Search Documents

By Portland P. Fox, Berlen C. Moneymaker

The development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration. Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its principal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration. The Equipment The equipment generally employed in the drilling of large-diameter holes consists of a trunnion-type drill head mounted on a sliding base, which allows it to slide clear of the hole and thus permit the introduction

Jan 1, 1941

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Samuel M. Cassidy, John A. Garcia

In some districts of the bituminous coal field the problem of constructing bulkheads to seal off water under pressure is becoming increasingly important. Recently this matter has been brought very much to the front by the loss of a large Illinois mine due to failure of a bulkhead that separated it from several old, flooded mines. As this great misfortune has provoked much inquiry about proper bulkhead design, it is felt that a description of the successful and extensive water-sealing practice at three mines that have different natural conditions will be of considerable interest to those connected with properties having a present or future water problem and to engineers that may have to design safe bulkheads of economical construction. These three mines are the Saxton and Dresser, near Terre Haute, Ind., and the Hegeler, near Danville, Ill. All three have water conditions that make it necessary to regularly seal off all worked-out sections of the mine, and there are considerably over a hundred bulkheads in each. AS far as the writers know, these three mines are the only ones in the bituminous coal fields of the United States with anything like so large a number of water seals and experience, although a number of other mines are known to have a few bulkheads. More detail will be included herein on the Saxton mine than on the others, as the writers are more familiar with it. General Mining System All three of the mines use the same general panel room-and-pillar system, which consists of rooms turned both ways off room entries and a solid block of coal left on all sides of the completed panel except on the cross-entry side, where a heavier pillar is pierced by two entries for haulage and air. On completion of the panel the two entries arc sealed and the panel is then isolated from the rest of the mine. Owing to water conditions, no pillars are pulled; recovery inside the panel barrier pillars is approximately 65 per cent.

Jan 1, 1938

By Nelson Severinghaus

Crushed stone leads all industrial mineral, except cement in annual value of production in the United States. It is also interesting to note that crushed stone value is exceeded only by that of fuels, cement, and iron ore among all mineral products of this country. An industry which started with hand-sledging to produce smaller sizes of broken stone for hard surfaced improvement of roadways as designed by McAdam in England about 1815 has grown into a complex industrial giant. Most of this growth started with the invention of a mechanical rock crusher just under one hundred years age (1858) by Eli Whitney Blake. This invention made possible the production of greater tonnages of smaller sizes of broken stone and greatly accelerated its use for Macadam road pavements and for railroad ballast. Stones Used for Crushing All three of the major geologic classifications of stone, sedimentary, igneous, and metamorphic, are widely used in the production of crushed stone. Satisfactory physical and chemical properties can be found in each type so that economic availability becomes the prime determinant for development. Table 1 lists more common rocks of the three main groups with average values of specific gravity and toughness as measured by Deval test. This widely used classification was suggested by C. E. Lord, of U. S. Bureau of Public Roads. The physical properties were compiled by D. O. Woolf in "The Results of Physical Tests of Road Building Rock," U. S. Department of Agriculture, Bulletin 76. It should be noted that the figures given in Table 1 are averages. Very substantial variations in the physical properties of rocks within any one classification will occur. The solid surface of the earth was first made up of igneous rocks resulting from the solidification or crystallization of molten material upon cooling. These igneous rocks were disintegrated into sand, clay, and gravel by the weathering action of wind, water, chemicals, [ ] and temperature changes. The products of weathering were transported by wind and streams until they reached less turbulent areas such as oceans or lakes and were deposited. Chemical deposition between grains of sand or clay or the physical action of pressure and heat then solidified them into sedimentary rocks

Jan 1, 1960

By Walter Miller

DURING the second year of America's active participation in the war the main objectives of the petroleum refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for TNT production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $900,000,000 going into 100octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing.

Jan 1, 1944

By J. L. Huitt

Some of the problems associated with the acid treatment of oil wells are related to the control of the composition of formation treating acid. One test usually made at the well site is the determination of the acid concentration. Heretofore, the concentration of the acid delivered to the well site usually has been interpreted from a hydrometer measurement of the specific gravity of the acid solution. Experience has shown that this indirect measurement of acid concentration can give erroneous results. More reliable results are, of course, obtainable by the titration method; however, this method is not easily adapted to well-site testing. To overcome these objections, a device was developed for use in the field which permits determination of the concentration of treating acid both quickly and accurately at the time of the acid treatment. Its purpose was three-fold, namely, to determine: (1) the concentration of the fresh treating acid, (2) the concentration of the spent acid returning from the well, and (3) the solubility of formation samples in treating acid. The device was designed to operate on the principle of the stoichiometric relation between the calcium carbonate—hydrochloric acid reaction and the carbon dioxide gas resulting from the reaction. By confining the carbon dioxide gas within a reaction cell of the type shown in Fig. 1, the pressure inside the cell is increased. Since the pressure is an indication of the quantity of carbon dioxide gas produced, it may be used to estimate the concentration of the acid, provided an excess of calcium carbonate is used. From information on the volume of the reaction cell, the volume of acid used, and the pressure and temperature of the gas after the completion of the reaction, the concentration of the treating acid may be computed. The reaction cell is essentially a pressure vessel equipped with a pressure gage, temperature indicator. pressure release valve, and a special sample holder. Plastic and metal construction makes the cell both rugged and acid-resistant. The sample holder is so designed that a sample of calcium carbonate (or sample of carbonate rock) can be dropped into the acid

Jan 1, 1956

By C. V. Millikan

When a flowing oil well is being drilled in with cable tools, it is difficult to determine when an additional streak of pay sand is drilled. By placing a gas meter on the gas-release line from the oil and gas separator, any increase in volume of gas that comes with oil production is recorded. In addition to the better knowledge of sand conditions, these data are a valuable aid in determining the size and depth of shots, plugging off water, and estimating ultimate production. The meter also gives a record of operation while the well is drilling in; and if allowed to remain on the well after completion will give information that may lead to a more efficient recovery of the oil from the sand. A VERTICAL cross section of any oil sand will show great variation in porosity and oil content. In some sands, the entire thickness contains oil, the variation being only the degree of porosity or oil content, but more often the pay streaks are distinctly separated by shells or barren streaks. These pay strata vary in number and may be thin or thick. The total thickness of the sand may be several tens of feet while the part containing oil may be only 1 or 2 ft. thick. The amount of production is not proportional to the thickness of the sand but rather the thickness of the pay streaks. If the total thickness of the sand or the amount that can be drilled is small, or if the initial production is small, the depth at which each stratum of pay is encountered can be determined sufficiently accurately for all present economic purposes. However, when drilling through sand of considerable thickness, giving large initial production, especially where conditions necessitate that the production go through the same gas trap with that from one or more wells already producing, it is difficult to determine the depth at which the pay strata are encountered even accurately enough to guide the placing of shots, and small pay streaks are apt not to be recognized at all.

Jan 9, 1925

By R. A. Swalin, B. W. Roberts

ONSIDERABLE controversy has centered about the existence of an order-disorder transformation in alloys in the composition vicinity of 75 atomic pct Ni and 25 atomic pct Cr. All the evidence to date for such a transformation is of a rather indirect nature, since direct X-ray confirmation is difficult to obtain as a result of the small difference in X-ray scattering factors between nickel and chromium. As a result, superlattice lines would be very faint if present. Several investigators1-5 have observed anomalies in the electrical resistivity vs temperature curves of alloys in the vicinity of 25 atomic pct Cr. The observed change is characterized by a rather broad resistivity peak at about 540°C. A discontinuous drop in resistivity is normally associated with ordering. However, Taylor and Hin-ton4 have rationalized that the discrepancy could conceivably be caused by changes in the Brillouin zones upon ordering. The same investigators measured the specific heat as a function of temperature and have also observed anomalies in the vicinity of 540°C. Nordheim and Grant5 have proposed, because of the absence of superlattice lines and the absence of a discontinuity in the resistivity vs temperature curve, that long-range order is improbable and that the results could be better explained by short-range ordering. To date, however, the question has not been resolved satisfactorily. Neutron diffraction techniques provide a method for partially resolving the question since nickel and chromium have considerably different atomic scattering factors in the case of neutrons and, therefore, superlattice peaks, if ordering occurs, should be readily discernable. The results of a neutron diffraction investigation* coupled with a dilatometric in- vestigation are reported here. An alloy containing 28.0 atomic pct Cr was prepared from carbonyl nickel and electrolytic chromium in the form of a 1-in. diam x 10-in. ingot. Melting was done in an alumina crucible and casting in a graphite mold. The ingot was homogenized at 1250°C for seven days, after which a 5-in. long piece was cut into shavings in order to obtain a suitable neutron diffraction sample. Hardness samples and samples suitable for dilatometric analysis (% in. diam x 2 in.) were prepared from the remainlng piece. The neutron diffraction sample, along with a hardness sample, was annealed at 501°C for seven days, at which time the temperature was lowered to 479°C and held at this temperature for twenty-four more days. The hardness was observed to increase from 133 to 147 Vhn during the course of the annealing treatment, in qualitative agreement with Nordheim and Grant." Neutron diffraction traces taken at room temperature and at 42 °K are shown in Fig. 1. The insert shows the trace taken at room temperature with short counting times and thus only fair statistical accuracy. No evidence for superstructure reflections of Cu3Au-type ordering is observed. The statistical accuracy of the 4.2°K trace was improved by using longer counting periods. Several weak intensities are observed at small angles, including an aluminum reflection from the cryostat assembly and a very

Jan 1, 1958

By G. C. Weaver, G. T. Harley

BEDS or lenses of potash and magnesium salts are found in a thick salt section (Salado) overlain by Rustler Red Beds in several members of which water is present and from one of which the refinery process water used by International is obtained. Most of the holes drilled are less than 1000 ft. deep, but some wildcat holes have exceeded 3000 ft. Cable or rotary tools are used to drill down to the salt. When samples of water are desired the cable rig is used, but when this is not necessary, and where caving material is present, the rotary rig has an advantage. The rotary rig has a further advantage in that only one machine is required to drill and core the entire hole, whereas the cable rig must be moved off to make way for the core drill. Casing is placed in the upper section of the hole as required to shut off water, and a 5 3/16-in. string is set in the top of the salt before coring starts. With the rotary rig drilling is often carried to the salt with no casing, as drilling mud seals off caving ground and water-bearing strata, and a string of 4-in, line pipe or 4-in. flush-joint casing is landed on top of salt. Several types of gasoline-powered core rigs have been used in the field and all recover a 2 1/2-in. core. More recently the Sullivan Model 37 rotary rig has been tried, and a Sullivan Model N has been adapted to use a rotary bit in the upper section. Core is recovered in 20 ft. sections with a double-tube core barrel, and the bit used is a bottom-discharge type set with diamonds. The drilling fluid must be a saturated brine to prevent solution and etching of the minerals present. Blowouts are apt to occur from nitrogen gas trapped under the several polyhalite beds, and some have been strong enough to blow the tools out of the hole. Core recovery is practically 100per cent. All holes are plugged after drilling, with cement through the salt section and opposite each water horizon, and mud through the remainder of the hole. Cores are carefully logged and preserved, and in sections containing potash and magnesium minerals they are quartered and analyzed. The correlation of ore beds between drill holes is briefly described.

Jan 1, 1946

By W. C. Coffin

The refractory linings of open-hearth steel furnaces above the bath line are subject to severe wear not only from the heat caused by the combustion of the fuel and the reactions of the bath, but also from the melting action of the gases when not controlled and directed, and from the scouring of the oxides, etc. with which the products of combustion are charged. The framework that encases or binds the furnace is made up primarily of an iron or steel pan in which the furnace proper is built, side and end buckstays, and tie-rods. The expansion and contraction are so great and variable that the bindings may be subjected to severe stresses unless the tie-rods are carefully adjusted in heating up the furnace, but they are most affected by direct heat and usually become deformed from that cause when the lining is worn thin and, sometimes, when sections of the lining fall in and expose some of the framework. A deformed framework displaces the skewback of the roof arch and tends to distort or crush the roof. Bent buckstays deform the front wall, causing the door frames to stand away from the lining so that the gases burn between the lining and the frames, destroying both of them. Frequently the frames are attached to the buckstays; then when the latter bend the frames usually break. Preventing the distortion of the framework and maintaining the economy of the refractories are real factors in the cost of steel making. Nat only does the cost of general repairs and reconstruction add directly to the cost of steel produced, but the time lost in making repairs cuts down the steel production and increases the overhead expense of both the furnace shop and its allied foundry or mills. Many years ago water-cooled equipment applied to iron blast furnaces made it possible to increase greatly not only the size and production of the furnaces but also the life of the lining. It also cut down the loss from frequent repairs. The open-hearth furnace is a much later invention, especially as a commercial factor; for though it dates from the Fred Siemens patent of 1856, much more progress was made in the Bessemer process until the latter eighties and most of the development

Jan 1, 1920

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By Walter Knox, J. D. Doherty

In 1939, at the request of The Koppers Coal Co., the Koppers Company Research Department established a Stoker Coal Research Laboratory for the purpose of investigating the performance characteristics of stoker coals in typical domestic stoker installations. Fig. I is a photograph of part of the laboratory. The material in this paper deals with the performance of one coal in a single installation. Presented are details of this installation, mechanical characteristics of the stoker, and the results of a series of burning tests in which adjustments were systematically varied. Summary OF Results Mechanical Features I. A large percentage of the total power consumed by a domestic stoker is used to operate the gear case and motor (Fig. 3)- 2' The power consumption per ton goes down with an increase in rate of coal feed (Fig. 4). 3. The automatic air control in this stoker showed advantages Over manual control (Fig. 5). 4. The air velocities through the retort tuyeres were uniform around the retort, but varied between the rows of tuyere rings (Fig. 6). 5. The crushing of coal with this stoker increased the minus 1/8-in. from 11.6 per cent to 19.2 per cent. There was a notice- able segregation of coal as it came from the retort and distribution was not uniform (Fig. 7). 6. Measurement of air entering over the fire showed that with some not uncommon adjustments this air may be a high percentage of the total air supply (Fig. 8 and Table I). Operating Performance ,. The, removal of clinker was shown to give a period of poor performance characterized by a high fuel-bed resistance and a high percentage of carbon monoxide in the flue gases (Fig. 10). 2. The fuel-bed resistance was found to decrease as the fuel bed built up in a normal response to heat demand after a prolonged hold-fire (Fig. II). 3. with intermittent operation the burning rate was almost always less than the feeding rate, The wide variations were found to be greatly dependent upon the length of the On period and the length of the intervals between On periods (Fig. 12). 4. The maintenance of a low furnace draft led to less fly ash, better clinker formation, and higher efficiencies (Fig. 13). 5. The maintenance of a minimum of excess air also resulted in less fly ash, better clinker formation, and higher efficiencies (Fig. 14). Guiding Principles In planning the investigations, the following principles were adopted: Selection of Heating Equipment.—Use only standard models of stokers and furnaces representative of those widely used.

Jan 1, 1942

By J. Chipman, N. J. Grant, J. C. Fulton

This paper contains data on the distribution of silicon between liquid iron-silicon-carbon alloys saturated with respect to graphite and CaO-SiO2-Al2O3 slags under 1 atm of CO at 1600°C. The ranges of slag compositions studied were extended from the dicalcium silicate saturated liquidus composition up to silica concentrations at which Sic appeared as a stable phase. IN blast furnace operation it is not to be expected that slag and metal reach equilibrium with one another. Nevertheless, the silicon content of the metal varies with slag composition and with temperature in a manner which would be predicted from equilibrium considerations. Similarly, the distribution of sulphur between slag and metal does not attain an equilibrium state, yet the influence of slag composition is strongly analogous to its effect on the distribution equilibrium. The desulphurizing power of metallurgical slags has been shown to be highly dependent upon the FeO content of the slag. Moreover, the rate of removal of sulphur from slags is influenced by the oxygen potential of the slag-metal system. Thus it was shown by Grant, Kalling, and Chipman1 that the presence of MnO in slags which are low in FeO causes a marked slowing down of the transfer of sulphur from metal to slag. This led to the hypothesis that the slow removal of sulphur by blast furnace slags of more acid composition might be due in part to the effect of SiO2 on the oxygen potential of the system. This was verified in the work of Grant, Troili, and Chipman,' who found that the desulphurizing power of the more acid blast furnace slags could be markedly improved by an increase in the silicon content of the underlying metal. Their explanation of this improvement was that the higher silicon content of the metal decreased the rate of transfer of more silicon and, along with it, of oxygen from the slag to the metal. The slowness of the transfer of sulphur from metal to slag was the result of the slow reduction of SiO2 from slag to metal. Attempts to study the rate of sulphur removal had in the past resulted in very slow rates corresponding to the rates of silica reduction. It has become evident on the basis of these studies that further experimental studies on the rate of removal of sulphur must take these factors into consideration if there is to be a clear understanding of the rate of sulphur transfer under conditions simulating those existing in the blast furnace. It will be necessary, at least in a part of such study, to employ combinations of slag and metal in which the disturbing effect of silica reduction has been eliminated; in other words, to employ slag-metal combinations which are already in equilibrium with respect to the transfer of silicon. In preparation for such studies of desulphuriza-tion, a preliminary program of research on the distribution of silicon between slag and metal has been undertaken. This will ultimately include a comprehensive survey of the effects of temperature and slag composition on the equilibrium distribution of silicon between slag and metal. The present paper is a report on experimental methods employed and on

Jan 1, 1954

By Joseph W. Leonard, T. S. Spicer

INTRODUCTION Reasons for Thermal Drying The continuing increase in the percentage of minus %-inch coal produced as a result of the increased use of mechanical mining methods has, over the years, tended to shift considerable portions of the work of producing saleable coal to the fine coal cleaning section of the preparation plant. Because a given weight of fine coal will contain substantially greater surface area than an equivalent weight of coarse coal, it follows that, when subjected to wet cleaning processes, the fines will absorb and retain consider- ably more moisture than coarser fractions. Increased moisture pickup in the finer sizes complicates fine coal cleaning since beneficiation may not be limited to the removal of ash and sulfur but often must be expanded to include the additional step of thermal drying to remove excessive moisture. Thus, water which provides the medium for cleaning fine coal is in itself detrimental and, like ash and sulfur, reduces coal quality. Removal of surface moisture by drying is done for one or more of the following 1 reasons: (1) To avoid freezing difficulties and to facilitate handling during shipment, storage and transfer to the points of use; (2) to maintain high pulverizer capacity; (3) to reduce heat loss due to evaporation of surface moisture from the coal in the burning process, thus increasing heating efficiency; (4) to improve the quality of coal used for special purposes, such as in the production of coke, briquettes, and chemicals; (5) to decrease transportation costs; and (6) to facilitate dry coal-cleaning processes. Because benefits to coal transportation and utilization are the most common reasons for thermal drying, the following sections will examine these areas in greater detail. Benefits to Transportation Initial benefits from drying are the reduction of shipping costs from the mine to the point of utilization since more coal can be concentrated into a given weight of product when worthless moisture is removed. Non- combustible~ such as water and mineral matter in railroad shipments of coal are billed the same as coal at $3.32 per ton, according to the recent average costs. Savings of 10 to 20 dollars from drying on the shipment cost of each 50 to 60 tons of coal contained in a typical railroad car is common. Savings on coal shipments from individual mines which result from coal drying can be expressed in terms of hundreds of thousands of dollars and more each year. For example, a reduction of shipping charges of only 5 percent on one million tons per year would mean a savings of 166,000

Jan 1, 1968

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943

By William H. Spice

The year 1942 in the South Central Texas area was marked by a sharp curtailment of exploratory drilling as compared with the past several years. In the 33 counties that compose this district, 17 of which are nonproducing counties, only 51 exploratory wells were drilled during the year 1942. This compares with 118 exploratory wells drilled during 1941, or a decrease of more than 50 per cent. At the end of the year 10 active exploratory wells were drilling in this area, as against 19 being drilled at the end of 1941. Of the exploratory wells drilled, two brought in oil wells and were new field discoveries and one was a gas well extending a recently discovered shallow gas area in the western part of the district. This compares with five new oil fields, one new . gas field and two extension wells drilled in 1941. Both new field discoveries were small and in areas outside of the general trend of the main producing horizon of the district in Edwards limestone: One new field, the Imogene, in Atascosa County, is a deep Edwards limestone prospect at 7500 ft., and the other new field, the Poth, in Wilson County, is a sSEa110w Wilcox (Eocene) prospect at 4000 ft. Subsequent drilling in each field to the end of I942 has proved disappointing. There were no new discoveries along the old Balcones fault-line trend, although 35 of the exploratory wells were drilled in counties along this trend. Approximately 38 wells were drilled in or adjacent to the proven fields of the district, of which 18 were oil wells, 2 were gas wells and 17 were dry holes. The district produced 6,186,178 bbl. of oil during 1942, which was a 7 per cent decrease under production for 1941. Approximately 4,961,000 bbl. of this total production, a slight increase over 1941, was produced by the four Edwards-limestone fields, Luling, Branyon, Salt Flat and Darst Creek, and the rest of the production came from the other 42 active fields in the district. During the year, 20 new producing wells were completed and 221 wells were abandoned in the producing fields. This alarming excess rate of abandonment~ over completions will be further reflected undoubtedly by a further decreased rate of 1943 production under 1942. Two active fields in the district in which more than one producing well was completed during the year were Bee Creek and Washburn. The majority of exploratory work in the district was confined to areas along the Wilcox trend, with a certain amount in progress along the deeper Edwards limestone trend. The successful completion of sevemi wells in the Washburn field from multiple sands in the Lower Wilcor (Eocene) has stimulated exploratory work along this trend, while the completion of a small well in the Imogene field from the Edwards limestone at 7500 ft. has renewed interest in this horizon at depths greater than generally are producing in the district. New Fields ounty. ble Oil and Refining Company's No. I

Jan 1, 1943

AUGUST began with a reminder that warfare was still in progress in the world, in that the Greeks, still at war with Turkey, threatened Constantinople in spite of the small British and French forces of occupation and opened a vista of international dangers. There was in this, moreover, a recollection that religious questions in India had prevented the British from permitting a real settlement of the Turkish question, wherein the absence of Russia as a great power is missed. Civil warfare also continued in Ireland and China. Even in the military way the world is far from being at peace. Bloody fighting between the Fascisti (anti-communists) and the com-munists in Italy led to several provinces being put under martial law, but after a while these disturbances were quelled. In the latter part of the month the assassination of Michael Collins in Ireland produced a great shock. From China, however, there came rather favorable news, indicating the early reintegration of that country, which sooner or later ought to play an important part in world affairs. Economically, instead of there being any improve-ment, there grew a clearer perception of how bad things really are. Italian politics were in chaos through inability to find anyone to accept the premiership and assume the all but hopeless task of averting national bankruptcy. The French, too, began to see their own position in true colors, and especially to see how in reconstruction they had incurred debts on the strength of what they hoped to collect from Germany, with at last the understanding that the Germans could not pay and that France herself was thereby put in a desper-ate economic position. As for the Germans, them-selves their Reichsbank defaulted on ordinary bills early in August. As the month wore on the value of marks fell more and more and at the end it appeared that Germany was on the verge of economic collapse. On Aug. 7, another international conference (with America again absent) was assembled in London, this being the thirteenth since the war, and there was a general feeling that it would be the last. The prime question was what is to be done about the German reparations, but underlying was the whole subject of the entente. The conference opened like a meeting of importunate creditors, doubtful whether the debtor had any tangible assets. On Aug. 14 this conference broke up without coming to any useful conclusion. Indeed, the acrimony among the premiers was so sharp that even the entente between Great Britain and France was endangered. The international situation was saved only by the Reparations Commission excusing the Germans from the payment of 50,000,000 gold marks that come due on Aug. 15 But although the entente was nominally preserved there is no longer any illusion about the interests of Great Britain and France being different and that henceforth they will play their own hands. The London conference was really an effort to maintain the partnership, and it failed.

Jan 9, 1922

By V. S. Swaminathan

This year, Great Britain is looking back over a century to August 14, 1850, the day when the first "Act for the Inspection of Coal Mines" was passed in that country, an act which signaled the end of over two hundred years of hitherto uncontrolled and dangerous mining practices. It was back in the time of Queen Elizabeth that . thousands of pounds were invested in mining, particularly coal mining in England and Scot- land. By 1640 there were collieries producing 10,000 to 25,000 tons of coal per year. In the seventeenth century the Tyne district coal industry was organized into powerful partnerships, and coal took an even larger part in industry, as a source of power and as fuel for the iron industry. In the early 19th century a "phenomenal, almost devastating expansion" characterized Britain's coal industry, and it was sparked by a 111 pct in- crease in the population of England and Wales in the first half of the century. Coal production for those 50 years increased 470 pct and pig iron production was up 946 pct for the period 1801-51.

Jan 1, 1950

By Albert Williams

A large proportion of the work performed in wet-crushing silver mills is devoted to the handling and re-handling of pulp between the battery and the pans. There seems to be no generally applicable substitute for the settling-tanks, and in the present system of constructing mills the tanks involve an amount of labor which may be regarded as disproportionate and unnecessary, in view of the automatic improvements which have been introduced in other directions. This diffculty has been met, however, by Boss's continuous process, in which the pulp flows directly from the mortars to the first of a series of constantly working overflow-pans. This method has been adopted at the Noonday mill, Bodie, California; the Harshaw, Arizona; the Sierra Grande, New Mexico ; and the Prietas, Sonora. The continuous process, while giving excellent results with special ores, and under peculiar local conditions (such as a deficiency in water supply), is not, I believe, claimed to be available for all raw-amalgamating mills, notwithstanding its well-merited popularity for certain work. Some trouble has been experienced from the tendency to concentration in the pans, though this can be avoided by skilful manipulation. It has also the disadvantage inherent in combinations of distinct operations ; it requires a very nice adjustment of the water supply to obtain full battery efficiency without running the pans too thin, though the latter defect is partially compensated for by the gradual thickening of the pulp as it proceeds through the series of pans. The objection is similar to that which holds in a parallel duplex process, that of combining roasting and smelting in a single furnace, where each operation is injuriously affected by the necessity of fitting it in with another and entirely different one.

Jan 1, 1883

By A. B. Parsons

PUBLICATION of this little volume is a luxury that the Institute itself could scarcely afford. In truth, no engineer nor geologist, no assayer nor metallurgist would be likely to enhance his knowledge, improve his technique, or cut his own operating costs by reading this excellent translation of two booklets first published circa A.D. 1520. It is doubtful if the present enterprise would, in a practical or tangible way, "promote the arts and sciences connected with the economic production of the useful minerals and metals." And such, is the prescribed purpose for which the funds of the Institute should be spent. Fortunately for the Institute, the Seeley W. Mudd Memorial Fund is not so circumscribed; and the Fund Committee enjoys, greater liberty of action. The sponsorship by the Mudd Fund in 1942 of the publication of The Pirotechnia of Vannoccio Biringuccio, as translated by Dr. Smith and Mrs. Gnudi, was an innovation-indeed something of an experiment. Not only was the content of the volume significant mainly for its "cultural" and "scholarly" attributes; -but the format, an outstanding example of the fascinating art of bookmaking, bore no resemblance to the ordinary technical book. The Committee, frankly, was surprised at the enthusiastic reception accorded the volume. When a second edition was required, the Committee became convinced that the publication of material of this type, particularly if printed and bound in attractive form, was an appropriate avenue for utilizing a moderate proportion of the monies available from the Fund. The Bergbüchlein and the Probierbüchlein antedate by some years the first publication of De la Pirotechnia and of De re Metallica; but Georgius Agricola, the author of the latter work, made good use of the material in the earlier volumes. As pointed out in the Introduction, both

Jan 1, 1949