Search Documents

We wish to congratulate the authors on a fine presentation of a difficult and interesting problem. We fully support the findings that liquid or even mushy center reduction has no place in the production of quality steels. We also agree with the findings, or implications, that internal bar quality is not made in the rolling stands, but in the caster. This is the main reason why Inland caster exclusively uses the submerged casting technique after a few months of familiarization with open casting. The metallurgical advantages of combining in-line reduction with a caster are actually indirect. The use of submerged casting and refining powder permits casting of fine grained aluminum killed steels without resorting to expensive grain refiners and cuts down or eliminates reoxidation during casting. Immersion of a snorkel into a small mold may lead to several operating difficulties. Hence, the presence of in-line reduction enables the section to be cast into a large mold, at high output rates, while obtaining some product size flexibility. The capital and operating costs of a caster-- in-line mill are lower than those of the traditional installation with a separate reheating furnace and billet mill. Admittedly, in-line reduction represents an additional challenge to the steelmaker, maintenance man, and metallurgist.

Jan 1, 1972

By Earle J. Klohn

Mining operations have been carried out in British Columbia since the time of the first settlers in the area. The early developments were mainly small volume, high-grade operations, producing small quantities of tailings wastes. In these early days the nearest stream was a logical first choice for tailings disposal. Where streams suitable for accepting the tailings were not available or where streams crossing the International Border could not be used for this purpose, the nearest convenient land site was selected for storing the tailings. Old tailings waste piles exist at many locations in the Province and are readily evident, for example, in the Princeton and Hedley areas. Figs. 1 and 2 are photographs showing the present condition of two of these old tailings dams. [ ]

Jan 1, 1972

By Oscar M. Wicken

Industrial minerals - being the basic materials for much of the industrial activity in the world -suffer or gain in the market place with changes in that activity. The period 1970 and early 1971 has been one of little growth in many of the mineral-consuming industries, particularly those associated with building and construction. Consequently, the production of many commodities revealed little or no increase above 1969 levels. The pick-up of construction activity in the last half of 1971, however, is expected to be at an intensity which will result in an over-all good year; for example, cement shipments may, establish a record. Some industrial minerals products that bucked downward trends were those allied with the agricultural industry. Phosphate rock shipments increased, particularly from Florida which contributes over 400/c of the phosphate rock in the western world. Potash had higher sales and production for the third straight year, which means that inventories are being eased. The catch-all term of ecology is an oft-mentioned theme among industrial minerals suppliers. Specifically, the need for control of dust emissions is adding a heavy capital investment burden to many of the producers; such a burden, in fact, that plants have had to cease operations because the cost of dust collection equipment could not be born. As an order-of-magnitude estimate, dust collection equipment for cement plants can run $2-3 million for a single plant; some estimates are that the total cost of dust collection equipment in a new plant can be approximately 20% of total investment. All minerals processers have dust control expense of greater or lesser proportion.

Jan 1, 1972

The writers are to be congratulated for their excellent paper on a subject dear to the hearts of manufacturers of cold rolled sheets. Gary Works produces rimmed steel ingots up to 53,000 pounds teemed 91 inches high in 31 x 84 inch molds. By the writers' definition, this puts us in the small mold category, and a comparison of their adopted melt shop practice with our established rimmed steel practice discloses not a dime's worth of difference between us. This should give comfort to the writers for we at Gary have- never encountered the frequency of white line rejections as described in their paper.

Jan 1, 1972

By Wayne C. Hazen, James K. Kindig

As the complexity of hydrometallurgical systems increases, it offers new opportunity for applications of solvent extraction. However, the high capital cost of mixer-settlers for large flow rates is a drawback to wide application in base metal recovery. This paper presents information on the use of cyclone separators in place of settlers with attendant significant reduction in capital cost. Various flowsheet possibilities for this development are discussed.

Jan 1, 1972

By Kermit Allen

Historically, major natural gas transmission companies have been faced with the problem of meeting peak demands when the source of natural gas is located hundreds of miles away from the marketing area. Transcontinental Gas Pipe Line Corp.'s position was further complicated when offshore gas supply wells were shut-in during hurricane alerts. Transco's solution to this problem was the construction of salt storage wells adjacent to their pipeline near Eminence, Miss. Storage caverns were constructed using conventional solution mining methods. Two 13 3/8-in.-diam cased wells were completed and a 1,000,000-bbl cavern was leached at an interval of 5700 to 6700 ft at the base of each well. The two caverns have a usable storage volume of 2.0 billion cu f t and each well has a deliverability rate of 375 million standard cfd. The caverns are unique in that brine is not used for product displacement-all brine has been removed from the caverns. Natural gas is stored at a maximum pressure of 4000 psia. During withdrawal the cavern pressure drops to a minimum of 1225 Asia-the volume of gas between these two pressures becomes "usuable or top gas." The Eminence storage terminal is located on the Eminence salt dome about 30 miles north of Hattiesburg, Miss. Construction began in July 1968 and was completed in October 1970.

Jan 1, 1972

By Fun-Den, Wang

An open pit rock structure usually contains geological planes of weakness. They are formed by joints, faults, bedding planes, fractures, and cleavages. Rock slope failures often occur in the form of sliding of rock blocks along a plane or several planes. Such a rock block has three- dimensional geometry, and consequently a vector method of analysis has been found useful in evaluating its stability. Rock blocks of a tetrahedral shape with one free surface have been analyzed by Londe. Rock blocks formed by sets of parallel joints have been analyzed by Wittke. The present chapter presents the analysis of rock blocks formed by planes of weakness of arbitrary orientation, and of three-dimensional geometry.

Jan 1, 1972

By J. Koskinen, P. Vanninen, T. Leskinen, A. Leppala

Continuous and accurate analysis of slurries has become a critical requirement in mineral processing. With on-stream assay data, automation procedures can be employed to obtain higher recovery and improved control of production. The Courier system was developed by Outokumpu Oy, taking advantage of mineral processing know-how, to provide means for achieving these objectives in the company's ore concentrator operations. It became evident, based on early experience with on-stream analysis, that the Courier should be a complete system to fulfill all functions of the analysis operation. The system includes equipment and techniques for primary sampling, sample preparation for assaying, and processing of data for final assay results. In addition, the on-line X-ray spectrometer unit was developed specifically for industrial use, incorporating a number of technical advances. A new system for converting spectrometric data to assays is based on a physical model programmed on a digital computer. The Courier system is furnished on a turn-key installation basis incorporating all elements needed for operation including calibration. The experience to date with the Courier system at the Pyhäsalmi concentrator is summarized. Reference is also made to recent results with installations at the Outokumpu and Vihanti concentrators.

Jan 1, 1972

By W. H. W. Husband

Rock salt has been solution mined for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the same method. However, only Kalium Chemicals Ltd. has been successful, possibly because the conditions in Saskatchewan are the most favorable to be found so far for the development of a solution-mining method for potash. In view of the fact that few studies of solution mining of potash have been attempted, only one company has succeeded in using the method, and no information has been released by this company, the application of solution mining of potash ore bodies has to be presented on the basis of available theory, past small-scale studies, and recent patents. A simple mining method is outlined and possible methods of recovering the potash from the brine are discussed. Dissolution data pertaining to solution mining of potash, flowsheets, and material balances are presented. The available information is brought together in a cost analysis to show capital and product costs in terms of 1966 dollars.

Jan 1, 1972

By Jay F. Smith

The Alan Wood BOF Shop consists of two 140 ton furnaces with a rated yearly capacity of 1-1/4 million ingot tons, he hot metal for the BOF Shop is supplied by two 18 foot blast furnaces which produce an average of 2000 tons per day, To achieve the rated ingot ton capacity with this limited supply of hot metal, the preheating of scrap is necessary. This is accomplished in the furnace by using an oxygen-natural gas burner. Piping Arrangement The natural gas and oxygen are piped into the Shop through 8-inch lines to their respective valving stations. As can be seen from Figure 1, the flow of natural gas passes through a flow control valve which is common to both furnaces, after which it divides into two 6-inch lines forming two identical and independent gas control lines, one for each furnace.

Jan 1, 1972

By J. Marshall Rounsevell

It is probably not too far from the truth to say that the sulfur content of the steel bath at the first turndown of the basic oxygen furnace is influenced by every factor which varies in the operation of a BOF shop. However, the determination from normal shop operating data of the effect of a given factor on turndown sulfur content requires a means for collecting a large quantity of such data and a significant variation of the factor in question in that data. In this paper, operating data from 4000 heats collected on the computer at Inland's No. 4 BOF Shop is utilized to analyze the effect of four operating parameters -- hot metal sulfur content, hot metal manganese content, percent burnt dolomitic lime (dolomite) in the flux charge, and the presence or absence of transfer ladle slag skimming -- on first turndown sulfur content.

Jan 1, 1972

By Richard L. Stowe, Donnie L. Ainsworth

The static, rapid, and shock-loading response of rock is of interest to many in the field of rock mechanics. For example, the effects of loading rates on strength and stress-strain characteristics of rock are quite important in defining input loading for use in the design of underground protective installations. Response data on rock subjected to shock loading over a wide range of pressures are also vital in the field of underground nuclear testing. In addition, material response is needed in design of shock-absorbing liners. A number of investigators have reported that ultimate compressive strength of rock increases with increased rates of loading.1-6 Wuerker3 stated that modulus of elasticity, obtained from sonic determinations, increased in some rocks by a factor as high as 4.5. It appears that only a limited amount of work has been done on comparing static modulus and modulus obtained from impact testing.6 Phillips4 showed that with increased rates of loading the deformation decreased. More recent work by Atchley and Furr5 showed that when moderate-strength concrete is stressed with increased loading rates, the axial strain at failure increased. One would expect this to occur if we think in terms of purely elastic materials. For example, if E is constant and maximum strength [amax], increases, the axial strain would also increase. However, in rock testing thus far we have worked almost exclusively with nonhomogeneous and inelastic rocks. From this fact alone the increase in axial strain with increased load application is noteworthy.

Jan 1, 1972

By M. B. Kahle, A. D. Pernichele

Four types of slope failures in waste dumps are recognized debris flow, foundation failure, edge slump, and blowout. The first three types, although at times causing considerable damage to property and interfering with mine operations, are not usually dangerous to personnel because of their slow rate of movement. The fourth type, the blowout, is the most dangerous because of its explosive mode of failure and lack of forewarning. The December 1969 failure at Verona dump is presented as an example of a blowout. Data from piezometer holes indicate that the blowout was due to perched leach solutions near the face of the dump. The level of water in this zone is very closely related to the rate of leach water application on the dump. A detailed analysis of core samples indicates that the impounded water was perched on a zonal accumulation of jarosite which is associated with a buried dump surface. Drain holes proved successful in controlling perched leach solutions in the critical zone near the face of the dump. Monitoring of the water level in the perched zone is considered essential in preventing blowouts. The use of drain and piezometer holes has allowed an increase in the rate of water application on the dump while preventing additional failure.

Jan 1, 1972

By George Newton

When Mr. Bailey asked us to present a paper describing our new BOF shop, he requested that we avoid a presentation heavily laden with detail and statistics. Not only have we attempted to do this, but also we have prepared a number of colour slides which, hopefully, will provide you with a graphic conception of the facility. The installation of the BOF facility at the Steel Co. of Canada's Hilton Works was delayed many years because of the remarkable production growth of the oxygen open hearth furnaces in No. 3 shop. However, in mid-1960 it became strongly evident that not only would increased ingot capacity be required, but also that N0.2 shop - with vintage non-oxygen open hearth furnaces - would have to clean its stacks in the near future, or be closed down. A decision to embark on the BOF facility was made in 1967 after an extended period of in-depth planning and assessment of industry trends.

Jan 1, 1972

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

By Wayne T. Brooks

The Occupational Safety and Health Act of 1970, although providing no precise definitions of safe and healthful working conditions, specifies mandatory duties, and methods and procedures -- "to assure so far as possible every working man and woman in the nation safe and healthful working conditions." The dynamics of the workplace ad the dynamics of this coextensive Act both spring from the same source. Both require at any given time an application of the then con- temporaneous highest state of the art. Both are flexible, ongoing, adaptive, changing; both advance by a blending of experience and research.

Jan 1, 1972

By J. E. McConnell

No. 1 Electric Furnace and Billet Casting Shop, located in Plant No. 4 adjacent to our new 12 inch merchant bar mill, represents Inland Steel Company's first venture into both electric furnace steelmaking and continuous casting. Construction of the shop began in September, 1968 with excavation and foundation work, followed by awarding of general construction and major equipment contracts from December, 1968 to April, 1969. The first heat was tapped from No. 90 furnace on December 18, 1970, and the first cast attempted on December 29, 1970. The rated shop capacity is 500,000 tons per year of semi-finished billets and blooms, and was justified on the basis of approximately 85 percent of the product mix falling into the special bar quality category of steel grades. Auxiliary equipment has been designed into the shop to pursue free machining steels, including leaded and tellurized grades. The start-up and operation of the shop for the first year was essentially based on a two-part philosophy: 1. Initially operate with the "open stream" casting technique to accomplish machine shakedown and operator familiarization and training. 2. Operate with special bar quality, or "submerged casting", practices, make necessary refinements and gain customer acceptance

Jan 1, 1972

By A. H. Tousley

Current problems in the cement industry are discussed and suggestions for solving them by modernization are made. Cement facility modernization is discussed in considerable detail with examples illustrating before and after conditions. Itemized are the improvements realized in better working conditions, better efficiency, higher production, lower costs, and better community relations. These improvements are related to the overall profitability of the particular plant or facility.

Jan 1, 1972

By Jonas Svensson

A new method is described for the production of cold-bonded pellets using a hydraulic binder, such as portland cement. Large-scale pilot-plant tests have proved that self-fluxing pellets of high reducibility and good handling strength can be made by the method. Blast-furnace trials have shown that the pellets are an acceptable burden material, comparable with self-fluxing sinter or heat-hardened pellets. Economic factors of commercial-scale production are discussed. The Grangcold Pellet Process—for which patents have been applied or already granted in a number of coun-tries—uses a hydraulic adhesive such as portland cement, slag cements, pozzolanic cements, etc., for the production of cold-bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron-ore fines is not new. Portland cement was proposed as an adhesive for cold-bonded iron-ore briquettes in patents granted more than 50 years ago.' In a report on the briquetting of iron-ore fines, published in Stahl und Eisen in 1959; it is stated that briquettes bonded with portland cement are used on a small scale at an ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft, and difficult to store and handle. The Grangcold Pellet Process has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrated during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus, the mixture can be stored in a stockpile or in a bin until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening. The binder preferred for the Grangcold Pellett Process is portland-cement clinker, ground without the admixture of gypsum in order to avoid sulfur in the pellets as far as possible. Usually a 10% binder content is used. Two-thirds of the portland-cement clinker consist of lime and the rest is silica, alumina, and ferric oxide. Thus, self-fluxing or overbasic pellets are produced with this binder if the amount of silica in the concentrate used does not exceed 4%. The Grangcold Pellet Process was developed by the mineral Processing Laboratory of the Granges Co. Work started in 1963 with batch-scale tests. In 1966, a small pilot plant was put into operation in which 1800 tons of pellets were produced using 10% of rapid-hardening portland cement as a binder. Favorable results from a blast-furnace test with this batch led to the decision to erect a larger pilot plant which went into production in the summer of 1967. Since then, approximately 100,000 tons of cold-bonded pellets have been produced, mostly with 10% gypsum-free portland cement as a binder. Several full-scale blast-furnace trials have been performed with the pellets. The results of the trials indicate that the Grangcold pellets constitute a satisfactory blast-furnace feed. An industrial plant for the production of Grangcold pellets with a rated capacity of 1.5 million tpy is now under construction at the Granges Co.'s mine at Grangesberg. The plant will come into operation in the summer of 1970. Results from Laboratory Work Pellets made from iron-ore concentrate bonded with portland cement harden slowly and their handling is very critical until they have hardened enough to loose their stickiness. It is therefore especially important to study the progress of the hardening action and the factors influencing it. This is best achieved by investigating the relationship between the compressive strength of the cement-bonded pellets and the curing time under varied conditions. The general course of this relation-

Jan 1, 1971

By Walter H. Ortel, George B. Wallace

INTRODUCTION A greater understanding is required about the factors which control tunneling operations if we are to meet the expected demand for tunnels. Much of the needed information can best be achieved by the proper use of instrumentation and advanced engineering concepts. Tunnel measurements and their analysis may prove to be the key which will give the insight necessary to understand the relationship of rock, tunnel supports, and linings. There are three main areas which can be improved through the use of tunnel instrumentation. First, and of prime importance, is safety for men and the project. When unstable conditions occur, sets become distorted. Even without measurements, it is sometimes possible to tell when trouble is approaching. In effect, the set acts as a load cell. Distortions in the set indicate reinforcements may be required to maintain stability. Additional sets or rock bolts, if they are placed soon enough, may provide this stability. However, when large rock displacements occur in short periods of time, it could be too late. Figure 1 is an example of the difficulties encountered in stopping moving rock. To stop the movement and possible failure, large props were placed above the spring line and the massive concrete gravity buttress was constructed along the legs. Rock bolts from the buttress deep into the rock were also used in an attempt to stabilize the rock mass. However, this work is for a highway tunnel and eventually these props and buttresses must be removed.

Jan 1, 1971