Search Documents

By Renato Pereira da Silva Junior

Soluções poliméricas são uma alternativa para meio de resfriamento com coeficientes de extração de calor intermediários ao da água e do óleo. Pode resultar em uma severidade menor em relação à tempera em água e uma menor emissão de poluentes, maior penetração da tempera e maior segurança em relação à tempera em óleo. O objetivo deste trabalho é analisar a influência da solução aquosa com 0,03% de Álcool Polivinílico (PVA) como meio de resfriamento para o aço carbono SAE 1045, comparando-se os resultados de microestrutura e dureza do aço SAE 1045 como recebido e após tratamento térmico de têmpera nos meios de resfriamento: água, óleo e salmoura.

Aug 17, 2017

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Roberto Balarini Junior

Tribological behavior of Si3N4 balls sliding against Al2O3 discs in water was investigated by studying the influence of parameters such as initial surface roughness and circular axial run-out of the discs. The objective was to relate these parameters with the occurrence of the phenomenon known as ultra-low friction coefficient (ULFC), which is characterized by µ < 0.01, including the correlation with running-in duration. As a general trend, greater initial surface roughness and circular axial run-out resulted in greater running-in duration. In addition, it was verified that a mixed lubrication regime (hydrodynamic and boundary) is required to guarantee the occurrence of ULFC by comparing the calculated minimum film thickness with the composite roughness of the worn surfaces. Also, ICQ-OES analysis of the water after the tests indicated that a silicon concentration greater than 1.3 mg/l should be fundamental for the occurrence of µ < 0.01.

Jul 31, 2018

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By Júlia Guimarães Sanches

O curso de Engenharia de Minas sofreu uma expansão, juntamente com todo o ensino superior no país, por volta de 2005. O objetivo do presente estudo é avaliar as características dos cursos do país e realizar uma comparação com cursos de outros países com grande produção mineral. Foi feito um levantamento inicial a partir de informações disponíveis nos sites do MEC, INEP e das universidades. Como complemento, realizou-se um questionário com os coordenadores dos cursos de Engenharia de Minas do Brasil. Foram compilados ainda dados relativos à estrutura curricular e carga horária dos cursos de Engenharia de Minas dos EUA, Canadá, Austrália, Chile e África do Sul. Em relação à comparação das grades curriculares com os cursos de outros países, observou-se que no Brasil o curso possui uma maior cara horária de Tratamento de Minérios em detrimento da lavra. Nos demais países estudados, o foco das disciplinas é a lavra, já que nestes países a área de Tratamento de Minérios é assunto de outras Engenharias.

Oct 30, 2017

By Maísa Villela Freire

Refratários MgO-C encontram-se entre os mais adequados para o uso na linha de escória de panelas para aço líquido. Seu comportamento, nesta aplicação, depende de fatores termodinâmicos e cinéticos. Métodos de cálculo termodinâmico para avaliar o potencial de degradação de refratários MgO-C por escórias e pela atmosfera são revistos brevemente. Tais métodos envolvem, em geral, premissas importantes sobre a quantidade de materiais envolvidos. Para avaliar um método mais simples, foram escolhidos dois tijolos MgO-C e duas escórias típicas do processo da CSN. Estes tijolos e escórias foram caraterizados, neste trabalho. O método apresentado consiste na realização de cálculos de equilíbrio em que a principal variável é a fração de escória em uma mistura hipotética com o refratário. Para a composição do refratário foram empregadas (a) composição média e (b) composição da matriz do tijolo. Os resultados indicam que é possível realizar previsões iniciais quanto à reatividade do refratário e determinada escória de forma simples. Os cálculos, evidentemente, não substituem testes cinéticos e testes em escala industrial, em vista da complexidade dos sistemas em questão.

Aug 17, 2017

By Rodrigo Monzon Figueredo

Neste trabalho foi estudada a corrosão dos aços API 5L B e X52MS em soluções ácidas descritas nas normas NACE TM0284 e TM0177. A susceptibilidade ao trincamento induzido pelo hidrogênio (HIC) foi determinada em cada meio, os produtos de corrosão foram caracterizados por microscopia eletrônica de varredura e espectrometria de energia dispersiva de raios-X e, posteriormente identificados por difratometria de raios-X. Conclui-se que o pH afeta diretamente a solubilidade dos produtos de corrosão e a permeação de hidrogênio. Na solução 177-A, ambos os aços sofreram corrosão generalizada, enquanto que na solução 177-B foi evidenciada a presença de um filme fino descontinuo. Somente o API 5L B não passou no teste de HIC. Na solução 284-B de maior pH, os aços apresentaram filmes espessos e o trincamento pelo hidrogênio não foi observado.

Oct 30, 2017

By Paula Maria Gomes Cunha Leão

Um modelo matemático tridimensional, via software Fluent 14.0, de modo a descrever o fluxo, em regime transiente e isotérmico dos fluidos escória e nitrogênio, foi utilizado para avaliar o comportamento de slag splashing em um convertedor a oxigênio com o propósito de reparar as regiões desgastadas do revestimento de trabalho deste reator. Para um dado padrão de sopro foi investigou-se o efeito de parâmetros tais como temperatura, densidade, viscosidade e tensão interfacial. Os resultados são comparados com dados de projeção disponíveis na literatura.

Aug 16, 2017

By Juan Garcia de Blas, Allan Ribeiro de Souza

uso do método dos elementos finitos (MEF) para uma determinação mais realística da resistência estrutural de aços estruturais sob a ação do incêndio vem crescendo à medida que um número maior de países vem adotando os códigos baseados em desempenho no lugar dos tradicionais códigos prescritivos. O algoritmo MEF interpreta o comportamento termomecânico do aço através do emprego de modelos constitutivos. Os modelos constitutivos convencionais usados na engenharia de incêndio são de natureza empírica e abordam de forma dissociada os fenômenos do encruamento plástico e da fluência. Este trabalho apresenta em linhas gerais um modelo constitutivo unificado baseado fisicamente na cinética de deformação plástica resultante do deslizamento de discordâncias, encruamento e recuperação dinâmica inspirado nas contribuições de Kocks, Mecking e Estrin. O modelo proposto tem a sua estrutura matemática modificada para condições de temperatura variável, isto é, para cenários de incêndios.

Oct 1, 2019

By Jorge Madias

Los hornos eléctricos de arco han sido motivo de una aplicación dinámica de nuevas tecnologías en lo que va de este siglo. La preparación de la chatarra y el uso de materiales de carga alternativos han dado lugar a la concepción de nuevos equipamientos y experiencias en todo el mundo. Surgen nuevos conceptos para el precalentamiento de la chatarra, superando las limitaciones de mantenimiento y ambientales de los conceptos iniciales y mejorando su performance energética. El aporte de energía química para la fusión supera sus límites año a año, requiriendo el desarrollo de equipamiento capaz de una acción rápida y precisa con grandes caudales de gases y sólidos inyectados. Existen nuevas herramientas para eliminar los riesgos de seguridad en la plataforma del horno, haciendo uso de sistemas de enfriamiento más seguros y duraderos, robots, automación de la operación del agujero de colado, y puertas de escoria controladas desde el púlpito.

Aug 17, 2017

By Foluke Salgado de Assis

Natural fibers are attracting the interest of engineering sectors owing to specific advantages such as lightweight and lower cost as well as for their inherent condition of being renewable, biodegradable, recyclable and environmental correct material with respect to CO2 emission. The banana fiber is nowadays recognized by its mechanical properties. It is known that with the increase of fibers volume fraction the composite significant increases its tensile strength. This was obtained with amounts up to 30% in volume of banana fiber. However no higher volume of fibers was able to be molded in a composite plate until now. Thus the present work aims to study higher volumes of fiber in terms of the influence on the tensile strength of specimens prepared under 5 tons of pressure. The fibers were previously washed and dried in an oven at 60ºC, after that poured together with the epoxy resin and catalyst mixture in the metal molds bone-shaped, and pressured to ensure specimens quality. The tensile strength increased significantly with higher amounts of banana fiber incorporated in the epoxy matrix. This better performance can be directly related to the fracture obstacle imposed by the fibers as well as the type of cracks resulting from the fiber/matrix interaction.

Aug 16, 2017

By Sebastien Flament

More and more Hot Strip Mills are facing defects on their products that lead to a rejection of complete product batches by their customers. Several of those defects are induced by excessive work roll degradation. This paper is focussed on the understanding of work roll corrosion and oxidation mechanisms in a hot strip mill. Several laboratory trials (Hot rolling simulator, cyclic oxidation) have highlighted important factors influencing corrosion of work rolls as well as helping the understandings of oxidation of a work roll in the roll bite and along the roll circumference in a stand. The attention is focussed on several elements present in water used in HSM for direct roll cooling (e.g. chloride, bactericides, sulphates, phosphates) and their effect on roll surface degradation. The second part of this paper is focused on the understanding of work roll oxidation along the roll circumference. The effects of roll composition, roll temperature, water composition and water temperature have been studied in order to understand the oxidation/corrosion mechanisms in a HSM.

Aug 16, 2017

By José Francisco Cabello Russo, Késsius Bortolan Menezes, Henrique Dias Gatti Turrer, Denílson Rodrigues de Araújo

With the start-up of the Minas-Rio system, Anglo American, in Conceição do Mato Dentro, MG, in 2014, a methodology was also implemented and certified to perform the tests to obtain the results of TML (Transportable Moisture Limit). Such a parameter provides the maximum moisture content contained in the material that could be transported without the risk of the cargo liquefaction process, which could lead to incidents such as the tipping of ships carrying iron ore concentrate in bulk on the deep water. This means that when loading a ship, the moisture content of the material to be transported should not be higher than the TML reference value, obtained in a physical test and intrinsic to the material. Should this occur the charging may be rejected. From 2014 a downward trend was observed for this reference parameter in the Minas-Rio system, with results approaching the moisture of the filtered product, bringing risks to the operation of the project. In this way, an investigation of the possible causes for understanding this downward trend was required.

Oct 3, 2019

By Lindaura de Souza Cândido d’Ávila, Robert Nogueira de Azevedo, Itavahn Alves da Silva, Mariana Carvalho Araújo

The present study aims at the reduction of the dolomitic limestone by the addition of lime added with high MgO (magnesium oxide) content in the sintering process. To verify the feasibility of the use of additive lime as an alternative source of magnesium oxide, sintering tests were carried out at pot grate with different percentages of additive lime addition and with proportional reduction of the calcite lime dosage, evaluating the effects on the sintering process. The results showed that the additive lime is a good source of MgO for consumption in the sintering process of iron ore.

Oct 1, 2019

By Lilian Silva Costa, Laila Bonzi Ramos, Marcela Lessa de Freitas, Igor Quaresma Vianna

The eighth pelletizing plant, located at the Tubarão complex Industrial Unit of Vale S/A in Vitória-Espirito Santo-ES, processes a pellet feed primarily composed of compact and friable itabirite from Itabira and Brucutu concentration plants, located in the iron quadrangle in Minas Gerais-MG. The use of hydrated ores in the composition of the fine piles, such as Brucutu's common fines amphibolite itabirite (FABR), and Fábrica Nova pellet feed (PEFN), contributed to increase the energy efficiency of comminution, increasing the production of tumbling ball mills, minimizing the impacts during a mill preventive maintenance.

Oct 1, 2019

By Denisio Miranda Custódio, Rodrigo Boyer, Josiane Lira Batista Haagensen, Raquel Teixeira Pereira, Felipe Viana Pimenta, Rossano Augusto Pilon Nunes

In the Tubarão Pelletizing Plants, anthracite is used as solid fuel, which has fixed carbon content of 72%. This paper will present the pilot scale results and industrial scale tests of an alternative fuel to anthracite, named Blast Furnace Dust. All the work was developed using samples from Arcelor Mittal Tubarão, due to it has a large source of production and is near to Vale/SA, which reduces significantly the cost for the material’s transportation. There was an impact on the variability in fixed carbon results of the slurry, mainly at the beginning of the test, reaching very high levels and put on risk the pellets physical’s quality. This variation can be explained by some operational disturbances and, mainly, by the low predictability of Blast Furnace Dust quality and lack of an adequate system for material preparation and dosage.

Oct 1, 2019

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Thiago Pinto Silva, Leandro Rocha Lemos, Luiz Fernando Andrade de Castro

This paper shows an evaluation about effect of dispersant sodium silicate along to limestone, in the form of pulp, on the cold agglomeration process for iron ore sintering. Before that, it was verified the effect of pH, solids content and amount of dispersant on the stability of the system (limestone, water and sodium silicate). It was found that the lower the solids content, the more alkaline pH and the amount of sodium silicate equal to 20 l for each 1t of limestone, was the level of dispersion of the system. The influence of the limestone pulp with dispersant depended on the granulometry of the ore mixture and the type of technological route. For the thinner type (42,8% <0.15mm), the limestone pulp with dispersant reduced the resistance of the adherent layer of the cold agglomerates, regardless of the technological route. However, for the coarser type (24,7% <0.15mm), the limestone pulp with dispersant increased the average size of the aggregates, preserving the resistance of the adherent layer when manufacturing with two intensive mixers in series.

Oct 1, 2019

By Pablo Altoé Amorim, Bruno Sellitti Borges, Otávio Lube dos Santos, Arthur Pizetta David, Matheus Diogo Penido da Silva

Automation is in everywhere nowadays, including within companies and industries, and is therefore fundamental and essential for production, quality and process control of them. There are many ways to automate a production line or a machine can be through relay logic, Programmable Logic Controllers (PLCs), and even more modern microcontrollers with native Internet of Things (IoT) support can be used. What are the advantages and disadvantages of each approach? A PCB was created using more modern microcontrollers programmed in C, C ++ and Whiting language to simulate a replacement of a PLC in an actual machine. Having a very positive result, being able to handle the machine manually via Wi fi besides being able to also perform a real-time monitoring of the machine's motors through the mobile phone, thus entering the IoT and fitting into the Industry 4.0.

Oct 1, 2019

By Dalila Chaves Sicupira

A pitting corrosion study of welded joints of lean duplex stainless steel (LDSS) UNS S32304 has been performed. LDSS S32304 thick plates were welded by different processes commonly employed in equipment and piping construction: SMAW (Shielded metal arc welding), GMAW (Gas metal arc welding) and FCAW (Flux cored arc welding). The electrochemical behavior of different weldment zones (fusion zone (FZ), base metal (BM) and heat affected zone (HAZ)) was characterized both independently using an electrochemical microcell and together through whole sample analysis. The electrochemical method applied was performed in acidified glycerin, a process fluid of the biodiesel industry. The results were correlated to the microstructural features of the materials. Based on the results, is possible to conclude that the breakdown potential (Eb) of the fusion zone (FZ) was higher than the Eb obtained for the heat affected zone (HAZ). In general, top samples show higher breakdown potential than root samples and also the samples welded using filler metal 2209 has a better anodic behavior than the filler metal 2307. According to the results, GMAW welding process with 2209 as filler metal was revealed as the optimum chosen for application of 2304 duplex stainless steels in this case.

Jan 16, 2018