Search Documents

By Harry L. Washburn

Use of coal thermal dryers has steadily increased since 1928 when one of the predecessor companies of the present Consolidation Coal Cu. constructed a complete preparation plant with thermal dryers. Today there are about 25 additional preparation plants that, all together, use over 65 individual thermal dryers of almost every type. The thermal dryer is a heat generator and the unit may have a separate furnace or a firebox that is an integral part of the dryer. It is also a materials handling device that allows an intimate mixture of wet coal and hot gases with instrumentation for temperature control and. in some cases, the more difficult flow rate of hot gases. The materials handling portion of the dryer is subject to the normal wear and teal of any similar device plus effects of heat, water vapor, moisture: and, sometimes, acid. With present emphasis on air pollution. most fine coal dryers have wet scrubbers.

Jan 8, 1963

By W. L. Crentz, E. E. Donath, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By E. E. Donath, W. L. Crentz, D. Doherty

Maurice Rey—The influence of cyclone diameter upon the fineness of separation is an important point which, however, cannot be discussed adequately if the injection pressure or the rate of flow are not specified. Perhaps some light can be thrown on the matter by using the formulas derived by Dahlstrom. Let us consider several geometrically similar cyclones where the apertures e and b are equal and proportional to the diameter D and which are operated with the same pressure drop. Eq 8 of Dahlstrom's paper can be written: Q Q = K D'. " or. if F is constant: Q = K D18 K is a constant of proportionality. Introducing this value of Q in eq 13 gives elimination efficiency = K D0' " Elimination efficiency, in the terminology of Dahlstrom, means the diameter of particles, in microns, which divide equally between the underflow and the overflow. This denomination is regrettable and it would be preferable to call it diameter of separation or characteristic size or any other name connoting a size rather than an efficiency. Whatever the name used, the above equation shows a slow increase in the fineness of separation when the diameter of the cyclone decreases. For example, if a 14-in. cyclone gives a 400-mesh separation (37 microns), geometrically similar cyclones, having the same pressure drop will give separations at the sizes shown below.

Jan 1, 1951

By D. L. Murphy

As the world's demand for iron ore increases and available sources are depleted, increasing attention will be centered on deposits in the Quebec and Labrador portions of the Labrador Trough. Improvements in the beneficiation of low grade iron ore stimulate exploration for deposits amenable to concentration. This study is centered on the Mt. Wright-Lake Carheil area, lying between Wabush Lake and Mt. Reed in Quebec. Described in detail are the general lithology, structural and economic geology, and mineralogy of the iron-formation. The iron ore province of Quebec and Baffin Island extends from the southern shore of Baffin Island southeasterly through the Labrador Trough to Matonipi Lake, approximately 185 miles northwest of Seven Islands. (See Fig. 1.) Future geologic field studies will very likely extend the limits of the province to include the ferruginous and associated rocks of the Lake Mistassini area. At present, only the deposits near Knob Lake and Lake Jeannine (Mt. Reed) have been brought into production although in the near future several other properties including those at Wabush Lake will commence operations. Within the next decade or so, as the world's demand for iron ore increases and available sources are depleted, this region will undoubtedly become a major mining district. Initial reports of iron-rich rocks in Labrador date back to the investigations undertaken by A. P. Low near the turn of the century. During the ensuing years the country was prospected chiefly for precious and nonferrous base metals because of its inaccessibility and the low tenor of the iron ore. In 1945 an evaluation of the direct shipping ores near Knob Lake indicated that sufficient reserves were present to justify the enormous capital expenditure required to bring the deposits into production. Initial open-pit mining began in 1954 following the construction of a townsite, a 360-mile long railway to Seven Islands, and an elaborate loading dock. Recent improvements in the beneficiation of low-grade iron ore have stimulated widespread exploration for deposits amenable to concentration, particularly along the southwest extension of the Trough. The Mt. Wright-Lake Carheil area, bounded by longitudes 66O45' and 67 30' west and latitudes 52 30' and 52 45' north, is a nearly rectangular tract of slightly less than 500 sq miles. It is in Saguenay County, 174 miles north-northwest of Seven Islands (see Fig. 1). Except for the periods of the spring breakup and the fall freeze up, the area is readily accessible by air.

Jan 1, 1962

By W. J. Taylor

In making heating gas with anthracite coal for roasting ore during the past few years, I have tried many forms of gas generators. So far, the most successful and satisfactory one has been what we call a fluxing producer, which is simply a small cupola or blast furnace, in which we charge with the coal, say, 30 or 40 per cent. of basic blast-furnace cinder, to unite, when melted, with the ash or earthy matter in the coal, and carry it off as cinder. The producer we have in use at Chester, N. J., has more of the lines of a blast furnace than a cupola, the hearth being 24 inches diameter and 24 inches high. It then enlarges on an angle of about 25 degrees from a perpendicular to 4 feet, and then is drawn into 3 feet on top ; total height, 12 feet. We use one water coil-tuyere 12 inches above the bottom, and blow through a 1 1/2 - inch nozzle. The depth of coal above the tuyere averages about 6 feet. The producer-is blown with

Jan 1, 1881

The Institute has prepared a list of Societies' publications, magazines, . etc., which were duplicates and were discarded at the time of the consolidation of the libraries of the three Founder Societies. These books will be disposed of about March 1, 1916 by the Board of Directors of the Institute through the Library Committee. If, meanwhile, members who have incomplete sets of these books, or for any other reason desire to secure some of them, they are asked to communicate immediately with the Secretary, as this is in unusual opportunity to secure books at a very low price. American Gas Light Journal, viols. 31 to 39. American Institute of Electrical Engineers, Transactions, vols. 5 to 26. American Machinist, vols. 3 to 20, 22 to 29. American Society of Civil Engineers, Transactions, vols. 2 to 10, 21 to 24, 26 to 33, 39 to 49, 52, 55, 58, 74. Index, viols. 1 to 21. American Society of Mechanical Engineers, Transactions, vols. 1 to 28. Index, vols. 1 to 20, vols. 1 to 25.

Jan 1, 1916

By C. E. BOCKUSD

WHEN Mr. Bain asked me to lunch with you he requested that I say a few words as to how the Institute could be helpful to the bituminous coal industry. I feel like saying, "Thank you, what have you?" I do not want to trace in detail the story that is old already to many of you. On the other hand it does take some little stage-setting to illustrate what is the matter in the bituminous coal industry, a trouble that must some day be cured. There has been something over a century of bituminous coal production as a real business in this country. True, Joliet and Marquette discovered coal in Illinois in 1673, according to published accounts of their travels, and shortly thereafter Father Hennepin also found Illinois coal in 1689. Coal was mined near Richmond in 1750, and Richmond shipped coal to New York and Philadelphia in 1789. But it was not until 1838 that the production of bituminous coal in this country totaled a yearly output equal to the minimum for one class A mine today, for that was the first year that production exceeded 200,000 tons.

Jan 1, 1930

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By H. K. Work

The Bessemer process is one of the most interesting methods of making steel. At one time it was by far the most important. In recent years, however, it has steadily lost ground to the open-hearth process. The forces working against this method of stccl-making are partly economic and partly metallurgical.1 In this paper, dealing as it does with the control of the process, the metallurgical factors alone will be considered, although it is obvious that economic factors must play a part in determining the ultimate status of the Bessemer process. This discussion has been limited in another respect—it deals primarily with the acid Bessemer process in bottom-blown converters, although much of the information is applicable to basic and side-blown converters. The fact that open-hearth steel has superseded Ressemer steel to a large extent has tended to create an impression that Bessemer steel is inferior. As a matter of fact, Bessemer steel is actually superior to open-hearth for many applications.2 There are, however, definite metallurgical limitations to the use of Bessemer steel, resulting largely from two factors: (1) the physical properties conferred by nitrogen and phosphorus, and (2) the variability from blow to blow. These, of course, are not entirely independent, since some of the variability covered in the second item is undoubtedly due to nitrogen. But the variability is also caused by other factors. One of these is the relatively small size of the Bessemer heats. Because of this, a given shipment of Bessemer steel is more likely than a shipment of open-hearth steel to contain the product of several heats, each with its own distinctive and slightly different characteristics. Added to this is the fact that the refining of Bessemer steel proceeds so rapidly that the timing of the end point is limited to a matter of seconds, whereas the finishing period in the open hearth extends over a period of one or two hours and the timing of the end point may vary by several minutes without seriously affecting the product. There is no doubt that this has contributed to the variability of Bessemer steel and has led to the use of open-hearth steel in many optional applications. That Bessemer steel may vary is not necessarily objectionable, and it may even prove an advantage, providing a precise control is available to secure the desired qualities for any specific application. With this in mind, a comprehensive research program was undertaken, one phase of which was directed toward securing more accurate control of the blow. The results have been encouraging, and it is the purpose of this paper to describe a method in which modern scientific instruments, based on photocells, are currently being employed to assist the blower. The Control Problem In this day of scientific control of technical processes, where the operating

Jan 1, 1941

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. PURPOSE Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls

Jan 1, 1946

By S. Oglesby, A. L. Thomas

Until recently, probably the best means of sampling airborne dusts has been the impinger method. Dust-laden air is drawn into a sampling tube, and the particulate matters separated from the air and collected in the liquid in the impinger. A sample of the suspension is prepared on a slide and counted through a projection microscope. This method is simple and reliable, but it does suffer drawbacks. Since the collected particles must be counted visually, results of the dust count are not immediately available at the time the sample is taken. This seriously impedes studying the effectiveness of dust inhibitors, such as water sprays, or making adjustments in equipment. Greatest disadvantage of all, however, is the tedious task of counting particles in the sample. With the growing desirability of taking more samples, the effort involved in making these counts is a real factor in the cost of dust control. Finally, it is generally recognized that impinger dust counts can be related to health hazard only for specific kinds of dust and under similar conditions. This is because the rather complex mechanism of dust damage depends so much on size distribution of the dust. Counts determined by impinger samples cover a limited size range that does not necessarily corre-

Jan 1, 1960

By E. H. Bronson

PROPERTY of Malartic Gold Fields Ltd. is situaated in the great clay belt in the northern part of the Province of Quebec. This belt represents the floor of the glacial lake Barlow-Ojibway. The clay blanket has a gently rolling, almost flat surface, with here and there projecting knobs and ridges that outline the large irregularities of the surface on which the clay was deposited. At irregular intervals glacial eskers dominate the landscape. The ore-bearing country rock is covered by strata of clay, sand, and silt to a depth varying to 40 ft. There are serious structural problems when it is necessary to place loads of unequal intensities on this surface to support buildings and machinery for a modern mining plant. Earlier mining companies and their engineers paid little attention to the science of soil mechanics, partly because they believed it unnecessary and partly because they knew little of the subject. The results are evident in some of the tottering structures in older camps. Careful analysis of soil problems is well worth-while, since cost of foundations may vary from 20 to 50 pct of the final cost of a structure. Low operating and maintenance costs can be achieved only in this way.

Jan 11, 1957

By F. L. Grammer

In these day, when anthracite is less extensively used as a blastifurnace fuel than it was a generation ago, and managers endeavor to maintain regular and known ore-mixtures, the " freezing " of tuyeres, cinder-notch or iron-notch is infrequeut; and, consequently, the oil-burner or " kerosene blowpipe "* is seldom employed; and furnace-foremen have, to a considerable degree, forgotten their former cunning and persistency in the use of the drill and sledge. Still, in starting new or abandoned plants with untrained labor, and in running some of our large 100-ft. furnaces, slips, resulting in very cold furnaces, may occur, even under experienced managers. During my superintendence of the Cleveland, O., blast-furnaces, such a misfortune, owing to a dearth of trustworthy foremen, was experienced; and our electrician, Mr. Thomas Martin, proposed to open the tuyeres and cinder-notch by means of the heat of the electric arc. We have heard that the surface-cracks or marks developed in rolling heavy plates have been closed by electric welding, as by a soldering-iron, and also that an electric burner has been employed at some German blast-furnaces; but the experiment was quite novel to us; and I think it constituted one of the first, if not the very first, successful application of this device, for the purpose named, in the United States. †

Jan 1, 1902

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Allen Johnson

WITH a realization of the rapidly increasing importance of automatic stokers as a medium for domestic heating, the Anthracite Institute Labo-ratory has conducted extensive investigations, over a period of several years, to determine the various outstanding characteristics of stoker design and performance. The purpose of this paper is to summarize these findings as a guide to current practices. STOKERS INVESTIGATED One or more models of the underfeed stokers listed below were included in the various phases of this investigation: Beckley Gilkoal Burnwell Iron Fireman Combustioneer Motor Stokor Electric Furnace Man Norristown Super-Stoker Erie Heat Generator Whitney Fire Ball (Tests Incomplete.) Fuel Saver Principles of Construction.-The operating principle of the leading makes of underfeed stokers is similar (Fig. 1). A plungers, or slowly revolving worm2, conveys the buckwheat or rice sizes of anthracite to the center of a specially constructed tuyere pot where air is admitted to the coal. through suitable ports of varying design. As the fuel burns, it is slowly forced to the outside circumference of the tuyere by the pressure of the incoming coal; eventually the ash falls over the edge of the pot, either entirely by gravity or aided by mechanical sweepers. In at least one model, the entire firepot revolves. While various special details have been included in the design of a number of stokers, they do not affect the ,general principles as described above, and therefore have not been included in this discussion.

Jan 1, 1935

By W. W. Little

At the United Verde mine the 9-2D stope on the 4050 ft level is located within the north sulphide mass lying some 800 ft north of the main sulphide ore body. In 1948 it was estimated that this block contained 85,000 tons of ore at 4% copper and 9.2% zinc. The north ore body is a lenticular replacement deposit in the black schist, extending from about 100 ft above the 3750 level to a distance below the 4500 level yet to be determined. Although the mineralized zone approaches 1000 ft in length, only 300 ft is of economic importance. In width it varies from a maximum of 60 ft to about 3 ft at the north end, and is characterized by pinching and swelling in the ore zone. One of these larger swells is being mined as the 9-2D stope. Mining costs at greater depth, together with the expected grade of ore after dilution, necessitated a low cost mining method to permit profitable stoping operations. Based on the results obtained in a number of Canadian mines, it was decided to develop the ore body for stoping by the Aldermac or bench method of diamond drill blastholes; however, this plan was subsequently changed and the radial or ring method adopted. Such a method seemed to offer the advantage of large tonnages at low cost, and obviate the necessity of waste fill. This latter point was of particular importance, since the present waste system does not extend below the 3000 level.

Jan 4, 1950

By A. T. Schwennesen

(Wilkes-Barre Meeting, June, 1911.) EVERY engineer has occasion to trace or copy a map, plan, or other drawing on paper too thick for the ordinary way of using tracing-cloth or tracing-paper. When the figure is small and simple a copy may be made by holding the original against a window-pane, covering it with the paper, and tracing direct by the aid of the strong sunlight from outside. The need of utilizing this principle on a larger scale and in a more convenient position led Dr. J. C. Branner to plan the table of which the following is a description: This table was first made in the form of an adjustable glass-top table with a mirror beneath, in 1887, while Dr. Branner was State Geologist of Arkansas. Later it was modified as experience suggested until the form as here described was evolved. The device consists essentially of a drafting-table with a plate-glass top, upon which the original drawing and the paper are laid, and a mirror mounted underneath to reflect the light of the sky up through the drawing. The glass top is hinged and fitted with two arms and thumb-screws, so that it can be raised and fixed to any position, either inclined or horizontal. The mirror is pivoted and revolves about a horizontal axis, so that it may be tilted to any angle. The hood of cardboard or black cloth prevents the reflection of light from the tracing, and may or may not be attached to the table. The apparatus is set up before a window through which part of the unobstructed sky is visible. The mirror is then adjusted like the reflector of a microscope, so that the skylight is reflected up through the drawing. If the mirror can be so located that the direct rays of the sun are reflected through the drawings, thicker paper can be used. The map or drawing may be held in place by clips screwed

May 1, 1911

D. J. DEMOREST,* Washington, D. C. (written discussion ?).-This paper is a real contribution to technical science; it will make it&apos; easier to think accurately about the inner workings of a blast furnace. I was rather surprised to read that the authors regarded as a new discovery the idea that a molten mixture of CaO, A1203, and Si02 is a molten solution of the compounds of these oxides rather than of the oxides in each other. Surely no. chemist with an active respect for the known facts of chemical affinity could believe that these oxides could be melted together without forming compounds, and that these compounds would then dissolve in one another. This work does, however, help to establish what it was supposed must be true. I think it is worth while, in the light of the work of the Geophysics Laboratory, this work of the Bureau of Mines, and that of previous investigators, to visualize what happens as a charge passes down through a blast furnace, thinking especially of the slag-forming materials. These are chiefly kaolin (Al203.2SiO2.2H2O), quartz, and limestone. These substances do not undergo much change until the limestone decomposes at about the middle of the furnace, whereupon the chemical affinities of CaO and SiO2 must begin to he active; especially if there is any amorphous Si02 present. This forms CaSiO3, and the SiO2, CaSi02 and Al2-032SiO2 then come together to form the binary and ternary eutectics so well located by the work of the Geophysics Laboratory. No matter how much lime has been charged into the furnace, the formation of this eutectic will start it about the same height in the furnace and the gangue will start to get pasty at the same height. If the charge is such that the

Jan 4, 1918