Search Documents

By Fredrick C. Kruger

Introduction This surprisingly little-known group of minerals, the nonmetallics, so-called for their lack of metallic luster, is the largest group of the mineral kingdom, and cinstitutes perhaps 75 percent of all mineral species. For the most part, these minerals are compounds of the common acids, oxides, hydroxides, and two elements, carbon and sulfur. The list of the non- metallic minerals, therefore, is very long. It includes the borates, carbonates, chlorides, fluorides, nitrates, phosphates, silicates, sulfates, and less commonly, arsenates, chromates, molybdates, suliides, tungstates, and vanadates, the latter groups, and many of the oxides, being sought principally for their metal content. Those nonmetallics used commercially are generally called the industrial minerals, although in addition this term also includes a considerable group of rocks. The list of industrial minerals and rocks is continually growing as new uses are found, and it now numbers over 300 commodities. The industrial minerals industry has developed since about 1920. There- fore, the development has been fast, and it has been more or less parallel with the development of the art of minerals beneficiation. General Discussion of the Group This group is so heterogeneous that it has defied logical, or widely accepted, classification, whether by origin, composition, or end use, and perhaps for this reason the industrial minerals generally have received short shrift in both teaching and research. Except for those involved with asbestos, cement, fertilizers, gypsum, salt, sand and gravel, few large companies have deigned to enter the field, and consequently most industrial minerals have been developed for the most part by the small operators or entrepreneurs. Yet surprisingly, except for one war year, the nonmetallics have always surpassed the metals in value and tonnage (Fig. 1). One main characteristic that most of the nonmetallics have in common is direct sensitivity to labor and transportation. In other words they are characterized by large bulk and low-unit value, and hence have what might be termed a "place value".

Jan 1, 1971

By Thomas V. Falkie, Robert Stefanko

Recently The Wall Street Journal featured a series of articles titled "The Dirty Work-Brutal, Mindless Labor Remains a Daily Reality for Millions in The US.-Mining Coal, Shoveling Slag, Gutting Hogs Pays Bills But Can Drain Spirit, Hope." The article was devoted to describing how tough and dangerous is mining (and some other jobs) and how rough life is for miners and their families. Similarly during the past few years some psychiatrists and sociologists have devoted increased attention to the attitudes and life styles of miners. Unfortunately most of their approaches have been neither scientific nor objective, and very little good clinical research has been done on the subject.

Jan 1, 1971

By Clint L. Milliken

The smelter is often considered the flywheel of the copper industry. No other unit can produce such a uniform product from so many starting materials. Direct-smelting ore, concentrate, precipitate, refinery slag, and scrap in almost any combination can be processed into blister or anode copper. Copper smelting practice has advanced little in the last century. It is still basically matte smelting, although the source of matte has changed from the blast furnace to the reverberatory furnace because of changes in smelter feed, and the Great Falls converter has been replaced by the Peirce-Smith converter. This lack of progress has continued because the economic forces required to produce change have not been of sufficient magnitude. Traditionally, the smelting, operation has required only about 10% of the total cost of producing copper from its ores and this minor cost item has not warranted change until recently.

Jan 1, 1971

By C. W. Robinson

Transportation is the minerals business. Once upon a time the geologist, the engineer and later the metallurgist reigned supreme, but the leading role in mineral development today is the economist-especially the transportation economist. Obviously this trend is more important for large volume, low value mine-to-market movements of such commodities as iron ore, phosphate, potash, coal and petroleum. But, transportation is of sufficient importance to all mining activities to be included in forward planning. Civilization has been influenced by transportation developments to an extent little understood or appreciated. Although industrialists are capable of intelligent historical analysis of this phenomenon, too frequently they have failed to project, or anticipate those changes in transportation techniques which will influence the pattern of industrial growth.

Jan 1, 1971

By William N. Poundstone

To forecast the future of coal intelligently, one must first consider the market outlook. Coal can be used for many purposes, but currently about 25% of it goes into metallurgical coke, while 75% serves as fuel. Coal for metallurgical coke should show a modest growth for at least the next decade, primarily because of increased exports, but the important factor in the coal outlook is energy. Today, this country faces a serious shortage of energy, and its requirements are growing at an almost unbelievable rate. Last year the United States consumed 68 quadrillion Btu, or double the energy it consumed in 1950, and, if projections are correct, this figure will grow to 150 quadrillion Btu by 1990. Thus, in one working lifetime, the nation's energy consumption is expected to increase by roughly five times. The future of coal hinges on its degree of participation in meeting this energy need. The Federal Power Commission predicts that coal consumed by electric utilities will increase about 4-576 per yr, reaching 472 million tons by 1980 and 615 million tons by 1990. If this projection proves correct, 1980 consumption will be double that of last year and, even more startling, the utility industry alone will use more coal in 1990 than the entire coal industry produced in 1970. This is a tremendous increase, but in view of the projected energy growth, it is difficult to see how this country's needs can be satisfied with- out a coal contribution of this magnitude. Unless some new source such as solar energy is discovered, it must be assumed that the projected energy will come principally from the present-day sources-oil, gas, nuclear materials and coal.

Jan 1, 1971

By W. W. Anderson, D. G. Girton

The photoluminescence of Pr, Nd, Ho, Er, Tm, and Yb in CdS, and Ho, Er, Tm, and Yb in ZnSe has been observed from crystals Prepared by diffusion using rare earth metals and an excess chalcogen pressure. For a given temperature, time, and chalcogen pressure the spectral characteristics were very reproducible from run to run, and the emission intensity for Nd, Er, and Yb in CdS was as high or higher than the best vapor phase doped crystals we have grown. For a few rare earths it was found that certain conditions of diffusion tend to yield optimum rare earth emission intensity with respect to the background lattice emission. Photoluminescence measwements of Yb in CdS as a function of depth gave a profile which was neither a Gaussian nor complementary error function. Part of the profile appears to arise from a fast component of the diffusion and the other part from a slow diffusing component. At 960°C and 33 atm S pressure, a com -plimentary error function approximation of the slow diffusing component gave a diffusion coefficient of D = 1.3 x 10-9 sq cm per sec. MOST of the studies of emission from rare earth ions in II-VI compounds have been reported on crystals doped during growth,1,2 although Kingsley and Aven prepared ZnSe:Er by diffusion for paramagnetic resonance and fluorescence studies. Pappalardo and Dietz prepared CdS:Yb by diffusion, but they made optical absorption measurements., We know of no study on the properties of rare earth diffusion in the II-VI compounds. To date we have diffused Pr, Nd, Ho, Er, Tm, and Yb into CdS, and Ho, Er, Tm, and Yb into ZnSe and observed the rare earth emission spectra. For a given temperature and chalcogen pressure, the emission characteristics are very reproducible from run to run and for Yb, Nd, and Er in CdS, as good as the best crystals we had prepared by doping during vapor phase growth.2 The emission of Pr, Ho, and Tm has been observed in CdS prepared by diffusion for the first time. Previous attempts2 to prepare these later three materials by vapor phase growth were unsuccessful. The problem of obtaining reproducible characteristics in II-VI semiconductor compound work is well known.5 Not only is it difficult to reproduce results from one laboratory to another but it is sometimes difficult to reproduce results from one growth run to another under ostensibly identical conditions within one laboratory. This situation has been particularly bothersome in research on the luminescence of rare earth activated ZnS1 and Cds2. Crystals from one vapor phase growth run would show very strong rare earth line emission while crystals from a nearly identical run would show no rare earth emission. It was also observed on occasion that the intensity of the rare earth emission was not constant over the entire volume of a single crystal. MATERIAL PREPARATION AND INSTRUMENTATION Vapor phase grown boules of CdS were supplied by Dow Corning. This material was characterized by a free electron concentration of n - 3.5 x 1015 cm-3 and Hall mobility of 350 sq cm per v sec at room temperature. There were microscopic voids and decorated precipitates in some samples. The precipitates annealed out at diffusion temperatures but the voids remained. Single crystal rectangular samples of mm dimensions were sawed from the boules. The ZnSe was polycrystalline, UHP grade from Eagle-Picher. Poly-crystalline samples were sawed from the ingots. The samples were lapped, polished on one side, etched in a solution of 0.5 M K2Cr2O7 in 16 N H2SO4, and thoroughly washed in distilled water. A sample, excess sulfur (or selenium), and 5 mg of rare earth metal (turnings) were sealed in a 3.6 cm3 quartz ampoule at about 2 X 10-5 torr. The high chalcogen pressure used (1 to 30 atm) prevented thermal etching of the crystals and affected the diffusivity and solubility of the rare earth ions in the crystal lattice. For meaningful or reproducible results, it is thus necessary to specify the vapor pressure at which the diffusion was carried out. It is assumed that a negligible amount of the chalcogen was used in the formation of rare earth sulfides or selenides Our sulfur vapor pressure calculations are based on data assuming S2, S6, and S, molecules only in which case the equilibrium constants are given by6 where the pressures are expressed in torr. Selenium vapor consists of a mixture of Se2, Se4, Se6, and Se6 molecules. The selenium vapor pressure was calculated using equilibrium constants given by The status of the rare earth source during diffusion is unknown, i.e., the partial pressures of the rare earth metal and of the rare earth chalcogenides has not been determined. All emission spectra were recorded at 77°K on a Perkin-Elmer model 98-G spectrometer using a 640 line per mm grating. No correction was made for the spectrometer and detector spectral sensitivity. Excitation was by means of an XBO 1600 w xenon arc

Jan 1, 1970

Jan 1, 1970

By R. L. Caldwell, E. E. Glenn, L. J. Norton, A. J. D. Straus, S. V. Holcomb, J. Zemanek

A new and unique logging tool, called the Borehole Televiewer (BHTV), has been developed to inspect boreholes and to evaluate formations. Even though geologists and engineers have had only about 3 years' experience with the BHTV, the thinking of many of them has been radically influenced by the fascinating and revealing "log-picture" recorded with the tool. The BHTV fills a need for a logging tool that can produce a direct and descriptive record of the physical properties of the borehole environment. Although primarily developed to evaluate fractured reservoirs, the BHTV has been used successfully to solve a variety of problems related to formation evaluation and borehole inspection. Geologists and petroleum engineers have been confounded for many years by the problems of locating and evaluating fractures. Interpretation of the usual resistivity, acoustic or radioactivity logs, as well as the analysis of cores, for evaluation of fractured reservoirs is extremely difficult and often not definitive. This is understandable since analysis of cores from fractured formations has reported variously: (a) low porosity, (b) no effective permeability, (c) lack of any matrix oil saturation and (d) oil stains on fracture planes as the only indications of potential production.14 In recent years acoustic amplitude logs have been introduced and used with varying degrees of success to locate fractures.8'9'11"13 Conventional amplitude logs at best give only qualitative answers where quantitative ones are desired. The logs reveal nothing of the orientation of the fractures. In addition to these logs, various types of cameras, television, and rubber impression packers have been used for borehole inspection. (See Appendix.) The BHTV logging tool supplies both the quantitative and the orientation answers about fractures. The borehole can be filled with any homogeneous, gas-free liquid such as fresh water, saturated brine, crude oil or drilling muds. This tool takes an "acoustic picture" of the borehole wall. The resulting log is a representation of the borehole wall as if it were split vertically and laid flat. The log is oriented with respect to magnetic north. Any physical changes in the borehole wall are seen as changes in picture intensity. In this way, fractures, deformation or pits are reflected on the log. Tool Description The fundamental parts of the BHTV are shown in Fig. 1. A piezoelectric transducer probes the borehole wall with bursts of acoustic energy. A flux-gate magnetometer senses the earth's magnetic field and provides the means for determining the orientation of the log. A motor rotates the transducer and mag-

Jan 1, 1970

By R. L. Vaughn, H. R. Cooper

Effective procedures for automating X-ray assaying by use of a computer are described. These methods have advanced the reliability and accuracy of X-ray data, resulting in improved assay measurements for operations and process control. Assaying by X-ray fluorescence has been increasingly used in the mining industry, both for analyzing solid H.R. COOPER and R.L. VAUGHN, Members AIME, are Systems Manager-Process Control and Senior Systems Analyst, respectively, Scientific & Engineering Computer Center, Ken-necott Copper Corp., Salt Lake City, Utah. TP 68B236. Manuscript, Sept. 16, 1968. Discussion of this paper, submitted in duplicate prior to Dec. 15, 1969, will appear in SME Transactions, March 1970, and AIME Transactions, 1970, Vol. 247. samples for smelter, mill, and mine quality control and for continuous stream analysis of mill pulps. The important advantages of X-ray methods in laboratory assaying are reduced analysis cost, and for on-stream analysis, immediate assay information on concentrator streams. Of the numerous reports concerning X-ray analysis in mining operations, one is referenced which can be noted particularly in conjunction with this report.' Continuous X-ray analyzers have been installed at Kennecott and other mining companies for operations guidance and trend information for a number of years. However, complete operational acceptance of X-ray data has been slow, due* to the difficulty in maintaining

Jan 1, 1970

By Abderrafih Guessous

INTRODUCTION Morocco is an important lead-zinc producing country: 120,000 tons of lead concentrates were produced in 1968. Zinc ore production is less, 67,000 tons of concentrates in 1968. Most of the present production comes from three districts (fig.1) (i) Touissit-Bou Beker district, in the eastern part of the country, close to the border with Algeria. (ii) Aouli-Mibladen district, in the central part of the country. (iii) Aouam district, about $0 miles south of Meknes. In the first district lead and zinc are always found together. The two other districts produce mainly lead. This paper will be limited to a short description of geology and mining methods in the three aforementioned districts. More detailed geological informations can be found in the symposium on lead-zinc deposits in Africa (1).

Jan 1, 1970

By J. H. Swisher

Two recent papers in this journal1,2 contain experimental evidence for an anomaly in the concentration gradient for tracer diffusion. In both papers, the authors suggest that this anomaly is due to a Gibbs' absorption effect. Their hypothesis is that surface active tracer elements tend to remain in or near the surface adsorption layer, thereby altering the diffusion flux and concentration gradient. It is not clear how the anomaly can be explained in terms of an adsorption effect. Surface tension forces act parallel rather than perpendicular to a surface and therefore should affect only the rate of spreading of surface active agents tangentially across a surface. Frenkel3 has given a short treatment of surface tension as a driving force for surface diffusion. While the equilibrium concentration of a surface active agent at the surface of a solution is known to be higher than in the bulk, its chemical potential is necessarily the same. It is difficult to see how adsorption can result in an anomaly in the chemical potential gradient, which is the driving force for diffusion. A more detailed explanation by the authors of the adsorption mechanism is in order. A similar anomaly does not seem to arise where

Jan 1, 1970

By R. R. Vandervoort

The creep behavior of Nb(Cb), Ta, Mo, and W was determined under conditions of constant atomic dif-fzisivity, constant stress to elastic modulus ratio, and nearly equivalent grain size, and the steady-state creep rates obtained from these tests were correlated with calculated stacking fault energies for the metals. These results, in conjunction with similar data for several fccMetals,13 suggest that stacking fault energy may influence the creep strength ofbcc metals. The interrelationship between steady-state creep rate, subgrain size, and stacking fault energy was examined. It was found that the subgrain size for a given creep stress, increased as stacking fault energy increased, but that this relationship did not cormpletely account for the effect of stacking fault energy on creep rate. The crystallography and energetics of stacking fault formation in bcc metals has been discussed by a num-ber of authors,1-5 and impurity stabilized stacking faults on (112) planes have been observed in Nb,6,7 w,8,9 Fe,] and V" by transmission electron microscopy. However, a crucial question is whether or not stack-ing faults influence the mechanical strength of bcc metals. Potentially, stacking faults could increase strength by reducing the mobility of the partial dis-locations bounding the fault, by acting as barriers to slip dislocations, and by retarding the climb of dislo-cations during high-temperature deformation. The objective of this study was to seek a correlation be-tween creep strength and stacking fault energy for several bcc metals; namely, Nb, Ta, Mo, and W. The creep behavior of most polycrystalline metals and alloys at high temperatures and moderate stresses can be described by the following relation:11,12 im=Af(s) where i, = minimum creep rate, A = constant, j(s) = a function involving metallurgical structure, a = applied stress, E = average elastic modulus at the test tempera-ture, w = constant (equal to 5 for most pure metals), D = diffusion coefficient. One factor in the structure function F(s) which sig- R. R. VANDERVOORT, Member AlME is Research Metallurgist, Process and Materials Development Division, Chemistry Department, Lawrence Radiation Laboratory, University of California, Livermore, Calif. Manuscript submitted February 28, 1969. IMD nificantly affects the creep resistance of fcc metals is stacking fault energy, and creep rate has been shown to vary directly with stacking fault energy to the 3.5 power." In the latter investigation, four fcc metals of widely different stacking fault energies (Ag, Cu, Ni, and Al) were creep tested at a constant stress to modulus ratio of 1.21 x 10-4, at a constant diffusivity of 2.7 x 10-12 sq cm per sec, and at nearly equivalent grain sizes of about 0.7 mm. The creep data were then correlated with stacking fault energies. In the present study, a similar procedure was followed. All materials used in this work were consolidated by powder metallurgy techniques. Impurity contents in the as-received materials are listed in Table I. Chemical analyses showed that no measurable contamination of the test specimens occurred during pretest annealing treatments or creep testing. Specimens with a gage section 0.75 by 0.125 by 0.050 in. were creep tested in tension in a vacuum of less than 10-9 torr. Deformation at temperature was measured by tracking fiducial marks on the gage section of the specimen with an optical comparator. Optical deformation measurements also permitted observation of the macroscopic characteristics of the deformation Table I. Typical Specimen Impurity Content, ppm Nb Ta Mo W C 45 10 155 6 O 185 30 4 10 N 30 6 3 2 H 5 I 1 <1 als 3 10 2 15 Ca <5 I3 5 Cr 5 <3 10 <5 Cu 10 50 2 15 Fc 10 10 150 35 Ni 2 150 20 <5 Si <I0 1 3 <10 Ta 100 Ti 10 8 1 Zi 15 50 1 3 Table II. Test Conditions for Constant Stress-Modulus Ratio of 6 X 10.&apos; and Constant Diffusivity of 2.7 X 10-12 sq cm per see, and Grain Size Values for the Given Pretest Annealing Treatments Literature references Pretest Annealing for E and D Treatment Stress, Temperature, ___"&apos;Values__ Grain Tempera-Metal psi "C E D Size, mm ture, .C Time hr Nb 745 1525 14 15 to 17 0.83 1650 I Ta 1220 1770 18 19.20 O.91 1800 I Mo 1975 1630 18 21 0.77 2200 I W 2140 2265 18 22 040 2400 5

Jan 1, 1970

By G. B. Craig, H. E. Rosinger, W. J. Bratina

NUMEROUS studies have been reported on how the mechanical properties of a bcc metal are affected by interstitial solute atoms in the temperature range where appreciable diffusion occurs in finite time. Only recently, though, has work on an "interstitial-free" iron been reported, this by Leslie and sober,&apos; on an Fe-0.15 pct Ti alloy. The data was limited to a maximum temperature of 296°K. This work presents a systematic study of the flow stress and the activation volume of a similar material as a function of plastic deformation over the temperature range 253" to 473°K. The material studied was Ferrovac E iron containing 0.01 wt pct C and 0.0002 wt pct N annealed at 870°C for 1 hr, and the same iron with an addition of 0.15 wt pct Ti annealed at 870°C for 80 hr; cooling rates being 75°C per hr. In the latter alloy depletion of interstitials in the a-iron matrix associated with the second phase formation was expected. The temperature dependence of the flow stress was measured at 6 = 3.33 x 10-5 sec-1 from 253" to 473°K as a function of the deformation in 0.01 intervals from 0.03 to 0.12 strain. Results for two strains, 0.03 and 0.09 are shown in Fig. 1. The flow stress increased and reached a maximum in the Ferrovac E iron with increasing temperature, but showed a consistent gradual decrease in the Ferrovac E-0.15 pct Ti alloy. A yield point and Luders region, observed in Ferrovac E, was absent in the Ferrovac E-0.15 pct Ti alloy. Also, the Ferrovac E exhibited a serrated stress-strain behavior in the temperature range 330" to 400°K; dynamic strain-aging characteristics were absent for the titanium alloy. The activation volume was determined over the same temperature range by the method of stress relaxation at constant strain. Results are shown in Fig. 2. At the temperatures of serrated stress-strain behavior in Ferrovac E the activation volume was found to increase toward infinity and, as the temperature rose, to decrease, to about 100 to 200 v/b3. By contrast, the activation volume for the Ferrovac E-0.15 pct Ti alloy tended to increase continuously from the initial value of approximately 300 at 300°K to more than 800 at 473°K. Above 400°K, then, the corresponding activation volume values of Ferrovac E were less than that of the Ferrovac E-0.15 pct Ti alloy. The activation volumes, Fig. 2, appear to depend on dislocation-interstitial interaction in Ferrovac E and on dislocation-dislocation interaction in Ferrovac E-0.15 pct Ti alloy. The gradual increase in the latter metal is associated with thermally activated motion of dislocation segments.&apos; The decrease of the activation volume in Ferrovac E above 400°K is probably related to the diminishing effect of interstitials on dislocations. Here, the interstitials can be moved along with a dislocation without appreciable drag. As indicated in Fig. 1, removal of interstitials

Jan 1, 1970

By K. D. Sheffler, R. W. Hertzberg, R. W. Kraft

The Ni-Ni,Ti lamellar eutectic alloy responds to unidirectional solidification by alig-nment of the platelets of the two phases roilghly perpendicular to the moving solid-liquid interface. X-ray diffraction and zetallographic experimenls show that the following cryslallographic relationships exist in the directionally solidified ingots: lamellar interface w [0001] Ni3Ti 11 (111 }Ni local growth direction (1120) Ni3Ti n (110) Ni These relationships are rationalized on the basis of the crystallography of the constituent phases. In recent years researchers in several laboratories have shown that an aligned or "controlled" micro-structure can be produced in many binary eutectic alloys by forcing the alloy to solidify unidirectionally in an elongated crucible.&apos;-3 It also has been found that a unique crystallographic relationship often develops between the two phases in such a structure.4, 5 Since a parallel arrangement of phase particles in an alloy should, and, in many cases, does, produce unique and highly anisotropic properties, the alloys so produced are of potential interest in a variety of applications. Studies of these alloys are also of interest at the academic level because they help to improve our basic understanding of the way in which metals solidify. This paper reports the metallographic and crystallographic structure of another of these alloys—that between nickel and Ni3Ti. In a separate paper, hot tensile and stress rupture properties as well as deformation and fracture behavior of the same alloy are discussed.19 EXPERIMENTAL DETAILS AND RESULTS General Characteristics of the Eutectic Reaction. Several small exploratory Ni-Ti melts were made to resolve a conflict in Hansen6 over the eutectic composition. The alloy containing 16.4 at. pct Ti, Fig. 1, appeared metallographically to be closest to the eutectic composition, although small dendritic patches of proeutectic nickel are present. The eutectic morphology is lamellar and appears quite sharp and angular, indicating a strong influence of crystallographic factors upon the microstructure. Some of the eutectic nickel platelets are continuous with the primary phase, whereas in hyper eutectic melts a "halo" of nickel generally surrounded the proeutectic inter-metallic platelets, indicating that nickel is the nucleating phase in this eutectic reaction. Extensive precipitation of Ni3Ti has occurred in the primary nickel phase in a Widmanstatten pattern which makes the dendrites difficult to differentiate from the eutectic mixture. This phenomenon may account for discrepancies among the eutectic compositions reported in the literature. The sloping solvus line bounding the nickel primary solid solution explains the presence of the intermetallic precipitate. Poole and Hume-Rothery7 report that the solubility of titanium in nickel drops from 13.8 at. pct at the eutectic temperature (1304°C) to approximately 9 at. pct at 700°C (Ni3Ti, on the other hand, melts con-gruently and exhibits essentially no solubility for nickel or titanium). Lever rule calculations based upon Poole and Hume-Rothery&apos;s phase diagram indicate an increase from 21 vol pct Ni3Ti in the eutectic mixture at the eutectic temperature to 61 pct at room temperature. Selective point count measurements of the volume fraction of eutectic Ni3Ti platelets in the eutectic microstructure yielded a value of 46 i 2 vol pct, which required extensive precipitation of Ni3Ti from the nickel solid solution onto the eutectic intermetallic platelets during cooling from the solidification temperature. Influence of Directional Solidification. Nickel bar and titanium sponge of 99.9 pct purity were induction-melted in zirconia crucibles under argon in the proportion of 13.8 wt pct (16.4 at. pct) Ti to produce 14-lb master heats which were cast into investment molds yielding 5/8-in.-diam pins approximately 10 in. long. These pins were remelted under argon in horizontal zirconia boats and unidirectionally solidified to produce 1/2-in.-sq ingots approximately 44 in. long. Details of the experimental techniques and apparatus are described elsewhere.&apos;

Jan 1, 1970

By R. A. Wattenbarger, H. J. Ramey

The trend in gas well testing has been to rely more on the early-time flow data of drawdown and buildup tests than on stabilized flow tests. The stabilized testing methods often are not adequate for complicated modern gas reservoirs because many of these reservoirs have extremely low permeabilities and the transient flow period of a well test can last for days or weeks. It has become common to augment the flow capacity of gas wells by hydraulically fracturing their producing formations. In deep reservoirs the induced fractures are generally vertical and tend to follow a single plane of weakness. The presence of a vertical fracture at the wellbore complicates the transient flow behavior of a low permeability gas well. The flow is further complicated when turbulence occurs near the wellbore. Russell and Truittl published transient drawdown solutions for vertically-fractured liquid wells. They developed methods of drawdown and buildup testing utilizing these solutions, which were based on numerical simulation. Clark2 applied the basic Russell-Truitt solutions to analyze fractured water injection wells by falloff tests. Field examples were given to substantiate the method of analysis. The Russell-Truitt solutions and well testing methods can be extended to gas well flow. Millheim and Cichowicz3 presented the drawdown equations for *Now with Scientific Software Corp., Denver. ideal gas flow, including the effects of formation damage and turbulence. Two actual field cases were presented, both of which exhibited extensive fractures and turbulent flow. For the pressure range of these well tests, the use of ideal gas equations was acceptable. These field cases were significant in being the first published data showing the occurrence of turbulence in fractured gas wells. We, also, observed such cases in practice. Our purpose here is to extend the theory of fractured gas well testing to the flow of real gases. To determine the effects of wellbore storage and turbulence on well test interpretation, we developed a finite-difference model to simulate well test conditions. Since gas wells usually are widely spaced and have high compressibility, the emphasis has been put on the early transient behavior before the effects of the outer boundary are noticeable at the wellbore. The Mathematical Model The geometry of our mathematical model is similar to that used by Prats.4 The well is centered in a circular uniform reservoir. A vertical fracture of infinite flow capacity penetrates the formation and passes through the wellbore. The wellbore itself is not important. Fig. 1 shows a sketch of the problem. Fig. 2 shows the idealized model. The equation for the flow of real gas in a porous medium with uniform porosity, permeability and thickness is5-7

Jan 1, 1970

By Herbert Dlaska

The BBU - rotary hearth treats lead concentrates and battery scrap by the roast-reaction process. It corresponds in principle to the long-known Newnam hearth, however its hearth-basin is not straight but curved to a closed ring. In operation this annular hearth is filled with liquid lead and rotates around a central blast-box. The charge, heated to a glowing-red, floats on top of the lead bath, into which air is blown from the blast-box through a horizontal slot-type tuyere. Ore pellets and brown coal are continuously charged onto the reacting mass from two storage bins. Lead is set free by the roasting reactions and trickles through the charge into the lead bath from where it is tapped from time to time. The reacting mass is continuously stirred by a mechanical agitator and backed, by a mechanical shovel, against the water-jacketed wall of the blast-box. The gangue of the charge forms lumps of scorified character, the so-called hearth slag or grey slag, which are discharged from the hearth. The waste gases are collected in a hood and conducted to a baghouse from where the fumes and dust are automatically transported to the pelletizing installation and are recycled with new material. The daily output of lead bullion depends mainly on the lead content of the charge. With lead concentrates containing 74% lead, about 24 tons of lead bullion per day are produced on the hearth at a direct lead recovery of about 89 per cent. Approximately 10 per cent of the lead content of the new material passes into the hearth slag from where it can be recovered in a blast furnace or in a rotary furnace. For small lead smelters the BBU-process represents the most economical way of melting high-grade lead concentrates. The process requires a relatively small capital investment, consumes little fuel, utilizes cheap fuel and is very flexible. Further, of great importance, is the fact that battery scrap can be treated by the BBU-process with very good results.

Jan 1, 1970

By Lloyd B. Underwood

Dr. Gardener, in Chapter 2, has presented a comprehensive state-of-the- art review of site investigations For tunneling. Nearly all of the techniques he discussed will also be required for future site investigations. Therefore, this chapter will be devoted to a few rather new exploration techniques plus ideas for improving some of the present-day methods. In March 1962, the first symposium on "Remote Sensing of Environment" was held at the University of Michigan.l Since that time, four additional symposiums have been held at the same University. Also, the technical Literature has recently included a number of articles on remote sensing techniques. A recent one appeared in the February 1968 issue of Materials Research and Standards.Vt was entitled "Developments in Remote Sensing Applicable to Airborne Engineering Surveys of Soils and Rocks," and was written by Dana C. Parker. Mr. Parker predicts that aerial reconnaissance will someday supplant soil augers, rock drills, surface reconnaissance, and geophysical surveys as the engineer&apos;s primary means of obtaining information about soils and rocks. He states, "The engineer wishing to survey a route or a site or to locate rock and soils suitable for construction projects will be able to push some buttons in an airplane and record all the data required for determining the relevant conditions. In a short time after he returns to earth with his rolls of film and charts, he will be able to reduce and analyze the data by partially computerized techniques and to compile a concise and comprehensive engineering report that gives all the relevant information about rocks, soil, water, and vegetation in the area he surveyed. Most important he will feel as confident with his recommendations, derived primarily from image characteristics and spectral power distributions, as his predecessors did with recommendations based on more tangible evidence obtained from drill cores and surface reconnaissance." The airborne sensors for engineering surveys of soils and rocks are those that sample some electromagnetic property of the materials that com- prise the terrain and cover its surface. In addition to cameras, these include

Jan 1, 1970

By S. A. Levy, J. D. Wood, J. F. Libsch

A study of the preparation and characteristics of a sevies of Fe-C-N alloys has been conducted. X-ray, microhardness, and metallographic data from a series of single-phase alloys produced by controlled nitriding of carburized foils are reported. The existence of a, y&apos;, and E carbonitride has been confirmed and it has been found that y&apos; is the hardest of these three phases. These results have been used to interpret the structures observed in nitrided steels. ThIS paper represents the second phase of a three-part study concerning combined nitriding and induction hardening. The first part&apos; reports the engineering properties (depth hardness, fatigue, corrosion, and tempering resistance) obtained when seven different steels were subjected to the combined surface hardening treatment. The present paper concerns the nature of a series of single-phase alloys prepared by controlled nitriding of carburized foils. The objective was to simulate the various layers present in the as-nitrided steels. A third paper will report data concerning induction hardening of the foils and will attempt to set forth a mechanism for the high hardness obtained with the combined treatment. Studies of nitriding generally fall into three categories. The first were performed with bars using conventional nitriding procedures, thus yielding a nitrogen gradient and a series of phase layers near the surface.2-6 Such studies were complicated by the presence of the nitrogen gradient, for it was difficult to correlate microhardness and X-ray data with chemical composition. There were always complications due to penetration of the X-ray beam which yielded data influenced by underlying layers. Similar difficulty was experienced in taking hardness readings on a tapered specimen or in isolating various layers by machining. A second group of investigations was primarily concerned with establishment of regions in the Fe-N7,9,10 or the Fe-C-N phase diagram.8 These were performed with powder specimens which were nitrided in am-monia-hydrogen mixtures to produce a series of single-phase specimens. Unfortunately, the powder specimens were not amenable to either microstruc-ture or microhardness study. The third was essentially a compromise of the first two. Bose and Hawkes," using 0.005-in.-thick iron foils, were able to obtain microhardness, microstruc-ture, composition, and X-ray data on Fe-N alloys of eutectoid composition by equilibration in ammonia-hydrogen mixtures at 1290°F. To obtain a better understanding of the nitriding process and the characteristics of the phases in ni-trided plain carbon steels, the present investigation was undertaken. The investigation was patterned after that of Bose and Hawkes with the exception that nitriding was performed at 930°F (below the eutectoid temperature), as in the case of conventional nitriding. In addition to gaining some understanding of the source of high hardness of nitrided and induction-hardened steels, found in a previous study,&apos; this investigation was concerned with the possibility of controlling the phases present in a nitrided case through the use of ammonia-hydrogen mixtures. Knowledge of the properties of each phase and the conditions necessary for its production could make it possible to avoid undesirable surface layers in nitriding. EXPERIMENTAL PROCEDURE Specimen Preparation. A specimen thickness of 0.005 in. was selected to insure that a uniform nitrogen concentration could be obtained in a reasonable length of time by equilibration in an ammonia-hydro-gen atmosphere. The starting material was a vacuum-cast ingot of pure iron, the major impurities of which were: C, 0.003 pct; 0, 0.014 pct; S, 0.004 pct; N, 0.003 pct.* &apos;Compositions are quoted as weight percent except as noted. The ingot was heated to 1500°F in a nitrogen atmosphere and forged to a slab 0.25 in. thick. The material was then reduced to 0.005 in. by alternately cold rolling and annealing in a nitrogen atmosphere at 1600°F. This material was divided into five groups of specimens which, after carburizing, yielded the following carbon contents: 0.003, 0.28, 0.36, 0.46, and 0.74 pct C. The carburizing was performed by the Leeds and Northrup Research Laboratories, using a controlled "carburizing potential" which yielded a uniform carbon concentration throughout the cross section.

Jan 1, 1970

By E. T. Turkdogan, L. S. Darken, R. J. Fruehan

Further consideration is given to the application of the quadratic formalism to evaluate the thermodynamics of binary metallic solutions from experimental data. The use of the thermodynamic relation, in(r1/r2) dN2= 0, in the evaluation of activity data is discussed. The empirical correlations derived previously for enthalpies and entropies of solutions in Part II are shown to be predicted theoretically for a special case. The applicability of the quadratic formalism to the activity coefficients for binary organic solutions is demonstrated. DARKEN&apos; introduced a quadratic formalism describing the composition dependence of the activity coefficient in the terminal regions of binary metallic solutions. In a subsequent paper (Part II) Turkdogan and Darkeen2 extended this formalism to the enthalpy and excess entropy of binary metallic solutions, and showed that the available data for the activity coefficients and heats of mixing of many solid and liquid binary metallic solutions confirm reasonable applicability of the quadratic formalism. Much variation was noted, however, in the extent of the terminal regions from one system to another, commonly from about 10 to 70 at. pct. For the present purpose, equations derived previously need be given only for one of the terminal regions, e.g. region (I), 0 < N2 < N&apos;2: where subscripts 1 and 2 indicate quantities for components 1 and 2 and superscript ° the values at infinite dilution; other terms are: N = atom fraction, y = activity coefficient, = partial molar enthalpy of solution, ?HM = molar heat of solution, ?Sx = excess partial molar entropy, ?Sx = excess molar entropy. The heat and entropy like terms (constants) el, and S12 are defined in the following expression for the temperature dependence of a12, thus a12 £12 — s12 rnl 2.303RT 2.303 R l J Using this formalism, the thermodynamics of binary systems in the terminal regions may be described over a temperature range of experisental interest in terms of eight quantities: Lº1—Lº2, ?Sx1,?Sxº2 , £12 ,£21,fiai, S12, and S21. In the previous paper, these quantities were evaluated for many solid and liquid binary solutions, and two significant correlations were observed between these thermodynamic quantities pertaining to the terminal regions, thus [10] and [11] Combining Eqs. [9], [l0], and [ll] and rearranging gives a12 -a21 = 1.382R log rº2- 0.08(?S2xº- ?S1xº) [12] Since the second term involving entropies is small and Eqs. 1101 and [ll] are empirical relations, the above equation may be simplified to a12 = 2.74 log rº2 [13] Using the values of a&apos;s and y°&apos;s compiled in Parts I and 11, a12 - a21 is plotted against log(rº2/rº1) in Fig. 1; the line drawn has a slope of 2.74. For Hg-K at 300°C, log(yº2 /yº1)= —5.10, not shown in Fig. 1, and from correlation [13], a12 - a21 = -13.97; this is to be compared with -10.76 derived from the activity data (Part II).

Jan 1, 1970

By Thomas E. Howard

Tunneling is at the threshold of a new era. An exciting new technology is becoming available. And, supplying the increasing quantities of minerals required by a growing and socially advancing world population, together with providing the subsurface facilities attendant to the rapid urbanization of the more developed countries of the world, will require underground excavation during the next decades on a scale that would have seemed fantastic a few years ago. It is estimated that world mineral consumption will increase fivefold by the year 2000. Projections for the United States indicate that domestic consumption of nonfuel minerals may increase two to three times by the end of the century. Meeting these requirements will entail opening up many new underground mines, even if present trends toward surface mining continue. And, at least in the United States, new factors that are becoming increasingly important may modify these trends. We are depleting our shallow easy- to-find and easy-to-mine mineral deposits; and, if we are to avoid becoming dangerously dependent on imports, we must turn more and more toward deeper deposits that are not amenable to surface mining. Growing public concern with environmental quality is apparently leading toward increasingly stringent regulation of surface mining which also will tend to make underground mining economically more attractive. The world market for underground construction is also growing rapidly. The most conservative projections indicate that in the United States alone more than $7.0 billion will be spent on excavation for underground facilities during the next ten years. And these estimates do not include any of the bold, imaginative new applications for underground excavation that have been proposed, such as extensive underground power transmission, the Chicago Deep Tunnel plan, and the Northeast Corridor Transportation project. There can be little doubt then that the market for tunnels for conventional applications is increasing rapidly and that the trend will continue. It

Jan 1, 1970