Search Documents

By Bruce H. Gardner, Stephen A. Miller, Shosei Serata

The Bryan Mound salt dome in Freeport, Texas, has some of the largest and oldest solution caverns in the U.S. There are a total of five caverns of varying shapes and sizes randomly distributed throughout the salt dome. When the caverns were converted from a brine production to an oil storage operation, the effects on long-term stability of the caverns and inter-cavern behavior were analyzed to evaluate the future safety of the storage operation. The analysis was based on a worst-possible-case scenario, including accidental wellhead pressure loss. The impact of this pressure loss upon the thinnest partition between the two closest caverns was analyzed, using a case example of storing lightest weight LPG, thereby creating maximum differential pressures between these two caverns. The finite element method with the REM computer code was utilized for this analysis. Results of the analysis illustrate the basic mechanisms of the long-term behavior of the multiple caverns in the LPG storage operation.

Jan 1, 1985

By F. W. Jessen, John C. Miller

In many areas where carbonate rocks form important parts of the stratigraphic sequence, stratigraphers have experienced varying degrees of difficulty in differentiating and correlating limestone and dolomite units in both surface and subsurface work. With early Paleozoic rocks of the Mid-Continent, insoluble residues yield a remarkable amount of strati-graphic data and relatively good correlations may be carried over broad distances.' Unfortunately, neither such information nor electric logs and radioactive logs have been particularly helpful in interpreting the limestone sections of the Permian Basin of West Texas. This is because: (1) the variations in the sections may be very slight; (2) no completely satisfactory method of interpretation has been developed; and (3) the measurements themselves are not sensitive enough for small variations. Also, such logs are influenced by the fluid content. Paleontology and micro-paleontology remain the ultimate arbiters. As a routine tool, however, paleontol-ogical examination is slow and tedious. Chemical analysis may be used, but this, too, is extremely slow. Although rocks are not classified according to chemical composition, there is considerable variation with rock types. Correlation by chemical composition has two advantages, first, the characteristics determined are subject to minimum human error and interpretation, and secondly, the lithologic changes are not masked by fluid content as in the case of electric and radioactive logs. Some fossils concentrate certain elements which tentatively might be used to date rock units.' Rapid chemical analysis by spec-trographic means could be used as an adjunct to other means employed in correlation work, or might, in itself, present a suitable method. PURPOSE OF THIS INVESTIGATION Sloss and Cooke' have published data concerning spectrographic analysis of limestone rocks specifically for purposes of direct correlation of a single formation. These authors found satisfactory evidence that differences in percentage of four elements (Mg, Fe, Al, and Sr) in the Mississippian limestones of northern Montana were useful in carrying out correlation of this formation over a distance of approximately 50 miles. It was concluded from the preliminary work that the spectrochemical method offered possibilities of solution of some problems of correlation heretofore not possible. Since the work of Sloss and Cooke' was confined to one particular limestone zone, extension of the use of the method to examine two or more geologic formations would aid materially in the over-all problem of correlation of such rocks. Equipment is now available commercially with which very rapid spectrographic analyses may be made, and hence the problem was to determine whether the variations existing in the minor constituents of limestones were sufficient for use in possible correlation. Qualitative and semi-quantitative investigations were made to determine whether significant changes in the chemical condition occurred. It was a further purpose to investigate the geologic time-boundaries to see whether significant chemical variation could be found corresponding to the paleontological breaks. It was desirable to attempt correlation of a thick section of limestone or dolomite rock and to have as much information as possible on the section. Furthermore, it was felt that examination of formations more difficult to correlate by other means would enhance the value of the method should definite points of correlation be found. Samples were chosen from the Chapman-McFarlin Cogdell No. 25 well in the Cogdell field, Kent County, Tex., and from the General Crude Oil Co., Coleman No. 193-2 well in the Salt Creek field, Kent County, Tex. These fields belong to the famous series of "Canyon" reef fields of West Texas. Cores from the above wells were available from the United States Geological Survey, Austin, Tex. THE SPECTROGRAPHIC METHOD The choice of procedure to be followed in this investigation was based on the anticipated requirements peculiar to the problem. Since the problem was primarily to investigate the possibilities of applying the spec-trograph to problems of correlation in thick carbonate sections, a precise quantitative analysis did not appear necessary. A qualitative analysis to show the possible absence of presence of any element, or a semi-quantitative analysis of the elements present to show the relative changes in magnitude of selected elements was required. Both types of analysis were employed. The two most widely applied methods of semi-quantitative estimates are those of Harvey and of Slavin4,5 though various other procedures have been described.6 while the Harvey method has been modified by Addink,7 this refinement did not seem necessary to the present problem. Essentially, the procedure employed is a variation of the total energy method of Slavin with two exceptions: (1) stressing matrix effect, and (2) using densitometer measurements. As measured by a densito-

Jan 1, 1956

By Fred E. Carter

AT first sight, the platinum group of metals seem of little import to we, the people," although actually the life of the common man is much influenced by them; this influence is usually indirect, hence his lack of knowledge and interest. He generally associates platinum with high-class jewelry and lets it go at that. Were 11e to go deeper, he would find that platinum metals play their part in his food supply, his clothing. his health, his transportation, his home. And the technical man is in general only slightly better informed, for he usually does not realize how necessary platinum metals are in the manufacture of the many construction materials and chemical products with which he is acquainted. Certainly, our daily lives would be profoundly affected if platinum were suddenly to become unavailable.

Jan 1, 1944

By Andrew B. Crichton

THE oft repeated statements of the United States Geological Survey and the Bureau of Mines that the coal reserves in the United States are sufficient for 3000 yr have given us all a sense of security hard to disturb. If we discount that statement 66 pct, which to the uninformed seems drastic, we would still have 1000 yr supply, and why should mortal man worry about the difference between 1000 and 3000 yr supply of coal. That is exactly the attitude which many who should be better in- formed have taken toward the problem. A recent brochure "How Strong is America," by the New York Herald Tribune, states there is "no end to coal * * The truth is staggering * * U. S. has enough coal to last 4000 years." What the statement actually means is that the calculator got as high as 4000 yr and decided it was pointless to go on. The President's ERP Committee on Natural Resources and others in high places continue to assure the country of our superabundance of coal. In the past few days the “Wall Street Journal" carried an item from Director Boyd of the Bureau of Mines saying that within a hundred years we would need to triple our annual coal production of 6oo,ooo,ooo tons, making it 1,800,000,000 tons annually, and at that rate we had coal reserves sufficient for 1000 yr. In my humble opinion, we cannot now or ever produce 1,800,000,000 tons annually, be- cause we do not have the reserves in the producing districts to do it. Past reckoning in geology may be, as in the Psalms, a thousand years are as yesterday, but the future must be considered more realistically, and "a thousand years" is really a "heck" of a long time. In most developed areas, mining engineers can count the coal reserves in terms of a hundred years or less, and in some important areas now producing large annual tonnages in much under fifty years. They think when they hear of thousands of years coal reserves, reference is made to distant fields and "the fields are always green far away." The estimates of our coal reserves upon which we are relying were made in 1907 under the direction of Marius R. Campbell, Director of the United States Geological Survey. It is apparent this work was not well done. It was necessarily based on rather meager data because of the little development and prospecting as of that date. There were mistakes in the correlation of seams, and they assumed the continuity of thick seams throughout large coal bearing areas where coal often did not exist. The overstatement of coal bearing areas in the Campbell figures are common. The 1907 survey includes all coals over 14 in. in thickness to a depth of 3000 ft. The total coal reserves according to Campbell were 3157.2 billion tons. The production and mining losses that year would amount to -570 million tons and

Jan 1, 1948

By H. D. Kessler, Joseph B. McAndrew

WHEN there is occasion to make structural use of metals at temperatures above 900°C (1652°F), the choice of alloys is severely limited, and those materials which meet special requirements as to density, strength, toughness, and resistance to creep, oxidation, or fatigue at such temperatures are at a premium. Any new type of high temperature alloy which is found to be outstanding with respect to several of these properties is therefore likely to find special applications for which it is uniquely advantageous as compared to other alloys. Such is the case with the 7 titanium-aluminum alloys. This y phase is an intermediate phase based on the composition TiAl, and extends from about 35.5 to 44.5 wt pct Al at temperatures up to 1000°C, above which the field broadens to include 60 pct A1 at 1340°C.' The alloys of principal interest have a narrow melting range, with 7 forming by the peri-tectic reaction, melt + ß=y at about 1460°C. Unlike most intermediate phases, the binary alloys containing titanium and aluminum in approximately equiatomic proportion possess low room temperature hardness,' in addition to which they have low density, good resistance to oxidation, and relatively high modulus of elasticity.' Unpublished work done at Armour Research Foundation showed

Jan 1, 1957

By Ajoy K. Ghose

INTRODUCTION Longwall mining made its debut in Indian coal mining scene around 1900. Despite this headstart, the application of the method has been slow and halting. Currently, there are some 16 operating longwall faces only in different Indian coalfields contributing to perhaps less than 3 percent of the total underground coal production. Ambitious plans for expansion of longwall mining notwithstanding, apprehensions on the cavability of Indian coalmeasure roof rocks and some unsavoury experiences with face collapses in caved longwalla have impeded wider adoption of the technique. Between 1960 and 1983, some 41 caved longwall faces were worked in Jharia, Raniganj, Karanpura and Korba Coalfields in India, of which 6 faces reportedly had collapsed(1). The first powered support longwall face was started in August 1978 at Monidih colliery which marked a major step forward in the introduction of advanced technological system in Indian coal industry. This paper attempts to analyse critically the experiences with longwall ground control in caved longwall faces in India. Experiences from powered support faces at Monidih, Dhemomain and Pathakhera are synthesized to provide an appraisal of the present status of caved longwall faces under the Indian coalmeasure roofs, which thus far have been characterised as “massive”. The geotechnical site factors at the powered support faces are evaluated and conclusions drawn on the pre-assessment of caving characteristics and support resistance required at the faces.

Jan 1, 1984

By C. A. Stetefeldt

In a former paper (Runs., xxi., 286) I described the plant of the Marsac Refinery, and the manipulations of the process, but cou1d not, at the time, give reliable statistical results. To supply the latter is the object of the present paper. I shall give actual facts as correctly as possible, without any bias one way or the other. For all statistics I am indebted to Mr. W. G. Lamb, who has charge of the Marsac lixiviation-plant and refinery; to Mr. A. Luebeck, assayer at the Ontario mill; and to the Daly Office, Salt Lake City.* Before starting on the work of the year 1892, a most careful clean-up was made, and any remnants were charged to the refinery. During 1892 the Marsac lixiviation-works produced 48.8 tons of so-called "regular" sulphides, which contained, on an average, 11,449 ounces of silver per ton; 11.77 ounces of gold per ton; and 569.8 pounds of copper per ton. To this must be added, 266 pounds of sulphides and by-products left over from the product of 1891, which contained 1380 ounces of silver, 1.41 ounces of gold, and 63 pounds of copper. Before giving the results of the clean-up, a general discussion of the items of expense, methods of assaying, etc., is desirable.

Jan 1, 1895

By F. J. Smit

The Tintic Division of Kennecott Copper Corporation operates the Burgin Mine in the East Tintic District near Eureka, Utah, approximately 75 miles south of Salt Lake City. The Division was organized in 1963 to develop concealed replacement orebodies in the area located by Bear Creek Mining Company, Kennecott's domestic exploration subsidiary. Several accounts of the discovery of these orebodies and the general geology of the area have been given (1, 2). The ore is very complex and of varying degrees of oxidation and alteration. The principal metal values are lead, zinc, silver, and cadmium. The Burgin No. 2 shaft was sunk in 1963 to provide access for mining the orebodies. Much of the ore mined after this shaft was sunk was high grade and shipped directly to smelters, but concurrently it was recognized that concentration would be required to upgrade the lower grade ore in the deposits. Accordingly, in January 1967, authorization was received to construct a 500 tpd concentrator. From the beginning it was expected that the characteristics of the mill feed would vary widely and unpredictably as mining progressed. This paper summarizes the characteristics of the ore, the test work upon which the plant design was based, the engineering and construction, and the present operation of the facility eighteen months after startup. ORE CHARACTERISTICS The Burgin ore is a complex assemblage of minerals from replacement of limestone. The replacement and alteration occurred in at

Jan 1, 1970

By C. Wachmann

The theory presented ill this paper makes possible examination of the phenomenological aspect of secondary oil recovery by alcohol flooding. Limitutions of the theory are contingent on three primary assumptions: (1) chemical equilibrium, (2) no fingering, and (5) no dispersion. The second assumption implies one-dimensional flow. In a geometric sense the theory extends the Buckley-Leverett construction to systems of two slightly miscible fluids and to systems of three components. This is made possible by considering single-phase fluids to be made up two phases, namely of an excess of one phase and a negative amount of the other phase. The procedure is discussed in the paper. The theory also permits direct determination of the relationship between the aqueous phase saturation and the concentration of water in the aqueous phase in a zone of variable composition. The velocity of planes of constant water concentration and of constant saturation can be computted likewise and the existence of saturation discontinuities inferred. Consequently the behavior of such a Zone, which may exist at some time between a displaced and a displacing fluid, May be determined. mathematical details are given in Appendices. Problems of experimental verification are pointed out on the basis of a supporting experiment. Implications of the theory and effects of violations of primary assumptions are discussed briefly. The major conclusion is that, if the primary assumptions are met, with pure alcohol and alcohol-rich .slugs piston-like displacement of oil and water is possible. INTRODUCTION The recovery of oil from porous media by alcohol displacement has been studied for several years. Extensive experimental investigations into alcohol flooding have been carried out in the laboratory although little has been done in the field. A large amount of practical information is available, the extent being indicated by the first three papers cited 1-3 and their respecrive bibliographies. This has permitted the Formulation of inferential theories. A more analytical approach in which theories are developed primarily by reasoning from known physical principles and relationships has, however, lagged behind. In fact, an analytically derived theory of alcohol displacement has not been available. The theory presented in this paper on oil and water displacement by alcohol from a porous medium is a result of the analytical approach. The theory is idealized, as certain assumptions had to be made to make the mathematics tractable and reduce complexity of argument. In particular, major assuptions concerning conditions of equilibrium, interfacial stability, longitudinal mixing, etc., led to the exclusion of fingering, for example, from all considerations. In many laboratory experiments reported in the literature fingering could not be avoided. There is, therefore, disagreement between theories based on experimental evidence available and the analytically derived theory presented here. This theory presented is based on known physical data and makes use of the Buckley-Leverett construction and its suggested extension. The mathematical derivation of the theory is given in Appendices. Three examples relevant to alcohol displacement are discussed to explain the use of this theory: (1) system of two immiscible fluids (the Buckley-Leverett case); (2) system of two slightly miscible fluids involving an extension of the Buckley-Leverett construction; and (3) system of three components, including injection of pure alcohol or alcohol-rich fluid as a special case, which involves a more general extension of the Buckley-Leverett construction. In these discussions strict assumptions were made to impose equilibrium conditions and exclude mixing and fingering. Effects of relaxing these assumptions and consequent extensions of the theory are indicated. The complexity of the alcohol displacement process makes experimental verification of the theory essential. Some relevant evidence is offered in this paper.

Jan 1, 1965

By Marlin J. Veesaert

Urban quarries offer one of the greatest opportunities for profit in nonmetallic mining with limited financial risk-if properly evaluated, planned and developed to meet market needs. Location, with respect to market, is the prime consideration. Geologic considerations and quality of rock are nearly as important. Cost factors and return on investment (ROI) are the principal financial considerations. Risk of capital is determined by weighing all factors that should be considered and how well judgments are based on information acquired. It is a simple, true axiom of business that an investment must be founded on amount of capital required with its expected return plus profit, expertise required to operate, and time involved. Urban quarries generally offer excellent stone product market opportunities. Costs of land with mineral containment and processing operations are much greater than in rural areas. Environmental problems have become increasingly severe. Competition from other quarries in the market area is usually directly proportional to the profit attractiveness. Risk of capital (initial, developmental and operational) can be evaluated and reduced only by thorough analysis of the entire situation. Time and money expended on planning and preliminary investigations probably represent the most productive investment of available company resources. Basic Reasons to Establish a Limestone Quarry Profit Motive: Certainly the dominant and overriding motive must be that of attaining a reasonable profit. In certain situations a quarry firm may acquire land, necessary rezoning (if required), and satisfy all of the other prerequisites preparatory to beginning operations but delaying the actual development.

Jan 1, 1980

By H. O. HOPMAN

(Canal Zone Meeting, November, 1910.) I. INTRODUCTION. THE substance of this paper was prepared for the Seventh International Congress of Applied Chemistry, held in London, May, 1909, under the title, Some Developments in Blast-Roasting. In the absence of the author, a -short abstract of the paper was read, and the abstract only will appear in the proceedings of the congress. The present paper has been partly rewritten and considerably enlarged by information gained since the original was prepared ; also some illustrations have been added. Blast-roasting' is a generic term for the process of forcing air through finely-divided. metallic sulphide with the object of roasting and agglomerating in a single operation. At first the process was confined to a galena-concentrate ; lime, limestone, or gypsum was added, to serve both as a diluent to keep separate the particles of galena that they might be thoroughly oxidized, and as a flux that the partly-roasted ore might be agglomerated by the formation of some slag. Later it was extended to treat other metallic sulphides. The leading processes were the Huntington-Heberlein and the Savelsberg of Europe, and the Carmichael-Bradford of Australia. In the United States and Canada, the Huntington-Heberlein process has found application in some instances with galena-concentrates, for which it was originally intended; but this class of ore is not often treated alone, hence the process has had to be modified to suit conditions. The Savelsberg process has been transplanted to this country in about its original form. The Carmichael-Bradford is not used at present. The changes called for in the Huntington-Heberlein process to adapt it to the class of lead-bearing ores usually smelted have been the 1 A. S. Dwight, Engineering and Mining Journal, vol. lxxxv., No. 13, p. 649 (Mar. 28, 1908).

Jun 1, 1910

By D. H. Davis

HAND picking was the earliest form of coal preparation, first practiced to improve the outward appearance of the coal being loaded and to remove any pieces that might appear objectionable to the buyer. It is still extensively practiced on the plus 1-in. sizes and particularly on the plus 4-in. and larger sizes. The percentage of ash reduction that can be obtained by hand picking depends entirely upon the amount of free impurity occurring in the coal. In a particularly dirty seam, where a considerable quantity of rock occurs with the coal as mined, hand picking produces sizable reductions in ash. If the coal is prepared clean at the working face hand picking is a final check; in some cases, on the smaller sizes, it is practiced only to show that an effort is being made to prepare a clean product. Because of the variety and different methods of handling coal, the early plants were not always adapted for e5cient hand picking. At most mines an attempt is made to - remove the visual impurities at one or more of the following places in the surface plant: (1) in the tipple during screening; (2) on picking band, belt, or shaking conveyors; (3) during the loading of the coal as it goes into the railroad car. Whatever the physical arrangements of the plant may be, the usual practice is to run the coal over the screen, picking table or boom at such a rate that each piece of impurity is exposed to the view of the picker. Coal should be uniformly sized and spread out on the table so as not to exceed one particle in depth. The flow should be even in tonnage and the speed of travel should be from 30 to 60 ft. per minute and not exceed 80 ft. per minute. The dirtier the coal, the slower the speed required for a fixed number of pickers. Actually, picking capacity depends on the number of particles per minute that can be picked out and rejected. The percentage of impurity removed is determined by this and the average weight of piece rejected. Handling a mixture of sizes from nut to the largest lump over the same picking table or conveyor is not conducive to efficient separation by hand picking because the lump hides the smaller impurities. Picking tables should not exceed 5 ft. in width, so that a picker on either side will be able to remove impurities from the center of the table. Guards usually are placed at the side of the screen, boom or table, to allow the pickers to stand close enough to remove the impurities without too long a reach.

Jan 1, 1950

By Emory Kemler

The problem of determining the most desirable operating conditions of an oil-well pumping unit or rig front, the selection of the proper material and size of sucker rods, and the design of a pumping unit require that sucker-rod loads be known with a reasonable degree of accuracy. The segregation of rig losses, the proper selection and operation of prime mover and reduction unit, and the analysis of the operation of subsurface equipment require a knowledge of polished-rod horsepower. The investigation of such problems as the instantaneous stresses set up in a pull-rod line or backside crank installation when the well is suddenly hooked on, a study of such problems as the effect of anchoring the tubing on rod load, tubing stresses and rod horsepower, and an analysis of the effect of subsurface equipment on rod loads make it necessary to have a dynamometer that is rugged, which can follow the sudden changes in load without any lag or damping effect, which will record the load in its true position with respect to polished-rod movement, and which will give a card large enough to allow the desired effects to be measured accurately. The inadequacy of the spring or fluid-pressure type of dynamometers has been covered in detail1. The data given show that dynamometers of the spring or fluid-pressure type exert a damping action on the peak loads and the inertia and friction of their load-indicating mechanism introduces a phase lag in recording the load. A dynamometer of that type will not give the load in the correct amount and will not record it in its true position with respect to stroke or time. New Type of Dynamometer Fig. 1 shows a magnetic strain-gage type of dynamometer, to be described in this paper. The strain gage A is used for measuring the load in the polished rod, a washer B and knife edge C take care of initial misalignment and reduce bending in the compression tube of the strain gage. The complete instrument can be transported in the carrying case E.

Jan 1, 1935

By Henry G. Granger

A RESIDENCE of 14 years in the Republic of Colombia, spent in almost continuous traveling and prospecting-trips, has given me an intimate knowledge of the resources of that wonderful country. The man who best knows Colombia is unquestionably General Rafael Reyes, President of the Republic for the past three years, and with seven years more to serve in his present term. Such is the strength of his personality and the wisdom of his policies that his term of office will no doubt endure as long as he is willing to serve. The vastly improved economic situation and the brilliant outlook for Colombia are so directly due to the influence of President Reyes that a few lines concerning him. will not be amiss, if they serve towards a better understanding of his personality. Born of a distinguished ancestry in the mountains of Boyaca, he is now 57 years old, just the age of his friend Porfirio Diaz when be began the work which has placed Mexico in the rank of great modern nations. It was Reyes who came to Washington to protest against the action of the government of the United States of America in reference to the establishment of the Republic of Panama, and, without entering into a discussion of this affair, it can be fairly said that there was not an American in Colombia whose feelings of justice were. not outraged at the government action and subsequent refusal to submit the matter to the impartial judgment of the' Hague. President Reyes is an accomplished linguist, speaking English, French, German, Portuguese, Spanish, and Italian. He has a remarkably. powerful voice, which can readily be heard by a large assemblage. His height is about 6 ft., and his weight exceeds 200 lb. He has clear gray eyes. Reyes was the leader of those who favored the approval of

Sep 1, 1908

By Arnulf Muan, Hobart M. Kraner

Ferromanganese alloys react with aluminu-silica brick in blast furnace hearths and cause the formation of new phases with low refractoriness and consequent failure of the refractory lining. The nature of these reactions is explained on the basis of petrographic observations, thermodynamic data, and Phase equilibrium considerations. Animproued hearth design resulted from these findings. The production of ferromanganese in blast furnaces presents many problems which are not encountered in the production of iron in the same furnaces. One of the most serious of these problems is the rapid failure of refractories caused by their reaction with the ferromanganese metal. The present paper describes such a "hearth attack", its symptoms, causes, and cure. Following an introductory discussion of operating practice in ferromanganese blast furnaces, results are presented of a petrographic examination of samples from a furnace which had to be shut down because of refractory failure. The causes of this failure are then analyzed on the basis of petrographic observations combined with thermodynamic and phase equilibrium data available in the literature. The latter type of data were subsequently used as a guide in recommending improvements in hearth designs which have since proven themselves successful in practical operations. I) FERROMANGANESE BLAST FURNACE PRACTICE It is considered good practice to blow in a furnace on iron and operate it in this way for a period of time preliminary to producing ferrornanganese. During this time, iron generally penetrates the bottom refractories six or more feet below the original working surface of the hearth. Not only does this metal pervade the joints to these depths, but the pores of the refractories are usually also filled by molten iron. The high throughput of the iron furnace provides ample heat to maintain a high temperature in the hearth refractories. This, together with a high ferrostatic pressure, causes porous clay brick of the hearth to shrink. During subsequent use of such a furnace in ferromanganese production, the iron in the pores of hearth brick if; replaced to some extent by ferromanganese. The replacement is usually not complete. This is probably due to the lower metal throughput and lower prevailing temperatures resulting from this in the brick of the hearth bottom. When the ferrornanganese furnace is banked—or when the temperature in the furnace falls due to a furnace delay—-manganese oxidizes even though the atmosphere is largely CO. Considerable expansion accompanies this oxidation of manganese from metal to oxide. The hearth refractories are then subjected to the disintegrating forces of the volume expansion. These forces may in extreme cases be large enough to lift the furnace off its mantle supports as was described in a previous paper.' When cooling takes place slowly, however, and the temperature remains at a fairly high level, the refractories undergo fluxing action by the MnO. This latter reaction and the reduction of SiO2 of the clay brick is the general subject of the present paper. The observations to be described herein were made on a ferromanganese furnace located at the Johnstown plant of Bethlehem Steel Co. The furnace was lined entirely with clay refractories and had operated on iron for 266 days and on ferromanganese for 96 days prior to being taken off because of a hearth wall failure. II) PETROGRAPHIC EXAMINATION AND CHEMICAL ANALYSIS The photograph reproduced in Fig. 1 shws a cross section of the upper part of an 18 by 9 by 4-1/2 in. bottom block removed from the blast furnace. This brick came from a depth of approximately 6 ft below the original working face of the bottom. It will be noted that the 4-1/2 in. dimension is almost the same as when the brick entered the furnace. Three characteristically different zones marked I, II, and III on the print of Fig. 1 are apparent. Results of chemical analyses of the original brick and samples from each of these zones are listed in Table I. Petrographically the various zones were characterized as follows: The central zone marked I was essentially un-reacted brick. The microstructure consisted of fine needles of mullite, and the pores in this entire area were filled with iron. This is characteristic of

Jan 1, 1962

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By T. E. Leontis, D. H. Feisel

MAGNESIUM alloys containing rare earth metals have received considerable attention during the past several years because of the need for light alloys having high strength and creep resistance at elevated temperatures. Although much of the work reported earlier has dealt with alloys containing Mischmetal, it has been shown in two previous papersl, V hat distinctly different effects are produced by various rare earth metals and rare earth metal mixtures on the properties of magnesium. For example, much higher strengths are obtained in magnesium alloys containing didym-ium (essentially neodymium plus praseodymium) than in alloys made with Mischmetal, which contains all the rare earth metals in the proportions in which they occur naturally in the monazite ore. Mg-rare earth metal alloys are characterized by a relatively coarse grain size, which greatly impairs castability. The addition of zirconium as a second alloying ingredient has been shown8,7 to refine the grain size, which also produces a distinct improvement in the strength properties. Certain Mg-Mischmetal-Zr and Mg-Mischmetal-Zn-Zr alloy compositions which are currently being produced commercially have been discussed in dytail by Nelson and Strieter,8,4 who also present some in- formation on a Mg-low Ce-Mischmetal-Zr alloy, and by Nelson.8 A patent issued to Jessup, Emley, and Fisher9 emphasizes the superiority of Mg-didymium-Zn-Zr alloys over the corresponding alloys made with Mischmetal. The purpose of this paper is to present the results of an extensive investigation concerned with the effect of increasing amounts of zirconium on magnesium sand casting alloys containing several different rare earth metal mixtures in varying amounts. The effect of the addition of zinc to some of these alloys is also being reported. Preparation and Testing of Alloys The alloys studied in this investigation were prepared in small laboratory melts according to the melting procedures described by Nelson1" as the Crucible Method. Electrolytic magnesium having the composition shown in Table I was used as the starting material. The rare earth metal alloying ingredients used in preparing these alloys were essentially of the compositions listed in Table 11. Some of the didymium-containing alloys were prepared using a Mg-didymium hardener. The rare earth metal content of this hardener analyzed 1.2 pct Ce, 10.4 pct Pr, 80.8 pct Nd, and 7.6 pct La. The zirconium was added in one of three forms: 1) as sponge zirconium obtained from the Bureau of Mines; 2) as a fused salt consisting of 50 pct ZrCl, and 50 pct alkali chlorides from which the zirconium is reduced by the magnesium; or 3) as a Mg-Zr hardener. The alloying procedures and melt hand-

Jan 1, 1958

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By J. E. Andersen, J. Halpern, C. S. Samis

In the presence of oxygen, galena is oxidized in an aqueous medium containing sodium hydroxide, in accordance with the following reaction: PbS + 2O2 + 3OH ? HPbO2 + SO4 = + H2O A novel method was devised for following this reaction which takes place in an autoclave under oxygen pressure, by measuring the concentration of HPbO2- in the solution with a cathode ray polarograph employing stationary platinum electrodes. Using this procedure a study was made of the kinetics of the reaction, in which the effect of a number of variables, including temperature, oxygen pressure, NaOH concentration, and agitation, on the rate, were determined. The results of this study are described and discussed, in terms of possible mechanisms for the reaction. IT is known that sulphide minerals can be oxidized in aqueous media in the presence of oxygen under pressure. Reactions of this type can be classified in two categories depending upon whether the products of oxidation are insoluble or soluble in the aqueous medium. An example of the first type of reaction is the oxidation of pyrite in alkaline solutions, giving rise to an insoluble iron oxide. The kinetics of this reaction have been investigated and its mechanism established.' It has been applied in the oxidation of iron sulphides present in refractory gold ores to improve the subsequent recovery of gold by cyanida-tion.' The second type of reaction finds application where it is desired to recover the metal by leaching during oxidation. In this case a medium is selected in which the oxidized mineral is soluble. For example, nickel, copper, and cobalt sulphide ores can be treated by oxidation in the presence of a solution of ammonia dissolving the nickel, copper, and cobalt as the metal ammine sulphate salts.:' A similar treatment has also been reported to apply to zinc sulphide ores.' It is known that lead sulphate is soluble in solutions of sodium hydroxide or ammonium acetate. It should therefore be possible to dissolve the lead from galena ores by aqueous oxidation with oxygen under pressure using either of these solutions. The applicability of the ammonium acetate treatment has been investigated and confirmed in a recent study.' The present paper describes the results of a similar study in which the kinetics of the oxidation of galena in sodium hydroxide solutions have been investigated. The object of this investigation was pri- marily to obtain information of a fundamental nature relating to the kinetics and mechanism of this reaction. The use of pulps of comminuted ore in a study of this type is undesirable because of the difficulty in controlling and measuring the surface area. The measurements were therefore made using galena crystals of measured surface area and in this way absolute reaction rates were obtained. The reaction was found to proceed as follows: PbS + 2O2 + 3OH ? HPbO2 + SO4 + H2O [I] The products are sodium plumbite and sodium sulphate salts which dissolve in the aqueous solution. The reaction studies were carried out in an autoclave in which a desired pressure of oxygen was maintained. The reaction was followed by measuring the concentration of lead in the solution with a cathode ray polarograph. The results obtained in this investigation are presented and discussed in the present paper. Experimental Materials: The crystals of galena were obtained from Violamac Mines, Sandon, B. C. The following impurities were indicated by spectrographic analysis carried out by the Provincial Assay Office, Victoria, B. C.: Sn, 0.02 to 0.2 pct; Sb, 0.07 to 0.7; Zn, 0.01 to 0.1; Si, Fe, Mg, As, less than 0.05 pct; Ag, 126 oz per ton, the latter determined by standard fire-assaying procedure. After cutting a specimen measuring approximately 5x7x12 mm, the crystal surfaces were ground parallel to the 100 axes using No. 2 emery, washed with water, and the dimensions were measured with a micrometer. Oxygen gas was of commercial grade and supplied in cylinders by Canadian Liquid Air. Solutions were made up with chemicals of chemically pure grade and distilled water. Equipment: Autoclave: The autoclave used in these studies was constructed of stainless steel and

Jan 1, 1954

By Willard L. Cumings, Benjamin L. Miller

(Glen Summit Meeting, June, 1911.) I. THE CAMAGUEY DEPOSITS. 1. Location. THE Camaguey brown iron-ore deposit covers the top of San Felipe hill, the nearest point of which lies 14 miles NW. of the city of Camaguey. While there are several low flat-topped hills in the vicinity covered with a more or less continuous mantle of brown iron-ore, the deposit of San Felipe hill is the only one of any size and importance, and the name "San Felipe district " is proposed for the region. The deposit extends in a NW-SE. direction for a distance of about 10 miles, with an average width of 5 miles. The location is shown in Fig. 1, a sketch-map of the eastern part of Cuba. Fig. 2 is a map of the San Felipe district. 2. Description. The district is mentioned by Spencer,1 who says: "The Cubitas iron-ore fields are situated from 12 to 15 miles north of Camaguey City, in the province of Camaguey Within an area measuring roughly 10 miles east and west and 4 miles north and south, there are several flat-topped mesas rising 300 to 400 ft. above the level of an almost featureless plain which extends for many miles in all directions except toward the north." With the exception of the discrepancy in his statements as to the distance from Camaguey and the area of the hill, which is over 50 sq. miles, his description is a very good one. Kemp 2 has the following to say of ores in Carnaguey Province * Geologist, Bethlehem Steel Co. + Professor of Geology, Lehigh University. 1 Bulletin No. 540, U. S. Geological Survey, p. 324 (1908). 2 The Iron Ore Resources of the World, printed by the Eleventh International Geological Congress, vol. ii., p. 795 (1910).

Mar 1, 1911