. Rice, Gerald L. Hassler

In the past few years a great deal of preeise information has been obtained about the relation of natural gas to oil production1. The improvement of our understanding has been of great value, both in prolonging the life of wells and in providing a much needed technical background for the legal problem of proration. But there are two principal aspects of the problem of production. It is necessary to consider not only the energy available, in the form of compressed and dissolved gas and in the pressure of driving water, but also the tenacity with which the sandstone holds the oil. The amount of oil that each sand condition will produce under given conditions of gas content should be determined. Hitherto the effect of the sand has been judged by a study of the flow of each well coupled with a procedure for extrapolating the production curve; hut, as is well known to evaluation engineers, such production curves are subject to changes that are not well understood, and often are affected by outside disturbances. On the whole, the concept of "potential production" is vague principally because the influence of the sand in production is not known beyond the simple ideas of porosity and permeability. The permeability is a quantity that has only inference value where mixtures of gas and oil or of gas, oil and water are present. Excellent studies of the production of oil from reservoirs packed with unconsolidatcd sand are available2, but these studies treat largely of small-scale analogzes to a producing field, and the conclusions to be derived from them arc necessarily of a qualitative character because it is not known in what way these miniature oil fields resemble large ones.

Jan 1, 1936

By Kenneth B. Barnes, George H. Fancher

With the advent of water-flooding into active commercial usage in half a dozen areas in the Mid-Continent, the process passes the experimental stage and joins other methods and processes now in use which have been found suitable in one oil field or another in securing a more profitable production than has existed heretofore. The use of the air-gas lift, acidization, pressure maintenance and repressuring have presented their problems in economics and engineering during their introduction and extended application. When a new field is discovered or attention is turned to an old producing area in which these methods have not been considered, it is to be expected that these problems again arise. While some information is available as to the results obtained by water-flooding in a few localities in the Mid-Continent, the extrapolation of the sand data on which the results are based, for even generalized use in other areas and fields in the region, is hazardous. It is precarious to assume that the same physical condition will obtain in a sand over more than small, special areas. This paper is concerned with a brief presentation of such data as are available to the authors on existing operations, a survey of the region and extent to which application of the method seems most likely to be made, an estimation of the crude reserve existing for such operations, suggestions as to the importance of core analysis in guarding against uncontrolled floods and its usefulness in predicting ultimate recoveries, and comment on some of the economic phases involved. These subjects, as concerned with water-flooding in the East (notably Bradford, Pennsylvania), have been discussed in detail in the literature and are generally well known. Especially is this true of discussions of the mechanical equipment and various lease layouts and development patterns for water-flooding.

Jan 1, 1936

By H. T. Kennedy

The fact that intrusion of water into oil wells can be prevented by treating the sand adjacent to the well seems to have been only recently recognized. Swan1 mentions the process of solidifying naphthalene in strata. R. Van A. Mills2 recommends the use of materials such as sodium silicate and sodium carbonate, which react with oil-field water to form solid plugging agents. When a well is drilled in a new field the oil sands are found essentially devoid of water (Fig. 1). Unless a completely impermeable break exists over wide areas in the field, no water is found above the lower limit of the oil zone and no oil is found below the upper limit of the water zone. After considerable oil has been taken from the well, however, it is almost universal experience that water intrusion occurs. This intrusion may be of two kinds. The water may follow a path parallel to the bedding planes of the producing formation through loose streaks in the pay sand, as shown in Fig. 2, or the water level of the field may rise and enter the well by coning (Fig. 3). Water entering from the side is called "edge water," and that coming in from the bottom is called "bottom water.'' Effectiveness of any method for shutting off water depends not only on the effective treatment of the sand adjacent to the well but on

Jan 1, 1936

By C. P. Parsons

During the past year considerable interest has been shown in cementing operations for shutting off bottom water, whipstocking, etc. A number of plug-back methods have been used, with various adaptations for special conditions, but those described in this paper are representative of the methods now in use. Conditioning the Well Various preliminary operations for improving the results from plug-back operations have been evolved. In one method, a nitroglycerin shot is discharged at the upper portion of the formation to be plugged off, the purpose being to make a wide place in the hole in order to give the cement a more secure anchor against thrust pressure of the water against the bottom of the cement plug after the well is again put on production. Another is intended to attain a similar result by under-reaming a wide place in the hole by means of a rotary wall scraper. In one well in which this device was used there was a water sand at the bottom of the well immediately below the cap rock above which the oil sand occurred. Before the plugging back operation, the water sand was underreamed in an attempt to get a square shoulder on the underside of the cap rock, in order to prevent the water from breaking in over the top of the cement plug after the well should be put on production, and also to get a more secure anchor for the cement plug against the thrust pressure of the water against it. As an aid in calculating the amount of cement required to fill a given amount of hole to be plugged back, a device has been developed for measuring and recording the irregularities and cavities in open holes, called an "open-hole recording caliper." If consists of a steel shell, 5 in. in diameter, which encloses a recording mechanism that receives impressions from four movable arms that make sliding contact with the wall of the hole. The arms operate a ratchet, which raises and lowers a recording stylus against a chart. Each arm registers its own radius. The device is run into a well on a steel measuring line. While the device is being lowered, the arms are folded inside the shell; they are

Jan 1, 1936

By Joseph E. Pouge

For the purposes of this analysis it is assumed that the petroleum industry has undergone a basic economic change whereby the degree of competition present in its operation is reduced by the collective control of production brought about by statme-directed proration. Formerly freely competitive in all its parts, the industry is now fully competitive only in its marketing, its manufacturing and transportation, its search for new oil supplies, its drilling operations (with some qualifications), and its capital movements. The practical problem before the industry in its new status is the maintenance of equilibrium, with planned control of crude-oil production (proration) substituted for competition and price as the regulatory mechanism at one point in the supply-demand system. It is further assumed that proration has become so firmly established in the legal and operating framework of the business that it may be looked upon as an institution. The purpose of this paper is to call attention to the effect of unregulated drilling upon the orderly functioning of proration. Economic Structure of Petroleum Industry The economic structure of the petroleum industry, under the current form of proration, may be visualized, in simplified form, as shown in Fig. 1. This diagram is designed to indicate the existing mechanism whereby supply and demand are equated. Demand is created largely by conditions external to the oil business, whereas supply is conditioned by a series of stages incidental to the discovery, development and production of a resource. The time elements involved in changes in demand and supply are of an entirely different order, the demand factor being much more flexible and "quicker" than the supply factors. It should be observed, also, that the position of price, formerly between "demand" and "supply," has been moved to a sidewise location where it still affects demand but influences current supply only through its bearing upon proration, drilling and search. Proration has been substituted for price as a throttle at the well head, but at this point only. The mechanism now works in this fashion: a declining price stimulates demand and the

Jan 1, 1936

By Northcutt Ely

A year ago the petroleum code was in effect, and Congress had before it bills with powerful backing designed to extend and put on a permanent basis the Federal authority impliedly recognized in the petroleum code. Those men in the industry who were convinced of the unconstitutionality of Federal regulation, who believed in conservation, and who were seeking accomplishment of a conservation compact among the oil-producing states, were at that time encountering difficulties in bringing about such an agreement. Since then there has been a shift in the center of gravity. Today, by virtue of the Supreme Court's Schechter case decision, the petroleum code is not in existence, the industry is not operating under an oil administrator, and the Federal-control bills are not on Congress' calendar. In view of what the Supreme Court has said in the Schechter case and the Hoosac Mills case about the local character of mining and manufacturing, the problem today is not whether the Federal Government or the State Governments ought to regulate oil production, but how effective we can make the devices that are available to us under the constitution for the conservation of the nation's oil resources. The interstate oil conservation compact ratified during the past year by Texas, Oklahoma, Kansas, New Mexico, Colorado and Illinois, approved by Congress, but not yet in effect in California, is the mechanism now at work. Interstate Oil Conservation Compact What is this interstate compact? The basic theory is simple and logical. It has four elements to it. The first point is that in order to effect the maximum recovery of our oil arid gas reserves it is necessary for some governmental authority to regulate the way in which those resources are taken out of the ground, so that the reservoir energy is efficiently used, and used equitably by the various owners of the pool. Second, that the state, as distinguished from the national government, possesses the police power necessary to protect the public interest and to protect the correlative rights of the common owners of the oil pool. Third, that the state governments ought to cooperate with each other through an interstate advisory commission so that orderly production in one state is

Jan 1, 1936

By V. R. Garfias, R. V. Whetzel

It is estimated that world consumption of petroleum, its products and related fuels during 1935 will reach an all-time peak of 1,592,000,000 bbl. —about 5.4 per cent higher than in 1934. Demand increased within the United States approximately 6.1 per cent during 1935 and in foreign countries about 4.1 per cent. The figures in Table 1 indicate that during the past five years world's production of crude petroleum and related fuels exceeded demand every year and that the aggregate difference is approximately 239,000,000 bbl. The supply in the United States exceeded consumption by some 134,000,000 bbl. over the same five-year period, while outside the United States the excess over demand is shown to be 105,000,000 bbl. Table 2 combines the excess production in the United States with its favorable balance of exports over imports, showing that the United States has reduced its storage over the five years by about 132,720,000 bbl., and indicates that, including its excess of imports from the United States, the rest of the world may have an unfavorable balance of some 371,000,000 bbl. over the five-year period. Such difference in foreign countries is largely due to increase in stocks, and partly at least remains in our imperfect knowledge of consumption statistics as an unfavorable balance. Table 3

Jan 1, 1936

By V. R. Garfias, R. V. Whetzel

It has been repeatedly questioned whether estimates of oil reserves are of any practical value, as the greater number of such calculations previously made have subsequently been proved to be grossly inaccurate. But even admitting partial justification for such statements, it must be evident that some idea, however approximate, of the available reserves of essential minerals—petroleum included—is of vital importance in mapping their development and the future trend of the related industries, particularly if it is kept constantly in mind that these estimates are not only never intended as a final word but must continually be subject to revision in accordance with the changes in their component factors. The value of these estimates, therefore, hinges on the clear understanding of what is meant by reserves and that the figures can only apply within the limited time when the controlling factors remain unchanged. It should be understood, further, that while estimates of possible and probable oil deposits are as a rule but idle conjectures, appraisals of proven oil reserves can undoubtedly be made with an ever-increasing degree of accuracy. And it is with this in mind that in the present study the endeavor has been to estimate only the world's proven oil reserves and to leave out of consideration the questionable volume of the probable and possible oil reserves. Such a survey presupposes further a clear distinction between the known amount of oil underground in proven fields at any one time, and the proven reserves: the portion that can be economically brought to the surface and made available for utilization. Only a fraction of the petroleum stored underground in proven fields— usually associated with natural gas—is or can be economically brought to the surface, and not all of the oik brought to the surface is economically utilized; also, although practically all the natural gas can be economically recovered and utilized, in actual practice a large part of the total volume that reaches the mouth of the well is wantonly blown into the air and wasted. It is thus estimated that in the United States only some 25 per cent of the petroleum stored underground in proven fields is actually brought to the surface; and in actual practice close to 25 per cent of the total gas produced is now absolutely wasted. And the dissipation of this

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Arthur Green

A GROUP of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point sear Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections.

Jan 1, 1936

By The Staff

The San Anconio mine, owned by San Antonio Gold Mines, Limited, is located on the north shore of Rice lake, thirty miles east of lake Winnipeg, and about one hundred miles northeast of the city of Winnipeg. The three claims which formed the original San Antonio group were staked in 1911. Subsequent additions to the Company's property have in-creased their holdings co thirteen claims. Preliminary development of the property took place between 1925 and 1930. The major ore discovery during this period was the 16 vein. The mine was closed in September, 1930, but re-opened in April, 1932, since which rime it has been in continuous operation. In 1933, a development of special importance was that of the 26 vein. The mill capacity, originally designed for 150 tons, was increased to-wards the end of 1933 to 170 tons. With highly satisfactory mine development, mill enlargement to approximately 300 tons was made possible. The Company has financed the additions and improvements from mine production. Iris of interest to note that San Antonio is the first gold mine in Manitoba to pay a dividend. The first dividend was paid to the shareholders in March, 1934, and the fourth was recently declared. Electric power is transmitted to the property from the Great Falls plant of the Manitoba Power Company over a 66,000-volt transmission line approximately 62 miles long. The old camps, which had been in use since work on the property was started, in 1927, were demolished in the spring of 1934, and new camps were built on the Ross dam. Lumber for these buildings was out at the Company's saw-mill on Gold creek, eight miles from the mine. Two bunk-houses with a capacity of 72 men each were constructed, also a dining room co accommodate 144 men, a store, staff house, hospital, burcher shop, and warehouse. The camp buildings are all steam-heated from an electric boiler. They are all insulated on walls, roofs, and floors with a heavy building board, and are covered on the outside walls with asbestos siding, and on the roofs with corrugated iron. A community of about 800 persons has grown up around the mine, at Bissert. Attention has been given co their social interests, and the management of the mine has assisted its employees co build a community hall, which is used for dances, picture shows, and other entertainments and amusements. A two-room school, with an attendance of 50 pupils, is supported by Company employees. In addition, picnics, boxing contests, and hockey games are encouraged among the employees.

Jan 1, 1936

Jan 1, 1936

Aamot, Olav Crone, Research Engr., Norsk Elektrokemisk Kongensgt, 18, Oslo, Norway ?29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. '32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. '31 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service Club, 16 St. James' Sq., London, S. W. 1, England. '28

Jan 1, 1936

By O`Donnell. P. J.

THE modern coal cutter is a highly developed, and to a certain extent a somewhat complicated, machine. The requisite power to cope with conditions as found must be generated by the motor with due regard to limitations in the matter of dimensions and weight. This imposes the necessity of relatively high speeds of rotation. Any factor external to the machine proper which tends to reduce the load on the motor and gearing is most important. Experience has proved that close attention to the question of cutter-chain details undoubtedly results, in practically every coal-cutting operation, in increased efficiency and reduction of power and maintenance costs. The chain is the unit of the coal cutter which most greatly affects the economical operation of the machine, and only by due consideration of conditions and by the proper selection of the right chain can best results be expected; also, intelligent care of the chain while in operation is essential if it is to give its best service. The chain is the part of the machine that carries the pick boxes or blocks, which are connected to each other by a pair of chain links. The power to drive the chain is trans-mitted by a sprocket. The chain runs in guides supported by a rigid member called a 'jib'. Figure 1 shows the various parts mentioned. The first requirement of a chain is that it cut the coal as fast as possible. The second is that it do so economically. Economy of cutting can conveniently be divided as follows: (1) Economy in power used. (2) Economy in pick life. (3) Economy ' in chain life. ( 4) Economy in jib life. (5) Economy in labour for maintenance.

Jan 1, 1936