Search Documents

By D. J. Carney, J. Chipman, N. J. Grant

SINCE the beginning of this century it has been known that hydrogen contributes to the porosity of steel and that it is harmful to its mechanical properties. The evidence for this has been largely qualitative. Steel to which hydrogen was purposely added. in sufficient .amounts was shown to be either porous or brittle or both, whereas similar steel of low hydrogen content was shown to be free of porosity and to possess normal physical properties. There have been a considerable number of qualitative experiments of this type. Also, early in this century, a few attempts were made to measure the amount of hydrogen normally dissolved in commercial steels. This was usually done by placing the sample under an inverted liquid column such as mercury and collecting the evolved gas. These attempts, while not successful in measuring actual amounts of dissolved hydrogen gas, were able to prove that this gas will diffuse out of steel at room temperature, and that the amount of hydrogen dissolved is normally very small. On the basis of such qualitative evidence, hydrogen has been and still is blamed for a great number of the troubles encountered in the steel industry. In recent years, partial solutions for many steel-working problems have been obtained. These have led to increased interest in accurate quantitative work on hydrogen in steel, with the expectation that the results might possibly answer a few of the remaining unsolved problems. Commercially, two of the obvious questions which are in need of an answer are: (1) what are the most important sources of hydrogen, and (2) what quantity of hydrogen can be tolerated in various steels? There are many other unanswered questions. To begin to find the answers it seemed logical to start at the beginning of steel production with the liquid metal. Further, it seemed almost imperative to solve first the problems of analysis and sampling of the metal for hydrogen. Once these problems have been solved, it would be possible to answer more of the important commercial problems mentioned above. As a consequence, it was decided to design an analytical apparatus and, upon satisfactory completion of this, to develop an accurate method of sampling liquid metal for hydrogen.

Jan 1, 1951

By Wei-Kao Lu

A general rate equation is derived for gas -solid reactions in metallurgical processes by considering the contributions of chemical reaction at inter-phase boundaries and diffusion through the solid product layer simultaneously. This equation takes care of the whole range continuously from purely diffusion control to purely chemical reaction control. The parabolic law,' McKewan's equationa derived with the assumption of interface area control and the equation derived by Kawasaki et al. with the assumption of purely diffusion control are found as the limiting cases of the corresponding forms of the general rate equation. Many metallurgical processes involving gas-solid reactions have been extensively studied. The common examples of these processes include the reduction of oxides to metallic products, the roasting of sulfides to oxides or chlorides and the oxidation of metals. Gas-solid reactions consist of at least two kinds of steps; one involves the transport of reactant and product to and from the reaction zone and the other is the chemical reaction taking place at the interphase boundaries. In the limiting cases one or the other of the above mentioned steps will be much slower than the other and is then rate controlling. For example, the oxidation of metals is diffusion controlled and obeys the parabolic law.' On the other hand, if the diffusion rate is much larger than the chemical reaction rate then it will be controlled by the chemical reaction rate. This latter case occurs for the reduction of iron oxides studied by McKewan. If the rate of diffusion and of the chemical reaction have the same order of magnitude, a more detailed analysis is necessary. Thus at the beginning of the reaction when the solid and gaseous reactants are in direct contact, the reaction should be chemical reaction rate controlled as no diffusion process is involved. At the other extreme as the reaction zone moves further into the solid, the diffusion distance becomes greater and the diffusion rate continuously decreases. Eventually, therefore, for a sufficiently large sample the rate must become diffusion controlled. As the transition from one controlling step to the other must be continuous, we cannot describe this transition period by either of the two limiting cases. In this paper the author attempts to derive a general rate equation for gas-solid reaction systems. This is effected by considering the rates of diffusion and chemical reaction simultaneously from the state of pure diffusion control to pure chemical reaction control. I) DERIVATION The system under consideration is made of at least three phases, namely the gaseous one, the solid reactant, and the solid product as shown in Fig. 1. The notations are listed at the end of the paper. The mass transfer process involves the diffusion of reactants and products across the solid product layer. It is reasonable to consider that no chemical reaction will take place in the solid product layer with respect to both gaseous reactant and product. For the characteristics of local equilibrium of the system, the diffusion process is really in a quasi-steady-state. It will be proved in the following paragraphs. Then we can invoke the law of conservation of mass valid for all chemical species passing through the layer. The solid reactant sphere has an initial radius, ro, after a fraction of completeness of the reaction, the unreacted core has a radius ri, where r, is in the solid product region. Let Cg be the activity of gaseous reactant in the

Jan 1, 1963

By Thomas D. West

The occasional reports of progressive furnace-men, giving the results of physical tests to prove the superior qualities of their pig-irons, have encouraged the writer to believe that the time is ripe for the discussion of such work, and the inauguration of some correct system by which the furnace-man and the founder could make intelligent comparison of the elements of strength, deflection, contraction, and chill presented in pigmetal. In most cases the physical tests now made by furnace-men define but one quality in the iron, and are generally too vague to permit any true comparison. For example, one furnaceman tells us he can punch holes in his cast-iron, wishing it to be inferred that the iron is very soft and strong. Another furnace casts a long wedge, the thin end running to a knife's edge, which is supposed to prove the fluidity of the iron, for the founder's benefit. Another casts in square-cornered " chills," to define the hardness or softness of the metal. To the writer's knowledge these tests are not advocated by their originators as suitable for standards; and they are, to his mind, but evidence of unrest on the part of progressive furnace-men, who feel that something should be done in the line of physical tests. The writer knows of no furnace-men who make and keep records of the strength of their iron obtained by means of tests made on recognized standard testing-scales ; but he does know of a prominent furnace-salesman, who, not long ago, came into possession of a 1-inch square bar that stood 1400 pounds

Jan 1, 1897

By John M. Lovejoy

CURRENT production of petroleum on such a vast scale presents many interesting problems- the solutions of which are important not only to those directly interested in the business, but to the nation as a whole. The industry is relatively young. Until the discovers of the Lucas gusher at Spindletop in 1901 petroleum production had not exceeded 60,000,000 bbl. per year compared with 1,100,000,000 bbl. in 1936. In 36 years then, the modern oil business, production, transportation, refining, and marketing has developed. I will first present a brief history. of oil production as a background for consideration of the present situation.

Jan 1, 1937

By Robert W. Hunt

In 1888 the writer had the honor of submitting to the Institute a paper on " Steel Rails and Specifications for their Manufacture."* In his judgment the specifications were sufficient for "that day and generation." In that paper I said: '' The first duty falls upon the railroad engineer in designing his section. If that is bad, the steel-maker will be heavily handicapped in trying to furnish a satisfactory rail. I suppose it is hopeless to expect the adoption of standard sections."

Jan 1, 1896

By M. M. Rao, P. G. Winchell, R. J. Russell

A detailed analysis has been used to correlate the avalable thermodynami c da In on iron-ric11 Fe-Ni (41loys in the body-centered a, and the face-centered y phases. The inp ut injovrt~ation required by the a am lysis consists of tile heat of the a, to y transformation at 1123°K, the heat of mixing of y at 1123°K, tile specific heats of both a, and y (decomposed into Debye, electronic, and magnelic contributions), and the positional and magnetic entropies of both a, and y. PYLrrzary oirt.bul of the analysis is the free energy of each phase as a Junction of temperature and composition. FOr Fe-Ni alloys the adjustment of twenty-one parunletevs allows the accurate reproduction of enthalpy data for both phases, the heat of mixing- for y, the a/y equilibrinm compositions in the Fe-Ni phase diagram, and the usually accepted enthalpy and entropy of a and y iron. Also obtaitzed are fuirly accurate reproductions of electronic specific heat coefficients predicted from electron- to-atom ratio interpolations and To temperatuves eslimanted from transformation studies. Also considered in the calculation are the elastic constants, Curie temperatures, saturation magnlelizalion values, and indications of short- range order. The measnred activity coefficient of iron in anstetnite could not be accurately matched. The major source of uncertainty in the model is thought to be the magnetic contribution to the entropy of austenite. Calcrclations were extended to Fe-ni-C alloys using available carbon-acliuity data. The free energy of transformation from martensile to r at fixed composition was obtained as a function of nickel and carbon contetzt, and binary thetal-carbon phase diagrams Were estimaled as a function of nickel contenl. We needed thermodynamic information for Fe-Ni and Fe-Ni-C alloys at temperatures between 400" and 800°K in order to interpret the results of several phase-transformation studies. The most recent theoretical analysis of the thermodynamics of Fe-Nialloysl was based on a lumped-parameter, regular-solution model and used the Fe-Ni phase diagram available at that time.' Because significant difficulties were encountered in attempting to extend this analysis to Fe-Ni-C alloys, and because more experimental data has become available recently, we decided to attempt a new correlation. The analysis used here allows the extrapolation of measured and calculated thermodynamic values to lower temperatures and the extension of the thermodynamic analysis to Fe-Ni-C alloys. The structure of this correlation consists of expressions containing a total of twenty-one adjustable parameters. The forms of these expressions are discussed in the next section; however, a less formal summary is presented now to provide a physical overview of the model and to indicate its connections to prior work. Primary input information for this correlation is described below. The measured values of the specific heat of iron3 and its analysis475 and theoretical estimates of the specific heat of y* iron at low tempera- loys at 1123°K has been measured by solution calori-metry.7 The enthalpies of both a, and y have been measured most recently by Scheil and Saftig,B who used a dry-ice calorimeter. These data are used to formulate expressions for the heat of mixing of y and the heat of transformation of a, to y both at 1123°K. The a and y solubility limits in the Fe-Ni phase diagram have been redetermined recently9 by methods which assure a close approach to equilibrium. The a to y transformation can occur without change in nickel content or free energy at a temperature called TO; TO temperatures for various nickel contents have been estimated from transformation studies. The computed free-energy functions are adjusted by means of the parameters to fit both the phase diagram and the TO temperatures. Primary emphasis is placed on the phase diagram fit. Iron activities have been measured in Fe-Ni austenite10 between 973" and 1173°K. These activity data, which cannot be fitted accurately with our model, indicate that iron is substantially ideal in iron-rich austenite. Secondary, but helpful, information for the present correlation is provided by neutron diffraction and saturation magnetization measurements on both body-centered and face-centered Fe-Ni alloys."-'3 These results were interpreted11 in terms of composition-insensitive, localized magnetic moments on both iron

Jan 1, 1968

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank' standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1942

By Rush N. Hosler

This paper was prepared for the purpose of answering some of the many questions as to why, in the construction of Pennsylvania's Coal Mine Schedule Rating Plan, various factors were, or were not, taken into consideration. Much has been written about merit and schedule rating of industrial risks from an actuarial viewpoint, therefore this phase of the question is taken up only so far as may be necessary in presenting the practical application of the plan now in use. Companies writing fire insurance, about 30 years ago, were the first branch of insurance to use schedule rating; the values assigned their items were largely a matter of judgment. In 1913, the Industrial Commission of Wisconsin evolved the first schedule rating plan to be applied to industrial risks under compensation insurance. Pennsylvania, in 1916, with the inception of its Compensation Act, was the first state to apply the principles of schedule rating to coal mines. A definition of the term "schedule rating" submitted by the writer in a brief to the Safety Committee of the United States Coal Commission is as follows: Schedule rating, as applied to compensation insurance, is an instrument to measure the hazard of known causes of accidents to which employees are exposed in industry and thereby determine an insurance rate commensurate with said hazard. It was first applied to Coal Mining in 1916 in Pennsylvania.' In other words, for a mine operator to insure his employees for injury under the Workmen's Compensation Act, it is necessary that he pay a certain premium based on his payroll. If all mines were assessed the same premium, it would be unfair for the mine with low natural hazard, good safety conditions, and good accident experience to pay the same premium as a mine with bad conditions and experience, therefore schedule rating was introduced.2

Jan 1, 1925

By J. Farkas

A techno-economic assessment for the recovery of several elements from seawater is presented. Gold recovery has been used as an illustration for the economic evaluation of several processes. Current technology does not present any economically viable alternative to recover gold from seawater because its concentration is several magnitudes too low. However, with the increasingly larger availability of concentrated seawater, mainly from desalination and other processes, coupled with advances in technology, especially genetically modified specific microorganisms, may make the recovery of gold and other desired elements from seawater a reality in the near future.

Jan 1, 1984

By Simon T. Johnson

Potential applications for boom tunnelling machines requires reliable assessment of in-situ performance. The majority of existing classification schemes concentrate on the prediction of excavation rate, neglecting the important influence of tool consumption rates. A statistical approach is taken to the analysis of the performance data, which was obtained first-hand through in-situ monitoring, and laboratory testing of representative rock samples. A statistical discrimination technique is used to produce a scheme for the prediction of performance groups, each of which covers a limited range of cutting rate and/or tool consumption rate.

Jan 1, 1984

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By T. D. Mueller, H. Dykstra

This paper describes a method for obtaining compositions of gas and oil phases in equilibrium with each other at a given reservoir temperature and pressure as lean or enriched gas is injected into a reservoir oil not in equilibrium with the gas. The method is based on calculation of equilibrium constants, K, from the equation log Kp = A + B F, where p is pressure and F is component characterization factor. A and B are constants that vary with a composition parameter. The paper explains how A and B could be determined with a minimum amount of data. The method consists of calculating equilibrium constants as a function of liquid composition and using the K's to calculate changes in compositiort of injection gas as it successively contacts original resetvoir oil at the gas-oil front and the change in composition of reservoir oil as it is successively contacted by the injection gas in the vicinity of an injection well. An iterative process is required. Two examples of the method are given which show how oil and gas compositions and properties are calculated with the aid of a computer. INTRODUCTION The calculation of recovery from lean-gas or enriched-gas injection into a saturated or under-saturated reservoir oil requires a knowledge of how phase properties change in a reservoir between injection well and producing well. To determine the phase compositions or properties experimentally would be difficult and time consuming, especially if one wanted to look at the effect of various injection gas compositions. For some fields an engineer would want to make preliminary calculations on the economics of gas injection before he makes the decision to spend a corrsiderable sum of money for laboratory work to obtain the necessary fluid properties. A method for calculatine compositions and properties based on a minimum of laboratory data is described. The minimum amount of data required is injection gas and reservoir oil composition and injection gas solubility as a function of pressure for an undersaturated oil, or the compositions of mixtures of reservoir fluid with two or more enriched gases, which mixtures have a bubble-point pressure that is the same as the expected average displacement pressure. On the other hand, if the economics appear to be attractive, more laboratory data can be obtained in the form of equilibrium constants for three or more mixtures of the reservoir fluid and injection gases. The method is based on the calculation of K's from the equation, log Kp = A + B F, where K is equilibrium constant, p is pressure and F is component characterization factor. This method of plotting K data by means of the above equation is described by Hoffman, Crump and Hocott.1 A and B are constants that vary with a composition parameter. It is shown how experimental data are used to determine how A and B vary with composition. BASIS OF METHOD EQUILIBRIUM CONSTANTS Equilibrium constant (K) data are required for this method. The K of each component is obtained from an equation that gives the product of K and pressure as a function of component characterization factor. The characterization factor F = b(l/Tb — l/T), where b is a constant characteristic of a given component, Tb is the boiling point in OR at atmospheric pressure of the given component, and T is the temperature of the system in OR. This method of plotting K data is described by Hoffman, Crump and Hocott.l The straight-line equation of the log Kp - F plot is log hp = log Kop +BFi, where Kop is at F =0, i designates the component, and B is the slope of the line. The factor F can be

Jan 1, 1966

By Robert Wamsley, W. E. Jones

One of the earliest problems in the life of any community is the provision of an adequate supply of water sufficiently free from all types of contamination to be suitable for domestic purposes. Generally speaking, the location of most communities is determined to a great extent by the availability of an adequate supply of satisfactory water. For a mining camp, that consideration cannot be foremost. Here, the ore takes first place, and the men who mine it must do the best they can under the existing conditions. If there is no local source of water, it must be brought from some distant source or must be found by sinking shafts or drilling wells. Fortunate indeed is the mining company that discovers a commercially valuable ore deposit beside a never failing creek full of pure water, with sufficient water rights available. because the acquisition of water in any other manner nearly always involves not only a considerable period of time but the expenditure of considerable money. The experience of Climax Molybdenum Co. demonstrates the measures that sometimes are necessary in order to provide a suitable supply of water. The Climax mine and mill are on the Continental Divide! about 13 miles northeast of Leadville. The elevation of the domestic part of the camp varies from a minimum of 11,320 ft. to a maximum of approximately 11,550 ft. above sea level, and, as is common at such altitudes, the near-by streams that might be suitable for a water supply are small and intermittent, usually flowing only during the summer months. The only streams of any size in the immediate vicinity of Climax are the Ten Mile and Arkansas Rivers The headwaters of Ten Mile River are on the Company's property, and its water has been used for the domestic supply. The headwaters of the Arkansas River are about 2 miles distant and have not been used as a source of supply by the company. During the past 11 years of the production of molybdenum at Climax, the number of families living there has increased from about 45 to 283, and the population has increased from about 200 to 1200 persons. Consequently, the capacity of the water-treatment facilities, and the amount of water available, had to be increased to meet the requirements of the camp. As early as 1932 it was recognized that the water in Ten Mile River would not continue to be adequate for domestic purposes and after considerable discussion it was decided to drive a drift through the major fault in an effort to find additional water. This drift was completed in 1935 and tapped sufficient water to make the supply adequate. This water was treated in a tank underground, where lime was added, and was then piped into the domestic supply lines. At about the time this line was completed, the presence of fluorine in harmful concentrations was discovered in the water. This problem was submitted to the International Filter Co. and in November 1937 a plant of its design was put in operation for treating the water to remove the fluorine. This plant proved entirely successful,

Jan 1, 1946

By W. G. Sinclair

The North Texas district incorporated in this paper corresponds with the Railroad Commission's District No. 9, and includes the counties of Archer, Baylor, Clay, Cooke, Foard, Hardeman, Jack, Knox, Montague, Wichita, Wilbarger, and Young.† Table I,Oil and Gas Production in North Texas District, has been changed to conform with the nomenclature of pools designated by the Commission in order to facilitate compilation of the data, since most of the companies operating in the area are coming more and more to recognize one central authority in the matter of naming each new oil pool. No effort is being made to discuss the structural characteristics of the region, since it is generally known by oil men that most of the oil and gas comes from Pennsyl-vanian, with some of less importance from the Mississippian and Ordovician. Development during 1944 There were 1550 wells drilled during 1944, an increase of 450. Of this number, 677 were completed as oil wells, and 11 as gassers. Production increased 1,505,025 bbl., making the year's total 43,172,005 bbl. of oil having an average gravity of 40". Development generally, however, was somewhat disappointing. The 47 new pools, extensions, or new pay horizons in old fields, had a combined initial production of only 19,146 bbl. It is estimated that these wells added approximately 10,000,000 bbl. to the reserves. The largest single addition to the reserves was in the Caddo conglomerate in the Hildreth pool, Montague County. During the year, 66 wells were completed as the result of three extensions, I to 136 miles west, northwest and north of the field. Young, Archer, and Clay were the most active counties. Eleven new potential - oil fields were developed in Young County, nine in Archer and nine in Clay. Outlook for 1945 In spite of the fact that exploration as a whole was disappointing in 1944, prospects for increased development are bright for 1945. At the close of last year, 2.1 geophysical crews were operating in the district, which, together with the Ohio Oil Company's No. I W. R. Ross, a wildcat Strawn discovery in King County, 1 1/2 miles beyond the west boundary of district 9, stimulated a lease play extending over four counties. Two of them, viz., Foard and Knox, are in the area incorporated in this report. Acknowledgments The writer is indebted to Mr. C. W. Hanley, Zone Agent of the North Texas District, and Mr. William M. Lourcey, head of the Land, Leasing and Scouting Department for the Gulf Oil Corporation, both of Fort Worth, Texas, for permission to prepare this paper.

Jan 1, 1945

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

By J. A. Capp

For certain classes of electric railways a steel conductor is preferable to the oldcr atld more commonly used overhead trolley-wire. The third-rail presents a rather better appearance, because of the absence of an overhead structure; it is easily installed, cheaply maintai~ied, presents s large area for conducting and collecting the current, and is therefore particularly suitable for high speed and heavy service. With costs calculated on the basis of equal coilductirity in rail aud trollej-wire, the third-rail constrrictiol~ is cl~caper than thc overhead trolley. But the average interurban road will lise a trolley-wire of considerably less conductivity than would be obtained with the smallest size steel rail (about 60 lb. per pard) that mould ordinarily be used, and here the first clost of trolley construction would generally be less thau that of the third-rail. While no third-rail installation has jet bee11 in operation long enough to give figurcs of value, it ~vould appear that the cost of maintenance of the thirdrail construction should be less than that of the overhead trolley. This consideration, together with that of sightliness and adaptability (particularly in the case of terminals, yards and very heavy or high-speed service), will frequently off'set the higher cost of the third-rail construction and make it the preferable means of' conducting the current from thc generator to the car-motor. For the first third-rail installations, old track rails were used when obtainable, and these old rails were supple~rlented with new rails of standard T-section and composition. With the coming of the very heavy, high-speed service during the past few years, the resistance of these old and new standard T-rails was found to be so high that they mould not carry the high currents necessary without too great a drop in the line-potential. The rails would, therefore, have to be suppleme~~ted with addi-

Jan 1, 1904

By A. Yoshikawa, T. Sugeno

To detenmine the origin of the sharp fatigue limit in many ferrous metals, S-N curvces were determined in push-pull fatigue at 18.6 kc per sec at room temperature and - 67°C for various kinds of iron. These differed in carbon and nitrogen content and grain size (25 and 2500 grains per sq mm). Sharp knees appeared in the S-N curves of fine-grained specimens with high interstitial content at both temperatures. In coarse-gruined specimens, knees were not sharp .regardless of the interstitial content and the testing temperature. It is concluded from these results that the controlling factov for the appeavance of the sharp fatigue limit is not strain aging but grain size. It has already been mentioned that iron and some iron alloys show fatigue curves characterized by a more or less sharp knee and a fatigue limit.' Explanations of the origin of this characteristic behavior of fatigue in iron appear to fall into two broad classes. One is concerned with interstitial impurities through the aging or locking effect and the other is based on intrinsic plastic properties of iron. Levy and sinclair2 and Lipsit and Horne3 have suggested that the fatigue limit observed generally in iron and steel is due to interstitial solute aging during the course of fatigue. On the other hand, Thompson and wadsworthl have suggested that the fatigue limit may be analogous to the sharp yield point, in the sense that alternating stresses above the fatigue limit are necessary to break down the dislocation locking. However, there are some experimental results which cast doubt on the general validity of these suppositions.4-8 Ferro and Montalenti' have recently suggested that the typical form of the fatigue curve of iron seems to come from an intrinsic plastic characteristic of the iron structure. This suggestion is based on the experimental result that pure iron containing an insufficient amount of interstitial solute to alldw appreciable strain-aging effects still showed a fatigue limit at room temperature. Although systematic investigations on the effect of grain size are scarce, it is thought that this effect is important in relation to the sharp fatigue limit. In fact, sensible differences were observed by Oates and Wilson4 in fatigue behaviors of a low-carbon steel depending on grain size. Ideally, the fatigue limit will be defined as the upper limit of stress amplitudes at which the life is infinite. This ideal fatigue limit can never be determined because of the limited time available for experiments, and moreover scattered data points often leave the construction of S-N curves somewhat arbitrary. And, it is usually stated that a material has a fatigue limit when its statistical S-N curve becomes apparently parallel to the N axis with a more or less sharp knee. The meaning of the fatigue limit and the sharp knee will be discussed in detail in relation to the construction of S-N curves. The origin of this sharp knee was investigated by determining S-N curves of iron for various interstitial contents, testing temperatures, and grain sizes. EXPERTMENTAL PROCEDURE The material as received was a commercial-grade low-carbon steel in the form of 4-mm-diameter rods with the following composition in weight percent: C, 0.09; Si, 0.017; Mn, 0.43; P, 0.006; S, 0.012; Cu, 0.11. Five different groups of specimens were tested. The grain sizes and interstitial contents in each group are given in Table I. The specimens of group C-02 were decarburized by annealing for 100 hr at 700°C, followed by an additional 100 hr at 850°C in wet hydrogen. Specimens of groups N-2 and N-9 nitrided in a mixed atmosphere of ammonia and hydrogen after an initial treatment identical to group C-02. The specimens of group C-9 were prepared in a manner similar to those of group C-02, except heat treatment was carried out in a vacuum. After polishing their surface with emery paper, the specimens of all groups were given a final anneal for 30 min at 930°C and air-cooled in an evacuated quartz tube. For group C*-9 this

Jan 1, 1965

By L. A. Dale, D. A. Dahlstrom

Closed-water circuits are justified today from two standpoints: economical operation and prevention of stream pollution. In today's modern preparation plant, it has been found very desirable to have the plant circulating water maintained at a relatively low solids concentration of around 3%. In so doing, bene-ficiation equipment can operate at a much higher efficiency. However, makeup water requirements would become excessive if the fines were to be removed from the preparation plant by bleeding a 3% solids concentration to a tailings pond. With the ever increasing percentage of —200 mesh coal, clay and slimes in the raw coal, coupled with the creation of these fines within the preparation plant, the need for water conservation for economy reasons becomes even more important. Because of stream pollution laws, tailings ponds have become very costly to operate and maintain, resulting in the necessity of employing an in-plant method of water recovery. Accordingly, the primary system employed in water recovery in the coal preparation plant today consists of a solids concentration device to thicken refuse solids while at the same time producing a sufficiently clarified effluent that can go back to the preparation plant for water reuse. The thickened product is then normally passed to a dewatering device that will produce a handleable solid that can be disposed of

Jan 1, 1965

By H Pray, H. W. Russell, Paul D. MILLER

It is known that austenitic chromium-nickel steels that have free carbide in the grain boundaries are subject to intergranu-lar corrosion. It is difficult to detect such a susceptible condition in a fabricated article because present test methods require a sample section for examination and in most cases this is difficult to obtain. The question of the nature and prevention of intergranular corrosion in austenitic stainless steels has been ably discussed by Bain and co-workers1-3 and by other investigator4-10 The present methods of study subject samples to corrosive conditions in such reagents as the Strauss solution, a mixture of copper sulphate and sulphuric acid. Such tests usually require at least 72 hr. to run. Various methods of measuring the degree of sensitization have been employed, such as the measurement of electrical resistivity, magnetic measuremerits, measurement of the degree of cracking produced on bending over a malldrel, and microscopic studies. The detection of carbides at the grain boundaries by metallographic polishing and etching methods is tedious and requires a skilled operator. A recent report on such methods of carbide detection is given by the American Society for Testing Materials Subcommittee VI of Committee A.-1011 and by Arness.12 The present investigation was undertaken to develop a simple test procedure for detecting carbide precipitation or susceptibility to intergranular corrosion. The test is designed for use in the plant and for the testing of fabricated structures. Carbide precipitation, the factor leading to susceptibility to corrosion, is produced by heating the alloy in the temperature range 800° to 1600°F., as in welding, in improper annealing or in service where such temperatures are met. The connection between such precipitation and susceptibility to corrosion has been thoroughly discussed, as has been the use of stabilizing addition elements to prevent precipitation. Experimental Method A small area of the steel under test is subjected to an anodic treatment in a cell that can be 'lamped Onto a a Or an actual structure. The cell and electrical circuit used are illustrated in Fig. I. The cell C is lead, joined to the steel plate D and insulated from it by a short piece of rubber tubing E. The cell is forced tightly against the steel plate by a spring Or clamping device. The seal formed by the rubber against the steel plate is sufficient to retain the liquid bath inside the cell. The spot treated can be made any shape desired, depending on the shape of the rubber gasket. The cell illustrated polishes a circular spot about 3/8- diameter' The bath consists of 60 per cent (by weight) sulphuric acid to which is added 5 ml. per liter of Glycyrrhiza extract (U.S.P.). The cell requires about 2 to 2.5

Jan 1, 1941