Search Documents

By James E. Lawver

Efficiency of industrial research and development depends on the ability of engineers and scientists to collect and present data to top management for decisions. In many cases, the data presented are so deceptive that management makes costly wrong decisions. Since management personnel often are selected on the basis of higher administrative quality than technical ability, it is the responsibility of the industrial scientist or research engineer to make certain that the data presented tell a completely ac- curate story of each industrial problem. It is rare that misleading data are deliberately presented, but when this is done, it is? of course, dishonest. The rise of deceptive data usually stems from the lack of knowledge of experimental design and statistical methods of analysis. Most of the better chemical engineering schools have recognized the need for courses in industrial experimentation and many of them offer complete courses at both graduate and un- dergrarluate levels. By contrast, many of the mining and metallurgical schools have not recognized the importance of industrial experimentation courses and some of them, in fact, do not allow credit toward a mining or metallurgical engineering degree for statistical courses even when taken as an elective. The sole purpose of this paper is to make a plea for mining and metallurgical schools to present required industrial. statistical courses for their graduates. It is true that fine industrial research has been accomplished in the past without the assistance of any statistical techniques. Industrial problems have also been solved without the use of digital or analog computers, electron microscopes or other modern conveniences. The fact remains, however, that the correct use of these modern tools tends to reduce the cost of research and to eliminate costly errors. A working knowledge of experimental design and statistical data analysis must simply be viewed as a valuable tool whose proper use will greatly reduce the cost of experimentation and minimize the cost of false conclusions. These statistical methods, however, simply cannot replace fundamental knowledge or, for that matter, "good horse sense". Nevertheless. an experimenter armed with fundamental knowledge and good horse sense but completely ignorant of elementary statistical techniques, may easily present his data in such a deceptive form to cause management to make incorrect decisions.

Jan 6, 1962

By J. R. Campbell

It is the purpose of this paper to review somewhat in detail the literature on the subject that is extant, which ought to provoke considerable beneficial discussion. The value of 1 per cent. ash in blast-furnace practice was brought to the attention of the writer when he was connected with the U. S. Steel Corpn. Various groups of blast furnaces in the Pittsburgh district compiled a statement in which the average saving was about 6 c. per ton on pig iron for every 1 per cent. of ash reduction. Later, the same groups of furnaces, when materials had reached a higher price, compiled a statement in which there was a 30-cent saving on pig iron for every 4 per cent. ash reduction in the Pittsburgh district, which was equivalent to 7½ c. for every 1 per cent. ash reduction. In the Chicago district, on long freight hauls of coal and coke from the Pocahontas district, the set-up was 30 c. per ton of pig iron for every 2 per cent. ash reduction, or 15 c. for every 1 per cent. Some years ago, Ralph H. Sweetser, of the American Rolling Mill Co., presented a paper which provoked considerable comment.' To get the matter again before this body a résumé of his computations is given below: Comparison of Pig Iron Costs Ash in Coal. Ash in CoKe, Fixed Carbon in Coke peR Ton OB PIG Iron peN Day, Per Cent. PeR CeNt. Coke. Per Cent. PIG IRon. Lb. Tons 6.00 8.70 89.80 1800 365.0 7.00 10.15 88.35 1860 353.2 Coke with 8.70 Per Cent. Ash Ore mixture, 4144 It). = 1.85 tons @ $5.50.............................. $10.17 Coke, 1800 lb. = 0.90 ton @ $6.50..................................... 5.85 Limestone, 1000 lb. = 0.50 ton @ $1.50................................. 0.75 Labor, $365 per day on 365 tons....................................... 1.00 Supplies and service, $250 per day...................................... 0.68 Overhead, $200 per day............................................... 0.55 Reserve for relining and depreciation................................... 1.00 Total............................................................. $20.00

Jan 1, 1931

By d&apos, John C. Entremont

Pure iron was inductively melted in small refractory crucibles and optical pyrometer and immersion thermocouple readings were simultmzeously taken. The resulting emissivities of the liquid iron surface obtained were found to be greatly affected by both the gaseous atmosphere and geometrical changes in the physical setup. Quantitative values for these effects are indicated. FOR many applications in both the laboratory and plant, optical pyrometry is still the best means of measuring temperatures in the incandescent range. A prerequisite in evaluating the correct temperature is a good value of the emissivity of the surface. To obtain the emissivity from the tabulated values of the literature can be very confusing and often far from correct. There are many reasons for these difficulties, and it is not within the scope of this paper either to enumerate or to discuss them all. Its purpose is to show quantitatively how several factors affect the apparent emissivities obtained from experimental measurements on liquid iron surfaces. The black body is the reference state for the quantitative values of emissivities and is defined1 as a body which absorbs all radiation incident on it, reflecting none; such a surface emits more radiation per unit area per unit time than any surface which reflects any radiation, and is given a value of unit emissivity. All bodies having reflective power thus have emissivities less than unity and are considered nonblack or grey bodies. The ratio of the radiant energy emitted by the flat, nonblack surface to that of a perfectly black surface of equal area and temperature is the emissivity of the surface. The above definitions are applied to flat, polished, opaque surfaces, very seldom encountered in actual measurements, and for this reason many authors have suggested that the word "emittance" be used for real bodies rather than emissivity. The emittance has reference to the material and its configuration rather than to its properties in the idealized state. Recent observations of molten iron in a small refractory crucible indicate that not only the configuration of its surface but the geometrical arrangement of its surrounding and the nature of the surrounding atmosphere have a pronounced effect on the emittance. Neglect of changes in such conditions may lead to errors as large as 40°C at 1600°C. Thus it is suggested that the term "apparent emissivity" be used and that it be recognized that its value pertains to a particular experimental arrangement only. As a result of not recognizing these differences in emissivities, which are obtainable from changes in the physical setup of an observation, many investigators have incorrectly quoted their values as those of the emissivities of particular materials rather than as an apparent emissivity for their particular arrangements. As a consequence, values of the emissivity of liquid iron ranging from 0.3 up to 0.55 are found in the literature. In an effort to establish an accurate optical temperature scale for liquid iron solutions in which de-oxidation studies were to be carried out, it was observed that the temperature relationship, obtained by simultaneously taking immersion thermocouple

Jan 1, 1963

By C. F. Knutson, Martin Felsenthal, J. D. Lung, J. D. Sudbury

This paper has been written to summarize the laboratory and field studies leading to injection of Pacific Ocean water into the Third Grubb formation. Laboratory tests for studying the permeabilities of cores to Pacific Ocean water are described. Resu1ts of these tests showed that the water could be successfully injected if it is chertzically stable, sterile, and properly filtered. Clay swelling was shown to be a comparatively minor factor in permeability reduction. Studies leading to development of an economical system for properly conditioning the ocean water are discussed. It was necessary to control pH, calcium carbonate deposition, bacterial growth, iron solubility. oxygen, and suspended .solids. A relatively simple system combining the use of sulifur dioxide, a quaternary rlmmonium chloride, and filtration was shown to adeqrrately control all these factors. This combination has not previozrsly been used as a water treating technique. Evaluation tests of the water conditioning system prior to injection are described, and results of such tests are presented. Control measures needed to insure a continusously adequate water treatment are reviewed. INTRODUCTION The utilization of sea water for waterflooding has only recently been attempted. Knowledge of treating requirements has been limited, and in most cases no water treating has been done. Prior to the initiation of the Third Grubb zone pilot water flood at Ventura, Calif.,1,2 extensive laboratory research was done in an effort to define the treatment necessary to provide a suitable injection fluid. Close coordination and cooperation between field and research personnel were found to be the foremost requisites in developing the most economical and practical method for treating ocean water. LABORATORY STUDIES Plugging Tendencies of Untreated Ocean Water A program of laboratory studies was initiated for the purpose of evaluating whether ocean water could be injected into the formation for prolonged periods of time without causing plugging of the pore spaces of the formation. Because of the fairly low permeability of the formation (averaging about 40 md), it was realized from the outset that a water of exceptionally high quality was needed. Ocean water used in the laboratory studies was carefully filtered through ultrafine fritted glass filters, having nominal maximum pore sizes of 1.4 microns. Permeability tests were then performed on representative core material from the formation. It soon became apparent in these tests that filtration alone was not a sufficient treatment for the ocean water. Prolonged injection of the filtered water caused rapid plugging of the core samples. The permeability decline of a typical sample is illustrated by Curve A in Fig. 1. The several factors which can contribute to this plugging tendency are briefly reviewed below: Interaction with Formation Clays An evaluation of clay swelling effects on liquid permeability was made using core samples from the Grubb formation. An oil was chosen for determining the reference liquid permeability because it would not tend to react with any clays that might be present in the formation. The samples were then extracted, dried, and resat-urated with either treated ocean water, formation water, or fresh water. Permeabilities to the various waters were then determined. Results of this test series are summarized in Fig. 7. The difference between the oil permeability and water

Jan 1, 1957

By Robert Gillham, Victoria Yablonsky, Grover R. Castle

INTRODUCTION The commercial paper market, unique to the United States, is a direct exchange of funds between high-grade borrowers and large lenders; because it eliminates both the bank's role as middleman and also some significant transaction costs, commercial paper is the lowest cost short term instrument in the world. For this reason, virtually all borrowers would like to enter the market, but only issuers with the highest rating from Moody's and Standard & Poor can attract purchasers at the best rates. COMMERCIAL PAPER The commercial paper market, in existence for over 100 years, has traditionally been used for short-term financings, with most paper maturing within 30-45 days. Under the U. S. Securities Act of 1933, (section 3(a)3) industrial paper can avoid registration only if it matures within 270 days and is used for current transactions. It was first used to finance the short-term seasonal working capital needs of manufacturing companies. Since World War II, commercial paper use has grown steadily, serving in the 1950's as the market in which finance companies financed the explosion in consumer credit purchases of heavy consumer durables. LETTER OF CREDIT BACKING As far as is known, the use of letters of credit to support energy-related commercial paper began about 13 years ago with an arrangement to finance the nuclear fuel for Con Edison's Indian Point 3 Plant. Goldman, Sachs was the architect of this financing and Chemical Bank provided the letter of credit support. After an early burst of interest, this type of financing wobbled severely in the difficult credit markets of the mid-seventies before regaining serious momentum in 1976 and 1977. A mining project would not normally qualify as a borrower in the commercial paper market because of its credit standing and because its large capital needs require long term financing. However, lately, commercial paper has begun to take the place of a bank term loan in limited recourse project financings. L/C backed commercial paper took this new and startling turn in 1982 when it was used as part of the $700 million financing for the development of the Newlands-Collinsville coal mines of Mount Isa Mines Ltd. in Australia. This was the first use of L/C backed commercial paper in a long-term limited recourse project financing. First Boston acted as financial advisor and, again, Chemical Bank provided sole letter of credit support of $155 million. The $785 million BHP financing for the acquisition of the Queensland (Australia) coal assets of Utah International from General Electric Company followed the next year; there we acted with two other Front Banks to provide $270 million of L/C support. These two important transactions indicate that not only has commercial paper become an integral part of a long-term financing package, but also that it is no longer the exclusive domain of the best known U. S. companies. Lesser-rated companies and a multitude of foreign borrowers have gained access to this "exclusive club." How has this become possible? OPERATION OF AN L/C An instrument of the commercial banks, the "direct pay" letter of credit, has enabled lesser-rated companies to issue commercial paper in their own names. The letter of credit allows the issuer to substitute the credit rating of the supporting bank for its own. The L/C in effect allows a lesser-rated company to rent the bank's credit rating. This upgrading is possible because the bank is unconditionally obliged to pay the note-holders at maturity and then turn to the Issuer for reimbursement. The Issuer commonly "rolls over" a new short-term issue and reimburses the supporting bank from the sale of the new issue until cash flows from the project allow the borrower to reduce the level of paper outstanding. The commitment for an L/C facility, up to 12 years in the case of the Broken Hill transaction, governs the life of the commercial paper tranche of the financing. The term of the L/C commitment thus has the power to extend the ordinary 30-45

Jan 1, 1985

By R. V. Ramani, R. D. Zigmond, R. L. Frantz

In this paper, a computer program for determining the capital and operating costs for coal preparation plants is described along with its applications. The logic of the computer program is based upon the results of a survey of existing preparation plants, operators, plant contractors, equipment manufacturers, and consulting firms. This survey provided information on plant performance, order-of-magnitude costs, and costing procedures. Additionally, an extensive cost data file for the major capital equipment in coal preparation plants has been developed. Using the washability data and the computer program out- puts, the cleaning costs per million Btu can be calculated. Details about the program and its applications can be found in a report by the authors (Zigmond et al., 1979).

Jan 1, 1983

By George L. Atwood, William Brown

Phosphate ore is being mined at Monsanto Co.'s Henry mine, near Soda Springs, Idaho, for the company's three furnace elemental phosphorus plant near Soda Springs. The finished product from the furnaces is elemental phosphorus which is subsequently used in the manufacture of detergents, food preservatives, fire retardants and other consumer items. In stripping and mining, D-9 crawler tractors are utilized to rip and push-load rubber-tired scrapers. The equipment consists of six D-9G crawler tractors, four Caterpillar 657B scrapers, eight Euclid S-24 scrapers, one Reich T750 drill and one Caterpillar No. 16 patrol plus various support equipment. Stripping is performed on a 12- month basis, two shifts per day, whereas mining is mainly in the summer months on a one-shift basis. The hauling season begins May 15 and ends November 1 due to freezing weather and snow conditions. Annual production is 1 million tons of phosphate rock and 2.5-3 million cu yd of stripping. Stripping, mining and hauling is performed for Monsanto by Dravo-Soda Springs, a mining contractor which owns, operates and maintains all equipment used. The contractor is paid for stripping by the bank yard and for ore mined and hauled on a tonnage basis.

Jan 8, 1972

By J. E. Campbell, G. D. Calkins, N. M. Ewbank, M. Pobereskin, A. Wesner

GRINDING for size reduction affects the economics of many processes and products. It is essential as the first step in many industrial processes and is also a finishing step for materials with properties depending on particle size, such as talc, cement, and silica sand. Intermediate and fine grinding are vital operations in the U. S. cement industry, which is producing more than 250 million bbl of cement per year.' Wear of the grinding media is a large part of the grinding operation cost. Problems encountered in grinding cement are so complex that evaluation of efficiency and economy of grinding media is difficult.2 It has been especially difficult to evaluate the relative effectiveness of different types of balls because there are no good testing techniques. Many other industrial operations can be evaluated on a laboratory scale with reasonable accuracy. This does not hold true for evaluation of grinding balls. The consistent results obtained in a laboratory test under a given set of conditions are not always borne out in field application. Rough evaluations of the effectiveness of various compositions and types of grinding balls have been made in the field by using a full charge of one type in a mill and comparing the production record with another run using another type of ball. This method is time-consuming and not very precise, as the second run may not have been carried out under identical conditions. Laboratory-scale tests, on the other hand, have yielded inconclusive results, and many investigators have turned their attention to the development of a field testing technique. Field testing small sample lots of grinding balls has been impractical because it is difficult to identify and recover the test specimens from the grinding mill, and individual groups of balls that have undergone different heat treatments can not be separated.".4 To overcome these difficulties, previous investigators have identified the balls by distinctive marks, notches, and drilled holes, but this procedure has three serious drawbacks: 1) Grinding characteristics and quality of the steel balls may be affected. 2) Physical markings may be worn away in the grinding process, especially during a prolonged run. 3) Recovery from the bulk of the charge will be extremely difficult because the markings are hard to see and may be masked by a coating of the product. To circumvent these difficulties, a radioactive-tracer technique was proposed for recovery and separation of steel grinding balls and subsequent evaluation of the various compositions of the balls. The proposed technique involved five basic operations: 1) Thermal-neutron irradiation activation5 of each group of test grinding balls to a different level of specific radioactivity. 2) Addition of groups of radioactive steel-ball specimens into a ball tube mill. 3) Recovery of radioactive steel-ball specimens from the bulk of the mill charge. 4) Separation of the various groups by their specific radioactivity. 5) Evaluation of actual grinding ball wear. Before any physical tests were performed, required neutron irradiation intensity and time were calculated. Probable composition of the steels to be used was ascertained. An examination was made of the radioactive nuclides8 to be formed which would contribute measurably to the radiation level immediately after irradiation and during the test operation. The radioisotopes formed, their types of radiation, and their half lives are listed in Table I. Of these radioisotopes only iron-59 and chromium-51 were significant for the actual wear test. The intensity of radiation that could be detected by a Geiger counter when the test was completed was the basis for the minimum activation level established. The intensity of radiaton that could be safely handled at the beginning of the test was the basis for the maximum activation level, although this was not considered a major problem. Ten groups of grinding balls of various composition and/or surface or heat treatment were to be tested. One group was designated for the minimum irradiation time. The remaining groups were designated for irradiation periods that increased by increments of 33 pct from that of each preceding group. This difference was considered enough for separation and identification of the groups by comparison of specific activity. Potential Hazards: Possible radiation hazards that might be encountered during this experiment were evaluated for the three important phases: 1) the radiation hazard of placing balls and removing them from the mill, 2) contamination of the product cement by radioactive material worn from the balls, and 3) contamination of the steel by the radioactive balls left in the mill. The radiation intensity expected from the whole group of radioactive balls was calculated to be 250 milliroentgen per hr at 1 ft. This meant the balls would require special shielded packaging and warning labels on the shipping containers. In a radiation field of 250 mr per hr a man can work for 1 hr without exceeding maximum permissible weekly exposure. Since the balls could be dumped into the mill in a matter of seconds, relatively little radiation exposure was anticipated at this stage of the operation. If the weight loss in the balls was 7.7 pct per month and the cement feed through the mill was

Jan 1, 1958

By Kerstin Malmqvist

A prospecting project for deep-seated sulphide ore bodies will be expensive and means a considerable economic risk. The high costs depend on the demand for extensive drilling. It is therefore important to find effective methods to estimate the outcome of different prospecting strategies. The results from a preliminary study of the possibility of using mathematical methods for this purpose are presented. We have found that mathematical methods, especially simulation technique, might be an important tool in such exploration work. A mathematical model of an ore field and of a drilling procedure has been constructed. A set of parameters describes the geometry, the size distribution and the intensity of ore bodies. Another set describes the geometry and the intensity of drill holes. Some preliminary results are given of Monte-Carlo simulations and probability calculations.

Jan 1, 1977

By M. L. White, J. L. Shafer, C. L. Caenepeel

Often an in situ leach is the only practical economic method for copper recovery from small low grade oxide deposits. The decision to develop a copper property by an in situ blast and leach is strongly dependent on ore grade, tonnage, hydrology, and the copper extraction and acid consumption rates. The inherent leachability of the ore will in part determine the desired amount of fracturing of the ore deposit by the blast in order to obtain a copper extraction rate that is economical. For the last several years Occidental Research Corp. (ORC), has undertaken a modest effort to address the question of how to best identify and determine the information necessary to predict and control the operation of an in situ leach for the economic recovery of copper.

Jan 2, 1979

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400' to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report' with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By Z. T. Bieniawski, E. Unal, H. Reginald Hardy

INTRODUCTION Rock bolts are a major means of support in underground coal mines in the United States. However, two of the most crucial problems facing the mining engineer today are that of finding a well defined and standard method for testing the anchoring ability of rock bolts, and of selecting the most suitable type of rock bolt and bolting pattern for a particular mine or specific mine section (Anon., 1982). Such selection requires not only an understanding of the behavior of the rock mass and the rock-bolt unit itself, but also a knowledge of the basic mechanisms by which rock bolts provide support while they interact with the rock mass during various field loading conditions. A recent study in this area has shown the inadequacy of present methods used in selecting and testing of rock bolts and the lack of clearly defined guidelines for safe and economical design of bolting patterns (Bieniawski, et al., 1980). The present paper describes a research study aimed at developing laboratory instrumentation and associated techniques for the evaluation of bolt-rock interaction. The instrumentation system developed, procedures followed during various experiments, and typical results from a series of studies carried out on mechanical bolts are presented. DEVELOPMENT OF THE ROCK BOLT TESTING FACILITY General A block diagram of the experimental facilities are shown in Fig. 1. The system consists of three main sections. The first

Jan 1, 1982

By T. Okubo

Gold is generally recovered from silver anode slime by electrolysis in the final step of the copper anode slime treatment. In the present investigation, rapid and direct hydrometallurgical separation and recovery of gold in the early step of the process is studied. Gold is recovered just after the elimination of copper and selenium from copper anode slime. The studied process consists of: (a) oxidizing roasting for selenium elimination, (b) sulfuric acid leaching of the calcine for copper removal, reduction of gold in the liquor by the use of proper reductant such as hydrogen peroxide (production of gold powder), (el nitric acid treatment of gold powder for further purification and (f) melting and casting of gold. Laboratory and miniplant testwork showed that the extraction ratio of gold by chlorine leaching was 99 % up and four nine gold ingot could be recovered without electrolyses.

Jan 1, 1984

By I. L. Nichols, D. C. Seidel, D. E. Traut

A fluidized countercurrent ion-exchange system was developed, operated, and evaluated by the Bureau of Mines. The system consisted of integrated multiple-compartment absorption and elution columns in which the solution flows are continuous except for short periods when resin increments are withdrawn. The exchange of uranyl sulfate between a simulated acid leach uranium solution and a strong-base, ion-exchange resin together with the subsequent elution with an acidified sodium chloride solution was studied. The effects of the number of sections, section heights, amount of resin withdrawal, and solution flow rates were investigated. Also examined were the kinetic and equilibrium relationships for the absorption step. The experimental data indicate a strong interdependence between variables. Solution retention time appears to be a major limiting variable. The column was efficient over a range of conditions, but close control was needed for optimum operation.

Jan 1, 1977

By J. L. Bruce, G. W. Nicolson

THE country rock of the Mavrovouni mine of the Cyprus Mines Corp. is hydrothermally altered, disintegrated pillow lava, with very little tensile strength ("short" ground). In places, especially when wet, it is heavy ground, though not extremely heavy except where movement has been caused by underlying or nearby stoping operations. Damage by caving from roof or sides of galleries is not sudden but progressively faster when the size of the cave increases as a result of the fall of small pieces. CEMENT AND CONCRETE LININGS During early operations, galleries in the country rock were supported by customary mine-timbering methods. Available timber, however, was of poor quality and of relatively high price, and replacements were frequent and expensive. Furthermore, the massive sulphide ore bodies required large volumes of fresh air for ventilation and cooling, and it was therefore desirable to provide smooth-lined galleries with low resistance for the introduction of air to the ore bodies. It was also desirable to eliminate hazards of fire in shafts and underground workings insofar as this would be practical. Cement and concrete were relatively cheap, and plans for using these in support of shafts, underground galleries, raises, and chutes, were developed steadily. Circular shafts with diameters ranging from 10 to 15 ft were adopted for all permanent shafts and airways. In places these were lined with concrete poured behind sectional pressed-steel forms especially constructed for this purpose. In other places, they were lined with precast-concrete blocks. It was found that such precast concrete of good quality could be produced on mass production scale and delivered at the mine from most favorable point of manufacture, at a cost of about 25 cents per cubic foot of concrete. This refers to prewar costs. As the use of concrete blocks in circular lined galleries was developed, it was found that there were very great advantages in the reduction of air resistance as compared with customary timber supports. After best methods had been developed, it was found that breakage and replacements were extraordinarily low, averaging only about 1 ½ pct per year during a period of about 15 years. Furthermore, it has been possible to reclaim for re-use a very large percentage of the concrete blocks from abandoned galleries. During the history of the operations precast-concrete blocks have been used for lining shafts, raises, ore chutes, galleries, and shaft stations, ranging from 3 to 16 ft id. The thickness of lining has varied from 5 to 10 in.; with I2 in. thickness in a few cases. Junctions of two galleries at angles ranging from about 30 to 60° are usually made of poured concrete behind sectional forms, or of a combination of poured concrete and precast blocks. In nearly all cases it has been found advisable to make the point of the wedge at the junction, of

Jan 1, 1947

By Paul D. Merica

One of the most useful, and at the same time least commonly used, methods of thermal analysis for the determination of transformations in metals and alloys consists in the recording of the time intervals required for successive increments of temperature change during heating or cooling, the temperature of the furnace containing the specimen being altered at a uniform rate. The curve obtained by plotting these time intervals as a function of the mean temperature of the specimen durnig the interval is called the inverse-rate curve. It is probably due to the fact that no simple and convenient method has apparently been available for the measurement of the successive time intervals that this method has not been so generally used as, for example, the differential method, for which several types of automatic or semi-automatic apparatus have been designed. Whenever this method has been used, the intervals have usually been measured with the use of a chronograph; its operation as practised at the Bureau of Standards1 is as follows: The temperature of the specimen is measured by a thermocouple and a dial potentiometer. The operator sets the potentiometer at successive values of the electromotive force differing by equal increments, usually 0.02 millivolt, and records the exact instant on the chronograph, by pressing a contact key, at which the galvanometer coil passes through its null position. Two-second intervals are also recorded on the chronograph record, and the number of seconds elapsing between successive signals is afterward counted from the record and plotted as a function of the electromotive force or of the temperature. This is an admirable method and by it most minute thermal arrests may be detected, but it requires a good chronograph, which is generally difficult to obtain, and the time of one operator during the recording and, subsequently, to read the intervals from the record; the latter operation often takes from one to two hours. There is here suggested a simple, convenient, and, it is believed, equally accurate method of recording the successive time intervals, by which the

Jan 1, 1921

By N. De Nevers

A calculation method has been developed for carbonated water flooding. This method takes into account the effects of oil viscosity reduction and oil swelling, due to carbon dioxide transferred to the reservoir oil from the carbonated flood water. It shows the effect of changes in carbonation pressure and carbonated water slug size. The method is based on a Buckley-Leverett-type linear flow model. The mathematical approach is similar to that developed by Welge, et al, for enriched gas drives. However, it contains a very important advance over the previous papers in its solution to the problem of injection of a "slug" of carbonated water rather than continuous injection of fluid of constant composition. The method also shows the chromatographic nature of the transport of Co 2 in a carbonated water flood. Sample calculations indicate that viscosity reduction is the most important source of incremental oil recovery. Swelling contributes to a lesser extent. Raising the carbonation pressure increases recovery, but this effect diminishes as pressure is increased. increasing the slug size also increases recovery, but again this effect diminishes as slug size is increased. INTRODUCTION In recent years there has been considerable interest in carbonated water flooding as a secondary recovery method. Several carbonated waterflood field tests are now in progress.1'3 Yet there is no published method for predicting the results of a carbonated water flood. This paper presents a method for predicting the oil recovery for ; carbonated water flood. In a carbonated water flood. a carbonated water slug is injected into the reservoir. Then this slug is driven forward by injecting plain water behind it. The field operator must choose the carbonated water slug size and the CO2:water ratio in the slug. The calculation method presented here shows the effects of both slug size and CO2:water ratio on oil recovery. The calculation assumes that the addition of carbon dioxide to flood water increases the oil recovery by two mechanisms: 1. Carbon dioxide transfers from the flood water to the oil, thereby reducing the viscosity of the oil. At the lower viscosity, the oil flows more readily and is more easily swept out by flood water. 2. The carbon dioxide which transfers to the oil phase causes the oil phase to swell. Assume that the residual oil saturation (volume per cent of pore space) is the same whether the oil is carbonated or not. Then the same volume will contain less stock tank oil if it is carbonated, due to oil swelling. The plain water driving the carbonated water slug forward will strip the CO2 out of this residual oil., causing this oil to shrink. This swelling-followed-by-shrinking leaves behind a lower residual oil saturation than would have been left behind by a plain water flood. Since some oils swell to almost twice their original volume at reasonable CO2 pressures, this effect may be large. Two additional benefits sometimes claimed for carbonated water flooding are: 1. Adding CO2 to flood water greatly increases the water injectivity in some cases.1 (Injectivity = BPD of water injected/ft of sand x differential bottom-hole pressure, psi.) CO2 forms a weak acid in water; injecting carbonated water is, therefore, somewhat like acid treating. If a formation responds to acid treating, it will probably have a higher injectivity for carbonated water than for plain water. Although the increased injectivity increases the profitability of a carbonated water flood over a plain water flood, it does not change the production curve based on total fluid injected. Therefore, the method presented here does not show any effect of increased injectivity. 2. It is claimed in one patent4 that carbon dioxide will react with some constituents of the oil to form detergents. These detergents are expected to increase the oil recovery. There is little data available to support this idea. The calculation method presented here takes no credit for extra oil recovery due to the formation of any such detergents.

Jan 1, 1965

By J. T. Norton, N. J. Grant, I. S., Servi

Coarse grained high purity aluminum was tested in creep at temperatures of 400° to 1200°F to develop subgrain structures. Measurements of subgrain size, distribution, and rotation were made from X-ray diffraction patterns. Subgrain size and distribution were checked metallographically and the size was compared with average slip band spacing. The slip family was determined for several specimens. THE interest and research recently evident abroad in the role of subgrain formation and polygon-ization as a contribution to the creep of metals at elevated temperatures is deserving of greater attention in this country. Such metallic subgrains can be defined as macroblocks existing within the grains. The general observation has been that the macro-blocks which belong to the same grain have a maximum difference in orientation of a few degrees. In spite of the considerable amount of work that has been done since Jenkins and Mellorl observed the "division of existing crystals into smaller units when deformation occurs at an annealing temperature," the subject of subgrain formation is only now receiving truly active discussion and investigation. The existence of subgrains has been revealed by metallographic methods, as in the work of Jenkins and Mellor,1 and by X-ray methods, first applied to this problem by Homes.' Hirst3 and Calnan and Burns4 applied the back-reflection Laue technique to the study of coarse grained specimens. Wood et al.5 and Greenough and Smith' examined the ring obtained with a back-reflection camera for the study of fine grained specimens. In addition to the above, the transmission technique was used by Wood.6 A special technique was developed by Guinier and Tennevin8 in order to improve the resolution. Metallographically, the subgrains have been observed directly on the surface of deformed specimens by Wood et al.,3 or have been made evident on repolished surfaces by applying a suitable etching reagent. The latter technique, first suggested by Lacombe and Beaujard,9 was then improved by Wyon and Crussard.10 Subgrains can be formed in single crystals after small amounts of bending followed by heating after this cold work, or during deformation at elevated temperatures. The first phenomenon was analyzed by Cahn11 for the simple case of pure bending followed by annealing. Cahn suggested a mechanism of subgrain formation based on the dislocation theory and called this phenomenon "polygonization." He extended this mechanism to the more complex case of local bending, such as the bending which may occur when a polycrystalline specimen is deformed in tension. Cahn's suggestion was later found quite consistent with the results obtained by Dunn and Daniels." An explanation has been presented recently regarding the formation of subgrains during deformation at elevated temperatures by Chang and Grant.'" In general, there are two schools of thought on the subject. One, according to Wood et al.,5 is that subgrain formation is a mechanism of deformation which is operative under certain conditions in the same way that the slip process is the mechanism of deformation which is operative under other conditions. The boundaries between the subgrains undergo a viscous flow which contributes substantially to the deformation of the material. The second, according to Cahn,13 Wyon and Crussard,10 and Chang and Grant,18 is that subgrain formation is the effect of simultaneous deformation and annealing and is,

Jan 1, 1953

By R. H. Frazier, F. W. Boulger

THE performance of welded structures is closely associated with the ductile-to-brittle transition temperature of the steel from which they are made. A low transition temperature is desirable because it indicates that the steel is less likely to fail suddenly at low ambient temperatures. Structures such as bridges, ships, storage tanks, and pipelines are usually made from hot rolled semikilled steel. Changes in rolling practice or chemical composition appear to be the most practical methods for improving the toughness of such materials. This results from the fact that production is likely to be seriously curtailed if improvements were obtained by recourse to heat treatment or complete deoxidation. This paper discusses the effect of variations in carbon and manganese contents on the properties of semikilled steels. The transition temperature, a property to which considerable importance is attached, varies with specimen configuration, testing method, and criterion of performance. Both the Navy tear test' and the keyhole Charpy test were used in the investigation. According to the terms used by Vanderbeck and Gensamer,V he tear test was used to measure a fracture transition and the Charpy test to measure a ductility transition. In either case the specimens absorb considerably less breaking energy in tests below the transition temperature than in tests above the transition temperature. Decreasing the testing temperature of notched-bar specimens seems to be equivalent in its effect to increasing the severity of loading on fabricated structures. Therefore, structures built from steels exhibiting lower transition temperatures in laboratory tests are expected to be less susceptible to sudden brittle fractures in service. Consequently, changes in composition which lowered the transition temperature of the experimental steels were judged desirable. Materials and Methods The steels for this study were made in a laboratory induction furnace and rolled to 3/4 in. plate, using a finishing temperature of 1850°F. Precautions taken to insure reproducible melting and testing practices are discussed in detail elsewhere.' All tests were made on hot rolled steels. The analyses of the experimental steels are given in Table I. The list includes steels with manganese contents ranging from 0.21 to 1.46 pct, at each of five carbon levels. The phosphorus, silicon, sulphur, and nitrogen contents of the steels are reasonably constant. The tensile and notched-bar properties of the experimental steels are presented in Table 11. Both upper and lower yield points are listed, and all values are averages for duplicate specimens. Transition temperatures based on three criteria are given. The keyhole Charpy transition temperatures are the temperatures at which the energy-temperature curves based on averages of four specimens cross the 20 and 12 ft-lb levels. Both definitions of Charpy transition temperatures have been used by other investigators. Charpy tests were made at intervals of 10°F, using a pendulum with an available striking energy of 220 ft-lb and a velocity of 18.1 ft per sec. The specimens were oriented parallel to the rolling direction and notched normal to the surface of the plates. The tear test transition temperatures are based on the usual' criterion of the highest temperature at which at least one of four specimens exhibits brittle behavior. The dimensions of the tear test specimens are shown in Fig. 1. The specimen is loaded eccentrically in tension, with pin and shackle fixtures, through the large holes while submerged in a liquid bath at the proper temperature. A specimen developing a fracture area with less than 50 pct shear or ductile texture is classed as brittle. Tear tests were made at intervals of 10°F.

Jan 1, 1955

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.