Search Documents

By Chester A. Rowland

INTRODUCTION Comminution is generally a feed preparation step for subsequent processing stages; exceptions being when a final product such as aggregates, specification sand, Portland Cement, and similar products is produced. Grinding, the fine product phase of comminution, requires a large capital investment and frequently is the area of maximum usage of power and wear resistant materials. Grinding is most frequently done in rotating drums utilizing loose grinding media, lifted by the rotation of the drum, to break the ores in various combinations of impact, attrition and abrasion to produce the specified product. Grinding media can be the ore itself (autogenous grinding -- primary and secondary), natural or manufactured non-metallic media (pebble milling) or manufactured metallic media -- steel rods, steel or iron balls. This chapter will discuss general mill design and the specific design and application of the following types of tumbling grinding mills. [Overflow Rod Mills Figure 1 Peripheral Discharge Rod Mills Figures 2 and 3 Compartment Mills Rod and Ball Figure 6 Ball Figure 6a Pebble Mill Figure 6b Overflow Ball Mills Figure 8 Diaphragm (Grate Discharge) Ball Mills Figure 9] I. GENERAL MILL DESIGN A. Liners The interior surface of grinding mills exposed to grinding media and/or the material being ground are protected from wear and corrosion by rubber, metallic, a combination of rubber and metallic, or non-metallic wear resistant materials. B. Drives Economics at the time of plant design and mill purchase determine the drive to be used. The simplest drive is the low speed synchronous motor with speeds in the range of 150 to 250 RPM connected to the mill pinion-shaft by either an air clutch or flexible coupling.

Jan 1, 1982

By Richard E. McElvain

The mining and other industries have grown and changed with- respect to their requirements for slurry pumps capable of handling high percentages of abrasive materials. Greater solids concentration, higher heads and pressures, and increased flow arc not possible. Today's equipment delivers up to three times the flow-tonnage and 1.3 times the head per stage as compared with pumps of ten years ago. This results in four times the requirement in size and energy. The new centrifugal pumps are capable of handling these requirements at pressures up to 4826 kPa (700 psi), with 6895 kPa (1000 psi) or more being considered for future systems. The latest pumps, functioning at four times the operating requirement on flow-head, weight eight times more than the previous equipment. Efficiency is increased slightly, to about 75 % to 85%. A testing program on equivalent units has confirmed that the added strength and specific design of heavy-duty pumps can meet demanding engineering objectives. Operating life on difficult-to-pump materials is increased from 500 to over 5000 hours of continuous operation; the ten-fold increase in pump operating time is a major design objective.

Jan 12, 1976

By Michael D. Loy

While the coal industry in general has been slow in accepting automation, the last few years have seen a myriad of products developed by the private sector. These packages run the full gamut from sophisticated geological information systems to line entry discounted cash flow analyses. This paper is an attempt to unravel the confusion that may exist about mining software. Discussions will highlight major differences between software products (such as block vs. grid models, prefeasibility programs vs. Monte Carlo analyses), briefly discuss known vendors, list known package features and touch on hardware requirements. The paper also focuses on the costs of automation (both software and hardware), possible trade-offs, advantages to in-house systems (vs. timesharing), a recommended review/selection process (including suggested RFP format), a test case procedure, when to bring in a consultant, and staffing considerations.

Jan 1, 1983

By P. G. Mason

The upswing in the price of gold in 1979 prompted renewed interest in the Mercur gold property by Getty Oil Company, owner and operator, and Gold Standard Inc. of Salt Lake City, Utah, currently retaining a 15% net profits interest. Extensive geological exploration work resumed to delineate the ore reserves, and metallurgical test work was initiated under the direction of A.H. Ross & Associates. This led to the development of an aqueous pressure oxidation process suitable for treatment of the refractory ores. Subsequent geostatistical studies revealed that the distribution of high refractory ore was less than previously estimated, and thus a higher return on investment could be realized if a direct carbon-in-leach process were used despite a sacrifice in overall recovery. This paper reviews the geological and metallurgical studies that led to this final process selection.

Jan 1, 1984

By P. R., Bradley

THE Juneau gold belt is divided into ore-bands of poor definition. The most easterly workings on the , belt, those of the Alaska Gastineau Co., disclosed three separate bands: the Footwall or Ground-hog band, 70 ft. wide; the Perseverance band on which the recent mining was done, also 70 ft. wide; and the No. 2 band, 100 ft. wide. These bands, aggregating 240 ft., are found over a width of 2000 ft. Going toward the west into the adjoining Alaska Juneau ground, four bands have been found which have a total 'right-angle thickness of 755 ft. These bands are convergent in their westerly trend and terminate on the plane of Silver Bow fault. The four bands have better definition at the fault plane than at the eastern boundary line where they enter the property. -Along the property line, the width of the bands and intervening country is 1600 ft., and at the Silver Bow fault this width is reduced to 1300 ft. The distance from the eastern property line to Silver Bow fault is 2400 ft. The bands are slate or slate with metagabbro intrusions, together with gold-bearing quartz masses, stringers, and gash veins. The bands themselves are not all ore, but all commercial .ore is found within the bands. They have no uniform width either in horizontal or vertical section. The ore has no hard and fast boundary except where cut by faults, and profitable mining ceases on a vague and

Jan 1, 1929

By J. Laskowski, Z. Sadowski

The properties of quartz, calcite, magnezite and dolomite suspensions prepared from -30 µm size fractions of these minerals have been investigated. Selective coagulation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was possible at the pH values slightly above those for the i.e.p. of the carbonate minerals. The tests revealed that quartz suspensions were not flocculated by the anionic flocculants, whereas the same polymers were flocculants for calcite, magnezite and dolomite. Selectivity in the flocculation of the quartz-calcite, quartz-magnezite and quartz-dolomite binary suspensions was not, however, satisfactory because of the activation of quartz by ca2+ and Mg2+ ions. Dispersing reagents can be used to improve the selectivity of flocculation.

Jan 1, 1980

By F. S. Sinnatt

THIS paper is the outcome of an extended investigation carried out in association with Dr. L. Slater. The inquiry had been continued in various directions and a number of results are quoted from an investigation recently completed by S. H. Jenkins. In projecting the work some five years ago, the author had in view a general attack on the problem of the spontaneous combustion of coal from an angle that had received little attention. The basic idea was to obtain a "slow motion study" of the active combustion of coal. This included an examination of the conditions prevailing in a mass of coal at the moment when active combustion ceases. It was thought that, if the factors governing the extinction of combustion in coal could be definitely established, it might offer an explanation of the manner in which the spontaneous combustion of coal originates. The inquiry arose from a detailed study of the properties of fusain that the author began in 1918. Fusain seemed to possess characteristics quite distinct from the coal with which it was associated, for if it were collected into a heap and one portion were heated by a small flame the combustion would traverse the whole mass. This combustion was not accompanied by smoke and passed slowly through the heap of material. Later, it was found that coals, including anthracites, would behave in a similar manner provided they were in the form of powder and that the particles were smaller than a certain size. The limiting size of particles is a definite characteristic of the coals investigated. In view of the fact that fusain exists with coal in a state that enables it to undergo this particular form of combustion, it must be assumed, sometimes, to playa definite part in the spontaneous combustion of coal in the goaf (waste).

Jan 3, 1925

By Herbert Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electro-static separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static elec-tricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor-generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the elec-trostatic separating process.

Jan 1, 1938

By Herbert Banks Johnson

DURING the past 10 or 12 years very little information has been made generally available concerning the commercial possibilities of separating materials by means of static electricity; and yet during that same period important improvements have been made in various branches of the science of electricity, which, when taken together, and applied to electrostatic separation, have resulted in important improvements in that art as well. For example, much improvement has been made in high-voltage electrical equipment such as full-wave vacuum-tube rectification and improved mechanical rectification. Great strides have likewise been made in the development of insulators for high-voltage work, not only in the materials used but also in the design of the insulators themselves. Again, in another field, the development of air-conditioning equipment has improved the technique of controlling the surface condition, through drying or humidifying, of the various materials that are passed through the electrostatic separator. In many authoritative publications and textbooks, the electrostatic separation process is declared to require a balance far too sensitive for general commercial application. For example, one publication1 in the past has referred to an unfavorable effect on the process caused by varying atmospheric conditions such as humidity. Some2 have even gone so far as to state that sunlight and shadows may seriously affect the separating efficiency of the process. Such statements may have been true in the early development of the art, when the source of static electricity was derived from a friction disk machine, such as the Wimshurst. The Blake Mosher equipment and the work of Huff in applying motor- generator sets, transformers and mechanical rectification overcame much of this kind of objection to the commercial application of the electrostatic separating process. Another objection made periodically is that it is generally considered necessary to feed the particles into the electrostatic field in a stream that

Jan 1, 1938

By Arthur F. Colombo

The selective flocculation, desliming and flotation process developed by the U.S. Department of the Interior, Bureau of Mines, as part of its goal of maintaining an adequate supply of minerals to meet national economic and strategic needs is described. The application of the selective flocculation and cationic flotation process to three oxidized taconites from the western Mesabi Range in Minnesota is discussed. Data from the operation of a 408-kilogram-per-hour (900 lb/hr) pilot plant employing reclaimed water are summarized for the three types of oxidized taconites.

Jan 1, 1980

By K. Hanumantha Rao, A. Nayak, . K. S. Narasimhan, S. N. Mahapatra

Selective flocculation studies carried out with iron ore tailings generated at Kudremukh iron ore plant indicate that a concentrate containing 63% iron can be obtained from the tailings containing 34% iron with around 60% recovery. This opens up the possibility of recovering most of the iron lost in the tailings generated at 2 kt/h (2200 stph) while processing 22 Mt (24 million st) ore per year. This would mean that the productivity could increase by around 50%. In these studies, it has been established that caustic degraded tapioca starch is a most effective agent for selective flocculation. While potato starch after caustic degradation can also be used, neither the parent starch nor the amylopectin compound is as effective.

Jan 1, 1986

By I. Iwasaki

In the flotation of iron ores and nonmetallic ores desliming is the key to a successful operation; the technology of flotation of well-deslimed ores has become fairly well established. When finely disseminated ores are ground to liberation, however, conventional desliming of the fully dispersed pulp results in an excessive loss of valuable constituents. Selective flocculation of iron oxides followed by removal of dispersed siliceous slimes is a new development and is one of the most promising approaches to the treatment of finely disseminated, oxidized iron ores, available in vast quantities both here and abroad (1,2,3). To apply selective flocculation to the variety of refractory iron ores or to cope with the fluctuations in an individual ore and the make-up water, the factors governing this technique must be clearly formulated. For the removal of siliceous and clayey slimes from oxidized iron ores by selective flocculation, the optimum conditions are extremely sensitive to the mineralogical characteristics of the ore, the type and the amount of soluble salts in pulp solutions, and the mesh-of-grind. Certain starches appear to function better than others (4, 5). Selection of the proper reagents and their judicious use is important not only for their efficient utilization but also for minimizing the adverse effects they might exert on the flocculation and flotation steps, and the pollution the effluents might cause when discharged, either intentionally or accidentally, into lakes and streams. In the present article some of the major factors that influence the selective flocculation of iron ores are summarized.

Jan 1, 1979

By A. F. Banks

INTRODUCTION Selective flocculation-flotation as a method of desliming potash flotation feed has been practiced in the Cominco Ltd. potash plant since November. 1974 when it was installed to replace a less efficient mechanical desliming process. The plant was designed for a consistent feed containing 4.5% insolubles. In practice the quantity and quality of the insoluble material is quite variable. This variability led to serious problems in the deslime circuit and consequently had an adverse effect on sylvite flotation performance. A costly mechanical solution to the problem was being seriously considered when it was drawn to our attention that a selective flocculation-flotation process had been developed. The process was tried first in the laboratory on the Cominco Ltd. ore, then on a pilot basis on 25% of the mill feed and finally full scale. The time from being informed of the process to full scale operation was 18 months. It has since been incorporated into a tailings regrind circuit. The original mine design called for the mining of an 11 foot height up to the top of the three clay seams. These had to be taken as they were a zone of structural weakness. It also assumed that the beds would be uniform with only a few disturbances. Very soon after the initial start up it was found that permanent openings had to take in the layers right up to the upper clay seams and because of the mining process that this material would have to be milled when encountered. The number of disturbed areas in the mine is greater than the design anticipated. In operation the insoluble content of the mill feed varies from 4.5% to 8% plus with the peaks being very short- term to relatively long, from hours to day. In terms of quality, the insolubles in the mining horizon are relatively soft and easily liberated, whereas those above are hard and liberate slowly.

Jan 1, 1979

By A. F. Banks

INTRODUCTION Selective flocculation as a method of desliming potash flotation plant feed has been in commercial use since November, 1974.l It was installed to replace a 1ess efficient mechanical desliming process. While most plants operating in the Saskatoon area of Saskatchewan were designed for 4% to 5% insolubles in practise the quantity and quality of the insoluble materials in the ore has been variable. The variability of the ore has contributed to less than optimum efficiency in the desliming and consequently, the potash flotation circuits. This lower than expected efficiency contributed to the commercialization of a patented process2 through large scale pilot plant testing. Referring to published information and experience, the application of selective flocculation-flotation of slimes to sylvinite ores will be compared with the more conventional mechanical methods of desliming. THE ORE The ore beds being mined in the Saskatoon area of Saskatchewan have proven to be much less uniform than originally thought (Figure 1). The insoluble content of the plant feed is variable in both quantity and quality due to two factors, the presence of disturbances and the structural weakness of the mud seams immediately above the ore beds. Some alteration of the insolubles in the vicinity of disturbances has made them more difficult to liberate and makes ore from the disturbed areas less amenable to treatment.

Jan 1, 1980

By R. Chanchani

It was reported earlier that francolite and dolomite from south Florida deposits cannot be selectively floated using conventional conditioning with sodium oleate as the collector. However, dolomite could be separated from francolite if the minerals were first conditioned at pH 10 followed by reconditioning at a lower pH. An optimum separation was achieved after reconditioning at a pH below 4.5. Reconditioning pH and collector concentration were determined to exert a major influence on the selectivity. Flotation, adsorption, and transmission infrared spectroscopic results are presented to elucidate the mechanisms underlying the observed selectivity.

Jan 1, 1986

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut, and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States, 2 and in addition, feldspar is produced as a byproduct by firms whose major products are spodumene and mica. 3 Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan, and the USSR. According to the US Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 and 2,514,000 t, respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel, tile, and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, NC, have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water containing 0.9-1.0 ppm fluoride will seldom cause mottled enamel on children's teeth; and for adults, concentrations less than 3-4 are not likely to cause endemic cumulative fluorosis and skeletal effect. Although the literature on this subject is rather confusing and inconclusive, the inference that concentrations over 4 ppm may affect bone structure is clear. According to the recent Federal Register,4 maximum fluoride level of 1.4 ppm at 79°-98°F is considered to be adequate and safe for the protection of health of the consumers. The EPA and state environmental agencies have accelerated their drive to reduce water pollution on a faster schedule. By 1977, the EPA specifications for maximum contaminant level of fluoride ions in the discharge waters of feldspar milling operatins is expected to be reduced to 2.0 ppm. The other problems of using hydrofluoric acid are the following: toxicity, hazards of handling and storage, and high cost as compared to other inorganic acids (almost 16 times the cost of sulfuric acid). In order to reduce fluoride levels in mill discharge waters, mining companies have taken the following steps: I) Recirculating a part of their mill water. Even though recirculation of mill water seems to be a novel method of reducing fluoride contamination of the discharge water, there are certain operational and handling problems. 2) Conducting research on the treatment of fluorides in mill waste water. The technology of treatment of fluoride ions has received considerable interest in the recent years. A recent research report5 estimates that the cost of fluoride ion removal to meet the present specifications in the feldspar industry is approximately $0.25/t of ore processed, and about $0.50/t of feldspar produced. At the request of the feldspar producing industries in North Carolina, the North Carolina State University (NCSU) Minerals Research Laboratory has taken up a research program directed towards overcoming the fluoride ion pollution problem. After a close study of the operational, technical, and economic aspects of feldspar flotation, it was decided to attempt to replace the conventional hydrofluoric acid process. Conventional Feldspar Flotatin Using Hydrofluoric Acid Since the inception of the feldspar flotation process using hydrofluoric acid by O'Meara2,6 the process has achieved a great commercial success. In the conventional flotation separation of feldspar-quartz, hydrofluoric acid is used to suppress quartz and activate feldspar, and a long chain amine salt (acetate or chloride) is used as a collector. The bulk of amine collectors used in current feldspar operations are applied as the water-soluble acetates of the free-base amines. These products are pastes or waxy solids which are available in a range of acetic acid neutralization levels generally 50 to 100% neutralized. In spite of the problems mentioned in connection with the use of hydrofluoric acid, this process is extremely stable with respect to changes in the process variables. With the exception of a few operations, alaskite and pegmatite are the major sources of feldspar.7 In the flotation treatment of a pegmatite that contains iron-bearing minerals (heavy minerals), mica, feldspar, and silica, a logical order of removal presents itself considering the following:8 1) Mica is readily floated by an amine collector in a pulp pH 3.5. Some iron-bearing minerals will usually respond to amine collector in acid circuit with the mica concentrate. 2) Since iron minerals tend to occur invariably in the feldspar concentrate, it is desirable to remove most of these prior to feldspar flotation. A fatty acid or a petroleum sulfonate collector used in this flotation step in acid circuit will float iron-bearing minerals. 3) Using hydrofluoric acid to maintain pH of 2.5, an amine collector employed in a final step will float feldspar away from silica, usually leaving the latter in the tailing as a high-grade silica concentrate. The problems connected with the flotation separation of feldspar-quartz arise due to the similarities in their chemical structure. Therefore, any reagent system that is likely to succeed in feldspar-quartz separation should have adsorption affinity towards one of the minerals and depression effect towards the other mineral.

Jan 1, 1979

By S. Ramachandran, L. A. Vazquez, N. L. Grauerholz

A novel process is described for the selective flotation of scheelite from low-grade (- 0.5% W03) tungsten ores having appreciable quantities of calcareous and siliceous gangue minerals. Specifically developed for the Tempiute, Nevada facility of Union Carbide, the process yields tungsten concentrates exceeding 15 percent W03 with at least 85 percent recovery. This condition was not achieved through conventional processes. This process consists of conditioning the ore pulp with judicious amounts of lime, followed by soda ash and sodium silicate as modifiers. The scheelite is then floated using a mixture of oleic and naphthenic acids as collector. Contrary to the common observation as to the deleterious effects of calcium in fatty acid flotation systems, lime addition is found to be beneficial in achieving satisfactory results. The process has also shown excellent results on a Brazilian scheelite ore.

Jan 1, 1976

By James B. Duke, Ernest W. Greene

An idea of what is meant by "Ultrafine Minerals Or Slimes" as used in the title can be had by an examination of Fig. I. Particle size distributions are presented for a crude kaolin clay, a coarse fraction and a fine fraction. The crude kaolin as mined was blunged with water, degritted through a 325-mesh Tyler screen, and dispersed with sodium silicate. The dispersed crude was then centrifuged in the laboratory into the coarse and fine fractions shown in the figure. The distribution curves were obtained by the well known sedimentation technique of Casagrande' using a long arm centrifuge to obtain equivalent spherical diameters down to 0.2 microns on the finer fraction. Fig. 1 shows the coarse fraction kaolin to be 50% finer than 3 microns, while the crude kaolin is 50% finer than 1.4 microns, and the fine fraction 50% finer than 0.6 microns. For comparison 53 microns on the horizontal scale would represent Stokesian diameters which would just pass a 325- mesh Tyler screen, taking into consideration the Andreasen sieve correction factor of 1.22 X the screen opening.' Another helpful comparison is the surface areas, which in square meters per gram, are 0.044 for 53 micron particles, 0.77 for 3 microns, 1.65 for 1.4 microns, and 5.0 for 0.46 micron particles. Fig. 2 is an electron micrograph of a similar fine fraction kaolin showing the hexagonal plate- like particle shapes.

Jan 10, 1962

By L. S. McNickle

Commonly accepted maintenance methods are being outdated by the rapid acceptance and use of more complicated hydraulic circuitry on modern mining equipment. It is no longer adequate to use the maintenance program to merely repair or sustain equipment operation. Ever increasing operating costs place a huge premium on lost production time. It has, therefore, placed the maintenance programs in the position of being required to alleviate equipment malfunctions on production shifts and still attain the maximum unit life from each component part. Ireland mine of Hanna Coal Co., which operates two production shifts and one maintenance shift per day, performs hydraulic maintenance with a plan that is geared to assure the bulk of work being handled on the midnight or maintenance shift. Production is thus allowed to continue without interruption from major hydraulic component malfunction. The plan is called selective maintenance because the specific part to be worked on and the time the work is to be accomplished are selected according to a definite plan.

Jan 10, 1961

By Harry L. McNeill

THE Selective Media Process was developed by the author in a laboratory provided by The Steårns-Roger Manufacturing Co. It is the outcome of an [ ] investigation into the possibilities of coarse beneficiation by sink and float without using the conventional heavy media. Commercial work to date has been limited to the treatment of minus 3/8-in. iron ore at the Hill Trumbull washing plant of the Cleveland Cliffs Iron Co., at Calumet, Minnesota. Two cut away prints of the machine are shown (Figs. I and 2). A rotary conical impeller is mounted within a stationary cone (Fig. 2). This impeller is adjustable vertically by a 12-ton screw jack. The speed of the impeller can be varied from 14 to 32 r.p.m. by the Reeves variable-speed motor pulley mounted on the 7 ½ -hp. motor drive. Attached to the bottom of the stationary cone is the automatic control valve for sink product, actuated by a ¼ -hp. gear motor. The sink product is dewatered in a conventional drag driven by a 7 ½ -hp. motor and discharged onto an inclined conveyor containing from 6 to 10 per cent moisture. Two plants are operated at the Hill Trumbull property. All the ore is first treated in a typical washing plant (Fig. 3). When treating "wash ore" a finished concentrate can be produced by the log washers and Akins classifiers, as the separation involves only fine silica (minus 48-mesh) and free iron. However, when "jig ore" is fed to the washing plant the coarse

Jan 1, 1946