Search Documents

By Alfred E. Hunt

In a paper written for the Boston meeting of February, 1888 (Trans., xvi., 693), on "Some Recent Improvements in OpenHearth Steel Practice," the writer described the reducing agent used by the Carbon Iron Company as "a peculiar graphite from Cranston, near Providence, R. I." Upon an application pending at that time, a patent has since been issued as number 259,795, to Mr. Matthew Graff, for the use of solid carbonaceous matter in the form of coke, charcoal, gas carbon, bituminous or anthracite coal, ground to the size of coarse sand and then coated with a mash of lime, magnesia, clay, or other material of a like character, as an agent to reduce metallic oxides. An amount of this prepared carbonaceous matter equal to from 25 to 30 per cent. of the weight of the ore treated is required to perform the complete reduction. The idea is that the carbonaceous matter is protected against rapid combustion by a suitable coating of some inert material, so that, in effect, its action as a reducing agent will be similar to that of the Cranston graphite previously used, allowing the solid carbon to remain without combustion in intimate mixture with the iron oxide at a temperature sufficiently high to reduce the ore and in some cases to melt the matrix in which the iron is held. In the present practice of the Carbon Iron Company, the use of graphite, except for the formation of bottoms of the reverberatory furnaces in which the reduction is performed, has been entirely abandoned, and " retarded coke," as it is called at the works, has taken its place. Five hundred and fifty pounds of Connellsville coke is ground in a pan to 16-mesh fineness, or is taken in the form of ordinary coke-dust, and made into a hollow basin on the mixingfloor ; and seven bucketfuls of a wash composed of equal parts of lime and fire-clay, mixed in water to the consistency of thin cream,

Jan 1, 1889

By Earl A. Trager

The broad picture of world petroleum production at the present time is one of an excessive supply. In any consideration of corrective measures to be applied in the future, it will be necessary to include all the producing areas of the entire world. To illustrate, United States production during 1931 was 48 million barrels1 less than 1930, whereas world production exclusive of the United States increased, owing principally to increases in Russia, Rumania and Persia. Domestic Peoduction Let us first consider the domestic production situation. Due to the fact that United States production was maintained below current demand, about 40 million barrels of oil were withdrawn from storage during 1931. Consumption increased about 1.5 per cent over 1930, which is less than the recent annual rate of increase of 8 to 11 per cent. If the machinery to prevent waste in the petroleum industry operative for more than a year will continue during the coming year and drilling is held to the 1931 level, there will be a decided improvement in the domestic situation by the close of 1932. This will be due in large measure to the drastic reduction in exploratory work and drilling which has been in effect for more than a year. Looking ahead for two or more years, probably there will be a shortage of domestic production in relation to domestic demand, unless there are discovered several large pools comparable to Oklahoma City or East Texas. Were the United States isolated, our problems in so far as petroleum production is concerned might be considered well along the road to recovery. To maintain this perspective will require the cooperation of foreign producers in the future, or protection of United Statcs markets from foreign invasion. Let us review briefly the present situation in the United States. East Texas has been the most important factor during 1931. The large initial production of individual wells and the rapid rate of drilling

Jan 1, 1932

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen's regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By S. N. Singh, M. C. Flemings

Results are presented of a study on the combined influences of ingot dendrite am spacing and thermo-mechanical treatments on the fracture behavior and mechanical properties of high purity 7075 aluminum alloy. The most important single variable influencing mechanical properties was found to be undissolved alloy second Phase (microsegregation inherited from the original ingot). Ultimate and yield strengths were found to increase linearly with decreasing amount of alloy second phase while ductility increased markedly. At low amounts of second phase, transverse properties were approximately equal to longitudinal properties. In tensile testing, microcracks and holes were invariably found to originate in or around second phase particles. Fracture occurred both by propagation of cracks and coalescence of holes, depending on the distribution and amount of second phase. IN most commercial wrought alloys, second phase particles are present that are inherited from the original cast ingot. These include, for example, non-equilibrium alloy second phases such as CuAl2 and impurity second phases such as FeA13 and Cr2A1, in aluminum alloys. A previous paper1 has dealt with the morphology of these second phases in cast and wrought aluminum 7075 alloy, and with their behavior during various thermomechanical treatments. In this paper we discuss the influence of the particles on mechanical properties and fracture behavior of the alloy. Previous experimental work indicating a direct and major effect of second phase particles on mechanical properties (especially on ductility) includes the work of Edelson and Baldwin on pure copper.' Also relevant are the many studies demonstrating the important effect of nonmetallic inclusions on the fracture of. steel.3'4 Work on aluminum includes that of Antes, Lipson, and Rosenthal5 who showed that a dramatic improvement in ductility of wrought aluminum alloys of the 7000 series is achieved by eliminating second phases. It now seems well established that included second phases play a dominant role in controlling ductility (as measured, for example, by reduction in area in a tensile test) of a variety of materials. There is, therefore, considerable current interest in the mechanisms by which second phase particles affect ductile fracture. Experiments done by various workers have shown that second phase particles or discontinuities in the microstructure are potential sites for nuclea-tion of microcracks and of holes,6-l3 which then grow and cause premature fracture and the loss of ductility. Theoretical attempts have been made to explain the observed phenomena; most are able to explain observations qualitatively, but lack quantitative agreement. Much experimental work needs to be done to aid extension of theoretical models. A recent review article by Rosenfield summarizes work in this general area.14 PROCEDURE Material used in the previously described study on solution kinetics of cast and wrought 7075 alloy1 was also used in this study. Procedures for ingot casting, solution treating, and working were described in detail in that paper. Test bars were obtained for material of 76 initial dendrite arm spacing (11/2 in. from the ingot base) and 95 µ initial dendrite arm spacing (51/2 in. from the ingot base) for the following thermomechanical treatments (solution temperature 860°F; reduction by cold rolling). a) Solution treated 12 hr, reduced 2/1, 4/1, and 16/1. b) Solution treated 12 hr, reduced 16/1, solution treated approximately 5 hr after reduction. c) Same as a) except solution treated 24 hr prior to reduction. d) Same as b) except solution treated 24 hr prior to reduction. e) Same as d) except solution treated 20 hr after reduction. Test bars were taken both longitudinally and transverse to the rolling direction. Transverse properties are in the long transverse direction; since the final product was sheet (0.030 in. thick), properties in the short transverse direction could not be obtained. Test bars were flat specimens, of gage cross section1/-| in. by 0.030 in. and 1/2 in. gage length. After machining the test bars, they were given an additional 1/2 hr solution treatment of 860°F and aged 24 hr at 250°F. Three bars were tested for each location and thermomechanical treatment, after rejection of mechanically flawed bars. The average results of these three bars are reported. Elongation was measured using a $ in. extensometer and reduction in area was determined using a profilometer to measure the area after fracture. INFLUENCE OF THERMOMECHANICAL TREATMENTS AND SECOND PHASE ON MECHANICAL PROPERTIES Results of mechanical testing are presented in Figs. 1 to 4 and in tabular form in the Appendix. A general conclusion from results obtained is that details of the thermomechanical treatments studied were important only insofar as they influenced the amount of residual second phase. Figs. 1 and 4 show the longitudinal properties obtained (regardless of thermomechanical

Jan 1, 1970

By A. H. Daane, J. F. Haefling

The limits of miscibility in some of the uranium rare-earth alloy systems have been determined in the temperature range 1000°to 1250°C. The solubilities of lanthanum and cerium in uranium are greater than those of the remaining rare earths by a factor of more than two. The solubility of uranium is greater in cerium, braseodymium, and neodymium than in the other rare-earth metals studied. The values found in this study are in qualitative agreement with those which might be expected if the solubility rules of Hildebrand and Scott are applicable. AS interest in nuclear reactors intensifies, many new types of fuels are being suggested in attempts to improve the economics of some of the proposed reactor schemes. To remove some of the difficulties inherent in the use of solid-fuel elements and their reprocessing, many types of liquid-metal reactors have been suggested. One of the more attractive features of several of these reactor concepts is that they include a continuous or semicontinuous process for the extraction of fission products and "bred" fissionable materials from the fuel, utilizing immiscible metal extractants. This would enable a much higher burn-up of fissionable material to be achieved and would present a very attractive economic picture. Several studies have been reported on equilibrium systems in which there exists a high degree of immiscibility between uranium and another metal that might be used as an extractant in such a processing scheme.' Two of these systems in which a high degree of immiscibility exists are those of uranium with the two rare-earth metals, lanthanum, and cerium. Since the rare earths constitute a significant fraction of the fission products, their removal is of prime importance. It is reasonable to believe that this might be accomplished by equilibrating a rare-earth phase with the contaminated uranium fuel in the liquid state. In order to make a more complete study of those systems which would be of interest either as extractants in a liquid-liquid extraction process, or as fission products formed in the fuel, the alloy systems of uranium with lanthanum, cerium, praseodymium, neodymium, and samarium were studied in some detail in the temperature range 1000" to 1250°C; less detailed studies were made with the other rare earths. In addition to being of value to the reactor program, the data obtained in this study should be of help in making a study of the role played by the electronic structures of metals in determining the nature of metallic solutions. The unique electronic structures of the rare-earth elements make them particularly interesting in this respect. EXPERIMENTAL The usual procedure for a solubility determination was to seal equal volumes of uranium and the particular rare earth in a tantalum crucible under an atmosphere of helium; this crucible was then sealed in a stainless steel jacket in an atmosphere of helium. These samples were equilibrated by repeated inverting of the crucibles in a furnace for 15 min at the desired temperature, left in an upright position for 15 min to permit separation of the two phases, and then quenched under a stream of water. In some runs the temperature of the furnace was held 50' to 100°C above the desired quenching temperature while inverting in order to insure good mixing. However, it was found that above 1200°C the crucibles were subject to failure and for these runs the furnace temperature was not raised above the desired quenching temperature. A small amount of tantalum was dissolved in the uranium and the rare earths in these runs, a maximum of 3 wt pct in the uranium phase at 1250°C and up to 1 wt pct in the rare-earth phase at this temperature. On cooling, the major portion of this tantalum precipitated as primary tantalum crystals. Any residual tantalum would probably have a negligible effect on the mutual solubility of uranium and the rare earths in each other. Samples for analysis were cut from each phase with an abrasive cutting wheel; the region near the interface between the two metals was carefully avoided. In the case of the rare earths with melting points above 1250°C no solubility data were taken on the rare-earth phase since this phase could not have achieved equilibrium in a reasonable length of time. (For the same reason no data were taken on the uranium phase below its melting point of 1132°C.) Equilibrium appeared to have been reached in the uranium phase in these cases although the rare-earth phase had not melted. To verify this, samples were melted together in an arc furnace similar to that described by Kroll.2 These samples were sub-

Jan 1, 1960

By P. K. Leung, S. R. Allada, P. M. Dranchuk, D. Quon

The alternating direction explicit procedure (ADEP) makes use of the boundary conditions to reduce multi-dimensional problems to a series of one-dimensional problems. The method, previously applied to reservoirs containing only an under-saturated oil, has now been extended to cover the case of natural gas reservoirs. l his involves solving a non-linear partial differential equation, application of the procedure is straightforward and no calcuIational problems were encountered. INTRODUCTION There has been a growing interest in formulating mathematical models of petroleum and natural gas reservoirs — models which permit the engineer to examine and evaluate the physical and economic consequences of various alternative production policies. The tremendous reduction in the cost of solving such models in recent years has made possible their use as an almost routine management tool. This reduction is the result not only of improved computer hardware but also of the development of more efficient mathematical techniques. The present paper is concerned with the application of a recently proposed numerical method (ADEP) to two-dimensional gas reservoirs. STATEMENT OF THE PROBLEM Given a two-dimensional Region R, bounded by a closed Curve C (Fig. 1) such that the behavior on Curve C is known, the differential mass balance for each fluid phase in R, neglecting gravitational effects and assuming Darcy's law for fluid transport, can be written as:

Jan 1, 1967

By M. E. Lombardi

THE Coalinga oil field is located on the west side of the San Joaquin Valley, California. The structure is in general a monocline, the edges of the oil horizon resting on the foot hills and dipping gently toward the east. One prominent anticline occurs plunging southeast. The earlier drilling was done in the foot hills comparatively near the outcrop and the wells were shallow. The sands were followed eastward and, in the case of the anticline, along the plunge, the wells becoming deeper and deeper until the depth of 4,000 ft. was reached and passed. There is nothing to show that the oil will not be found in quantity at still greater depth. In fact, some of the best producers have tapped the sand at close to 4,000 ft. The recovery of oil still farther to the east, and therefore at greater depth, seems to be mainly a question of drilling. In this territory the formations drilled through are chiefly sands and shales; they will not "stand up" in an open drilling hole; the casing has to be carried close to the bit, and it is always difficult to keep the casing free for any considerable distance. Ability to carry casing of comparatively large diameter without conductor pipes for distances of 2,000 or 3,000 ft. or over is desirable in such territory chiefly for two reasons. It makes it possible to enter the oil sand with a pipe of ample diameter; it eliminates one or more expensive strings of casing which act only as conductors for the water string, and furthermore, in territory where waters are encountered which corrode steel rapidly, it makes possible the construction of a rust- and alkali-resisting water string. It is always desirable to shut off top waters, which may lie within 100 ft. or less of the oil sand, with 10-in. pipe. Where the depth is so great that a practical weight of 10-in. pipe will not withstand the probable collapsing pressures, 8 ¼ in. at least is desirable. About the limit of rotary drilling to date in California seems to be the setting of the 10-in. string at 3,200 ft., although the rapid advance in rotary work during the past year seems to indicate that this depth may soon be increased. It is my purpose now, however, to treat only of cable-tool drilling.

Jan 2, 1915

By Valentin R. Garfias, C. O. Isakson

The production of oil in Mexico during 1929 was approximately 45,000,000 bbl., or 5,000,000 bbl. less than in 1928. The production of the fields near Tampico showed a decline of over 10,000,000 bbl. for both the light and heavy crudes, which was partly offset by an increase of over 5,000,000 bbl. in the production of the fields in the Isthmus of Tehuantepec. During 1929 the retrenchment policy followed by practically all the companies was continued and no material improvement should be expected until the unsatisfactory conditions that brought about this situation are remedied. A new administration has just assumed control in Mexico; it should remain in power for 6 years, and the progress of the oil industry during that time will depend primarily on the policy pursued by the new government with respect to oil development. Development During 1929, there were drilled 214 wells as compared with 371 in 1928 and 583 in 1927. The percentage of producers in 1929 was 47.2 as against 34 per cent. in 1928. The new wells did not show water as quickly as in 1928, particularly in the Cacalilao field, where the greatest number of producers was brought in, their average initial daily production being 380 bbl. The flush daily production per well in the Southern fields was 1730 bbl., while the wells in the Isthmus of Tehuantepec came in with an average of 770 bbl. Development is summarized in Table 1. In the Southern fields 63 wells were drilled in 1929, of which 23 were producers, the best being drilled in Paso Real. This development tends to show that the southern extension of Dos Bocas-Alamo fault from Alamo to San Isidro terminates at San Isidro. The two wildcat wells completed in 1929, one in Magiscatzin and the other in Xicotencatl, were failures, and at the end of the year there were eight wildcat wells drilling and material was being hauled for two more.

Jan 1, 1930

By Paul F. Sikora, John W. Weeton, Philip A. Clarkin

Effects of variations in carbon content and micro-structure on the stress-rupture properties of a liquid-phase-sirztered, Izeut-resistunt alloy were studied. Using the powder rnetallurgy technique, specimens could be produced having stress-rupture profierties equivalent to or better than those of the alloy in wrought form. In addition, sintered specimens were easily hot worked even when carbon contents were as high as I pct. Correlations between stress-rupture properties and micro structure were obtained in some cases. IT is well known that many alloys used in high-temperature service are quite complex both from the standpoint of chemical composition and microstruc-ture. During the development of these alloys their complexity has in some cases led to treatment schedules which, while practical, often do not fully utilize available alloying elements. For example, in some alloys, massive carbides that form during ingot practice may never be dissolved by reasonable solution treatments and therefore are unavailable for subsequent precipitation hardening, Ref. 1. This investigation was undertaken to determine whether the powder metallurgy method of consolidation might provide distinct advantages over the conventional melting method. First, segregation of alloying elements might be eliminated or reduced and thus a more efficient use of these elements obtained. Second, the structures produced in powder specimens might differ considerably from those normally seen in castings, which would perhaps result in better response to subsequent mechanical or thermal treatments. If these results could be achieved, it was felt that both forgeability and stress-rupture properties might be improved. The alloy used in this investigation was S-816 produced by powder metallurgy methods. The influence of carbon content over the range of 0.1 to 1.0 wt pct was studied for the alloy in the as-sintered condition and after three additional treatments involving heat treatment, hot swaging, and combinations thereof. EXPERIMENTAL Standard S-816 has the composition shown in Table I. It is a cobalt-base alloy having a nominal carbon content of 0.4 pct and is classified as a precipitation-hardening alloy. This alloy was chosen because it is representative of a class of heat-resistant alloys and because adequate information was available concerning its response to various treatments and its subsequent properties. For this study, -100 mesh alloy powder having essentially the same composition as shown in Table I but without the 0.4 pct C was used. Desired carbon variations, achieved by wet mixing the alloy powder with graphite, ranged from 0.1 to 1.0 wt pct. Specimens were hydrostatically pressed and then sintered in vacuum by slowly heating until incipient melting was observed. Sintering this way gave a liquid phase in the interstices of the powder particles and achieved reasonably high densities. The average density of as-sintered specimens was about 95 pct of wrought alloy density. In order to obtain various microstructures, some specimens were heat treated (solution treated for 24 hr at 2150°F, water quenched; aged 16 hr at 1400°F, air cooled); others were hot swaged at 2150 o F (50 pct reduction in area), while still others were hot swaged (50 pct reduction in area) and then given the above heat treatment. During hot swaging it was observed that forgeability was quite good even when specimens contained as much as 1.0 pct C. Specimens were evaluated by stress-rupture test-

Jan 1, 1962

By J. F. Gormley

Drill pipe, and the connections used to join the pipe together, have had a long history of development and improvement. With the growing use of high tensile-strength pipe, the rotary shouldered connections used to join the lengths of drill pipe have become more critical. Fatigue-type failures of rotary-shouldered connections, or tool joints, have become a cause of much conern to operators and manufacturers. Most fatigue tests on tool joints have been made on the basis of bending moment applied vs number of cycles, rather than on the basis of stress vs cycles. A desire to learn more about the nature of stress in a tool joint due to bending caused a rather intensive experimental study to determine what actually happens to cause fatigue failure. It was known that a tool joint with insufficient make-up torque was subject to early fatigue failure. Therefore, the establishment of the relationship between make-up torque and allowable bending moment would enable a testing engineer to better correlate the results of various tests. The problem of calculating the stress in a tool joint due to an applied bending moment was complicated by: the effect of unknown stress concentrations; the applicability of the well known formula S = Mc/I; and the question of whether to use the combined cross section of the pin and box in calculating the moment of inertia I. TEST EQUIPMENT The test equipment consisted of the following. 1. A lathe modified to act as a fatigue machine for full-size tool joint or drill-collar specimens. 2. An adapter plate bolted to the headstock of the lathe and into which a short adapter was screwed. 3. Tool-joint pins on sections of drill collars bucked into the adapter. 4. A hydraulic load cylinder which rested on the bed of the lathe and applied bending moments to the joints. 5. Paper-backed strain gauges (FAP-12-12, 1/8-in. gauge length and A-5-1, 1/2-in. gauge length). 6. Eastman 910 contact cement for bonding gauges to joint and Epoxylite 222 waterproofing. 7. A 12-position switchbox, SR-4 bridge balancing unit connected to an SR-4 strain indicator to read the gauge output. 8. A four-channel Sanborn recorder, Model 150, was used as the readout instrument for part of the testing. The fatigue machine was well suited as a loading device. Because of the long lever arm available, the change of moment with distance was small; consequently, the vertical shear stress was small, less than 300 psi. Some difficulty was experienced with the hydraulic load cylinder at high bending moments due to leakage. The strain gauge equipment was simple and quite reliable. A 41/2-in. extra hole (E. H.) joint with "as machined" threads and shoulders and a 2 7/8-in. internal flush (I. F.) joint with copper-plated threads and shoulders were selected for testing because of their common usage in the field. In addition, the 4 1/2-in. E. H. was suitable because it had an inside diameter large enough to permit the insertion and accurate positioning of strain gauges without using special jigs, while the 2 7/8-in. I. F. joint required much lower bending loads to cause separation of the shoulders of the joint when made up to the recommended torque. The joints were made to standard API specifications, except for very small bevels on the box and pin shoulders and cylindrical stress-relief grooves added to the pins. Larger bevels would have

By B. L. Sackett

The converting of lead matte is not a general practice at lead smelters, therefore a description of the methods used and developments made during the past 20 years in converting both lead and copper matte at the Tooele plant of the International Smelting Co. in Utah may be of interest. The Tooele converting plant consists of five electrically operated stands in which are used 96 by 150-in. horizontal, barrel-type converters each of about 10 tons capacity. The main converter building is served by a 60-ton electric traveling crane and the casting shed by a 30-ton crane. Copper matte is tapped from near-by reverberatory furnaces into launders that deliver into 8-ton ladles on the converter floor. Lead matte is brought from the blast furnaces, about li mile away, in 5-ton ladles mounted on trucks, hauled by electric locomotives. As the Tooele copper plant has never been a producer of much copper, and has been Irregular in its operation, the original converting plant with its small converters has been adcquate, although decidedly out of step with large, modern plants. Tonnage figures in this paper are for comparison with each other only, as they are not at all in line with prevailing tonnages at larger plants today. The reasons for the changes made in converting practice at Tooele, as well as the improvements in the results obtained as these changes were perfected, are given in the following pages. Lead-matte Converting, 1914 to 1927 In 1914, Oscar M. Kuchs wrote a paper for the Transactions,' describing in detail the lead-matte converting methods at Tooele up to that time. The method perfected only a few months before Mr. Kuchs' paper was written consisted, briefly, of blowing the lead matte alone, without the addition of siliceous fluxing ores, to a point where the lead and zinc were largely eliminated by volatilization. During this period

Jan 1, 1934

By Henry Louis

The present paper comprises two parts, which have but little con nection with each other. The first is practically a continuation of the investigation on the specific gravity of gold liberated by means of acids from its alloys, on which subject I had the honor of presenting a brief note to the Institute in 1893 (Trans., xxii., 117); the second describes a series of experiments on the behavior of amorphous gold under the action of heat. By the kindness of Prof. W. C. Roberts-Austen, C.B., F.R.S., chemist to the Royal Mint, I have been permitted to conduct these experiments in the mint assay-office, all the splendid resources of which institution were freely placed at my disposal. I desire at the outset to express my obligations to Prof. Roberts-Austen and to all the staff of the mint assay-office for their kind assistance at all stages of my experiments. I.—The Specific Gravity of Gold in Alloys. In the note already referred to, I published my discovery that the gold left on dissolving out the silver from an alloy of gold and silver (which I shall here term " residual amorphous gold ") has a higher specific gravity than ordinary molten gold. I also pointed out that I had worked on very small quantities of material and with balances and weights on the accuracy of which I could not implicitly rely, and that in so far my numerical data were inconclusive, although I had but little doubt of the correctness of the broad fact. The experiments now recorded were made under the most advantageous circumstances and with various refinements. Particularly, I found that the ordinary form of specific-gravity bottle was responsible for several small sources of error; and I accordingly designed an improved form (Journal of the Society of Chemical Industry, April 30,1894, vol. xiii., p. 322), which I used for this work. The

Jan 1, 1895

By M. J. Coolbaugh

There is a need for concepts and techniques developed specifically for blasting in areas where the rock is loose or highly fractured. Common practice has been to use techniques developed in hard homogeneous rock and reduce the amount and strength of explosive. However, this rule cannot cope with all of the special characteristics of highly fractured rock and has not adequately taken care of the problems of overbreak, gouging, and wall damage. The main problems encountered when blasting in highly fractured rock are controlling the amount of rock broken, minimizing the damage done to the remaining wall material, and adapting blasting methods to rapidly fluctuating ground conditions. In addition, because it frequently needs timber support right into the blasting area, there is also the problem of how not to shoot out the timber when heavy loading is needed in order to offset a loss of impact caused by deflection of the detonation wave off the numerous rock interfaces, and by the absorption of the wave by resilient clay particles. Another consideration is the fact that less attention needs to be directed toward producing satisfactory fragmentation of the broken rock. Those blasting methods designed for breaking hard rock into manageable segments are, as a rule, not needed in highly fractured rock which will usually break along its own numerous fracture lines.

Jan 8, 1965

By George H. Deike

UNDERGRADUATE interest in coal mining engineering has dropped to an alarmingly low level. Most companies having co-operative scholarship programs have been forced to abandon them for the duration.

Jan 1, 1944

By Glenn A. Keep

THIS paper is not an announcement of the successful conclusion of the Cerro de Pasco Copper Corporation's pacos-pyrite problems, but merely a description of the commercial-scale, intermittent-roasting operations conducted by the writer, J. H. Lucas and others of the staff. It was prepared by request, for presentation at the February meeting of the Institute. The results obtained in Peru confirm the 1-ton-a-day experiments completed about three years ago at Kearny, N. J. by C. C. Gordon and Mr. Lucas, where it was first demonstrated that a mixture of about 80 per cent. pacos ore with 10 per cent. pyrite ore and 10 per cent. salt could be roasted intermittently in a small 1-ton-a-day Holt-Dern furnace without extraneous fuel, producing porous calcine that could be leached rapidly. Mr. Keep and his staff, by successfully introducing improvements in the construction of the commercial furnace and in their handling of material, have established beyond doubt a low cost for roasting. The other steps in the process of treating pacos and pyrite ores have not as yet been demonstrated as sufficiently conclusive to warrant their acceptance for a permanent plant. Cerro de Pasco Ores The ores of the Cerro de Pasco Copper Corpn. at Cerro de Pasco, Peru, are situated at an altitude of 14,000 ft. The town and mines are served by the Cerro de Pasco Railroad, which operates between Cerro de Pasco and Oroya, the site of the company's copper and lead smelters. Table 1.—Average Analysis of Cerro de Pasco Ores Pacos Ore Pykite Ore Silver, oz............................................... 10.3 12.0 Gold, oz................................................ 0.007 0.01 Lead, per cent........................................... 1.7 1.8 Copper, per cent......................................... 0.19 0.27 Zinc, per. cent........................................... 1.4 1.02 Iron, per cent........................................... 13.4 34.45 Silica, percent.......................................... 61.8 24.5 Alumina, per cent....................................... 2.5 0.62 Lime, per cent........................................... 1.5 0.20 Manganese, per cent..................................... 0.42 0.09 Sulfur, per cent,.......................................... 1.1 34.2

Jan 1, 1929

By C. D. Hunter, I. B. Browning, N. W. Shiarella

During the year 1936 improvement in the oil industry in Kentucky continued at about the same rate as shown by that of the year 1935 over the year 1934. The development of several new pools in western Kentucky and the increase in the application of repressuring methods to the old fields of eastern and to a lesser extent of western Kentucky increased the total production to 5,481,227 bbl., as compared to 5,175,054 produced in 1935. The principle sources of this increased production are the Livermore field and the new Bates Knob field in McLean County, in western Kentucky, and the result of repressuring operations in the " Corniferous" pools of Lee, Powell, Wolfe, Morgan and Estill Counties and the "Weir" sand (of Mississippian age) fields of Magoffin, Lawrence and Johnson Counties in northeastern Kentucky. The last named fields have a producing sand especially adaptable to these methods. Drilling No new fields were opened in eastern Kentucky during the year. All new drilling was codned to pressure wells and new oil wells to complete patterns around the intake wells. Owing to the relatively low "initial" or flush production of the wells in this section—even though the ultimate recovery per acre is as large—higher prices for crude will have to prevail before extensive search for new fields is begun; as in northwestern Kentucky, where active exploratory work has been carried on as in the several preceding years, resulting in numerous new and prolific, although comparatively small fields. In this section approximately 500 new oil wells drilled in the Owensboro field, embracing several pools in Ohio, Hancock, Daviess, McLean, Henderson, Webster and Nuhlenberg Counties in the northwestern part of the state. The total oil production for this field during 1936 exceeded by many thousand barrels the 2,821,722 bbl. produced in 1935. In these fields the producing sands range from the middle Missis-

Jan 1, 1937

By Robert W. Hunt

PeRhaps of all the scientific economic questions which have been claiming the attention of capitalists, metallurgists, manufacturers, directors of public utilities, and the general public of America, during the last few years, none have been of more importance than the one relating to the wear and safety of steel rails. The discovery of the Bessemer process made possible modern railway development. In that growth, as has generally happened in all progressive movemeuts, all its departments have not remained equally balanced. Iron rails permitted the construction of roadways for the passage of power-driven vehicles. In time the speed and weight of such carriages proved too much for the wearing-qualities of the rails, and the limit of railway capacity seemed to have been reached. Bessemer made his invention, which was soon perfected and developed, especially as related to steel rails, and thereby increased the limit of capacity, and vastly greater railway progress was made pgssible. The Siemens-Martin open-hearth process followed, and was later supplemented by the Thomas-Q-ilchrist basic improvement. For a time the Bessemer steel rails of commerce were more than equal to all that was asked of them, but this did not long continue, as evidenced by the records in our Tansactions. Revolutionary changes occurred in the industrial world, and in no part of it more than in steel-rail manufacture. Great and powerful commercial combinations were made, whose financial resources made possible the supplanting of the then most efficient blast-furnaces, steel-works, and mills, by others of theretofore unimagined capacity. Old traditions and practices of steel-making were wiped away, and, in too many cases, output was apparently the chief aim, with the result that much dissatisfaction with the wear and safety of rails was felt by railway officials, and the general public was concerned as to its safety when traveling. The climatic conditions of the winter

Jan 1, 1913

By AIME AIME

IF the observation of our British friends is true that Americans put new records in bigness above everything else then the 150th meeting of the Institute was not the grand success it seemed to be. Just why the attendance slumped a little this year is anyone's guess, but the favourite explanation seemed to be that half the country is planning to come to the New York World's Fair this summer and that two trips from the hinterland to the me- tropolis, with another to San Francisco of course, can hardly be justified with the present condition of the stock market and the prices of the products of our mines. Certainly, some were pre- vented from coming too by the epidemic of respiratory afflictions that was rampant in February. Unfortunately. several succumbed after they had reached New York.

Jan 1, 1939

By S. W. Churchill

A digital computer was used to obtain an exact numerical solution for the transient behavior of the insulation and earth adjacent to an isothermal, submerged flat surface for a single set of parametric values. Comparison of the computed results with analytical solutions for limiting conditions revealed that a complete and general solution for all parametric values could be constructed from these limiting solutions. Complete and general solutions for insulated spheres and cylinders can also be constructed from limiting solutions. The procedure is illustrated in part for an insulated spherical tank. The heat flow was found to fall rapidly to a pseudo-steady state; after some time, it then decreased slowly to zero for a flat plate and cylinder, and to a low steady-state rate for a sphere. The accumulative heat flow during the initial falling-rate period may be a significant fraction of the heat flow during the entire first year. INTRODUCTION Underground storage of liquefied natural gas and liquefied petroleum gas has received considerable recent attention. The rate of heat flow from the earth to the storage cavity and the resulting temperature field in the earth are important factors in the technical and economic evaluation of such storage facilities. The objective of this paper is to indicate how complete solutions can be developed for the transient flux and temperature field for various geometrical configurations. The representative properties and dimensions, and the resulting parameters utilized in the illustrative results, are indicated in Table 1. The results presented herein are for dry earth. The effect of the latent heat of solidification of water in the soiI will be described in a subsequent paper. The temperature field in the insulation and earth is determined by energy balances, boundary conditions and initial conditions. The physical problem can be described mathematically with virtually no idealizations insofar as physical properties are known. It appears possible to solve the equations by numerical integration on a high-speed digital computer for any geometrical configuration and conditions. For complex situations, however, the computations are expensive and the results are highly specific. Analytical solutions have been developed for a few simple but important geometrical configurations and conditions, including one-dimensional heat transfer from (or to) earth at an initially uniform temperature to (or from) flat plates, spheres and circular cylinders. The solution for an insulated flat plate has also been derived but is in the form of a slowly converging series involving taklated functions. It was planned to use a computing machine to evaluate this series for a number of representative conditions. However, upon examination of the results of preliminary computations it was discovered that a complete, general and accurate solution could be developed by interpolation between several much simpler solutions for limiting conditions. This technique then was used to develop a a complete solution for an insulated sphere. The equations presented herein are derived in Carslaw and Jaegerl and other books on applied mathematics, or they are simple extensions of these previous results. Hence, all derivations are omitted. Emphasis is instead placed on the results and their

By W. P. Blake

THIS furnace is designed especially for the oxidation of sulphur or arsenic in pyritic ores, but may be used for all oxidizing or desulphurizing operations, and for calcining, roasting and chloridizing ores, or for drying ores in large quantities preparatory to treatment by magnetic separators or otherwise. It is of the tabular, revolving type, with automatic feed and delivery, and is a modification of the Cornish calcining furnace, designed by Brunton, from which it differs, however, not only in construction, but in two or more radical features, for which novelty is claimed and patents have been applied for. The principal of these novelties are: 1. A series of concentric terraced floors, one above another. 2. The introduction of superheated air upon the charge without contact with the fuel. In the furnace which I have had in operation for more than a

Jan 1, 1893