Search Documents

By N. F. Dyson, T. R. Scott, M. R. Thornber, W. E. Ewers, M. Bussell

Leach liquors derived from the processing of nickel ores are generally highly contaminated and contain appreciable free acid. Methods are described for obtaining a commercial grade of concentrate from such solutions using pyrrhotite as the seed material to abstract nick- el, cobalt, etc. from solution. At temperatures in excess of 160° C., recoveries of 99% can be obtained from contaminated solutions where the free acidity is as high as 0.5 M in sulphuric acid. At lower temperatures down to 80° C., high recoveries can also be obtained either by adding H2S to the system with appropriate adjustment of the free acidity or by using "activated" pyrrhotite or artificial FeS in the system without prior addition of H2S. The methods are applicable to liquors derived from either oxide or sulphide ores, and the products are suitable for smelting or other known processes used to obtain pure metals. The mechanism of the reaction appears to vary with the operating temperature, and the results ye therefore discussed in the light of electron probe and optical microscopic studies.

Jan 1, 1973

By J. B. Sellers, G. R. Haworth, P. G. Zambas

Rock mechanics research was carried out in the Anvil Points mine, Rifle, Colo., in the period 1964-1968, with the dual purpose of providing oil shale to the retorts of six major oil companies and to perform research on mining cycle operations to maximize extraction under safe conditions. An 80% extraction ratio within the mining area proved feasible. Test results provided data on optimum pillar and roof design. Studies of mine orientation showed that the mining headings should take into account the prevailing joint patterns and also the directions of the principal in-situ stresses acting in the region.

Jan 1, 1973

By R. V. Ramani, Robert Stefanko

The more stringent ventilation requirements of the 1969 Act have created a greater need for improved network analyses. More air is required at the last open crosscut (9000 cfm) and for the first time a minimum quantity is specified for the face (3000 cfm). Severe restrictions are placed on both belt and track haulage, and the intake air cannot contain more than 2 mg per cu m of respirable dust, to be reduced to 1 mg later. Larger tonnage and longer life mines are the trend today, necessitating multiple fans and shafts. Yet relatively little engineering goes into designing the mine ventilation system. In this paper a ventilation system is designed for a typical Pittsburgh block system, manual calculations are made and then checked by a computer solution. The computer is the ideal tool to try out proposed changes on paper to insure that the entire mine is properly ventilated and no costly adjustments need be made by dumping air. While it is theoretically possible to solve complex ventilation network problems by hand, it is not practical to do so because of the tremendous man-hours required and the many opportunities for errors. Thus the digital computer is indispensible to the ventilation engineer and newer improved ventilation programs are being developed to more realistically model mine ventilation networks. Suggested ventilation changes to comply with the new regulations are also critically evaluated.

Jan 1, 1973

By E. Peters

As in other fields of Extractive Metallurgy, Hydrometallurgy is preoccupied with separation processes and with oxidation-reduction processes. The physical chemistry of each type of process can be described in terms of thermodynamic equilibria and in terms of reaction kinetics. Reaction kinetics are much more important at the low temperatures limiting hydrometallurgical processes than in com- parable pyrometallurgical operations and the number of cases in which the kinetics can be described by simple liquid-phase mass-transfer models are sharply limited. It is convenient to subdivide the applicable rate phenomena into processes in which (a) interface reactions control the rate,(b) mass transfer processes control the rate, (c) solid state process affect the rate, (d) thermodynamically predicted phase changes or molecular reactions fail to take place, (d) metastable substances or supersaturated phases persist, and (elchomogeneous reactions in solution affect the chemistry and the kinetics. Examples are drawn from the unit steps of leaching, cementation, hydrogen reduction, and electrowinning.

Jan 1, 1973

By L. G. Austin, P. T. Luckie

The Bond Work Index has been used for many years to estimate the power requirement of a material with known work index. The index is determined by a completely empirical test and no logical base for its use has been formulated. However, consideration of grinding as a unit operation which can be mathematically treated offers the prospect of considerably more accurate design and mill power estimation when sufficient data on large-scale mills becomes available. The interrelation of the Bond type with the unit operation approach is discussed.

Jan 1, 1973

By P. D. Bush, E. H. Gates, M. D. Vijayaraghavan, L. F. Engle

The process developed over the last few years by Republic Steel Corporation in conjunction with Colorado School of Mines Research Institute has been used as a basis for the conceptual engineering of full size plants. The paper will cover the equipment design criteria, equipment design itself, and the integration of the complex unit operations. There are unique features of agitation and use of gas media through- out. The paper will provide an illustrative example of the process requirements for a variety of raw material feeds. It will discuss the materials of construction approach required.

Jan 1, 1973

By J. B. Sellers, G. R. Haworth, F. W. Brackebusch, P. G. Zambas

Results of large-scale mining experimentation carried on in Stage II of the Anvil Points Oil Shale Research Program, Rifle, Colo., are reported. After a new adit was excavated, over 500,000 tons of oil shale was extracted during a 13-month period by a modified room and pillar method. Experiments in drilling and blasting headings, benches, and crosscuts are reported. Roof-bolting procedures, loading and hauling, and ventilation design are discussed. Results of the extensive investigations carried out by the cooperative industry group and earlier work by the U.S. Bureau of Mines indicate that mining oil shale is technologically feasible.

Jan 1, 1973

By F. G. Miller, J. M. Podgursky

Laboratory and pilot plant work on tabling of 14-mesh X 0 hydrocyclone under flow are summarized. Included are: operating principles of hydrocyclones and tables; performance of these two devices, separately as well as in combination; comparison of the combination hydrocyclone-table system with other fine-coal processing systems; and application of the hydrocyclone-table system in fine-coal circuits. The data show that the table actually compensates for the shortcomings of hydrocyclone and makes a combination table-hydrocyclone system attractive, particularly in those cases where fine pyrite is one of the major contaminants.

Jan 1, 1973

By Robert M. Lewis

At the Scotia plant of Blue Diamond Coal Co., near Cumberland Ky., good recovery and grade can be obtained when floating deep mine coal. When the plant changes over to strip coal, flotation fails, resulting in loss of coal. A procedure was developed at the Minerals Research Laboratory in Asheville, N. C., for recovering strip coal by flotation. Laboratory results were duplicated on a batch scale at the plant. The procedure was found to be effective when tried on a continuous basis in the processing plant.

Jan 1, 1973

By D. A. Rice, R. L. Stone

Studies of the possible effect of plant water chemistry on the strength of unfired iron ore pellets apparently have not been reported in the literature. Naturally occurring soluble salts were removed from magnetic concentrate filter cakes obtained from several iron ore concentrators. Laboratory balling tests showed that unfired pellets made from these "clean" filter cakes were 50-100% stronger than the usual unfired pellets containing the salts. The fact that certain chemical additives dissolved in the water used for balling "clean" concentrates decreased the strength of unfired pellets indicates that salts in the plant process water may be responsible for lower strengths. According to chemical analyses of plant process waters at these plants, calcium and magnesium are probably the most detrimental salts in the plant circuits. It is suggested that calcium, magnesium, and other polyvalent cations in the mill process waters ion-exchange for lower-valence cations in the bentonite and thereby destroy the electrostatic-charge bonding in the green pellet. Some practical guidelines are also included for plant balling practices.

Jan 1, 1973

By K. D. Hester, A. C. Anderson

The Elliot Lake uranium deposits are contained in a pebble conglomerate which is similar throughout the basin. This paper compares the solid-liquid separation circuits of two nominal 3000 T/d acid leach uranium concentrates treating Elliot Lake ore. One concentrator employed rotary vacuum drum filtration for solids removal and washing, the .other used counter current decantation in torque arm thickeners. Capital and operating costs, operation and maintenance, and metallurgical performance of the two solution recovery methods are compared and contrasted. A recent development, removal of the sand fraction ahead of C.C.D. and separate sand washing in hydraulic cyclones, is also discussed.

Jan 1, 1973

By David R. Maneval, Sylvester Lemezis

All acid mine drain waters, regardless of source, share certain characteristics; but they do differ in exact chemical composition, degree of acidity, and total solids content. Any serious program to treat such waters must recognize these differences and apply to each specific case the technique which offers the best promise of each specific case the technique which offers the best promise of technical and economic success. The Pennsylvania Dept. of Mines and Mineral Industries has originated and funded studies of many different treatment means. Neutralization with lime is now being used on 200 different polluted streams in Pennsylvania, and multistage flash evaporation has been selected for a particularly large and troublesome outfall near Wilkes-Barre, Pa. A 5 x 106 gpd plant for this latter site is now being designed by Westinghouse Electric Corp. which developed a concentration process based on multistage flash evaporation as part of the State's research program.

Jan 1, 1973

By Frank L. Gaddy

Falls of roof account for over 50% of the fatalities that occur in coal mines in the U.S. Thus, roof control is one of the more important phases of underground mining. In reality, the control of roof influences the system of mining and is a major determinant of the width and spacing of working places, operations at the mining face, ventilation control, and surface subsidence. Frequently, the control of roof is the largest single cost item. Roof control is a never-ending task, not only at the working face and throughout sections where men are working, but along haulways and airways that must be maintained for the life of the mine. This is because roof, even the best of roof, slowly deteriorates, so it must be frequently examined, with corrective support applied when needed. As coal is excavated, stresses are set up in the roof became the previous equilibrium is upset, resulting in pressures that cause fractures and slight, movements that are, frequently, hard to detect. Unless the immediate roof, in the excavated area, is given support by artificial means, it might fall or there might be a succession of falls, varying from a thin scale to several feet, depending on the nature of the top. Exceptions to this are those rare mines, or sections of mines, with hard, strong, nonweathering roof that requires no support. GENERAL CLASSIFICATION OF ROOF There are two broad types of roof as far as support is concerned, the immediate roof above the coal and the main roof. Artificial support for mining purposes is only concerned with the immediate roof as nothing except large blocks of solid coal, or massive concrete, will support the main roof. The immediate roof is generally a few feet thick but can vary from inches to 20 ft or more. There are examples of where there is no immediate roof as the massive main roof lies directly on the coal bed, but this is rare. Impossibility of supporting the main roof and all of the cover

Jan 1, 1973

By John W. Tieman

Coal is a term applied to vegetable matter which, through geological processes of heat and pressure, has had both its physical and chemical properties changed. Because its chemical composition is variable, geologists classify coal as a rock rather than a mineral. Peat represents the initial stages in the development of coal, although not classified as coal itself. PHYSICAL PROPERTIES OF COAL The physical properties are concerned with the characteristics of coal in its natural state, or prior to its end use as a fuel. For example, the hardness of coal determines the maintenance cost on coal handling equipment; the specific gravity of coal determines the coal preparation techniques used in a cleaning plant as well as the capacity of coal bins, boats and size of cargo, and other coal storage facilities. The physical properties are, of course, dependent upon the chemical constituents that make up coal, and thus all properties are interrelated. Specific Gravity The specific gravity of a body is the ratio of the weight of the body in air and the weight of an equal volume of water. The specific gravity of pure coal ranges between 1.25 and 1.70, generally increasing with rank. The most important use of this physical characteristic is the part that it plays in the cleaning of coal by wet wash methods. The basic principle on which these operate is that the specific gravity of coals differs from their associated impurities and that there is a relationship between the velocity of the fall of particles in water and their density. Since the specific gravity of slate is around 2.5 and pyrite is about 5.0, pyrite and slate will fall to the bottom of a container filled with water more rapidly than coal. If the water is given a pulsating motion by

Jan 1, 1973

By H. V. Fairbanks

Efforts were made to determine the amount of increase in the drying rate which could be obtained through acoustic treatment of ultra fine coal under various conditions, and to test the feasibility of using a rotary kiln and multitiered vibrating screens as a means for continuous drying of coal fines. Introduction of acoustic energy during the rotary kiln experiments increased the drying rates from 10-40%, depending upon the experimental condition. The use of a drying assembly consisting of multitiered vibrating screens produced better results than the rotary kiln and has definite possibilities of providing an effective means of drying coal fines in relatively large quantities.

Jan 1, 1973

By C. A. Kroetz, A. J. O’Neal

The Long Island Lighting Co. has operated an extensive monitoring system for over three years. Nearly 900,000 separate pieces of information have been recorded for a land area of some 600 sq miles, 15 miles north to south by 40 miles east to west. The data are composed of about a half million sulfur dioxide measurements at various locations, 290,000 of which were by the West-Gaeke method, about 160,000 pieces of weather data, and 220,000 measurements of sulfur dioxide as emitted from each of the power plant stacks on the system, all measured on an hourly basis and stored on computor cards and tapes. The computor has been programmed to collate stack emissions, weather information, and ground level sulfur dioxide measurements. The analysis shows that emissions from tall stacks do, indeed, contribute very little to ground level sulfur dioxide. For example, LILCO shows that its Northport plant contributes less than 2 ppb, hourly annual average. They also state that the plant converted to 100% natural gas or shut down, would reduce ground level sulfur dioxide by no more than 2 ppb.

Jan 1, 1973

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By J. J. Predali, J. M. Cases

J. J. Predali and J. M. Cases (Attachè de Recherche and Charge de Recherche, respectively, Centre de Recherches sur la Valorisation des Minerais, Institut Polytechnique de Nancy, Nancy, France)-The role of CO, in carbonate flotation is one of the parameters of a complex phenomenon: the adsorption of salts of fatty acids onto minerals. The authors therefore must be congratulated for their work. Their experimental results suggest some questions: 1) Recovery with C02, benzoic acid, or HCl, look very similar [(Fig. 1)] to that with the use of air; however, the recovery decreases very slightly (<10%). But in these two kinds of experiments, two parameters are different: the pH which is near 5.8 (with C02) becomes 9.1(without C02) and the concentration of Ca* I x 10-3 mole per 1 (without C02) becomes 1.9 X 10&apos; mole per 1 (without COO. 2) Adsorption experiments (Fig. 2) permit computing the surface coverage 9 which is 7.4% (without C02) and 8% (without CO_.) for an initial concentration of 12 X 10-6 mole per 1 in sodium oleate. It seems doubtful to us that this small variation can produce large increases of the recovery in flotation. 3) It is difficult to correlate adsoption and flotation experiments because they do not seem to have been done with the same size of particles. The concentration needed to obtain 95% recovery (Fig. 1) is about 3.0 X 10_" mole per l, that is, 1.13 X 10-6 mole for about

Jan 1, 1973

By G. G. Waddell, T. J. Crocker, S. S. M. Chan

A successful engineering structural design often depends upon a thorough understanding of the material properties of the structure. It is no exception when designing a supporting system for stable underground openings. For this reason, studies were made in the deep mines of the Coeur d&apos;Alene mining district to obtain engineering properties of rocks and rock masses immediately surrounding underground openings. In this paper, data concerning laboratory tested physical properties of rocks and in-situ deformation behavior of rock masses from the Galena, Lucky Friday, and Silver Summit mines of the district are presented. Interpretations of the data so obtained and suggestions for the use of the results of the investigations as design criteria are also outlined.

Jan 1, 1973

By Renato G. Bautista, Gary A. Beetner, Anthony L. Frey

The flow of material in a pump mixer-settler extractor was studied photographically and visually by injecting dye into the equipment and following its advance through the various sections of the equipment. Volumetric measure of the flow was obtained from analysis of the photographs. The organic portion of the settling chamber, the fluid surrounding the pump mixer, and the pump mixer itself were found to be operating in plug flow. The aqueous portion of the settling chamber was found to be partially mixed. Significant dynamic effect was noted due to density changes in the feed streams. The quantitative and qualitative observations made of the flow within a single stage should be of value in predicting the flow patterns in all similar equipment, including opaque and liquid metal solvent extraction systems.

Jan 1, 1973