Search Documents

By A. G. Weber, H. J. Welge

A published calculation method for predicting incompressible, multidimensional fluid displacement has been adapted to the problems of water and gas coning in oil wells. Since depth and radial distance from the wellbore are the two key dimensions affecting the shape of a gas or water cone, coning calculations are well suited to the use of two-dimensional methods. The alternating direction implicit procedure (ADIP) was used for relaxation calculations of two-phase potentials in a two-dimensional grid. From the potentials and the capillary pressure relationship, saturation and pressure distributions were calculated which trace cone growth with time. Predictions have been made for well producing histories both before and after core breakthrough. To check validity of the method, two-dimensional calculations have matched the coning behavior and produced water-oil ratio history of a laboratory sand-packed model. They have also matched the coning behavior of several producing wells, for which the calculations were compared with produced water or gas cuts and logs showing water or gas cone movements. INTRODUCTION The application of two-phase, two-dimensional calculations using ADIP to various reservoir flow problems has been described in the literature.1-3 When adapted for computer solution, this method has proved to be a powerful tool for simulating well and reservoir behavior. This paper discusses the method as applied to well coning calculations. Single-well and coning calculations comprise an especially difficult class of two-dimensional problems which require special techniques for computer calculation and determination of reservoir characteristics. Refs. 4 through 8 describe previous approaches to the coning problem. Several examples of water and gas coning calculations, including studies on both laboratory models and producing wells, are presented here. The two-dimensional method accounts realistically for the most critical parameters affecting coning behavior, including production rate, formation stratification, horizontal and vertical permeabilities, depth of well penetration, gravity and capillary forces. The method considers the different densities and viscosities of the two phases and the relative permeability and capillary pressure characteristics of the rock and fluids. In addition to tracing cone growth in the vicinity of the wellbore, the method calculates the overall movement of the fluid interface throughout the well's drainage volume. Incompressible fluid flow is assumed to occur between the producing interval and the well's limit of drainage. Calculations can be made for the producing history both before and after cone breakthrough. A typical two-dimensional grid or array of blocks used to solve a coning problem contains about 400 blocks. The well's cylindrical drainage volume can be represented by about 20 radial subdivisions and the formation thickness by 20 vertical subdivisions. The grid spacing is normally smaller near the withdrawal interval to define the cone shape accurately. For this work we used an IBM 7074 digital computer having a core memory of 10,000 ten-digit words. A typical study, covering 5 to 10 years of well producing history, required from three to six hours of computing time. MATHEMATICAL SIMULATION OF CONING BEHAVIOR BASIC METHOD In coning calculations, the reservoir volume drained by the producing well is represented by a two-dimensional system of blocks as shown in Fig. 1 for water coning studies. The horizontal dimensions of the blocks increase with radial distance from the well axis in geometric progression, i.e., the block size is small near the wellbore and large near the well's drainage radius (re). Vertically, the blocks are bounded by horizontal planes located at different depths through the

Jan 1, 1965

By R. J. Blackwell, A. L. Pozzi

Scaled laboratory-model studies provide a powerful method for evaluation of a proposed oil-recovery process. In recent years, models have been used extensively to evaluate processes in which solvents displace oil, both for general cases and for specific reservoir conditions. Since the performance of a miscible flood in a horizontal reservoir can be significantly affected by transverse mixing between solvent and oil, this displacement mechanism must be accurately simulated in the scaled model studies. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long times for experiments. If scaling requirements for miscible displacements could be relaxed while accurate simulation of essential displacement mechanisms is maintained, the utility of model studies would be greatly enhanced. The purpose of the work reported herein was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascer tain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. These studies were performed with completely miscible systems in linear, horizontal models packed with unconsolidated media. From the experimental results, a set of relaxed scaling criteria was formulated which allows the requirements of geometric similarity and equality of the ratio of viscous to gravity forces to be omitted for specified conditions. The relaxed criteria are valid whether transverse mixing is by molecular diffusion or by convective dispersion. Correlations which permit prediction of vertical sweep efficiencies in linear, horizontal reservoirs were developed from the experimental data when transverse mixing is by molecular diffusion. These same correlations may be used when transverse mixing is by convective dispersion if an empirically defined, effective, transverse dispersion coefficient is used in the description of the mixing process. The effective transverse dispersion coefficient correlation essentially duplicates the dispersion coefficient correlation for equal-viscosity, equal-density fluid systems. Experimental values for the effective transverse dispersion coefficient can be measured readily. INTRODUCTION One of the most effective methods for evaluation of miscible-displacement oil-recovery processes is that of displacements in laboratory models scaled to simulate reservoir conditions. For these laboratory studies to be meaningful, however, the essential displacement mechanisms affecting reservoir performance must be accurately simulated. Since the performance of a miscible flood in horizontal reservoirs, or in dipping reservoirs at high rates, can be significantly affected by transverse mixing of solvent and oil, this mechanism must be considered in the design of laboratory experiments. Unfortunately, precise scaling of transverse dispersion coupled with the requirement of geometric similarity requires impractically large laboratory models and long experiment times. This difficulty seriously limits the utility of laboratory model studies. Craig,et al,1 demonstrated that geometric similarity is not required when mixing is unimportant. Their experimental data indicate, for the cases studied, that the displacement is sufficiently characterized by scaling the ratio of viscous-to-gravitational forces. This work suggests that relaxation of the requirement of geometric similarity and, possibly, other criteria might also be permissible when mixing is important, provided suitable groups describing the mixing process are scaled. The purpose of the work reported here was to evaluate the relative importance of various mechanisms affecting miscible displacement and to ascertain whether the essential features of the displacement process can be simulated even though some scaling groups are not satisfied. Consequently, laboratory investigations were made of the dependence of recovery on dispersion and other variables,

By J. A. Danko, C. D. Pears, L. D. Schmidt, J. P. McGee

This paper describes a pilot plant built on the campus of West Virginia University by the Federal Bureau of Mines station at Morgantown, West Virginia, for gasifying pulverized coal in a mixture of oxygen and steam at pressures in the gasifier up to 450 psig. The work upon which this report is based was done under a cooperative agreement between the Bureau of Mines and the West Virginia University. The goal of Bureau of Mines work at Morgantown is development of a low-cost process for producing mixtures of carbon monoxide and hydrogen for the modified Fischer-Tropsch synthetic-fuel plants, which may be shifted to produce hydrogen for coal-hydrogenation plants. Gasification with oxygen offers the inducement that the gas may be generated at the pressure at which the gas will be utilized in a gas-synthesis plant. Since the optimum pressure for the synthesis appears to be about 400 psig, the gas should be produced at approximately 450 psig to take care of pressure drops in the purification train and control valves. If the gas is generated at the pressure of utilization, only the oxygen need be compressed, not the raw synthesis gas. This means a saving in power of 5 hp per hour per 1000 cu ft (CO + H2), which is approximately a saving of 4 cents per gallon of gasoline. For example, consider a commercial plant generating 18,000,000 standard cubic feet per hour of raw gas that would produce approximately 10,000bbl of liquid product per stream-day. Assume that this gas would be 85 pd CO + H2 and that the oxygen required would be 320 cu ft per 1000 cu ft of CO + H2. The following estimate is based on a commercial centrifugal compressor. If the 18,000,000 std cu ft per hour of synthesis gas is compressed to 450 psig with 74 pd efficiency, 107,000 hp is required for compression. If the synthesis gas is generated at 450 psig pressure, only

Jan 1, 1953

By Albert D. Brokaw

THE accompanying chart was devised to provide a rapid and simple method of correcting for temperature and compressibility (deviation from Boyle's law) of gas under relatively high pressures and temperatures, such as are encountered in many deep reservoirs. The chart was prepared by interpolating for the desired values in the experimental data of Burke and Keyes1 and Kvalnes and Gaddy2 on the compressibility of methane, after adjusting their results from 0°C. to 60°F. and combining the correction factors for compressibility and temperature into a single multiplier, which, applied to the product of pressure and reservoir volume, gives at once the volume at one atmosphere (14.7 lb. per sq. in. abs.) and 60°F. The relationship 0f this multiplier to the compressibility factor Z, as used in most discussions, is simply: [Multiplier = 460° + 60°ZT –] where Z is the compressibility factor and T the absolute temperature (Rankine). Fahrenheit temperatures are shown on the vertical axis and pressures in pounds per square inch absolute on the horizontal axis. Correction factors or multipliers at intervals of 0.05 from 0.55 to 1.40 have been plotted on the chart and are calculated t0 give volume of gas at one atmosphere pressure (14.7 lb.) and 60°F. The operation is as follows: The reservoir volume, times the number of atmospheres pressure, times the multiplier, gives the volume of gas measured at one atmosphere (14.7 lb. per sq. in.) and 60°F. For example, a reservoir is estimated to have a volume of 10,000,000 cu. ft., bottom-hole pressure is 2940 lb. per sq. in. and temperature is 184°F To make the correction for methane, follow the 184° line horizontally to the 2940-lb. pressure line. The intersection lies between the 0.85 and 0.90 correction lines, and by interpolation we may estimate the multiplier at 0.863. The computation is simply: [ ] Using the chart for methane prepared by Prof. G. G. Brown3 and his associates, the multiplier is found to be 0.867. Details 0f computation are as follows: Correction factor to apply to PV to correct for deviation from Boyle's law and adjust to measurement basis of 60°F.: [ ]

Jan 1, 1941

By John Dasher, Wilfred L. Freyberger, James H. Pannell, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By James H. Pannell, John Dasher, Wilfred L. Freyberger, A. M. Gaudin

WHEN beryllium is bombarded by gamma rays under suitable conditions it evolves neutrons. This nuclear reaction, Bes + y + n + Be", [I] is utilized in the process that is described in this paper. The equation, which physicists often abbreviate to Bevy, n)Be" shows that a photon, y, is absorbed by the Be- sotope of beryllium which then emits a neutron, n, leaving Be8 as a residue." It has been determined that the threshold for this reaction is 1.63 mev; that is, gamma rays having an energy less than 1.63 million electron volts do not have enough energy to remove a neutron from the beryllium nucleus. The threshold value for the beryllium (y, n) reaction is lower than that for any other element. The next most sensitive element is heavy hydrogen (deuterium) whose gamma neutron reaction, D2 (-y, n) H1, has a threshold of 2.2 mev. Thus, gamma rays having an intensity between 1.63 and 2.2 mev will evolve neutrons from beryllium and from beryllium only. Nuclear reactions can be considered as occurring between a projectile and a target. The probability of the occurrence of any such encounter can be expressed in terms of the "cross section" of the target nucleus for the projectile and projectile energy. This cross section, then, is the area normal to the path of the projectile controlled by the target for the purpose of the reaction under consideration. Cross sections are usually expressed in barns, in which a barn is lo-" sq cm. The cross section for Eq 1 is very small, even for nuclear reactions, and of the order of 10"3 barns. It is therefore necessary that a high flux of gamma radiation at the appropriate energy be used to obtain an appreciable neutron yield. In view of the nuclear properties of beryllium it seemed that if pieces of beryllium ore on a moving belt were bombarded with an intense beam of gamma rays, those pieces which are rich in beryllium minerals would emit neutrons at a sufficiently high rate to make it possible to detect that emission, and to use it to actuate a mechanical device for removal of the active from the barren particles. The principal economic source of beryllium is the mineral, beryl. Beryl occurs mainly in pegmatites which are characteristically coarse grained. The suitability of mechanical concentration depends upon the size at which the desired mineral can be liber-

Jan 1, 1951

By P. J. Jacquard, C. Jain

Interpreting pressure measurements is one of the fundamental problems in the operation of oil reservoirs. The principal methods and means of study zuhich are currently used are reviewed. Emphasis is placed on the necessity of improving the quality of the information to turn it to the best possible account. One of the important aspects of the problem is the development of a system of automatic interpretation of the pressure measurements. The proposed method aims at this objective: starting from the relation which exists between a local perturbation of permeability and its effect on the velocity potentials in the wells, we determine by successive approximation the modifications to be made to the permeability map by fitting the least squares between the measured pressures and the pressures indicated by the mathematical model. The method has already been successfully employed in the case of heterogeneous reservoirs of radial- circular symmetry. Its application is extended here to the two-dimensional case, and is illustrated by two examples, for which the results are presented. The conditions required for the method to become fully operational are likewise analyzed. I — INTRODUCTION One of the basic problems of production and recovery from oil fields is interpreting pressure measurements made in wells in the single-fluid-phase regime. Simplifying assumptions, for example supposing the reservoir to be homogeneous, make it possible to use more or less simple methods which permit the estimation, from these pressure measurements, of a mean value of the permeability around the wells. Considering the actual heterogeneity of the majority of reservoirs, and the phenomena of interference between wells, these methods are only indicative. Much has been published on the studies of different cases of comparatively simple heterogeneity: some have discussed the radial heterogeneity around a single wel1,l or vertical heterogeneity.2 The results of these works have shown the influence of variations of permeability on the pressure, but unfortunately they are not very useful in practice because they all are concerned with the phenomena around a single well, without interference between wells, and they correspond to relatively simple and theoretical schemes. These studies of reservoirs or parts of reservoirs on a larger scale are made by the electric analyzer or digital model. We define a permeability map and a porosity map, then reproduce the production history of the wells on the wells of the model, and note the corresponding pressures. These pressures are then compared with actuality, and the discrepancies observed are analyzed. From this analysis we deduce the modifications to be made to the maps of permeability and porosity, and repeat until the coincidence between the pressures indicated by the model and the actually observed pressures is considered adequate. We have adjusted the model. Obviously, in this method of investigation, everything depends on the formula which permits the modification of the permeability to approach the adjustment. Considering the complicated nature of the problem, some oversimplified formulas are poorly adapted to reaching a good adjustment. For example, we have shown that the elementary operation of increasing the permeability not far from a producing well to compensate for too low pressures in the well can, in certain cases, express itself by an effect exactly opposite. 3 The project described here is for a system where we begin with the pressure measurements and the several known parameters of the reservoir, and develop the most probable permeability map, taking account of the measurements available and a subdivision of the reservoir fixed a priori. Ideally, this system is conceived as one in which no manual intervention would be necessary. The model simulating the reservoir is only one part of the whole system, and it is neither the longest nor the most complex part. The need to integrate the model into an aggregate of much more extensive processes has led to the adoption of the digital solution, even though a solution combining the digital and the analog is perfectly conceivable. The simulating model is in that case no more

Jan 1, 1966

By Billy L. Crowder, John M. Fairfield

The implantation of B+ , P+, and As&apos; into silicon has been studied with the purpose of making shallow p-n junctions. The influence of such parameters as 1) ion energy, 2) target orientation and temperature, 3) total dose, and 4) annealing schedule was investigated. An energy range of 70 to 300 kev was used for boron and phosphorus implants and up to 500 kev for arsenic. It is found that the experimental projected range agrees well with theory and that shallow junction depths can be made reproducibly. ION implantation has received much attention recently as a technique for doping semiconductors. Specifically, it has the potential of supplementing or replacing the diffusion process as a method for making p-n junctions. In a few specific cases it has been used successfully to make semiconductor junction devices. Potential advantages of ion implantation doping over diffusion techniques are: 1) It affords greater control of shallow junction depths (< 0.2 µ) while maintaining high peak concentrations. This is particularly important for high-speed switching devices, since lower junction capacitances and resistances can be achieved. 2) More precise registration of small planar structures can be realized if proper masking procedures are employed. This advantage is especially useful in the design of high-density integrated circuits. It has been used to advantage in FET fabrication since the edge of the source or drain can be aligned precisely at the edge of the gate electrode.&apos; 3) Ion implanatation permits lower temperatures than diffusion techniques. This factor alleviates the problem of compatibility of diffusivities often encountered when designing multiple-junction structures. Also, the lower temperatures create fewer thermal defects and dislocations, which may account for the high efficiency of some ion-implanted solar cells.2 4) Impurity profiles can be more easily tailored to resemble ideal distributions. Successful exploitation of the potential advantages of ion implantation techniques will depend on increased knowledge and understanding of the subject. The factors likely to be influential in determining impurity distribution profiles in ion-implanted single-crystal targets have been reviewed by J. F. Gibbons.3 In addition to the mass and energy of the implanted ion, the total dose, target orientation, and target temperature are important parameters. The annealing temperature required for removing lattice damage and incorporating the implanted species on an electrically active site is very important. This paper describes an investigation of some of these factors. Implants of boron, phosphorus, and arsenic into silicon have been studied. Energy ranges of 50 to 300 kev were used for boron and phosphorus and up to 500 kev for arsenic. In addition to the implantation energy, the effects of total dose, target temperature, and post implant anneal have been investigated. EXPERIMENTAL PROCEDURE The implantation targets were silicon wafers cut from Czochralski-grown crystals, lapped, and chemically polished. The orientations were (111), (110). and (100) with misorientations of up to 7 deg from the principal axis. For this study, accurate target alignment (i.e., within 0.1 deg) was not available and quoted misorientation values should be regarded as approximate . The implantation equipment consisted of an ion source, a 300-kev linear accelerator tube, an electromagnetic separator, and the associated target supporting and beam focusing assemblies. The ion source was a simple oscillating electron type source,4 which has been described elsewhere.5 The gaseous compounds BF3, PF5, and AsH3 were used as ion sources for B+, P+, As+, and AS+&apos;. Analyzed current levels of up to 20 pamp could be obtained; however, for this investigation target current levels of 1-3 µ amp were usually employed. The analyzed ion beam was collimated through a double slit (1.4 x 0.4 cm) and swept perpendicularly to the long axis of the slit such that an area of about 2 sq cm on each target was covered. Dosages of around 1015 cm-2 were normally employed, but smaller amounts were also used for comparison. A uniform flux density over the bombarded area was assured by the continuous use of profile monitors similar to those described by Wegner and Feigenbaum.6 Post-implant annealing was accomplished in an argon atmosphere in a temperature range of 600" to 950°C. It was not part of the purpose of this investigation to study the annealing kinetics; however, some isochronal and isothermal anneal experiments were conducted to determine the time and temperature necessary to render a reasonably high portion of the implanted ions electrically active (i.e., higher than 50 pct). Post-implant anneal temperatures of around 900° and 600°C were required for boron, and arsenic and phosphorus implants, respectively. Arsenic and phosphorus implants increased in conductivity rather abruptly at the proper anneal temperature of the isochronal curve, but boron increased more gradually over a wider range. Isothermal anneal curves were reasonably flat after 10 min, so an anneal time of 1/2 hr was used for the experimental results described below. The profiling techniques were: 1) neutron activation analysis, 2) differential sheet resistance,7 and 3) junction staining.8 The differential sheet resistance technique is commonly employed in this type of study. Its principal disadvantage is the uncertainty of the ef-

Jan 1, 1970

By J. Federico Price, Joseph E. Aparicio

This paper describes the production of a specific iron oxide pellet that has given very good and consistent results as feedstock for HYC-Process Direct Reduction Plants. The sponge iron originated from these pellets has been used for the economic production of almost 15 Mt of low carbon steel via electric arc furnace meltshops. An overview of mining, beneficiation, pelletizing, direct reduction and steelmaking for this case is given with emphasis on the charactertitics of the self-fluxing oxide pellets.

Jan 1, 1982

By A. D. McMaster, M. L. Gimpl, N. Fuschillo

Low-power, high-speed, radiation-resistant, monolithic thin-film integrated circuits require thin-film resistors of high sheet resistance which are compatible with the processing requirements for monolithic silicon devices. For this purpose the structure and electrical resistance as a function of temperature were investigated for Nichrome-silicon monoxide cermet films on passivated single-crystal silicon substrates. A suitable material was found to be a mixture of 50 vol pct Nichrome-50 vol pct silicon monoxide. This mixture, when evaporated onto 300°C substrates. showed a low temperature coefficient up to 400°C, at both 270 and 1100 ohms per square. Resistors deposited on room-temperature, 300°, and 500°C substrates were heat-treated at 600°C in air for short periods of H- seed, low-power, radiation-re sis tant, monolithic thin-film integrated circuits&apos;-3 require thin-film resistors of high sheet resistance and low temperature coefficients of resistance which are compatible with the processing requirements for monolithic silicon active devices. The present investigation is directed towards the replacement of the Nichrome in the sandwich-type SO2-Nichrome-SiO resistors, currently used for DTL monolithic thin-film integrated circuits, with codeposited Nichrome-SiO cermet resistors. These Nichrome-SiO resistors are provided with an overcoat of SiO and are deposited onto thermally oxidized silicon wafers used in monolithic mi-crocircuit technology. The cermet resistors are shown to provide a lower temperature coefficient of time totaling up to 45 min. Electron nzicrogvaphs and diffraction patterns were taken of the as - deposited and heat-treated films. These results were then compared with electrical-resistance measurements for each condition. The room-temperature and 300°C substrate films showed a large decrease in resistance. The 500°C substrate film remained stable throughout the entire cycle. Electron-microscopy results show that the increased stability after heating to 600°C is largely due to crystallization of the films which begins in the vicinity of 400°C. The slight oxidation of the films when heated in air had a negligible effect on the resistance. The resistance of the film was a function of the substructure. resistance and a more versatile compatibility with silicon monolithic processing. Previous work3, on chromium-SiO coevaporated cermet resistors on glass and ceramic substrates without overcoats of SiO has been reported. For the present application, the thin films should possess the following ideal requirements: a) a temperature coefficient of resistance as near zero as possible up to 300°C; b) have a sheet resistance higher than 200 ohms per sq to conserve space on the chip; c) be easy to evaporate; d) be oxidiation- and radiation-resistant; e) show long-time stability at 100°C; } be stable in N2 atmospheres up to 600°C for short periods of time (5 to 45 min). Requirements a to e are well-known. The last requirement was optional and was due to a mask elimi-

Jan 1, 1967

By F. E. Bedale

STUDY of several severe mine explosions that occurred during the winter of 1907 led to the belief that coal dust was a definite explosion hazard. The Consolidation Coal Co. was a pioneer in the early work to&apos; eliminate this hazard and to combat the dangers incident to poor ventilation and the presence of methane. Maintenance of high humidity throughout the mines was one of the first measures adopted, later to be superseded by rock-dusting. In the twenty years from 1907 on, many safety measures were developed and adopted, and several prizes were won, though the practice was crude by present-day standards. But in 1927, the company went to work in earnest, and organized a Department of Safety with adequate personnel and with authority to enforce all approved rules for the prevention of accidents and the preservation of company property. All plans for new construction work, changes in mining systems, and proposals for the purchase of new mining equipment had to receive the approval of this Department. A set of operating- and safety standards was written to govern the activities of all employees, and physical examinations for them were required.

Jan 1, 1938

By Richard W. Lodge

In the crucible-method of assaying ores for silver a certain amount of litharge is essential to supply sufficient lead to collect the precious metals. The object of this paper is to point out that the use of a large excess of&apos; litharge in the assay of some ores will give results for silver that are uneven as well as low. So far as I know, however, an excess of litharge does not affect the results obtained in the crucible-assay of ores for gold. The main reasons for using, in the crucible-assay, much more litharge than is required to givc the necessary lead button are: 1, its action as a flux; 2, its action as a desulphur-izer; and 3, its action as an oxidizer, especially on metals like copper and nickel, whereby they are forced into the slag as oxides and thus prevented from passing into the lead button. Hence, by the use of much litharge in the crucible-assay more ore call often be taken than in the scorification-process, and a lead button obtained which call possibly be cupelled at once or after a single scorification. The method is specially advantageous with an ore carrying much copper or similar impurity and poor in silver, when the assayer does not wish to resort to a wet-analysis for the determination of the silver. It is well known that some ores give better results when assayed by the scorification-method, while others give better results by the crucible-method. For several years I have noticed that, when much litharge was used with certain sulphide and arsenical ores, the results were considerably lower than when the scarification-method was used. This fact was more forcibly brought out in connection with certain work carried on this year by Messrs. H. A. Frame and

Jan 1, 1908

By W. J. Skewes, C. T. Holland

Properly constructed stopes are necessary underground for proper ventilation and safe, healthful working conditions. Mining companies are concerned with providing the best possible stoppings at an economic cost. It is important to consider 1) proper materials, 2) construction that ensures maximum performance from the material used, and 3) keeping costs within reasonable limits for the unit operation—stopping—involved. The authors investigated all aspects of the problem and have attempted to layout a study program to provide information on all phases. Mining companies every year purchase huge amounts of material for the construction of ventilation stoppings. This material by the time it is in place in the stoppings will cost the company many thousands of dollars. In addition and more importantly these stoppings are supposed to confine air travel along certain well defined paths into areas where it is needed to provide safe and healthful atmospheres for workmen. The cost of forcing this air through the mine is large and in general increases as the total quantity increases. Consequently, if the stoppings leak, increased cost results and in addition unsatisfactory ventilation may prevail in the mine. Therefore, it is essentia1 to provide the best possible stoppings at an economic cost. When attempting to provide the best stoppings possible at an economic cost, three aspects of the problem must be considered. These are 1) getting the most suitable material for stopping constructions, 2) constructing the stopping so as to get the best performance from the material used, and 3) keeping the cost of stopping construction to a minimum for a suitable stopping. This investigation is concerned with all phases of the problem and has attempted to lay out a study to provide information on all of them. In order to develop information on the best stopping material available it seemed wise, after con- sidering the job a stopping must do, to investigate the following aspects of material used for stoppings: 1) strength in compression, 2) compressibility or yield under load, 3) porosity, and 4) permeability. To provide information on the best manner of construction the following aspects of air leakage through the stopping were investigated: 1) when the stopping is built of dry stacked materials—i.e., the joints are not mortar-laid (See Fig. 1); 2) when the stopping is built of dry stacked material and then plastered on one side (see Fig. 2); 3) when the

Jan 1, 1961

By S. Ramachandran, R. A. Walsh, J. C. Fulton

A method has been developed for calculating the oxygen content of commercially melted stainless steels. Application of thermodynamics to the de-oxidation reaction in straight chromium and Cr-Ni stainless steels has resulted in a set of equations DURING the past 30 years, many rewarding developments have resulted from the application of physical chemistry to steelmaking. A need still ex- which permits the calculation of oxygen contents. The model was programmed for computer calc~ilations. The validity of the method was demonstrated on routine oxygen samples from numerous commercially melted heats of stainless steel. ists for further progress in the use of thermodynamics to meet the more stringent requirements for cleaner steel. Current electric furnace practices have been developed around minimizing residual-oxygen content, one of the most important factors controlling the inclusion content of stainless steels. The residual oxygen is controlled by the use of deoxidizers during the finishing period and a number of empirical rules have been evolved. Although this feature of electric furnace practice has long been in use, only in recent years has funda-

Jan 1, 1963

By T. S. Lundy, R. A. Padgett

The fact that cobalt diffuses in silver at a much slower rate in a region near a free surface than in bulk material has been demonstrated in a variety of experiments. Various possible mechanisms of this near-surface effect (NSE) are examined in light of experimental evidences. The tendency for surface segregation of some solute atoms appears to be a likely mechanism to explain the effect. UNIDIRECTIONAL and isothermal diffusion from a plane source of radioactive tracer into an isotropic, homogeneous medium follows the Gaussian solution to Fick&apos;s second law, or: where A(x,t) is the position and time-dependent concentration of the diffusing species, M is the quantity of diffusant per unit area initially at x = 0, and D is the diffusion coefficient. For a given time, say t = tl, one can easily see that: d In Aixji)_____1_ r2] d(x2) 4Dti Thus, if diffusion data obtained by serial sectioning are plotted as In A(x,tl) vs x2, the diffusion coefficient is obtained from Eq. [2]. The ideal behavior seldom is observed in real systems. Deviations from ideality generally occur either at small or large values of penetration distance. The overall picture is shown schematically in Fig. 1 where Regions I, 11, and 111 are due, respectively, to some near-surface effect or effects (NSE), volume diffusion, and short-circuiting effects. For different systems and conditions of specimen preparation and analysis, the relative importance of Regions I, 11, and I11 may be drastically different. Region I is completely absent in many systems and there is no NSE. In others, however, there may be considerable difficulty in determination of volume diffusion coefficients due to the overshadowing influences of Region I. Such is particularly true when indirect techniques such as the surface concentration decrease or the Gruzin method&apos; are used to find D. In this paper several experiments which had as their goal a better understanding of near-surface effects are reported. Specifically, it is well-known that unusual penetration behavior results for the diffusion of several impurities in ilver- and that considerable controversy exists with regard to interpretation of the published diffusion data. We chose to examine those unusual results which occur for cobalt diffusion in monocrystalline silver395 primarily because knowledge of experimental procedures and materials were readily available. Both radioactive co60 and co5&apos; could be utilized to offer a wide range of available concentration of the diffusing species. Experiments were also performed on the diffusion of AgnO in silver. They gave base-line data for the system—both for technique evaluation and for examination of the vacancy distribution near the surface. I) PROCEDURES Cylindrical-shaped specimens 1.25 cm diam and 1 to 1.25 cm long were cut from 99.999 pct Ag single crystals obtained from Monocrystals Co., Cleveland. One end surface of each specimen was polished flat and etched with a mixture of 20 ml saturated Cr03 solu-tion-20 ml H20-3 ml concentrated HC1. Radioactive tracer (co60 or co5&apos; or Ag&apos;lO, each having a radio-chemical purity of greater than 99 pct) was deposited onto the prepared surface either dropwise with evaporation to dryness of the solution containing the tracer (0.5 N HC1 solution for the co60 and co5&apos; and 0.6 N HNO3 solution for the A"&apos;), by electroplating, or by evaporation from a tantalum or tungsten filament in an evacuated bell jar. The amount of deposited cobalt was varied from many atomic layers of cobalt containing the co60 to approximately one co5&apos; atom per lo6 surface atoms of silver. This large variation in amount of deposited cobalt yielded information about both the influence of a thick-source layer of tracer and solubility effects on the NSE. Such variations were possible because of the large differences in half-lives,

Jan 1, 1969

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district&apos;s production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state&apos;s total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

By D. V. Carter, F. M. Hackbusch

Beginning the year 1938, the East and East Central Texas district comprised 48 counties, which is equivalent to the Texas Railroad Commission districts 5 and 6. At the close of the year there were 46 oil and gas fields in this district. Eight other fields, seven oil and one gas, have been abandoned. Exploratory Drilling During the year, 113 exploratory wells were drilled. Nine discoveries were made, five of which proved to be oil fields, three distillate, and one gas. Completions for the district were 2043 oil wells (distillate wells included), 36 gas wells and 163 dry holes. Exclusive of the East Texas field, the Marion County extension of the Rodessa field led the district in the number of completions during the year. Production and Proration All fields in the district produced a total of 182,369,484 bbl. of oil, a decrease of 12.57 per cent compared with the 208,594,453 bbl. produced during 1937. The East Texas field produced 148,189,913 bbl., which was 81.6 per cent of the district&apos;s production for 1938. November daily average oil production for the East and East Central district was 469,102 bbl. The estimated cumulative production to Jan. 1, 1939, for this district was 1,753,894,802 bbl. It is estimated that the East and East Central district produced 38.9 per cent of the state&apos;s total production for the year, which was 468,781,632 barrels. The decrease in 1938 production, as compared to that of 1937, in this district was partly due to the Saturday and Sunday shutdowns, 71 days for the year, which is equivalent to 19.45 per cent of the year. All fields in this district were affected by shutdowns except the Texas portion of the Rodessa field, which was shut in only during January and February. Certain wells were exempt from these shutdowns because of special pro-

Jan 1, 1939

THE Mining Methods Committee during the past year has spent much of its time developing the interest of members of the Institute in the work that comes under its direction. The response on the part of the membership has been most encouraging and in order to give a concrete form to the program which it hopes to develop, an "Outline for Papers on Mining Methods" has been drawn up and is herewith submitted for consideration. This outline has slowly taken shape until it now represents ideas contributed by a great many men, and it is hoped that it will be suggestive and helpful in the preparation of papers. This program can be used for the preparation of papers covering single large operations or, preferably, as the basis for a description of methods and the presentation of results obtained either in different districts or in different branches of the industry. The Committee presents this outline for the consideration of the various Sections of the Institute with the request that they will endeavor to interest the members of the Sections in covering comprehensively the mining operations with which they are connected. It is not the plan of the Committee to publish a paper on every mine, giving all the details outlined, but rather that an engineer familiar with a district prepare the general information and engineers of each important mine in the district compile the specific information of the mine with which they are connected. The general information and the specific information shall be sent to the Committee, and with this information the Committee will prepare a paper on the results obtained under the various mining methods in the different districts. The Committee requests that all papers shall be compiled under the direction of the Chief Engineer of the company and then submitted to the General Manager before acceptance for publication or compilation and tabulation with other similar data. Where the study of this subject approaches the fields of other standing committees of the Institute, the

Jan 5, 1922

By M. E. Wadsworth, T. D. Chatwin

The kinetics of sulfidization of hematite (Fe203) by H2S gas at various partial pressures have been determined over the temperature range of 170° to 500°C. The process was controlled by thin films of pyrite (FeS2) and troilite (FeS) which were protective and formed diffusional layers. At higher temperatures the thermodynamic drive to form FeS2 decreased, and consequently the rate of formation of FeS, decreased. Conditions for the development of thin layers of FeSz consisting of 10 to 100 atomic diameters are presented. Laboratory flotation results on synethetic ores indicate floatability identical to that of pyrite of normal xanthate flotation. The prospect of high-temperature sulfidization of metal oxides using H2S, S, or other sulfur bearing compounds is intriguing as a potential activation process for flotation since the thermodynamics are very favorable for a large number of systems. If the kinetic parameters are sufficiently well understood it may be possible to provide surface sulfide layers a few angstroms thick, thus imparting normal sulfide floatability characteristics to the oxide. For thin layers the total sulfur pick-up would be small except for very high surface area materials but in most cases this sulfur could be readily removed by roasting if necessary. The general reactions for the sul-fidization of metal oxide MxO, to a metal sulfide MpSq using H2S may be written for the three conditions py > xq; py < xq; and py = xq: A large thermodynamic advantage is obtained in many systems because of the relatively large negative free energy of formation of H,O compared to H,S. For the temperature range 2S° to 1500°C &apos; where AFOis the standard free energy and T is absolute temperature. As is evident from Eqs. 4 and 5, the free energy of formation of H ,0 is approximately 35 to 37 kilocalories per mole greater than that for H,S over broad variations of temperature. For oxide-sulfide systems as outlined above, sulfidization may be expected to occur for the conditions: Groups I and 111: that is, if the terms on the right are more negative than those on the left the reaction is expected to occur thermodynamically. The value hFg,(,) is included in Eq. 6 since hFLzs is based upon gaseous S2 rather than the normal reference state, orthorhombic sulfur. The

Jan 1, 1969

By R. J. Marcotte, C. T. Eddy, R. J. Smith

THE objectives of the investigation herein reported were to determine: (I) the S-curves for certain selected cast steels, (2) whether or not the published S-curves for wrought steels are satisfactory for use on cast steels of similar composition, and (3) to prepare hardenability curves of the selected cast steels. In order to make the final comparisons between cast and wrought steel more completely tangible, it was deemed advisable not only to determine S-curves for the steels submitted in the cast condition but also to roll some of the cast-steel test bars and determine comparison S-curves on such wrought material. This procedure eliminates the composition variable and makes it possible to reveal the differences resulting from plastic deformation of the cast structure in addition to providing the comparison with published data on wrought steels. CAST STEELS The cast steels selected for the preparation of S-curves, or time-temperature transformation curves, were similar to S.A.E. series 1030, 2330, 4130 and 4330. Of these the 1030 was supplied by The Crucible Steel Casting Co., Cleveland, Ohio, and the other three by The Sawbrook Steel Castings Co., Lockland, Ohio. The steels were furnished in the as-cast condition. The manufacturers supplied the chemical analyses and the properties that could be obtained in the heat-treated condition-all of which is summarized in Table I. [ ] PROCEDURE The metallographic and dilatometric procedures and equipment were in general standard. The specific technique employed was described in a report of the Steel

Jan 1, 1945