Search Documents

By J. M. W. Mackenzie

The interactions between oil drops and mineral surfaces have been examined for the cetyltrimethylammonium bromide (CTAB)-quartz and sodium dodecyl sulfate (SDS)-hematite systems. The results have been interpreted using a electrical double layer interaction model, a "sweeping-penetration" model based on steric interactions and a free energy of adhesion model. The adsorption of long-chain ions at the mineral interface was also studied and found to follow a Fuerstenau-Modi model of combined Coulombic and chain-chain interaction forces. The basis of the emulsion flotation process and the feature which makes it differ from conventional flotation is: encounter, followed by adhesion, between oil drops and mineral particles which are suspended in an aqueous environment. The manner in which the adhesion between these two phases contributes to the flotation process may be through the formation of min-eral-oil drop-mineral linkages, mineral-oil drop-air bubble linkages, or a combination of both. Possible flotation mechanisms derived from these adhesion processes are shown schematically in Fig. 2 while Fig. 1 shows an example of the first mechanism for quartz particles which have been floated using a cetyltrimethyl-ammonium bromide (CTAB)-Nujol emulsion as collector. In Fig. 2 the three phases, mineral, oil, and air, for convenience have been shown as having approximately equal size. This would not always be the case in an actual emulsion flotation operation. For the flotation of sand-sized particles of approximately 0.5 mm diam, the mineral particles would be at least ten times the size of the largest emulsion drops present in the system, while in the flotation of —10u slime particles, the mineral phase may be of the same order of size as the oil phase. The air bubbles in a flotation cell are normally about 1 to 2 mm in diam and therefore, in general, would be larger than the oil drops. Although the relative size of the three phases does not alter the basic adhesion processes between oil drops, mineral particles, and air bubbles, which depend on the physical and chemical properties of the interfaces involved rather than on the extent of these interfaces, it does alter the degree of deformation of the oil drops and air bubbles which will occur on adhesion. For mechanisms 1 and 2 to take place, the oil-water and mineral-water interfaces must be partially replaced by a mineral-oil interface while in mechanism 2 there is the additional requirement that the oil-water and air-water interfaces must be replaced by an oil-air interface. In view of the importance of the oil drop-mineral particle encounter and subsequent adhesion stages to both of the emulsion flotation mechanisms discussed, a study has been made of some physicochemical factors which control these processes for Nujol-cetytri-methylammonium bromide (CTAB)-quartz and Nujol-sodium dodecyl sulfate (SDS) -hematite systems. Experimental Electrokinetic Measurements.—The zeta potential of mineral particles was measured using a streaming potential technique similar to that described by Fuerste-nau.1 The streaming potential was measured using a multirange electrometer while the plug conductivity was measured using a 50 cycle sec1 bridge. Measurements were made on 28 x 65 mesh particles. Contact Angle Measurements.—A captive bubble technique was used to measure the contact angles for air bubbles and oil drops. The angles were measured on fracture faces of unmounted minerals which proved easier to clean than polished mounted specimens and should more closely represent a flotation system. Reagents: These have been described in a previous publication.0 Minerals: Rock crystal quartz from the New England district, N.S.W., was used for contact angle and streaming potential measurements. The quartz was hand

Jan 1, 1971

By David L. Riley

Organization The Foundling Years - 1901-1921 Two events that occurred in the decade of the 1870's have had far- reaching effects upon the petroleum industry in the U. S. and formed a basis for the birth and growth of the petroleum engineering profession. In 187 1 a group of mining engineers banded together to form the American Institute of Mining Engineers "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means". Although it was to be 30 years before an event in Jefferson County, Tex., would cause petroleum to come into prominence as the world's principal source of energy, the founding of AIME provided an organization through which the application of engineering to the recovery of petroleum and natural gas could be developed. In 1875, a Pennsylvania judge who was called upon to make a decision for which there was no precedent reasoned that oil and gas were like wild game - they belong to the man who can reduce them to possession. His decision sired the "rule of capture", which stated that a landowner possesses the oil produced from his well, even though it might have come from beneath his neighbor's land. This interpretation prevailed for more than half a century, during which time gold-rush tactics were employed in the drilling and production of many oil fields in the U. S. The resulting overproduction and tremendous waste led to a virtual economic collapse of the U. S. petroleum industry by the early 1930's. To bring these malpractices under orderly control, proration and conservation policies were developed, and petroleum engineering became the medium through which they were devised and implemented. At the turn of the 20th Century, more than 90 percent of this country's oil production came from the East, but the picture changed with dramatic suddenness on Jan. 10, 1901. Captain Anthony F. Lucas, an Austrian mining engineer, had noticed concentrations of oil and gas near salt domes during mining operations on the Louisiana Gulf Coast. In 1899 he leased a low mound near Beaumont, Tex., began drilling, and after almost 2 years of intermittent operations, brought in the famous "Lucas Gusher"

Jan 1, 1971

By Robert L. Greyer, John I. Myung

The Birdwell 3-D Velocity Log displays photographically the amplitude of elastic waves as a function of time and of the depth of the logging tool in a borehole. The elastic waves are generated by a magneto-strictive source transducer and detected by a receiving transducer, which is at a fixed distance from the source. The output of the receiver, which is proportional to the amplitude of the received elastic waves, modulates the light that exposes the film record. The duration of the receiving time can be selected to record the entire wavetrain of late events or to record only early events at a finer time scale. When a full complement of elastic waves (i.e., the refracted compressional wave, composite shear wave, direct fluid wave, and boundary wave) is recorded, their velocities and the density of the borehole fluid provide the information necessary to compute the elastic moduli and density of the rock surrounding the bore-hole. The differences between the values of the moduli determined from measurements of 3-D Velocity Logs and by other better known techniques are small, well within the limits of experimental error, when the velocity log is interpreted by an experienced seismic analyst. INTRODUCTION Quantitative descriptions of the mechanical properties of the rock environment have long been basic requirements of planning, design, and quality control of engineering projects. Because of this need, many techniques for determining the elastic moduli from static and

Jan 1, 1971

By Dennis V. D’Andrea, Joseph L. Condon

Laboratory crater tests were performed in two-dimensional plates and three-dimensional .blocks of Holston Limestone. Fractures in the blocks were exposed by sawing through the crater region, and a technique employing dye penetrants is described for examining the resulting fracture systems in both blocks and plates. Crater fracture patterns changed from extension of radial fractures to spa11 fractures parallel to the free face as charge depths were increased. The amount of fractured rock was found to be greater than the amount determined from standard crater volume measurements. Graphs and photographs illustrate these findings.

Jan 1, 1971

By George B. Clark

More economical methods of rock disintegration are needed for mining and for rapid excavation. Two major systems are drill and blast and mechanical excavation, including tunnel-boring machines. Current drill and blast methods are cyclic and there- fore limited in speed of operation. Boring machines are limited to moderately hard rock due to bearing and cutter wear. The recent development of ANFO, which has reduced blasting costs markedly, was largely fortuitous because of the method of manufacturing AN prills. New slurries and fluid explosives are easy to load and have high energy-pressure characteristics.

Jan 1, 1971

By John V. Beall

New York was bathed in pale winter sunshine and, surprisingly, coatless weather. The time was the AIME Centennial and 100th Annual Meeting. From advance peeks into the fabulous schedule of events we were well aware that the Centennial Committee, New York Host Section and AIME staff' had pulled out all the stops, laying on the best of everything, but the weather gimmick was the frosting on the cake. The Formal Greetings Session on the first morning, Joe Alford confided, was the greatest AIME experience of his life. Without doubt the honor bestowed on AIME by the greetings and felicitations of the presidents of the world's leading professional engineering societies was the greatest moment in AIME history-save one. That one exception was in 1928, when 1920 AIME President Herbert C. Hoover was elected President of the United States.

Jan 1, 1971

By J. M. Cases

Study of the normal interaction between flotation collectors and the silicates through measurement of the electrokinetic potential carried out by the streaming potential and flotation recovery methods indicates that the interaction is wholly 07 partly of electrostatic origin. In some cases, it partly consists of the chemical affinity of the polar head of the collector for the active surface sites. Reagents composed of a polar head and a paraffinic chain and forming micelles in solution were used as flotation collectors. They are sodium dodecylsulfate (anionic collector) and dode-cylammonium chloride (cationic collector). The adsorption isotherms on biotite of alkylamine chloride having 10 to 18 carbon atoms in their chain all show a sharp change in slope relevant to the condensation of alkylammonium ions into bidimensional phase.1-1 Condensation is possible because of the relative homogeneity of the adsorbing surface and of the very strong lateral binding forces through Van der Waals type bonds in the adsorption layer. The different isotherms are seen to coincide when, instead of the equilibrium concentration, the under-saturation ?µ = kT In C/C, is plotted in abscissa, C representing the concentration of the solution with which the adsorbed layer is in equilibrium and C, the saturation concentration of micelles in solution or. critical micellar concentration. More particularly, the undersaturation ?,u1*, corresponding to a surface coverage 6 of 0.5, is equal to Since silicates immersed in aqueous solutions show a surface charge which is a function of pH, it is of primary importance to study the influence of this parameter on the adsorption of collector ions acting as Strong electrolytes in the pH range where they are utilized. The aim of this present paper is to determine by studying electrokinetic phenomena and recovery curves effectuated with a cationic collector and a anionic collector, the nature of the normal adsorbate-adsorbent interaction. Tables 1 and 2 sum up part of the results previously obtained'H11 for the determination of the point of zero charge of the silicate studied by the streaming potential method. Throughout the remainder of this paper, the surface charge will be considered positive for all values of pH below the point

Jan 1, 1971

By H. F. Korman, M. C. C. Mow, P. K. Dai

INTRODUCTION Detonations of high explosives in soil and rock have been used frequently in civil engineering applications. Of particular interest in recent years has been the development of test methods to simulate the desired blast and shock environments for the testing of protective structures. The United States Air Force, in particular, the Air Force Weapons Laboratory, in conjunction with the Defense Atomic Support Agency, has in recent years, developed special technology for simulation testing of protective structures in soil and rock media. Such a technology, although initially developed for military applications, is rapidly finding its way into civil applications. One of the major problems in the design of the simulation test is the correct prediction of ground motion induced by the detonation of high explosives. This paper presents a useful prediction method which is developed specifically for ground motion in rock that is induced by the detonation of a buried planar array of explosive columns (See Figure 1). The technique of simulating shock environment using such an array is called the Direct Induced High Explosive Simulation Tech- nique (DIHEST). Normally, each shot hole may contain canisters of ammonium nitrate positioned at various depths, or a slurry explosive with detonators positioned along its length (See Figure 1). The depth and width of the array, the spacing of shot holes, the spacing of detonators, the degree of containment, and the charge weight are the variables which govern the induced ground motion

Jan 1, 1971

By John M. Logan, John Handin

Quasi-dynamic triaxial compression tests have been done for the first time at confining pressures to 7 kb. The intermediate strain-rate apparatus employs a gas loading cylinder which allows axial strain rates up to 102/sec on a sample 2 cm in diameter and 4 cm long. Samples can be deformed at confining pressures to 7 kb. Strain gages bonded to the loading piston and to the jacketed specimen allow internal measurements of load and sample strains respectively. Westerly granite has been deformed at confining pressures to 7 kb, room temperature, and axial strain rates of 10-2 to 1/sec. An increase of ultimate strength with confining pressure was found as expected. The ultimate strength was also found to vary directly with increasing strain rate; the rate of rise increases with confining pressure. Brittle deformation has dominated the sample behavior. Solenhofen limestone has been deformed at confining pressures to 3 kb, room temperature, and axial strain rates of 10- to 10/sec. The brittle-ductile transition was found to take place at about 1.5 kb confining pressure at a strain rate of 10/sec.

Jan 1, 1971

By A. H. Tousley

The cement industry is on the horns of an economic dilemma. Within the last ten years, its over- capacity in the United States has varied from 139- 127% of demand (Fig. 1). The most direct effect of this is seen in cement prices, which reached a peak in 1960, retreated steadily through 1966 and only recently climbed back to the 1960 level again. With prices in a slump and production costs estimated to be up almost 30%, there has been a steady drain on cement profits. Since 1960, labor costs have increased 86% while fuel costs have risen 18%. Meanwhile, customer service costs have also soared owing to the competition for cement customers and the wider variety of available cement products. This search for sales advantage has in turn led to a higher Blaine number, which means more grinding and hence bigger mills, more power, and, once again, higher costs. New plants as well as expansions and revisions to existing plants are also costing more owing to higher

Jan 1, 1971

By David A. Sterling, Roger C. Malan

The Atomic Energy Commission is investigating the distribution of uranium and thorium in the Precambrian of the western United States and the relationship of time-space-facies patterns of uranium and thorium enrichment in the Precambrian, to the major resources of umanium in Mesozoic and Cenozoic continental clastic sediments. The results of preliminary studies in the southwestern. United States are summarized. Approximately 50% of the uranium resource of the Free World is in deposits of Precambrian age, principally in lower Proterozoic conglomerates in Canada and South Africa (Uranium Resources, Joint Report, ENEA and IAEA, 1967). Most of the uranium resource of the United States is in Mesozoic and Cenozoic continental clastic sedimentary rocks that fill intracratonic basins. The Atomic Energy Commission (AEC) is investigating the distribution of uranium and thorium in the Precambrian of the western United States and the relationship of time-space-facies patterns of uranium and thorium enrichment in the Precambrian to the major resources of uranium in the Mesozoic and Ce-nozoic host sedimentary rocks. This paper summarizes the results of preliminary studies of the Precambrian in the southwestern United States including New Mexico, Arizona, southern Nevada, and southern California (Fig. 1). The host rock provenances for the major uranium resources in epigenetic deposits of Mesozoic and Ce-nozoic age in the western United States were in areas of extensive Precambrian exposure along the eastern margin of the Phanerozoic geosynclinal belt (Fig. 2). Mesozoic continental clastic sediments in the Colorado Plateau contain about two-thirds of the uranium resource of the United States. These sediments formed from detritus derived from the Mogollon highland in the southwestern United States where the Precambrian was extensively exposed1-1 (Fig. 2). A genetic relationship may exist between this provenance and the major uranium deposits of the Colorado Plateau. The Pre- cambrian might be equally important in the genesis of uranium deposits whether the most important process in the formation of these deposits was the leaching of low-order intrinsic amounts of uranium from Precam-brian granite or from Mesozoic pyroclastics derived from syntexis of the Precambrian basement rocks.' Precambrian Geochronology of the Southwestern United States The Precambrian geochronology of the southwestern United States is in an early stage of systematic study. Until recently, the only basis of correlation was through inconclusive field relationships. However, with the increased use of isotopic age dating, new data are becoming available for correlating regional and local events. As yet, there is no undisputed evidence of ages greater than 1.8 billion years (by) old in the southwestern United States. However, most geologists who have studied the region agree that volcanism and marine sedimentation of predominately eugeosynclinal facies took place in a northeasterly trending geosyn-cline prior to 1.7 by."' Because of insufficient evidence for a pregeosynclinal continental crust, some researchers believe the geosyncline may have developed on oceanic crust.' However, sediments metamorphosed to 1.7 by-old felsic paragneisses in the Panamint Range, California," and southeastward into southern Nevada are believed to have had a nearby continental provenance. The three Precambrian disturbances that are recognized in the southwestern United States are 1.6 to 1.8 by, about 1.4 by, and about 1.1 by-old (Fig. 3). In addition to plutonism, these disturbances are characterized by predominately lower-grade metamorphism. In this report, lower-grade metamorphic rocks include argillite, phyllite, slate, mica schist, and gneiss with relic sedimentary textures. Higher-grade metamorphic rocks, in this report, are recrystallized beyond megascopic recognition of the original rock type. Principal

Jan 1, 1971

By Roshan B. Bhappu, Raul A. Deju

A method is proposed by which the chemical reactions between water and a silicate bed can be related to equations of flow. First the reaction mechanism is studied both theoretically and experimentally. Once the reaction mechanism is established, the equations of flow are solved, and a solution (under physically reasonable side conditions) is obtained. Experiments to substantiate the solution are also presented. The knowledge of surface reactions at the water-solid interface is of critical importance in extractive metallurgy. This is especially true in regard to the froth-flotation process of mineral concentration and all phases of hydro metallurgical recovery of metals. Similarly, the problem of ground-water contamination is one of growing concern, not only because of the increasing demands on our sources of supply but also because of the increasing necessity to find vehicles of waste disposal. The hydrochemistry of waste waters must be understood to exploit and develop such resources properly. To understand these problems, it is necessary to obtain a better insight into the reactions that take place between water and a solid packed bed. To do this, we will develop here in a theoretical model that predicts the fate of a chemical species in solution as it reacts with a silicate bed through which the liquid percolates. The treatment will be one-dimensional in nature and will not include dispersion. Experiments will also be presented to substantiate the theoretical model, using the silicate minerals listed in Table 1. This paper is preliminary in nature and is part of a larger study of the surface chemistry of the silicate-water interface. Mechanism of Surface Reactions In a previous paper,' the authors discussed the properties of various silicate minerals from a mineralogical standpoint. Now efforts will be made to study the reactions that occur when these minerals are put in contact with water. The reactions occur almost entirely in the surface layer of the mineralsa and are termed sorp-tion reactions. In this study sorption denotes the composite of all physical adsorption and chemical adsorption occurring between the silicate surface and the water in contact with it. A model of sorption as seen from a chemical-bond standpoint is presented below. On the basis of this model, the surface reactions between deionized water and a silicate mineral can be studied. Sorption Model: It is known that as the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, the oxygen-to-metal bonding increases. Upon the fracturing of a silicate-mineral crystal, the oxygen-metal bond breaks more easily than the stronger oxygen-silicon bond, resulting in a negatively charged surface. Then, if the mineral is immersed in a liquid containing hydrogen ions, the negatively charged surface should tend to be neutralized by hydrogen ions from solution, resulting in a change of the solution pH. Thus, an increase in the degree of sorption of hydrogen ions must occur as the oxygen-silicon ratio in the crystal structure increases. Also in a previous paper,' the authors found that for a given silicate mineral the change of pH with time is given by

Jan 1, 1971

By Eric S. Cheney

The often-heard question "How can we interest young geologists and engineers in AIME?" is virtually the same as "How can we interest young geologists and engineers in the glamorous mining industry?" Many persons would reply that AIME and industry should improve their image by various devices aimed at high school students and teachers, boy scouts, and even grade school children. For more immediate results, I suggest that we concentrate our efforts at the professional level on students already identified as geol¬ogists and engineers. Why does our glamorous profession appear distinctly unglamorous to most of the engineers and geologists currently in college and graduate school? The answers seem quite simple to me. First, the profession talks almost exclusively to itself, seldom to the engineering or geologic public, and almost never to the lay public. Second, the industry has been overly conservative in all aspects of recruiting during an especially competitive and affluent period. Consequently, mining has taken a terrific public drubbing from preservationists who still portray its leaders as robber barons. SME and AIME have, of course, various commendable programs for enticing student interest, including student membership, the low dues for this membership, the somewhat reduced prices at which students can attend AIME meetings and buy AIME volumes, and the large number of AIME Student chapters on campuses. Obviously, more active encouragements are needed.

Jan 1, 1971

By D. A. Elgillani, M. C. Fuerstenau, J. D. Miller

Adsorption of lead and ferric iron on quartz and alumina is presented as a function of pH. Only the hydrolyzed species of these metal ions, FeOH++ and PbOH+, adsorb significantly on each of these minerals. Zeta potentials of quartz were measured as a function of pH in the presence of various additions of aluminum, lead, and magnesium salts. Sign reversal occurs at the pH values where significant concentrations of hydroxy complexes are formed. Models of adsorption are presented in the absence and presence of collector. The mechanism of adsorption of metal and collector species in the activation of nonmetallic minerals is still the center of considerable discussion in spite of the extensive study given this system. Until recently, the view was widely held that hydrated metal ions were responsible for this phenomenon. This fact is surprising, since it had been shown that the pH range in which flotation is effected corresponds to that in which metal ion hydrolysis occurs.' Additional support of this concept was pro vided by the work of Wolstenholme and Schulman in another system.' Later work has shown that hydroxy complexes of metal ions are the active species. These studies have also indicated that basic aqueous complexes of metal-collector may be necessary for flotation.3-7 Depending on the molecular weight of the collector, formation of these complexes may occur before or after precipitation of the metal-collector salt has occurred. Ion pair formation can occur when low molecular weight collectors are involved because relatively high concentrations of metal hydroxy complex and collector can be present in solution before precipitation occurs. This is not the case when high molecular weight collectors are used. A model of aqueous complex adsorption has been presented6,7 in which it has been assumed that adsorption occurs by the formation of water from adsorbed hydroxyl and hydrogen of the hydroxyl contained in the complex. Other authors8 have suggested that hy-droxy complexes are involved in these systems but that collector adsorption occurs by replacement of the hydroxyl of the adsorbed metal hydroxy complex with a fatty acid anion. All of these investigations have involved mineral surfaces that were negatively charged so that it is not possible to state with certainty whether hydrated metal ions or hydroxy complexes are the active species in this system. Use of a positively charged mineral should be helpful, however, since the hydrated metal ion will be repelled from this surface. On the other hand, if the hydroxy complex adsorbs by splitting out water, surface charge should have no effect because of the free energy decrease that the system will experience when water is formed. In this regard, sapphire is well-suited for study, since its surface is positively charged until approximately pH 9. Electrokinetic studies of quartz in the presence of various metal ions should also be useful in establishing the mechanisms of adsorption in these systems. That is, if the hydroxy complexes adsorb by water formation, drastic changes in the zeta potential should occur in the pH range in which hydrolysis occurs. In this view, adsorption of ions of widely different hydrolysis characteristics on both sapphire and quartz was measured. In addition, zeta potentials of quartz were measured as a function of pH in the presence of various metal ions and compared with flotation responses obtained under similar conditions. Experimental Materials and Techniques Reagent-grade aluminum, ferric and magnesium chlorides, and lead nitrate were used in this investigation. Adjustments in pH were made with reagent-grade HCl or KOH. Conductivity water, made by passing distilled water through an ion exchange column, was used in all of the experiments.

Jan 1, 1971

By C. W. Schultz, R. B. Tippin

Statistical screening is so named because a particulate feed is separated into "size" intervals on the basis of the probabalistic behavior of the individual particles (i.e., their probability of passing the screen) rather than by physical restraint. To illustrate this statement, consider a conventional screening operation. A particle which is larger than the openings in the screen cloth is physically restrained from passing through and is repeatedly reflected from the surface until it is discharged as oversize. Of those particles smaller than the screen openings, the very smallest tend to pass the screen near the feed end while those nearer in size to the screen opening tend to pass at a greater distance from the feed end. Alternatively, we could say that the particles with high probability of passing through the screen are concentrated near the feed end while particles of low probability of passing are dispersed from the feed end. This tendency to segregate is the basis for size separation by statistical screening. The purpose of this note is to: 1) Show that the distribution of material passing an array of screens can be described by a modified binomial distribution. 2) Demonstrate that an efficient size separation can be made by this technique. 3) Relate some of the more important screening parameters to the efficiency of the size separation. The Distribution Function The distribution of undersize products along the length of a screen can be derived with the help of a few simple definitions and assumptions. 1) First, we must assume that each particle has some probability of passing a screen on a single presentation. Further, we must assume that this probability is constant and is not affected by the position of the particle on the screen. It must also be acknowledged that several factors enter into this probability. Among them are the "action" of the screen, the slope of the deck, the shape of the openings, etc. The relationship between these factors, however. is not the subject of this paper. 2) To simplify calculations, all particles falling within a size range on the Tyler scale, e.g., —x + x/ mm, are assumed to have the same probability. 3) It is assumed that particles which do not pass the screen on a presentation are reflected a unit distance forward, i.e., the direction of material travel. A unit distance is defined as the distance between the centers of consecutive wires in the screen cloth.

Jan 1, 1971

Striving to do a better job of ad- ministering the letter and spirit of the Federal Coal Mine Health and Safety Act of 1969, the Interior Department recently invited criticism-and got it. The criticisms were voiced on July 1 and 2 at the first of a series of public meetings being held by the Office of Hearings and Appeals at the Department's behest. Later meetings, at which all interested parties are invited to comment, are to be announced in the press and the Federal Register. Persons wishing to participate in the meetings should contact the Director, Office of Hearings and Appeals, 1015 Wilson Blvd., Arlington, Va. 22203. At the first Hearing, USBM Director Elburt F. Osborn outlined the progress his agency has made to date in implementing the law on three fronts: enforcement, education and research. Since the Health and Safety Act became law on December 30. 1969, he said, the Bureau's force of inspectors has grown from a mere 300 to almost 1100, while mine inspections have increased from 10,265 in 1970 to 11,021 for the first six months of 1971. On the educational front. Osborn said, the Bureau now has some 60 instructors who have trained about 50,000 miners in safety procedures since March 30. 1971. Classes at the new Federal Mine Safety Academy for both government and industry personnel begin on September 1, 1971. he added. Health and safety re- search, meanwhile, has been allot- ted $20.1 million for the 1971 Fiscal Year. Of this, $8.1 million is assigned to the Bureau and $12.3 million to contracts with universities and private companies. Admittedly, Osborn said, the mine fatality rate is still unacceptable, hut it was lower in the first half of 1971 than ever before---0.73 per million man hours and 0.31 per million tons of coal.

Jan 1, 1971

By S. C. Sun, John A. L. Campbell

Objective of the ittvestigation was to determine the electrokinetic differences, if ally, of anthracite lithotypes and thus establish the feasibility of making a coqlstituent separation by froth flotation or other surface-dependent processes. The elec-trokinetic properties were determined by streaming potential methods. In addition, chemical and physical analyses of the lithotypes were made to establish nonsubjec-tive parameters for their diflerentiation. Electrokinetic results indicate a difference in the characteristics of the lithotypes. The isoelectric points of 4 anthracites and 12 lithotypes were obtained. It was suggested that the relative flotation rates of the lithotypes were pH dependent and that the maximum flotation rate of anthracite occurs in an acidic circuit. Although there has been an increased interest in the electrokinetic properties of coal,' research on the subject is still in an early stage of development."' To the authors' knowledge, no electrokinetic studies have been made on coal lithotypes, particularly anthracite litho-types. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods. It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface-dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published.? The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results; however, the result? are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation. Experimental Procedure Prior to discussing the experimental work per se, it would be of value to establish an understanding of anthracite lithology. Anthracite Lithology: Coal seams display two different modes of variation, rank and type. A coal's position in the continuous series ranging from peats through anthracites determines its rank. The rank of the material under consideration is anthracite. The different bands of coal which constitute a coal seam are distinctly contrasted in regard to physical properties and chemical composition. These megascopic bands are the coal types and are termed lithotypes., A megascopic examination of 11 anthracites revealed three distinct, homogeneous, lithotypes. The classic description of bituminous coal lithotypes as proposed by Stope" was found to be quite adequate for recognizing the three lithotypes in anthracite, namely vitrain, durain, and fusain. The term vitrain describes the brilliant constituent of coal; durain describes dull coal; and fusain is the term applied to fossil charcoal. The anthracites studied were generally found to contain 60-80% vitrain, 10-30% durain, and 1-10% fusain. A complete description of the physical characteristics and chemical composition of the studied lithotypes can be found in a previous publication.' Sample Preparation: Nine of the anthracites used in the investigation were from Pennsylvania, one was from Russia, and one from Wales. Table 1 shows the various designations and sources of the employed anthracites. The letter V, D, or F added to the whole coal designation indicates respectively the vitrain, durain or fusain lithotype of that coal. The samples were carefully collected to avoid contamination. To insure against oxidation, the samples were obtained as fresh as possible and stored under nitrogen or water. Generally a representative sample of the seam and samples containing high concentrations of one or another of the petrographic constituents were secured for each coal. Pure lithotypes were prepared by manual separation and selection. The pure lithotypes and representative samples were ground to —35 mesh and screened to 35 x 48 mesh. The 35 x 48-mesh fraction was then passed over a magnet to remove iron contamination, washed with doubly

Jan 1, 1971

By T. lkeda, R. S. Montgomery. A. Hara

Actual test specimens used in the previous laboratory wear investigation,' were fully characterized and the data is given in Table 1. Most of the carbides tested could be placed into groups of similar mean grain size. When the wear rates of the members of these groups were plotted as functions of their hardnesses, a family of curves resulted; curves for groups containing data from larger grained composites were at lower wear rates at the same hardnesses. Most specimens tested showed only A-1 porosity (ASTM Standard designa-

Jan 1, 1971

By Roy W. Wright

Introduction The title of my paper is satisfyingly broad and allows me to touch lightly or dwell at length on virtually any aspect of mining, while endeavouring not to trespass on the subjects of other papers to be presented. However, at this stage in our world history when for the first time we are beginning to take conservation and the welfare of future generations more seriously, I want to concentrate mainly on the question of whether or not there will be the resources of minerals available to sustain mankind's progress in the generations ahead. Metals and the Population Problem The supply of raw materials is of course only one of the fundamental problems that will face future generations: if we assumed that the world population would continue to increase at the present explosive rate, then I believe we can say with certainty that other fundamental problems of much greater significance would arise long before a shortage of raw materials - or other substitutes -had any impact on the progress of mankind. Thus, I must start this paper with the assumption that some equilibrium in population will be arrived at before these other problems overwhelm the world. Will the Metals Run Out? At the 75th Anniversary Meeting of this Institute in March, 1947, Clinton H. Crane, President of St. Joseph Lead Co., prophesied that for the next 100 years there would be enough copper, lead and zinc for every essential need. He defined a need as essential where the qualities of the metal in that use were irreplaceable. Today, except for one or two cases such as lead in lead-acid batteries, few metals have qualities that cannot be provided either by another metal or by another material. It is more a question of what the engineer or manufacturer is prepared to pay for special qualities as compared with using cheaper materials and perhaps a less satisfactory design.

Jan 1, 1971

By C. Fairhurst, B. C. Haimson

Pink Tennessee Marble was tested for wedge bit penetration characteristics at static and dynamic (10 - 250 ft/sec) loading rates. No significant differences were found within the dynamic range as far as the energy required to remove a unit crater volume and the force used to cause a certain penetration. Under static loading, however, both the energy and the force required were significantly lower. Tests run on bits of varying width indicated that as the wedge bit narrowed to an almost conical shape, the energy used per unit crater volume became considerably lower.

Jan 1, 1971